0% found this document useful (0 votes)
59 views2 pages

How To... : Amiga 1000 Without Piggyboard

This document provides instructions for installing a Kickstart Adapter in different versions of the Amiga 1000. It describes cutting conductor paths and soldering wires from chips on the mainboard to the adapter to deactivate the 256kb WOM area. Identical steps are listed for motherboards with and without a Piggyboard to ready the system for a Kickstart ROM.

Uploaded by

Luke Breinig
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
59 views2 pages

How To... : Amiga 1000 Without Piggyboard

This document provides instructions for installing a Kickstart Adapter in different versions of the Amiga 1000. It describes cutting conductor paths and soldering wires from chips on the mainboard to the adapter to deactivate the 256kb WOM area. Identical steps are listed for motherboards with and without a Piggyboard to ready the system for a Kickstart ROM.

Uploaded by

Luke Breinig
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

How to...

This is a quick guide on how to use the Amiga 1000 Kickstart Adapter in your
Amiga. There are different mainboards available so please check with your
revision and follow the instructions for your board.

Amiga 1000 without Piggyboard

First you have to solder a 28-pin socket to position U5R on the mainboard.

Next you have to cut the conductor path between PAL DAUGCAS position U6N Pin
17 and 74LS373 position U3J Pin 1. Alternative you can cut Pin 17 of PAL
DAUGCAS so it has no contact to the board. Now you have to solder one wire
from 74LS373 position U3J Pin 1 to the Kickstart Adapter position 1. These steps
are necessary to deactivate the 256kb WOM area.

Next step is to change the jumpers on position W2 and W4 like it is showed on


the picture below:

x = cut here

Finally you have to solder two wires, one wire from PAL DAUGCAS position U6N
Pin 2 to the Kickstart Adapter position 4, the second wire from PAL DAUGCAS
position U6N Pin 9 to the Kickstart Adapter position 3.
Now you are ready to fit the Kickstart Adapter into position U5S and U5R on the
mainboard. Before installing a Kickstart ROM and switching on the Amiga please
double check all steps.
Amiga 1000 with Piggyboard

First you have to cut the conductor path between PAL DAUGCAS position U6J Pin
17 and 74LS373 position U4K and U4H Pin 1. Alternative you can cut Pin 17 of
PAL DAUGCAS so it has no contact to the board. Now you have to solder two
wires from 74LS373 position U4K Pin 1 and U4H Pin 1 to the Kickstart Adapter
position 1 and position 2. These steps are necessary to deactivate the 256kb
WOM area.

Next step is to change the jumpers on position W2 and W4 like it is showed on


the picture below:

x = cut here

Finally you have to solder two wires, one wire from PAL DAUGCAS position U6J
Pin 2 to the Kickstart Adapter position 4, the second wire from PAL DAUGCAS
position U6J Pin 9 to the Kickstart Adapter position 3.
Now you are ready to fit the Kickstart Adapter into position U5P and U5N on the
mainboard. Before installing a Kickstart ROM and switching on the Amiga please
double check all steps.

Amiga 1000, Rev. A with Piggyboard

First you have to cut the conductor path between PAL DAUGCAS position U6J Pin
17 and 74LS373 position U4K and U4H Pin 1. Alternative you can cut Pin 17 of
PAL DAUGCAS so it has no contact to the board. Now you have to solder one wire
from 74LS373 position U4K Pin 1 and U4H Pin 1 to the Kickstart Adapter position
1 and position 2. These steps are necessary to deactivate the 256kb WOM area.

Next step is to change the jumpers on position W2 and W4 like it is showed on


the picture below:

x = cut here

Finally you have to solder two wires, one wire from PAL DAUGCAS position U6J
Pin 2 to the Kickstart Adapter position 4, the second wire from PAL DAUGCAS
position U6J Pin 9 to the Kickstart Adapter position 3.
Now you are ready to fit the Kickstart Adapter into position U5P and U5N on the
mainboard. Before installing a Kickstart ROM and switching on the Amiga please
double check all steps.

You might also like