This document contains a list of fault codes for an Aquila drilling rig. There are over 1000 fault codes listed organized by system and fault description. Common systems that faults are listed for include power systems, GPS, CAN networks, hydraulic systems, and PLC communication.
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0 ratings0% found this document useful (0 votes)
242 views10 pages
Aquila Fault Code List
This document contains a list of fault codes for an Aquila drilling rig. There are over 1000 fault codes listed organized by system and fault description. Common systems that faults are listed for include power systems, GPS, CAN networks, hydraulic systems, and PLC communication.
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10
Aquila Fault Code List
101 Carousel Not Stowed
104 Breakout Wrench Not Fully Open 105 Rod Catcher Not Retracted 106 Rotary Head Feed Limit 107 Bit Not Above Ground 108 Low Main Lube Tank Level 109 Incomplete Main Lube Cycle 110 Bit Not Above Ground 111 All Jacks Not Fully Retracted 112 Tower Angle Pins Not Locked. 113 Tower Strut Pins Not Locked 114 Tower Vertical Pins Not Locked 115 Bit Not Above Ground 116 Vertical Pins Unlocked 117 Angle Pins And Vertical Pins Locked 118 Strut Pins Locked 119 Bit Not Above Ground 120 Angle Pins Not Locked 121 Tower Not Vertical 122 No Bailing Air Pressure 123 Breakout Wrench Not Stowed 125 Strut Bit in Ground 126 Main Lube Tank Level Empty 127 Incomplete Bit Lube Cycle 130 Rotary Head in Rod Support Zone 131 Rod Support Switch Fault 132 Multiple Tower Switches Activated 133 Deceleration Switch Fault 134 Deceleration Switch Fault 135 Rod Catcher Interference Switch Fault 142 Low Water Tank Level 162 Cab Emergengy Stop 163 Power Pack Emergengy Stop 164 Ground Level Emergengy Stop 180 Air Compressor Warning 181 Air Compressor Shutdown 195 High Hydraulic Oil Temperature 196 High Compressor Oil Temperature 200 Low Hydraulic Tank Level 201 369 Relay Config File Problem 201 Low Fuel Tank Level 202 369 Relay Communication Failure 202 High Engine Coolant Temperature 203 Engine Overspeed 204 ECM Malfunction Indication 205 Major Engine Fault 206 Minor Engine Fault 207 Critical Engine Fault 208 ECM Communication Failure 209 Engine Shutdown Complete 210 Engine Protection Shutdown Imminent 220 Electric Motor Stator Winding Temperature 221 Electric Motor Stator Winding Temperature 222 Electric Motor Stator Winding Temperature 223 Electric Motor Stator Bearing Temperature 224 Electric Motor Stator Winding Temperature 225 Electric Motor Stator Winding Temperature 226 Electric Motor Stator Winding Temperature 227 Electric Motor Stator Bearing Temperature 228 Electric Motor Stator Winding Temperature 229 Electric Motor Stator Winding Temperature 230 Electric Motor Stator Winding Temperature 231 Electric Motor Stator Bearing Temperature 232 Motor Overload 233 Motor Tripped 250 CS Compressor Air Filter Fault 251 NCS Compressor Air Filter Fault 252 CS Engine Air Filter Fault 253 NCS Engine Air Filter Fault 254 Hydraulic Drain Filter Dirty 255 Hydraulic Supply Filter Dirty 300 Cab DCU Com Failure 301 Power Pack DCU Com Failure 302 Tower DCU Com Failure 303 VAB-1 DCU Com Failure 304 VAB-2 DCU Com Failure 305 VAB-3 DCU Com Failure 306 DCU Communication Failure 307 Harness Code Error in DCU 310 Cab DCU Flashing 311 Power Pack DCU Flashing 312 Tower DCU Flashing 313 VAB-1 DCU Flashing 314 VAB-2 DCU Flashing 315 VAB-3 DCU Flashing 333 Pitch Out of range. 333 Pitch Angle Out of Range. 334 Roll Angle Out of Range. 334 Roll Out of range. 350 CAN Initialization Failure 351 CAN Initialization Failure 495 Air pressure reading. 495 Weight On Bit Out Of Range 496 Rotary Torque Out Of Range 496 Pulldown pressure reading. 496 Defective Pulldown pressure sensor or cable. 497 Rotary motor pressure reading. 497 Penetration Rate Out Of Range 497 Defective Rotary motor pressure sensor or cable. 498 Rotation Speed Out Of Range 500 Keyswitch Off 501 Aquila Power Pack Battery Low 502 Aquila Power Pack Battery Charging 506 CC Temperature too high 507 CC Temperature is high. 550 Battery Voltage Marginal. 551 Battery Voltage Critical. 666 DCULink not responding to CAN 667 ECMLink not responding to CAN 668 DCULink and ECMLink not responding 670 CAN buffer full 700 Bit In Hole 701 Target Depth Reached 705 Change Steel Cancelled 800 Lost communication with PLC. 800 Lost communication with PLC 801 Corrupt data packets from PLC. 801 Corrupt data packets from PLC 802 Corrupt data packets from PLC 802 CC address and PLC destination mismatch. 803 PLC message overrun. 803 CC address and PLC destination mismatch 804 PLC message overrun 804 Unknown PLC messages. 805 Lost software communication with the PLC driver. 805 Unknown PLC messages 806 Lost software communication with the PLC driver 806 PLC data packet mismatch. 807 Lost software communication with the PLC driver 807 PLC is polled. 808 PLC data packet mismatch 808 Invalid PLC source address. 809 PLC is being polled 810 Invalid PLC source address 901 Communication With GPS Receiver Lost 901 No GPS Signal 902 Communication With GPS Receiver Lost 902 No GPS Signal 903 Poor GPS Satellite Coverage 903 GPS Lost 904 GPS Lost 904 Poor GPS Satellite Coverage 905 GPS Configuration Flashed 905 GPS Flashing 1000 No Sensor Interface Module 1001 No Sensor Interface Module 2 1002 Sensor Interface Module 1003 Sensor Interface Module 2 1101 Safety Zone Violation 1102 Safety Zone Violation 1103 Bootleg Hole 1104 Carousel Not Stowed
Refurbish Antique Telephones for Fun and Hobby: Step by Step Instructions to Take an Old Telephone and Return It to Its Original Working Order. No Electronics or Telephone Knowledge Needed.