Aa 036301 001
Aa 036301 001
Aa 036301 001
NOTES:
REV. NO. SHT. NO. DRAWING NUMBER INDEX PLANT NO.
THREAD
THREAD
THREAD
THREAD
THREAD
THREAD
LENGTH
LENGTH
LENGTH
LENGTH
LENGTH
LENGTH
2. PLASTIC ANCHOR BOLT SLEEVES SHALL BE USED WHERE
SPECIFIED IN
CONSTRUCTION DRAWINGS. CENTER SLEEVES
AROUND BOLTS.
PROJ.
PROJ.
PROJ.
PROJ.
4d o
PROJ.
PROJ.
4d o
4d o
4d o
Lt
Lt
TOP OF ROUGH TOP OF ROUGH TOP OF ROUGH TOP OF ROUGH TOP OF ROUGH TOP OF ROUGH 3. THE BOTTOM OF ANCHOR BOLTS SHALL BE SECURED TO
CONC. CONC. CONC. CONC. CONC. CONC. PREVENT MOVEMENT OR TILTING OF THE BOLTS DURING
CONCRETE PLACEMENT.
SLEEVE SLEEVE SLEEVE
CUT LINE 4. FULLY THREADED ASTM A36/A36M RODS MAY BE USED TO
( SEE NOTE 8 ) ( SEE NOTE 8 ) ( SEE NOTE 8 )
SL
SL
FABRICATE TYPE 2 OR TYPE 2S ANCHOR BOLTS.
SL
SD SD SD
SL
L
L
6. ANCHOR BOLT DESIGN SHALL COMPLY WITH SAES-Q-005
hef
hef
hef
hef
hef
AND ACI 318-02, APPENDIX D.
hef
do do do do do do
T1
T1
T1
T1
L1
L1
8. ANCHOR BOLT SLEEVES SHALL BE FULLY GROUTED IN
L1
L1
ACCORDANCE WITH SAES-Q-010 AFTER THE BASE PLATE
HAS BEEN POSITIONED.
ASTM A307 ASTM A307 ASTM A36/A36M or ASTM A36/A36M or ASTM A193/A193M or ASTM A193/A193M or 11. INSTALLATION TOLERANCES FOR ANCHOR BOLTS:
ASTM F1554, Gr. 36 ASTM F1554, Gr. 36 ASTM F1554, Gr. 105 ASTM F1554, Gr. 105
ANCHOR BOLTS AND FOUNDATION BOLTS ARE TO BE SET IN
( SEE NOTE 4 ) ( SEE NOTE 4 ) ( SEE NOTE 5 ) ( SEE NOTE 5 ) ACCORDANCE WITH AN APPROVED DRAWING. THEY MUST NOT
VARY FROM THE DIMENSIONS SHOWN ON THE DRAWINGS BY
MORE THAN THE FOLLOWING:
Bolt Properties Type 3 Type 3S IS DEFINED AS THE SET OF ANCHOR BOLTS WHICH RECEIVE
A SINGLE FABRICATED STEEL SHIPPING PIECE .
Table 1- ASTM A307, Grade A Bolt Sizes-Inch Series Table 2 - ASTM A36, ASTM F1554 Grade 36 Anchor Rods-Inch Series Size Stress L1 T1 h efmin. Edge Dist. Spacing h efmin. Edge Dist. Spacing Sleeve
do TP1 Area 6do 100+do/2 (note b) (note c) SD SL ( b ) 1/4-INCH CENTER TO CENTER OF ADJACENT ANCHOR BOLT
Bolt Properties Type 1 Type 1S Bolt Properties Type 2 Type 2S 2do+13 3do 12do 6d o SL+150
2 GROUP .
Max. Proj. h efmin. Length (L) Edge Dist. Spacing h efmin. Length (L) Edge Dist. Spacing Sleeve L1 T1 h efmin. Edge Dist. Spacing h efmin. Edge Dist. Spacing Sleeve (in) ( in ) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm)
Size Stress Size Stress
Lt
do Type TP1 Area ( note c ) Proj.+ hef 4do 100+do/2 Proj.+ hef (note d) (note e) SD SL do TP1 Area 4do 100+do/2 (note b) (note c) SD SL 3/4 10 0.334 51 57 229 114 114 325 130 145 50 175 ( c ) ELEVATION OF THE TOP OF ANCHOR BOLTS + 1/2-INCH.
12d o 6d o SL+150 do+13 2d o 12d o 6d o SL+150
(in) (in) 2 (mm) (mm) (in) (mm) (mm) (mm) (in) (mm) (mm) (mm) (in) 2 (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) 7/8 9 0.462 57 67 267 133 133 325 147 161 50 175
( in ) (mm) ( in ) MAXIMUM ACCUMULATION OF 1/4-INCH PER HUNDRED FEET
( d )
1/2 Hex 1.50 13 0.142 107 152 10 108 76 275 15 127 114 50 125 1/2 13 0.142 26 25 152 108 76 275 127 114 50 125 1 8 0.606 64 76 305 152 152 400 177 202 75 250 ALONG THE ESTABLISHED COLUMN LINE OF MULTIPLE
175 95 325 50 343 195 218 ANCHOR BOLT GROUPS, BUT NOT TO EXCEED A TOTAL OF
5/8 Hex 1.75 11 0.226 115 191 12 110 95 325 17 1/2 127 129 50 5/8 11 0.226 29 32 191 110 127 129 175 1-1/8 8 0.790 70 86 171 171 421 75 250
1 IN ., WHERE THE ESTABLISHED COLUMN LINE IS THE
3/4 Hex 2.00 10 0.334 123 229 14 111 114 325 17 1/2 127 145 50 175 3/4 10 0.334 32 38 229 111 114 325 127 145 50 175 1-1/4 8 1.000 77 95 381 191 191 441 212 234 75 250
ACTUAL FIELD LINE MOST REPRESENTATIVE OF THE
7/8 Hex 2.25 9 0.462 267 15 1/2 113 133 325 18 127 161 50 175 7/8 9 0.462 35 44 267 113 133 325 127 161 50 175 1-3/8 8 1.234 83 105 419 210 210 460 230 250 75 250
131 CENTERS OF THE AS-BULIT ANCHOR BOLT GROUPS ALONG
1 Hex 2.50 8 0.606 139 305 17 1/2 114 152 400 21 139 202 75 250 1 8 0.606 38 51 305 114 152 400 139 202 75 250 1-1/2 8 1.492 89 114 457 229 229 604 260 291 100 375 A LINE OF COLUMNS .
1-1/8 Hex 2.75 7 0.763 146 343 19 1/2 116 171 421 22 1/2 139 218 75 250 1-1/8 7 0.763 42 57 343 116 171 421 139 218 75 250 1-3/4 8 2.082 102 133 533 267 267 642 294 322 100 375 ( e ) 1/4-INCH FROM THE CENTER OF ANY ANCHOR BOLT GROUP
1-1/4 Hex 3.00 7 0.969 154 381 21 127 191 441 23 1/2 149 234 75 250 1-1/4 7 0.969 45 64 381 127 191 441 149 234 75 250 2-1/4 8 3.557 127 171 686 343 343 793 364 386 100 450 TO THE ESTABLISHED COLUMN LINE THROUGH THAT GROUP .
1-3/8 Hex 3.25 6 1.155 162 419 23 140 210 460 24 1/2 160 250 250 1.155 48 70 419 140 210 460 160 75 250 2-1/2 8 4.442 140 191 762 381 381 981 424 468 150 600
75 1-3/8 6 250
( f ) THE TOLERANCE OF PARAGRAPHS b, c AND d APPLY TO
1-1/2 Hex 3.50 6 1.405 170 457 24 1/2 152 229 604 30 1/2 183 291 100 375 1-1/2 6 1.405 51 76 457 152 229 604 183 291 100 375 2-3/4 8 5.425 153 210 838 419 419 1019 459 499 150 600 OFFSET DIMENSIONS SHOWN ON THE PLAN, MEASURED
1-3/4 Heavy Hex 4.00 5 1.899 186 533 28 1/2 178 267 642 32 1/2 206 322 100 375 1-3/4 5 1.899 57 89 178 267 642 206 322 100 375 3 8 6.506 165 229 914 457 457 1057 494 531 150 600 PARALLEL AND PERPENDICULAR TO THE NEARST
533
ESTABLISHED COLUMN LINE FOR INDIVIDUAL COLUMN SHOWN
2 Heavy Hex 4.50 4.5 2.498 202 610 32 203 305 755 37 1/2 228 354 100 450 2 4.5 2.498 64 102 610 203 305 755 228 354 100 450
ON THE PLANS TO BE OFFSET FROM ESTABLISHED COLUMN
2-1/4 Heavy Hex 5.00 4.5 3.248 218 686 35 1/2 229 343 793 40 250 386 100 450 2-1/4 4.5 3.248 70 114 686 229 343 793 250 386 100 450
LINES .
NOTES:
2-1/2 Heavy Hex 5.50 4 3.999 234 762 39 254 381 981 48 297 150 600 2-1/2 4.0 3.999 77 127 762 254 381 981 297 468 150 600
468
( g ) UNLESS SHOWN OTHERWISE, ANCHOR BOLTS ARE SET
2-3/4 Heavy Hex 6.00 4 4.934 250 838 43 279 419 1019 50 319 499 150 600 2-3/4 4.0 4.934 83 140 838 279 419 319 499 150 600
a. MINIMUM EDGE DISTANCE IS MEASURED FROM THE CENTERLINE OF THE
1019 PERPENDICULAR TO THE THEORETICAL BEARING SURFACE
ANCHOR BOLT TO THE EDGE OF THE CONCRETE.
3 Heavy Hex 6.50 4 5.967 266 914 46 1/2 305 457 1057 52 342 531 150 600 3 4.0 5.967 89 152 914 305 457 1057 342 531 150 600 MISALIGNMENT FROM VERTICAL MAY NOT EXCEED 1:40 .
b. EDGE DISTANCE FOR BOLTS WITH SLEEVES MUST BE INCREASED BY ( SD-do )/2
NOTES:
NOTES:
c. SPACING OF BOLTS WITH SLEEVES MUST BE INCREASED BY ( SD-d o)
a. MINIMUM EDGE DISTANCE IS MEASURED FROM THE CENTERLINE OF THE
a. MINIMUM EDGE DISTANCE IS MEASURED FROM THE CENTERLINE OF THE
ANCHOR BOLT TO THE EDGE OF THE CONCRETE.
ANCHOR BOLT TO THE EDGE OF THE CONCRETE. d. TPI = THREADS PER INCH.
b. ASTM A307 BOLT LENGTHS MAY NOT BE AVAILABLE FOR THE LARGER
b. EDGE DISTANCE FOR BOLTS WITH SLEEVES MUST BE INCREASED BY ( SD-do )/2
DIAMETER TYPE 1S BOLTS.
M36x4 817 85 108 432 216 216 525 248 280 100 375
1/2 " thru 1-1/2" Hex Bolt ASTM A563, Gr. A Galvanized to ASTM A153/A153M, M20x2.5 245 33 40 240 110 120 325 125 150 50 175
ASTM A307, Grade A ASME B18.2.1, UNC M42x4.5 97 252 310 100
Heavy Hex Class C or ASTM B695, Class 50 1120 126 504 252 525 281 375
over 1-1/2" Heavy Hex Bolt M24x3 353 37 48 288 112 144 400 138 195 75 250
M48x5 1470 109 144 576 288 288 600 314 340 100 450
1/2 " thru 3" Rod ASME B1.1, UNC, Class 2 ASTM A563, Gr. A Galvanized to ASTM A153/A153M, M27x3 459 40 54 324 114 162 400 138 210 75 250
ASTM A36/A36M M56x5.5
ASME B1.13M Class C or ASTM B695, Class 50 2030 125 168 672 336 336 672 358 380 100 450
M12 thru M72 Heavy Hex M30x3.5 561 43 60 360 120 180 400 143 225 75 250
M64x6 2680 141 192 768 384 384 768 427 470 150 600
1/2 " thru 3" Rod ASME B1.1, UNC, Class 2 Galvanized to ASTM A153/A153M, M36x4 817 49 72 432 144 216 525 176 280 100 375
ASTM A563, Gr. A
ASTM F1554, Gr.36
M72x6 3460 157 216 864 432 432 864 471 510 150 600
Heavy Hex Class C or ASTM B695, Class 50 M42x4.5 1120 55 84 504 168 252 525 197 310 100 375
3/4 " thru 3" Bolts/Rods ASME B1.1, 8 UN, Class 2 ASTM A563, DH Heavy Hex Galvanized to ASTM A153/A153M, M48x5 1470 61 96 576 192 288 600 218 340 100 450
ASTM A193/A193M, Gr. B7
M20 thru M72 ASME B1.13M or ASTM A194/A 194M Class C or ASTM B695, Class 50 M56x5.5 2030 69 112 672 224 336 672 246 380 100 450 NOTES:
3/4 " thru 3" Rod ASME B1.1, 8 UN, Class 2 ASTM A563, DH Heavy Hex Galvanized to ASTM A153/A153M, M64x6 2680 77 128 768 256 384 768 299 470 150 600
a. MINIMUM EDGE DISTANCE IS MEASURED FROM THE CENTERLINE OF THE
ASTM F1554 Gr. 105
M20 thru M72 or ASTM A194/A 194M Class C or ASTM B695, Class 50 M72x6 3460 85 144 864 288 432 864 327 510 150 600 ANCHOR BOLT TO THE EDGE OF THE CONCRETE.
b. EDGE DISTANCE FOR BOLTS WITH SLEEVES MUST BE INCREASED BY ( SD-do )/2
c. SPACING OF BOLTS WITH SLEEVES MUST BE INCREASED BY ( SD-d o) ONSHORE STRUCTURES STANDARDS COMMITTEE
ANCHOR BOLT TYPE
3 d
AB 3S-1-1/2"-100-600-(2) NUMBER OF NUTS
VESSEL SKIRT
PROJ.
07
2 d
d
APP’D. FOR CONST.
BOLT LENGTH ( L )
THIS DRAWING IS NOT TO BE USED FOR CERTIFIED
d CONSTRUCTION OR FOR ORDERING
PROJECTION BY DATE
MATERIAL UNTIL CERTIFIED AND DATED
STD. DWG.
REQUIRED ANCHOR BOLT PROJECTION FOR VERTICAL VESSELS (WITH CHAIRS) PLANT NO. INDEX DRAWING NUMBER SHT. NO. REV. NO.
CADD-02