CHAPTER 12

SHIP STABILITY AND BUOYANCY

Learning Objectives: Recall the terminology used for TRIGONOMETRY

ship stability; the laws of physics and trigonometry used Trigonometry is the study of triangles and the
to determine stability and buoyancy of a ship; and the interrelationship of the sides and the angles of a
effects of buoyancy, gravity, and weight shifts on ship triangle. In determining ship stability, only that part of
stability. trigonometry pertaining to right triangles is used.
Under the guidance of the damage control There is a fixed relationship between the angles of a
assistant, damage control personnel provide the first right triangle and the ratios of the lengths of the sides of
line of defense to ensure your ship is as seaworthy as the triangle. These ratios are known as trigonometric
possible. Your responsibilities may include preparing functions and have been given the following names:
daily draft reports, taking soundings, or perhaps you sine, cosine, tangent, cotangent, secant, and cosecant.
may stand watch operating a ballasting console. The three trigonometric functions required for ship
In this chapter, you will be introduced to the laws stability work are the sine, cosine, and tangent. Figure
of mathematics and physics used to determine the 12-1 shows these trigonometric relations.
buoyancy and stability of a ship. Also, there are various
engineering and mathematical principles that you will Sine
become familiar with as you study this chapter.
Detailed information on these subjects is provided in In trigonometry, angles are represented by the
the Naval Ships’ Technical Manual (NSTM), chapter Greek letter theta (θ). The sine of an angle θ,
079, volume 1, and in NSTM, chapter 096. You can find abbreviated as sin θ, is the ratio expressed when the
additional information on these subjects in side of a right triangle opposite the angle θ is divided
publications you will find listed in the Damage by the hypotenuse. Figure 12-1 shows these
Controlman Advancement Handbook. trigonometric relations.
PRINCIPLES OF STABILITY Therefore, referring to figure 12-1:
sin θ = y/r, or the altitude (y) divided by the
Learning Objectives: Recall the basic functions of
hypotenuse (r)
trigonometry, the terminology used for ship stability,
the effects of buoyancy and gravity on ship stability, and If the hypotenuse (r) is also the radius of a circle,
the effects of weight shifts on ship stability. point P moves along the circumference as the angle
changes in size. As angle θ increases, side y increases
To comprehend the principles of ship stability
in length while the length of the hypotenuse (or radius)
fully, you must have a basic understanding of
trigonometry and the functions of right triangles. remains the same. Therefore, the value of the sine
Generally speaking, the weight of a ship in the water is increases as the angle increases. Changes in the value
“pushing” straight down, and the seawater that it of the sine corresponding to changes in the size of the
displaces is “pushing” straight back up. When no other angle are shown on the sine curve shown in figure 12-2.
forces are acting on the ship, all these forces cancel On the sine curve, the size of the angle is plotted
each other out and equilibrium exists. However, when horizontally and the value of the sine vertically.
the center of gravity moves from directly above the
At any angle, the vertical height between the
center of buoyancy, there is an “inclining moment.”
When this occurs, this force is considered to be at right baseline and the curve is the value of the sine of the
angles to the forces of gravity and buoyancy. An angle. This curve shows that the value of the sine at 30°
understanding of trigonometry is required to is half of the value of the sine at 90°. At 0°, sin θ equals
understand the effects and results of these actions. zero. At 90°, sin θ equals one.

12-1
 POINT
P

HYPOTENUSE
(RADIUS)
r (SIDE
y OPPOSITE 0 )

RIGHT
0 ANGLE
x
(SIDE ADJACENT TO 0 )

y length of the opposite side

sin 0 = =
r length of the hypotenuse
x length of the adjacent side
cos 0 = =
r length of the hypotenuse

y lengthof the opposite side

tan 0 = =
x length of the adjacent side

DCf1201

Figure 12-1. Trigonometric relationships.

1 1

0.5 0.5

0 0 o
o o o
60
o
90
o
180 o 270 360
o
60 90
o
180 o 270 360
cos 0
cos 0

0 (DEGREES) 0 (DEGREES)

-1 -1
DCf1203 DCf1203

Figure 12-2. Sine curve. Figure 12-3. Cosine curve.

Cosine Tangent

The cosine is the ratio expressed by dividing the The tangent of the angle θ is the ratio of the side
side adjacent to the angle θ by the hypotenuse. opposite the angle θ to the side adjacent. Again,
Therefore, referring to figure 12-1: referring to figure 12-1:
cos θ = x divided by r (the adjacent divided by Tan θ = y divided by x (the side opposite θ
the hypotenuse)
divided by the side adjacent θ)
In contrast to the sine, the cosine decreases as the
angle θ becomes larger. This relationship between the PRINCIPLES OF PHYSICS
value of the cosine and the size of the angle is shown by
the cosine curve shown in figure 12-3. At 0° the cosine There are certain principles of physics that you
equals one; at 90° the cosine equals zero; and at 60° the need to know in order to have an adequate
cosine is half the value of the cosine at 0°. understanding of stability. You should be familiar with

12-2
such terms as volume, density, weight, center of Force
gravity, force, and moments.
A force is a push or pull. It tends to produce motion
Volume or a change in motion. Force is what makes something
start to move, speed up, slow down, or keep moving
The volume of any object is determined by the against resistance (such as friction). A force may act on
number of cubic feet or cubic units contained in the an object without being in direct contact with it. The
most common example of this is the pull of gravity.
object. The underwater volume of a ship is found by
Forces are usually expressed in terms of weight units,
determining the number of cubic feet in the part of the such as pounds, tons. or ounces.
hull below the waterline.
Figure 12-4 shows the action of a force on a body.
Density An arrow pointing in the direction of the force is drawn
to represent the force. The location and direction of the
The density of any material, solid or liquid, is force being applied is known as the line of action. If a
number of forces act together on a body, they may be
obtained by weighing a unit volume of the material.
considered as a single combined force acting in the
For example, if you take 1 cubic foot of seawater and same direction to produce the same overall effect. In
weigh it, the weight is 64 pounds or 1/35 of a ton this manner you can understand that F4 in figure 12-4
(1 long ton equals 2,240 pounds). Since seawater has a is the resultant or the sum of the individual forces F1,
density of 1/35 ton per cubic foot, 35 cubic feet of F2, and F3.
seawater weighs 1 long ton.

Weight F

If you know the volume of an object and the

density of the material, the weight of the object is
found by multiplying the volume by the density. The
formula for this is as follows:
W = V x D (weight = volume times density)
When an object floats in a liquid, the weight of the F1
volume of liquid displaced by the object is equal to the F2 F4
weight of the object. Thus, if you know the volume of
F3
the displaced liquid, the weight of the object is found
by multiplying the volume by the density of the liquid. DCf1204
Figure 12-4. Lines indicating direction of force.
Example:
If a ship displaces 35,000 cubic feet of salt water,
the ship weighs 1,000 tons. Whether you consider the individual forces F1, F2,
and F3, or just F4 alone, the action of these forces on
W = V x D (weight = volume times density) the object will move the body in the direction of the
W = 35,000 cubic feet x 1/35 ton per cubic foot force.
W = 1,000 tons To prevent motion or to keep the body at rest, you
must apply an equal force in the same line of action but
Center of Gravity in the opposite direction to F4. This new force and F4
will cancel each other and there will be no movement;
The center of gravity (G) is the point at which all the resultant force is zero. An example of this is a Sailor
the weights of the unit or system are considered to be attempting to push a truck that is too heavy for him to
concentrated and have the same effect as that of all the move. Although the truck does not move, force is still
component parts. being exerted.

12-3
Moments F
d
In addition to the size of a force and its direction of
c
action, the location of the force is important. For
example, if two persons of the same weight sit on
opposite ends of a seesaw, equally distant from the
support (fig. 12-5), the seesaw will balance. However, DCf1206
if one person moves, the seesaw will no longer remain Figure 12-6. Diagram to illustrate the moment of force.
balanced. The person farthest away from the support
will move down because the effect of the force of
his/her weight is greater. A special case of moments occurs when two equal
and opposite forces not in the same line rotate a body.
This system of two forces, as shown in figure 12-7, is
termed a COUPLE. The moment of the couple is the
product of one of the forces times the distance between
them (fig. 12-8).

DCf1205

Figure 12-5. The balanced seesaw.

DCf1207

The effect of the location of a force is known as the Figure 12-7. Equal and opposite forces acting on a body (not
in the same line).
MOMENT OF FORCE. It is equal to the force
multiplied by the distance from an axis about which
you want to find its effect. The moment of a force is the Calculation of the moment of the couple, as shown
tendency of the force to produce rotation or to move the in figure 12-8, is as follows:
object around an axis. Since the force is expressed in The moment of the couple = F x d
terms of weight units, such as tons or pounds, and the Therefore, the moment of the couple is 50 feet
moment is force times distance, the units for moment times 12 pounds that equals 600 foot-pounds.
are expressed as foot-tons, foot-pounds, or
inch-ounces.
F = 50 LBS.
In figure 12-6 the moment of force (F) about the
axis at point a is F times d; d being called the moment
arm. The moment of a force can be measured about any
point or axis; however, the moment differs according to 12 FT
the length of the moment arm. It should be noted that
the moment of a force tends to produce rotary motion.
In figure 12-6, for example, the force F produces a
clockwise rotation. If, at the same time, an equal and
F = 50 LBS.
opposite force produces a counterclockwise rotation, DCf1208
there will be no rotation; and the body is in Figure 12-8. Diagram to show calculation of the moment of a
equilibrium. couple.

12-4
 In one sense, a ship may be considered as a moment, use the ship’s baseline, or keel, as the axis.
system of weights. If the ship is undamaged and Figure 12-11 shows the calculation of the vertical
floating in calm water, the weights are balanced and moment of a 5-inch gun on the main deck of a ship. The
the ship is stable. However, the movement of weight gun weighs 15 tons and is located 40 feet above the
on the ship causes a change in the location of the keel. The vertical moment is thus 15 x 40, or
ship’s center of gravity, and thereby affects the 600 foot-tons.
stability of the ship. 15 TONS
F i g u r e 1 2 - 9 s h ow s h ow a n I N C L I N I N G
MOMENT is produced when a weight is moved
outboard from the centerline of the ship. If the object
weighing 20 tons is moved 20 feet outboard from the

40 FEET
centerline, the inclining moment will be equal to
400 foot-tons (F x d, or 20 x 20).

ORIGINAL w NEW
BASE LINE
POSITION POSITION
DCf1211
Figure 12-11. Vertical moment.

BUOYANCY VERSUS GRAVITY

DIRECTION “Buoyancy” may be defined as the ability of an

OF MOMENT
DCf1209
object to float. If an object of a given volume is placed
Figure 12-9. Inclining moment produced by moving a weight under water and the weight of this object is
outboard. GREATER than the weight of an equal volume of
water, the object will sink. It sinks because the
Figure 12-10 shows how a forward (or aft) FORCE that buoys it up is less than the weight of the
movement of weight produces a TRIMMING object. However, if the weight of the object is LESS
MOMENT. Let’s assume that a 20-ton weight is than the weight of an equal volume of water, the
moved 50 feet forward; the trimming moment object will rise. The object rises because the FORCE
produced is 20 x 50, or 1,000 foot-tons. that buoys it up is greater than the weight of the
object; it will continue to rise until it is partly above
the surface of the water. In this position the object will
t float at such a depth that the submerged part of the
object displaces a volume of water EQUAL to the
w weight of the object.
ORIGINAL NEW
POSITION POSITION As an example, take the cube of steel shown in
figure 12-12. It is solid and measures 1 foot by 1 foot
DIRECTION
OF MOMENT by 1 foot. If you drop the steel cube into a body of
DCf1210 water, the steel cube will sink because it weighs more
than a cubic foot of water. But if you hammer this
cube of steel into a flat plate 8 feet by 8 feet, bend the
Figure 12-10. Trimming moment.
edges up 1 foot all-around, and make the corner seams
watertight, this 6-foot by 6-foot by 1-foot box, as
It is also possible to calculate the VERTICAL shown in figure 12-12, will float. In fact, it will not
MOMENT of any part of the ship’s structure or of any only float but will, in calm water, support an
weight carried on board. In calculating a vertical additional 1,800 pounds.

12-5
 It is obvious that displacement will vary with the
depth of a ship’s keel below the water line that is known
as draft. As the draft increases, the displacement
1' increases. This is indicated in figure 12-13 by a series
1' of displacements shown for successive draft lines on
1' the midship section of a ship. The volume of an
6'
underwater body for a given draft line can be measured
1' in the drafting room by using graphic or mathematical
6' means. This is done for a series of drafts throughout the
DCf1212 probable range of displacements in which a ship is
likely to operate. The values obtained are plotted on a
grid on which feet of draft are measured vertically and
Figure 12-12. A steel cube, and a box made from the same tons of displacement horizontally. A smooth line is
volume of steel.
faired through the points plotted, providing a curve of
displacement versus draft, or a DISPLACEMENT
It is obvious, then, that the volume of the submerged CURVE as it is generally called. An example of this for
part of a floating ship provides the buoyancy to keep the a typical warship is shown in figure 12-14.
ship afloat. If the ship is at rest, the buoyancy (which is
the weight of the displaced water) must be equal to the To use the sample curve shown in figure 12-14 for
weight of the ship. For this reason, the weight of a ship is finding the displacement when the draft is given, locate
generally referred to as DISPLACEMENT, meaning the the value of the mean draft on the draft scale at the left.
weight of the volume of water displaced by the hull. Then proceed horizontally across the diagram to the
displacement curve. From this point proceed vertically
Since weight (W) is equal to the displacement, it is downward and read the displacement from the scale.
possible to measure the volume of the underwater body For example, if you have a mean draft of 26 feet, the
(V) in cubic feet and multiply this volume by the displacement found from the curve is approximately
weight of a cubic foot of seawater to determine what 16,300 tons.
the ship weighs. This relationship may be written as the
following: Reserve Buoyancy
1 The volume of the watertight portion of the ship
(1) W = V ×
35 above the waterline is known as the ship’s reserve
buoyancy. Expressed as a percentage, reserve
(2) V = 35W
buoyancy is the ratio of the volume of the above-water
V = Volume of displaced seawater (in cubic feet) body to the volume of the underwater body. Thus
reserve buoyancy may be stated as a volume in cubic
W = Weight in tons
feet, as a ratio or percentage, or as an equivalent weight
35 = Cubic feet of seawater per ton (For ships, the of seawater in tons. (In tons it is 1/35 of the volume in
long ton of 2,240 pounds is used.) cubic feet of the above-water body.)

WATERLINE DISPLACEMENT

28 FEET 18,000 TONS

24 FEET 14,800 TONS
20 FEET 11,750 TONS
16 FEET 8,800 TONS
12 FEET 5,900 TONS

DCf1213
Figure 12-13. Example of displacement data.

12-6
 32

30
28

26 N
TO
24 PER
ET
FE

DRAFT (FEET)
22 B IC
5 CU
3
20 AT
T ER
18 WA
A LT
S
16 IN
E NT
14 EM
AC
PL
12 DIS

10

8
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
DISPLACEMENT (TONS - IN THOUSANDS)
DCf1214
Figure 12-14. Example of a displacement curve.

Freeboard, a rough measure of reserve buoyancy, The force of gravity is a resultant or composite force,
is the distance in feet from the waterline to the weather including the weights of all portions of the ship’s
deck edge. Freeboard is calculated at the midship structure, equipment, cargo, and personnel. The force
section. As indicated in figure 12-15, freeboard plus of gravity may be considered as a single force, which
draft always equals the depth of the hull in feet. acts downward through the ship’s center of gravity (G).
The force of buoyancy is also a composite force,
which results from the pressure of the water on the
ship’s hull. A good example of this is immersing a
FREEBOARD

container in a tank of water as shown in view A of

RESERVE BUOYANCY
figure 12-16. The container must be held under the
DEPTH OF HULL

WATERLINE water to keep it from rising. View B of figure 12-16

shows the position of the container when it is released.
DRAFT

DCf1215

Figure 12-15. Reserve buoyancy, freeboard, draft, and depth

of hull.

When weight is added to a ship, draft and A

displacement increase in the same amount freeboard
and reserve buoyancy decrease. It is essential to the
seaworthiness of a ship to retain a substantial amount
of reserve buoyancy. Some ships can take more than
their own weight in flooding water aboard without
sinking due to reserve buoyancy.

Center of Buoyancy

When a ship is floating at rest in calm water, it is B

acted upon by two sets of forces: (1) the downward Figure 12-16. A. An immersed container; B. The container
force of gravity and (2) the upward force of buoyancy. forced upward.

12-7
 34
Horizontal pressures on the sides of a ship cancel
32
each other under normal conditions, as they are equal
forces acting in opposite directions (fig. 12-17). The 30

vertical pressure may be regarded as a single 28

SCALE OF FEET - MEAN DRAFTS

force—the force of buoyancy acting vertically upward B)
26 (K
E
through the CENTER OF BUOYANCY (B). B AS
24 VE
O
AB
22
N CY
YA
20 B UO
OF
R
18 N TE
G CE
16

B 14

12

10

8
8 9 10 11 12 13 14 15 16
KB - FEET
DCf1219
Figure 12-19. Curve of center of buoyancy above base.
DCf1217
Figure 12-17. Relationship of the forces of buoyancy and
gravity.
To read KB when the draft is known, start at the
When a ship is at rest in calm water, the forces of proper value of the draft on the scale at the left
buoyancy (B) and gravity (G) are equal and lie in the (fig. 12-19) and proceed horizontally to the curve.
same vertical line, as shown in figure 12-17. The center Then drop vertically downward to the baseline (KB).
of buoyancy, being the geometric center of the ship’s Thus, if our ship were floating at a mean draft of
underwater body, lies on the centerline and usually 19 feet, the KB found from the chart would be
near the midship section, and its vertical height is approximately 11 feet.
usually a little more than half the draft. As the draft
INCREASES, B rises with respect to the keel. Inclining Moments
Figure 12-18 shows how different drafts will create
different values of the HEIGHT OF THE CENTER OF A ship may be disturbed from rest by conditions
BUOYANCY FROM THE KEEL (KB). A series of which tend to make it heel over to an angle. These
values for KB (the center of buoyancy from the keel) is conditions include such things as wave action, wind
obtained and these values are plotted on a curve to pressures, turning forces when the rudder is put over,
show KB versus draft. Figure 12-19 shows an example recoil of gunfire, impact of a collision or enemy hit,
of a KB curve for a warship. shifting of weights on board, and addition of off-center
weights. These conditions exert heeling moments on
the ship that may be temporary or continuous.
C
L
When a disturbing force exerts an inclining
moment on a ship, there is a change in the shape of the
24 FOOT WATERLINE
ship’s underwater body. The underwater volume is
20 FOOT WATERLINE relocated, its bulk being shifted in the direction of the
16 FOOT WATERLINE heel. This condition causes the center of buoyancy (B)
B 24
B 20 to leave the ship’s centerline and shift in the direction
B 16
of the heel. (The center of buoyancy moves to the
BASE LINE geometric center of the new underwater body.) As a
K result, the lines of action of the forces of buoyancy and
DCf1218
gravity separate and in doing so exert a MOMENT on
Figure 12-18. Successive centers of buoyancy (B) for different the ship. This moment tends to restore the ship to an
drafts. even keel.

12-8
 If you study figure 12-20, you will notice that a However, it is possible for conditions to exist which
RIGHTING or RESTORING MOMENT is present. do not permit B to move far enough in the direction in
This righting moment is caused by the two equal and which the ship rolls to place the buoyant force outboard
opposite forces, each of W tons (displacement) of the force of gravity. The moment produced will tend
magnitude, separated by a distance GZ, which to upset the ship, rendering it unstable. Figure 12-21
constitutes the LEVER ARM OF MOMENT. Figure shows an unstable ship in which the relative positions of
12-20 shows that the ship is stable because the center of B and G produce an UPSETTING MOMENT. In this
buoyancy (B) has shifted far enough to position the illustration it is obvious that the cause of the upsetting
buoyant force where it tends to restore the ship to an moment is the high position of G (center of gravity) and
even keel or an upright position. the GEOMETRIC CENTER OF THE UNDERWATER
BODY (B—the center of buoyancy).

DIRECTION OF
RIGHTING MOMENT
ANGLE FORCE OF BUOYANCY
DIRECTION OF
OF
UPSETTING
HEEL
ANGLE MOMENT
OF
HEEL Z G
G Z

FORCE OF GRAVITY
FORCE OF GRAVITY

DCf1220

Figure 12-20. Development of righting moment when a stable DCf1221

ship inclines. Figure 12-21. Development of an upsetting moment when an
unstable ship inclines.

A moment is the product of a force tending to

produce a rotation about an axis times its distance from Metacenter
the axis. If two equal and opposite forces are separated A ship’s METACENTER (M) is the intersection of
by a distance, the moment will become a couple which two successive lines of action of the force of buoyancy,
is measured by ONE of the forces times the distance as the ship heels through a very small angle.
that separates them. The RIGHTING MOMENT of a Figure 12-22 shows two lines of buoyant force. One of
ship is therefore the product of the force of buoyancy these represents the ship on even keel, the other at a
times the distance GZ (fig. 12-20) that separates the small angle of heel. The point where they intersect is
forces of buoyancy and gravity. It may also be the initial position of the metacenter. When the angle of
expressed as the force of gravity (weight of the ship) heel is greater than the angle used to compute the
times GZ. The distance GZ is known as a ship’s metacenter, M moves off the centerline and the path of
movement is a curve.
RIGHTING ARM. Putting this into mathematical
terms, you have the following:
M
Righting moment = W x GZ (expressed in ANGLE OF HEEL
IS EXAGGERATED
foot-tons) CL

Where: WATERLINE
UPRIGHT

W = displacement in tons WATERLINE

B1 B2 INCLINED
TO A VERY
GZ = righting arm in feet SMALL
ANGLE

For example, if a ship displaces 10,000 tons and

has a 2-foot righting arm at 40° inclination, the righting BUOYANT FORCE BUOYANT FORCE
UPRIGHT INCLINED
moment is 10,000 tons times 2 feet, or 20,000
foot-tons. These 20,000 foot-tons represent the force, DCf1222

which tends to return the ship to an upright position. Figure 12-22. The metacenter.

12-9
 The INITIAL position of the metacenter is most The ship’s METACENTRIC HEIGHT (GM) is not
useful in the study of stability, because it provides a only a measure of the ship’s RIGHTING ARM (GZ)
reference point when the ship is upright and most but is also an indication of whether the ship is stable or
stable. In our discussion we will refer to initial position unstable. If M is above G, the metacentric height is
of M. The distance from the center of buoyancy (B) to positive, the moments which develop when the ship is
the metacenter (M) when the ship is on even keel is the inclined are RIGHTING MOMENTS, and the ship is
METACENTRIC RADIUS. stable, as shown in view A of figure 12-23. But if M is
below G, the metacentric height is negative, the
Metacentric Height moments that develop are UPSETTING MOMENTS,
and the ship is unstable, as shown in view B of
The distance from the center of gravity (G) to the figure 12-23.
metacenter is known as the ship’s METACENTRIC
HEIGHT (GM). Figure 12-23, view A, shows a ship Influence of Metacentric Height
heeled through a small angle (the angle is exaggerated
in the drawing), establishing a metacenter at M. The If the metacentric height (GM) of a ship is large,
ship’s righting arm is GZ, which is one side of the the righting arms that develop, at small angles of heel,
triangle GZM. In this triangle GZM, the angle of heel is will be large. Such a ship is “stiff” and will resist roll.
at M. The side GM is perpendicular to the waterline at However, if the metacentric height of a ship is small,
even keel, and ZM is perpendicular to the waterline the righting arms that develop will be small. Such a
when the ship is inclined. ship is tender and will roll slowly.
M

In ships, large GM and large righting arms are

ANGLE M
desirable for resistance to damage. However, a
OF
HEEL ANGLE OF HEEL smaller GM is sometimes desirable for a slow, easy
G Z
roll that allows for more accurate gunfire; therefore,
the GM value for a naval ship is the result of
G Z compromise.
B

CL
Inclining Experiment

The ship designer uses calculations to determine

the vertical position of the center of gravity. From
A
available plans and data, the various items that go to
make up the ship and its load are tabulated. The ship
CL can be considered as consisting of the various parts of
the structure, machinery, and equipment. The load is
comprised of fuel, oil, water, ammunition, and sundry
G
stores aboard.
Z

Although the position of the center of gravity as

M
estimated by calculation is sufficient for design
purposes, an accurate determination is required to
B
establish the overall stability of the ship when it is
operating. Therefore, an inclining experiment is
performed to obtain accurately the vertical height of
B DCf1223 the center of gravity above the keel (KG) when the ship
Figure 12-23. A. Stable condition, G is below M; B. Unstable is completed. An inclining experiment consists of
condition, G is above M. moving one or more large weights across the ship and
measuring the angle of list produced. This angle of list
It is evident that for any given angle of heel, there usually does not exceed 2°. The ship should be in the
will be a definite relationship between GM and GZ best possible condition for the inclining. The naval
because GZ = GM sin θ. Thus GM acts as a measure of shipyard or building yard at which the inclining
GZ, the righting arm. experiment is to be performed issues a memorandum to

12-10
the commanding officer of the ship outlining the Q5. What measurement is known by the term
necessary work to be done by the ship’s force and by freeboard?
the yard to prepare the ship for the inclining.
1. Distance in feet from the keel to the
The results of the experiment are furnished to each waterline
ship as a “booklet of inclining experiment data.” This
2. Distance from the waterline to the weather
booklet contains data on displacement, the center of
gravity above the keel (KG), and overall stability for deck edge
the operating conditions of load. Detailed information 3. Distance from the bow to the stern
on the inclining experiment can be obtained from
Naval Ships’ Technical Manual (NSTM), chapter 096, 4. Distance from the portside to the
“Weights and Stability.” starboard side of the ship
Q6. Which of the following information is NOT
REVIEW QUESTIONS contained in the “booklet of inclining
experiment data?”
Q1. Detailed information on the laws of 1. Data on displacement
mathematics and physics used to determine 2. The center of gravity above the keel
the buoyancy and stability of a ship are
3. Reserve buoyancy
provided in Naval Ships’ Technical Manual
4. Overall stability
(NSTM), chapter 079, volume 1, and in
NSTM, chapter 096.
1. True ANALYSIS OF STABILITY
2. False Learning Objectives: Recall the laws of physics and
Q2. Which of the following trigonometric trigonometry used to determine stability and buoyancy
of a ship; and the effects of buoyancy, gravity, and
functions is NOT used for making
weight shifts on ship stability.
calculations to determine a ship’s stability?
To analyze stability principles, you must be
1. Cosine familiar with the terms, definitions, and equations that
are used to express important relationships. These are
2. Sine
listed below.
3. Tangent
• G, the ship’s center of gravity, is the point at which
4. Cotangent all weights of the ship may be considered to be
concentrated. The force of gravity is considered
Q3. Which of the following terms best defines
as acting straight downward, through the center of
force multiplied by the distance from an axis gravity, at right angles to the waterline.
about which you want to find its effect?
• B, the ship’s center of buoyancy, is at the
1. Moment of force geometric center of the ship’s underwater hull.
When a ship is at rest in calm water, the forces of
2. Friction
B and G are equal and opposite, and the points B
3. Ballast and G lie in the same vertical line. When the ship
4. Inclining moment is inclined, B and G move apart, since B moves
off the ship’s centerline as a result of the change
Q4. The volume of water that is moved by the hull in the shape of the underwater hull.
of a ship is known as “displacement.” • M, the ship’s metacenter, is a point established
1. True by the intersection of two successive lines of
buoyant force as the ship heels through a very
2. False small angle.

12-11
 • GM, metacentric height, is the distance from G Righting moments are measured in foot-tons. Since
to M; it is measured in feet. Z is the point at the righting arm (GZ) is equal to GM times sin θ, for
which a line, through G, parallel to the waterline, small values of θ, you can say that the righting
intersects the vertical line through B. moment is equal to W times GM times sin θ. Because
• GZ, the distance from G to Z, is the ship’s righting of the relationship between righting arms and righting
arm; it is measured in feet. For small angles of moments, it is obvious that stability may be expressed
heel, GZ may be expressed by the equation either in terms of GZ or in righting moments.
However, you must be very careful not to confuse
• GZ = GM sin θ
righting arms with righting moments; they are NOT
• W is the weight (displacement) of the ship; it is identical.
measured in long tons.
STABILITY CURVES
• K is a point at the bottom of the keel, at the
midship section, from which all vertical When a series of values for GZ (the ship’s righting
measurements are made.
arm) at successive angles of heel are plotted on a graph,
• KB is the vertical distance from K to the center of the result is a STABILITY CURVE. The stability
buoyancy when the ship is upright. KB is curve, as shown in figure 12-24, is called the CURVE
measured in feet. OF STATIC STABILITY. The word static indicates
• KG is the vertical distance from K to the ship’s that it is not necessary for the ship to be in motion for
center of gravity when the ship is upright. KG is the curve to apply. If the ship is momentarily stopped at
measured in feet. any angle during its roll, the value of GZ given by the
curve will still apply.
• KM is the vertical distance from K to the
metacenter when the ship is upright. KM is NOTE
measured in feet. T h e s t a b i l i t y c u r ve i s c a l c u l a t e d
The RIGHTING MOMENT of a ship is W times graphically by design engineers for values
GZ, that is, the displacement times the righting arm. indicated by angles of heel above 7°.
3
GZ(RIGHTING ARM) IN FEET

0 10 20 30 40 50 60 70 80 90
ANGLE OF HEEL, IN DEGREES

G G Z G Z G Z G
WATERLINE
B B B B
B

o
ANGLE OF HEEL = 0
o
ANGLE OF HEEL = 20 ANGLE OF HEEL = 40
o
ANGLE OF HEEL = 60 o ANGLE OF HEEL = 70
o

GZ = 0 GZ = 1.33 FEET GZ = 2.13 FEET GZ = 1 FOOT GZ = 0

DCf1224

Figure 12-24. Curve of static stability.

12-12
 To understand this stability curve, it is necessary to A reduction in the size of the righting arm usually
consider the following facts: means a decrease in stability. When the reduction in GZ
is caused by increased displacement, however, the total
1. The ship’s center of gravity does NOT change
position as the angle of heel is changed. effect on stability is more difficult to evaluate. Since the
RIGHTING MOMENT is equal to W times GZ, it will
2. The ship’s center of buoyancy is always at the be increased by the gain in W at the same time that it is
geometric center of the ship’s underwater hull. decreased by the reduction in GZ. The gain in the
3. The shape of the ship’s underwater hull changes righting moment, caused by the gain in W, does not
as the angle of heel changes. necessarily compensate for the reduction in GZ.

If these three facts are considered collectively, you In summary, there are several ways in which an
will see that the position of G remains constant as the increase in displacement affects the stability of a ship.
ship heels through various angles, but the position of B Although these effects occur at the same time, it is best
changes according to the angle of inclination. When to consider them separately. The effects of increased
the position of B has changed so that B and G are not in displacement are the following:
the same vertical line, a righting arm GZ must exist. 1. RIGHTING ARMS (GZ) are decreased as a
The length of this righting arm depends upon the angle result of increased draft.
at which the ship is inclined (fig. 12-25). GZ increases
as the angle of heel increases, up to a certain point. At 2. RIGHTING MOMENTS (foot-tons) are
about an angle of 40°, the rate of increase of GZ begins decreased as a result of decreased GZ.
to level off. The value of GZ diminishes and finally 3. RIGHTING MOMENTS are increased as a
reaches zero at a very large angle of heel. result of the increased displacement (W).

Cross Curves of Stability

FORCE OF BUOYANCY AT
The position of the center of buoyancy at any given
18 FOOT DRAFT AND 20o HEEL
20
o angle of inclination depends upon the draft. As the
26 FOOT WATERLINE AT 20 o ANGLE OF HEEL
Z
26
draft increases, the center of buoyancy moves closer to
20o G Z18 18 FOOT WATERLINE AT 20o ANGLE OF HEEL
B
26
26 F
OOT
the center of gravity, thereby reducing the length of the
WAT
B 18 18 F
OO
TW
ERL
INE
AT E
righting arms. To determine this effect, the design
ATE VEN
RLIN
E AT
EVE
KEE
L activity inclines a line drawing of the ship’s lines at a
FORCE OF BUOYANCY AT NK
26 FOOT DRAFT AND 20o HEEL EEL given angle, and then lays off a series of waterlines on
DCf1225
it. These waterlines are chosen at evenly spaced drafts
throughout the probable range of displacements. For
each waterline the value of the righting arm is
calculated, using an ASSUMED center of gravity,
Figure 12-25. Effect of draft on righting arm. rather than the TRUE center of gravity. A series of such
c a l c u l a t i o n s i s m a d e f o r va r i o u s a n g l e s o f
Effect of Draft on Righting Arm heel—usually 10°, 20°, 30°, 40°, 50°, 60°, 70°, 80°,
and 90°—and the results are plotted on a grid to form a
A change in displacement will result in a change of series of curves known as the CROSS CURVES OF
draft and freeboard; and B will shift to the geometric STABILITY.
center of the new underwater body. At any angle of Figure 12-26 is an example of a set of cross curves.
inclination, a change in draft causes B to shift both Note that, as draft and displacement increase, the
horizontally and vertically with respect to the keel. The curves all slope downward, indicating increasingly
horizontal shift in B changes the distance between B smaller righting arms.
and G, and thereby changes the length of the righting The cross curves are used in the preparation of
arm, GZ. Thus, when draft is increased, the righting stability curves. To take a stability curve from the cross
arms are reduced throughout the entire range of curves, draw a vertical line (such as line MN in
stability. Figure 12-25 shows how the righting arm is fig. 12-26) on the cross curve sheet at the displacement
reduced when the draft is increased from 18 feet to 26 that corresponds to the mean draft of the ship. At the
feet when the ship is inclined at an angle of 20°. intersection of this vertical line with each cross curve,

12-13
 N. B. B. 263-16
NEVERSAIL
INCLINING EXPERIMENT, U. S. S. (Sheet of )

Axis assumed feet above base line

Vessel considered water-tight to Taken from Plan No. Buships No.
Scale of Tons Displacement

9,000 10,000 11,000 M 12,000 13,000 14,000 15,000

NATURAL SINE
ANGLE SINE ANGLE SINE
0 0 50 .7660
10 .1736 60 .8660
20 .3420 70 .9397
30 .5000 80 .9948
40 .6428 90 1.0000
6
o
50
40
o (e)

5 60o
o
50
o (d) (f)
70 40o
30
o
(g) 60
o

(c) o
4 70
Scale of Righting Arms - Feet

o
30 o
80
(h)
80o
o
20
3 (b)
o o
90 20
o
90
(i)
2
o
10
o
10
(a)
1

0
N

DCf1226

Figure 12-26. Example of cross curves of stability.

read the corresponding value of the righting arm on the ship’s center of gravity (G). To use a curve taken from
vertical scale at the left. Then plot this value of the the cross curves, therefore, it is necessary to correct the
righting arm at the corresponding angle of heel on the curve for the ACTUAL height of G above the keel
grid for the stability curve. When you have plotted a (KG). If the distance KG is not known and a number of
series of such values of the righting arms from 10° to weights have been added to or removed from a ship,
90° of heel, draw a smooth line through them and you
KG can be found by the use of vertical moments. A
have the UNCORRECTED stability curve for the ship
at that particular displacement. vertical moment is the product of the weight times its
vertical height above the keel. As far as the new center
In figure 12-27, curve A represents an uncorrected of gravity is concerned, when a weight is added to a
stability curve for the ship while operating at
system of weights, the center of gravity can be found
11,500 tons displacement, taken from the cross curves
shown in figure 12-26. This stability curve cannot be by taking moments of the old system plus that of the
used in its present form, since the cross curves are new weight and dividing this total moment by the total
made up on the basis of an assumed center of gravity. In final weight. Detailed information concerning changes
actual operation, the ship’s condition of loading will in the center of gravity of a ship can be obtained from
affect its displacement and therefore the location of the Naval Ships’ Technical Manual (NSTM), chapter 096.

12-14
 6 At 70°, the corrected GZ = 0.5412
5 (e) At 80°, the corrected GZ = minus 0.4392
(d) (f)
RIGHTING ARM IN FEET

(c) (g) It is not necessary to figure the corrected GZ at 90°,

4
since the value is already negative at 80°. When the
(h) values from 10° through 80° are plotted on the grid and
3
(b) joined with a smooth curve, the CORRECTED
A
(i)
2 stability curve (B) shown in figure 12-27 results. As
(a) you can see, the corrected curve shows maximum
1 stability to be at 40°; it also shows that an upsetting
arm, rather than a righting arm, generally exists at
0 10 20 30 40 50 60 70 80 90 angles of heel in excess of 75°.
B
ANGLE OF HEEL IN DEGREES EFFECTS OF LOOSE WATER
DCf1227
When a tank or a compartment in a ship is partially
Figure 12-27. A. Uncorrected stability curve taken from cross
curves; B. Corrected stability curve.
full of liquid that is free to move as the ship heels, the
surface of the liquid tends to remain level. The surface
of the free liquid is referred to as FREE SURFACE.
Suppose that the cross curves are made up on the The tendency of the liquid to remain level as the ship
basis of an assumed KG of 20 feet and that you heels is referred to as FREE SURFACE EFFECT. The
determine that the actual KG is 24 feet for the particular term LOOSE WATER is used to describe liquid that has
condition of loading. This means that the true G is 4 feet a free surface; it is NOT used to describe water or other
higher than the assumed G and that the righting arm liquid that completely fills a tank or compartment and
(GZ) at each angle of inclination will be SMALLER thus has no free surface.
than the righting arm shown in figure 12-27 (curve A) Free Surface Effect
for the same angle. To find the new value of GZ for each
angle of inclination, multiply the increase in KG (4 feet) Free surface in a ship causes a reduction in GM, due
to a change in the center of gravity, and a consequent
by the sine of the angle of inclination, and SUBTRACT
reduction in stability. The free surface effect is separate
this product from the value of GZ shown on the cross
from and independent of any effect that may result
curves or on the uncorrected stability curve. In order to
merely from the addition of the weight of the liquid.
facilitate the correction of the stability curves, a table
When free surface exists, a free surface correction must
showing the necessary sines of the angles of inclination
be included in stability calculations. However, when a
is included on the cross curves form.
tank is completely filled so that there is no free surface,
Next, find the corrected values of GZ for the the liquid in the tank may be treated as a solid; that is, the
various angles of heel shown on the stability curve (A) only effect of the liquid on stability is the effect of its
in figure 12-27, and plot them on the same grid to make weight at its particular location.
the corrected stability curve (B) shown in figure 12-27.
To understand the actions that occur because of
At 10°, the uncorrected value of GZ is 1.4; free surface effect, use a centerline compartment that is
therefore, the corrected GZ at 10° is 1.4 minus partially full of water, as shown in figure 12-28, as an
(4 x 0.1736), or 0.7056. example.
At 20°, the uncorrected value of GZ is 2.8; L4
therefore, the corrected GZ at 20° is 2.8 minus L3

(4 x 0.3420), or 1.4320. L2

W1 L1
Repeating this process at 30°, 40°, 50°, 60°, 70°, W L
W2
and 80°, the following values are obtained: W3
l4
w l
W4 F
w
At 30°, the corrected GZ = 2.2000 4
D
E

At 40°, the corrected GZ = 2.3288

At 50°, the corrected GZ = 2.2360 DCf1228

At 60°, the corrected GZ = 1.4360 Figure 12-28. Effects of free surface.

12-15
 To begin with, the ship is floating on an even keel at overhead and causes a reduction in the breadth of the
waterline WL. Then the compartment is flooded to free surface.
waterline W1. Assuming that the water enters the To understand how pocketing of the free surface
compartment instantaneously and that it is reduces the free surface effect, study figure 12-29.
instantaneously frozen solid, the effects of this frozen View A of figure 12-29 shows a compartment in
body of water are the same as if a solid weight had been which the free surface effect is NOT influenced by the
added. The ship undergoes parallel sinkage and comes depth of the loose water. The compartment shown in
to rest at a new waterline W1L1. view B, however, contains only a small amount of
Now suppose that an outside force acts on the ship, water. When the ship heels sufficiently to reduce the
causing it to heel over at a small angle of list to a new waterline in the compartment from w1 to W1l1, the
waterline W2L2. If at the same time the liquid is freed breadth of the free surface is reduced and the free
from its frozen state, it will run toward the low side of surface effect is thereby reduced. A similar reduction
the compartment until the surface of the water in the in free surface effect occurs in the almost full
compartment shown in view C, again because of the
compartment is parallel to the existing waterline
reduction in the breadth of the free surface. As figure
W2L2. A wedge of liquid is thus shifted from one side
12-29 shows, the beneficial effect of pocketing is
of the compartment to the other; as a result, the center
greater at larger angles of heel.
of gravity of the liquid is shifted from D to E. As the
center of gravity of the liquid is shifted outboard, an
additional inclining moment is created. This causes the
ship to list to a new waterline W3L3.
The additional list, in turn, causes a further shift of
w
the liquid in the compartment and a further shift of the w1 l1
center of gravity of the liquid. As the center of gravity l

of the liquid shifts to F, another inclining moment is

A PARTIALLY FULL
created and the ship lists even more. Eventually the
ship will come to rest with a waterline such as W4L4.
This will occur when the righting moment of the ship is
equal to the combined effects of (1) the original
inclining moment created by the outside force and (2)
the inclining moment created by the shift of liquid
w
within the compartment. l1
w1 l
Location of Free Surface
B SHALLOW
The free surface effect is independent of the
location of the free surface within the ship. A free
surface with a certain length and breadth will, at any
given angle of heel, cause the same reduction in GM w l1
w1
(and, therefore, the same loss of stability) no matter l
where it is in the ship—forward or aft, high or low, on
the centerline or off the centerline.
C ALMOST FULL
Depth of Loose Water DCf1229
Figure 12-29. Diagram to illustrate pocketing of free surface.
The free surface effect of a given area of loose
water at a given angle of heel does NOT depend upon
the depth of the loose water in the tank or compartment, The reduction in free surface effect that results from
unless the loose water is shallow enough or deep pocketing is NOT taken into consideration when
enough to cause the effect known as “pocketing” of the evaluating stability. Since pocketing improves stability,
free surface. Pocketing occurs when the free surface of neglecting this factor in stability calculations provides a
the liquid comes in contact with the deck or the margin of safety; however, in centerline deep tanks on

12-16
some ships in which the tank is higher than wide, the As indicated by this formula, the free surface effect
opposite may be true. The normal practice of varies as the cube of the breadth (b) but only as the first
maintaining the fuel oil tanks 95 percent full takes power of the length (l). Because of this relationship, a
advantage of the fact that pocketing occurs, at very small single bulkhead that cuts a compartment in half in a
angles of heel, when a compartment is almost full. fore-and-aft direction will quarter the free surface
Length and Breadth of Free Surface effect.

The athwartship breadth of a compartment has a Chart for Calculating Free Surface Effect
great influence on the reduction in GM caused by the
free surface effect. This influence is shown by the To avoid having to make calculations from the
following formula: formula given in the previous section, a free surface
b 31 effect chart based on this formula is used to find the
Rise in G reduction in GM that occurs as a result of free surface.
12(35W)
Such a chart is shown in figure 12-30.
Where b = athwartship breadth of compartment
To use this chart, draw a straight line from the
1 = fore-and-aft length of compartment a p p r o p r i a t e p o i n t o n t h e AT H WA RT S H I P
W = displacement of ship DIMENSION scale (A) to the appropriate point on the

A C B D
CHART FOR 500
100 100
FREE SURFACE EFFECT
BASED ON EQUATION 600
90 90
b3 l 700
RISE IN G =
12 (35w)
80 80 800
b = BREADTH OF COMPARTMENT 900
I = LENGTH OF COMPARTMENT 1,000
70 w = DISPLACEMENT OF SHIP 70

60 E 60
1,500

10.0
50 2,000
LONGITUDINAL DIMENSION IN FEET

50
ATHWARTSHIP DIMENSION IN FEET

5.0
4.0
3.0
2.0 3,000
DISPLACEMENT IN TONS

40 40

1.0 4,000
.7
GM REDUCTION IN FEET

.5 5,000
30 .4 30
.3 6,000
PIVOT

.2 2 7,000
25 .1 25 8,000
9,000
10,000
.05
.04 1
20 .03 20
.02 15,000
.01
20,000
10 10

30,000

40,000

0 10 50,000

DCf1232
Figure 12-30. Chart for calculating free surface effect.

12-17
LONGITUDINAL DIMENSION scale (B); this line about the ship’s centerline, the ship will undergo
will intersect the pivot scale. Then draw a second parallel sinkage to a new waterline such as W1l1. Since
straight line from the point of intersection on the pivot the weight is off center, however, the ship assumes an
scale (C) to the appropriate point on the displacement inclined position with a waterline similar to W2L2.
scale (D). The point at which this second straight line
intersects the GM reduction scale (E) gives you the
reduction in GM (in feet) that is caused by the free
CL
L4
surface.
L3

For example, assume that you want to find what L2

reduction in GM is caused by free surface effect in a W1 L1

W b L
partially flooded compartment that is 35 feet athwart W2 a
ships and 20 feet fore-and-aft, in a ship of 10,000 tons W3

W4
displacement. Draw the first straight line from the
35-foot point on the athwartship dimension scale to the
20-foot point on the longitudinal dimension scale.
Then draw the second straight line from the point of DCf1231
intersection on the pivot line to the 10,000-ton point on
the displacement scale. The point at which the second
straight line intersects the GM reduction scale Figure 12-31. Free communication effect in off-center
compartment.
indicates how much reduction in GM has occurred
because of free surface effect in the partially flooded
compartment. In this example, GM has been reduced If the water in the compartment is now returned to
0.2 foot. its fluid state, it will have a waterline a-b that is parallel
to (but below) the ship’s waterline W2L2. Immediately,
Free Communication Effect however, additional water will flow in from the sea and
flood the compartment to the actual level of the ship’s
Thus far, the stability changes caused by the effect
waterline W2L2. The ship will therefore sink deeper in
of free surface and by the addition of the weight of the
the water and will assume a greater list; the waterline
flooding water have been considered. In certain
will reach a position such as W3L3. Again, additional
instances, it is also necessary to make allowance for
stability changes that occur when an off-center water will flow in from the sea and flood the
compartment is in free communication with the sea. compartment to the level of the ship’s waterline W3L3;
this will cause the ship to sink even deeper in the water
If a boundary of an off-center compartment is so and to assume an even greater list. These interactions
extensively ruptured that the sea can flow freely in
will continue until the waterline is at the position
and out as the ship rolls, the FREE
represented by W4L4.
COMMUNICATION EFFECT will cause a reduction
in GM and in GZ. Note that the free communication Note that stability is not usually reduced by free
effect on stability is IN ADDITION TO the effect of communication if the compartment is symmetrical
free surface and the effect of added weight. To a b o u t t h e s h i p ’s c e n t e r l i n e . U n d e r c e r t a i n
understand the free communication effect, consider circumstances, free communication in a centerline
an off-center compartment partially full of water and compartment may increase the free surface effect, and
in free communication with the sea, as shown in thereby reduce stability. However, it is important to
figure 12-31. (Note that this compartment is free to remember that this reduction in stability occurs from
vent at the top.)
the increased free surface effect, rather than from any
Before the hull is ruptured, the ship floats on an free communication effect.
even keel at waterline WL. Then the compartment is
partially flooded and left in free communication with Summary of Effects of Loose Water
the sea. Assume that the water enters the compartment
instantaneously (up to the level of the ship’s original The addition of loose water to a ship alters the
waterline WL) and is instantaneously frozen solid. If stability characteristics by means of three effects that
the weight of the frozen water is distributed equally must be considered separately: (1) the effect of added

12-18
 weight, (2) the effect of free surface, and (3) the effect When a ship has trim, however, neither the draft
of free communication. amidships nor the average of the forward and after
drafts will give a true mean draft. For most types of
Figure 12-32 shows the development of a stability
ships, the curves of form may be used without
curve with corrections for added weight, free surface,
correction for trim, PROVIDED the trim is less than
and free communication. Curve A is the ship’s original
about 1 percent of the length of the ship. When the trim
stability curve before flooding. Curve B represents the
is greater, however, the readings obtained from the
situation after flooding; this curve shows the effect of
curves of form must be corrected for trim.
added weight (increased stability) but it does NOT
show the effects of free surface or of free Longitudinal stability is the tendency of a ship to
communication. Curve C is curve B corrected for free resist a change in trim. The longitudinal metacentric
surface effect only. Curve D is curve B corrected for height multiplied by the displacement is taken as a
both free surface effect and free communication effect. measure of INITIAL longitudinal stability when trim
Curve D, therefore, is the final stability curve; it is very small. (It is important to note that the
incorporates corrections for all three effects of loose longitudinal metacenter (M1) is NOT the same as the
water. transverse metacenter.) A more accurate measure of
the ship’s ability to resist a change of trim is made in
terms of the moment required to produce a change in
4 trim of a definite amount. The MOMENT TO
CHANGE TRIM 1 INCH (MTI) is used as the standard
RIGHTING ARM IN FEET

3
measure of resistance to longitudinal inclination.
CURVE B
2
CURVE A
CURVE C REVIEW QUESTIONS
1 CURVE D

Q7. The ship’s center of gravity is the point at

0 10 20 30 40 50 60 70 80 90
ANGLE OF HEEL IN DEGREES
which all weights of the ship may be
DCf1232 considered to be concentrated. The force of
gravity is considered as acting straight
Figure 12-32. Development of stability curve corrected for downward, through the center of gravity, at
effects of added weight, free surface, and free communication. right angles to the waterline.
1. True
LONGITUDINAL STABILITY 2. False
Thus far in studying stability, you have been Q8. Detailed information concerning changes in
concerned only with TRANSVERSE STABILITY and the center of gravity of a ship can be obtained
with TRANSVERSE INCLINATIONS. LONGI- from which of the following NSTMs?
TUDINAL STABILITY and LONGITUDINAL 1. NSTM, chapter 096
I N C L I NAT I O N S , o r T R I M , s h o u l d a l s o b e
considered. 2. NSTM, chapter 040

Trim is measured by the difference between the 3. NSTM, chapter 033

forward draft and the after draft. When the after draft is 4. NSTM, chapter 010
greater than the forward draft, the ship is said to be
Q9. Which of the following terms is used to
TRIMMED BY THE STERN. When the forward draft
is greater than the after draft, the ship is said to be describe water or other liquid that has a free
TRIMMED BY THE BOW or TRIMMED BY THE surface?
HEAD. As a ship trims, it inclines about an athwartship 1. Reserve buoyancy
axis that passes through a point known as the CENTER
2. Reserve ballast
OF FLOTATION (CF).
3. Draft
The mean draft that is used to enter the draft scale
to read a displacement curve is the draft amidships. 4. Loose water

12-19
Q10. What effect does pocketing have on stability? SUMMARY
1. Improves stability
This chapter has introduced you to the terminology
2. Improves righting arms used for ship stability; the laws of physics and
3. Improves buoyancy trigonometry used to determine stability and buoyancy
of a ship; and the effects of buoyancy, gravity, and
4. Improves righting moments weight shifts on ship stability. Other aspects involved
Q11. Which of the following effects does NOT in the study of stability are taken into consideration
alter the stability characteristics of a ship when an inclining experiment is being conducted,
when you have loose water? when the ship is being dry docked, or when a
grounding has occurred.
1. Added weight
2. Free surface Aboard certain ships you may qualify as ballasting
3. Free communication officer and be actively involved in maintaining
stability. Remember that additional information on this
4. Added buoyancy topic may be found in the following publications:
Q12. What does longitudinal stability resist? Naval Ships’ Technical Manual (NSTM), chapter 079,
volume 1, and chapter 096; nonresident training
1. Change in trim
c o u r s e s ( N RT C s ) : M a t h e m a t i c s , vo l u m e 1 ;
2. Change in list Mathematics, volume 2A; Fireman; and Basic
3. Draft Machines.
4. Heeling

12-20
 REVIEW ANSWERS A7. The ship’s center of gravity, is the point at
which all weights of the ship may be
A1. Detailed information on the laws of considered to be concentrated. The force of
mathematics and physics used to determine gravity is considered as acting straight
the buoyancy and stability of a ship are downward, through the center of gravity, at
provided in Naval Ships’ Technical Manual right angles to the waterline. (1) True
(NSTM), chapter 079, volume 1, and in
A8. Detailed informationconcerning changes in
NSTM, chapter 096. (1) True
the center of gravity of a ship can be obtained
A2. Which of the following trigonometric from which of the following NSTMs?
functions is NOT used for making (1) NSTM, chapter 096
calculations to determine a ship’s stability?
A9. Which of the following terms is used to
(4) Cotangent
describe water or other liquid that has a free
A3. Which of the following terms best defines surface? (4) Loose water
force multiplied by the distance from an axis
A10. What effect does pocketing have on stability?
about which you want to find its effect?
(1) Improves stability
(1) Moment of force
A11. Which of the following effects does NOT
A4. The volume of water that is moved by the hull
alter the stability characteristics of a ship
of a ship is known as “displacement.”
when you have loose water? (4) Added
(1) True
Buoyancy
A5. What measurement is known by the term
A12. What does longitudinal stability resist?
freeboard? (2) Distance from the waterline
(1) Change in trim
to the weather deck edge
A6. Which of the following information is NOT
contained in the “booklet of inclining
experiment data?” (3) Reserve buoyancy

12-21