Free Standard provided by BIS via BSB Edge Private Limited to Schneider 

-
Chennai([email protected]) 165.225.104.124 [for non-commercial use only].
(Reaffirmed 2014) 

IS 8603 (Part  4) :2003

(Reaffirmed 2013) 
(Reaffirmed 2019)
 

(Reaffirmed 2012) 

(Reaffirmed 2011) 

Indian Standard  
DIMENSIONS FOR PORCELAIN TRANSFORMER
(Reaffirmed 2010) 
BUSHINGS FOR USE IN HEAVILY POLLUTED
 
ATMOSPHERES
(Reaffirmed 2009) 
PART 4 52 kV BUSHINGS
 

(Reaffirmed 2008) 
ICS 29.080.20:29.180
 

(Reaffirmed 2007) 

(Reaffirmed 2006) 

(Reaffirmed 2005) 

0 BIS 2003

BUREAU OF INDIAN STANDARDS

MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI 110002

October 2003 Price Group 1

 Free Standard provided by BIS via BSB Edge Private Limited to Schneider -
Chennai([email protected]) 165.225.104.124 [for non-commercial use only].

Electrical Insulators and Accessories Sectional Committee, ET 06

FOREWORD

“lb is Indian Standard (Part 4) was adopted by the Bureau of Indian Standards, after the draft finalized by the
Electrical Insulators and Accessories Sectional Committee had been approved by the Electrotechnical Division
Council.

l-his standard covers the dimensions of porcelain parts of the transformers bushings of 52 kV for use in heavily
polluted atmospheres

This standard is one of the series of four Indian Standards on dimensions for porcelain transformer bushings for
use in heavily polluted atmospheres. Other standards published in this series are as follows:

(Part 1):1977 12 kV and 17.5 kV bushings

(Part 2): 1977 24 kV bushings
(Part 3):1977 36 kV bushings

For the purpose of deciding whether a particular requirement of this standard is complied with Ihe final value,
observed or calculated, expressing the result of a test or analysis, shall be rounded off in accordance with
1S 2: 1960 ‘Rules for rounding off numerical values (revised,)’. The number of significant places retained in the
rounded off value should be the same as that of the specified value in this standard.
 Free Standard provided by BIS via BSB Edge Private Limited to Schneider -
Chennai([email protected]) 165.225.104.124 [for non-commercial use only].

IS 8603 (Part 4) :2003

Indian Standard
DIMENSIONS FOR PORCELAIN TRANSFORMER
BUSHINGS FOR USE IN HEAVILY POLLUTED
ATMOSPHERES
PART 4 52 kV BUSHINGS

1 SCOPE bushing for use in heavily polluted atmosphere is given

in Fig. 1.
This standard (Part 4) lays down the dimensions of the
porcelain parts of the transformer bushings of 52 kV 3.2 Unless specified otherwise, tolerance on dimension
for use in heavily polluted atmospheres. shall be:

2 REFERENCES a) + (0.04 d– 1.5)

where
The following standards are necessary adjuncts to this
standard: d=* 300 mm, and
[S No. Title b) + (0.025 d+ 6)
3347 (Part 8/ Dimensions for porcelain where
Sec 2): 1992 transformer bushings for use in
d= greater than 300 mm.
lightly polluted atmospheres: Part 8
52 kV Bushings, Section 2 Metal 3.3 The maximum limits for the camber, ovality,
parts eccentricity and tilt of shed of bushings shall as be as
5621:1980 Hollow insulators for use in per IS 5621.
electrical equipment (fhst revision)
4 METAL PARTS
3 DIMENSIONS
For metal parts for these bushings, reference shall be
3.1 The dimensions of porcelain parts for 1 000 A made to IS 3347(Part 8/See 2) .

1
 Free Standard provided by BIS via BSB Edge Private Limited to Schneider -
Chennai([email protected]) 165.225.104.124 [for non-commercial use only].

IS 8603 (Part 4):2003

v
u
r
2

E
E

.
 Free Standard provided by BIS via BSB Edge Private Limited to Schneider -
Chennai([email protected]) 165.225.104.124 [for non-commercial use only].

Bureau of Indian Standards

B IS is a statutory institution established under the Bureau of [ndian Mandards Act, 1986 to promote harmonious
development of the activities of standardization, marking and quality certification of goods and attending to
connected matters in the country.

Copyright

BI S has the copyright of all its publications. No part of these publications may be reproduced in any form
without the prior permission in writing of BIS. This does not preclude the free use, in the course of implementing
the standard, of necessary details, such as symbols and sizes, type or grade designations. Enquiries relating to
copyright be addressed to the Director (Publication), BIS.

Review of Indian Standards

Amendments are issued to standards as the need arises on the basis of comments. Standards are also reviewed
periodically; a standard along with amendments is reaffirmed when such review indicates that no changes are
needed; if the review indicates that changes are needed, it is taken up for revision. Users of Indian Standards
should ascertain that they are in possession of the latest amendments or edition by referring to the latest issue of
‘BIS CataIogue’ and’ Standards: Monthly Additions’..

This Indian Standard has been developed from Dot: No. ETD 06 (3995).

Amendments Issued Since Publication

Amend No. Date of Issue Text Affected

BUREAU OF INDIAN STANDARDS

Headquarters:
Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110002 Telegrams: Manaksanstha
Telephones: 23230131,23233375,2323 9402 (Common to all offices)
Regional Offices: Telephone
Central : Manak Bhavan, 9 Bahadur Shah Zafar Marg 23237617
NEW DELHI 110002 { 23233841

Eastern : 1/14 C.1.T. Scheme VII M, V.I.P. Road, Kankurgachi 23378499,23378561

KOLKATA 700054 { 23378626,23379120
Northern : SCO 335-336, Sector 34-A, CHANDIGARH 160022 603843
{ 609285
Southern : C.I.T. Campus, IV Cross Road, CHENNAI 600113 22541216,22541442
{ 22542519,22542315
Western : Manakalaya, E9 MIDC, Marol, Andheri (East) 28329295,28327858
MUMBAI 400093 { 28327891,28327892

Branches : AHMEDABAD. BANGALORE. BHOPAL. BHUBANESHWAR. COIMBATORE. FARIDABAD.

GHAZIABAD. GUWAHATI. HYDERABAD. JAIPUR. KANPUR. LUCKNOW. NAGPUR.
NALAGARH. PATNA. PUNE. RAJKOT. THIRUVANANTHAPURAM. VISAKHAPATNAM.

Printed at Simco Printing Press, Delhl