LM2900, LM3900

QUADRUPLE NORTON OPERATIONAL AMPLIFIERS

SLOS059 – JULY 1979 – REVISED SEPTEMBER 1990

D Wide Range of Supply Voltages, Single or N PACKAGE

Dual Supplies (TOP VIEW)

D Wide Bandwidth
1IN + VCC
D
1 14
Large Output Voltage Swing 2IN + 2 13 3IN +
D Output Short-Circuit Protection 2IN – 3 12 4IN +
D Internal Frequency Compensation 2OUT 4 11 4IN –
D Low Input Bias Current 1OUT 5 10 4OUT

D Designed to Be Interchangeable With

1IN –
GND
6
7
9
8
3OUT
3IN –
National Semiconductor LM2900 and
LM3900, Respectively

description
These devices consist of four independent, high- symbol (each amplifier)
gain frequency-compensated Norton operational
amplifiers that were designed specifically to
operate from a single supply over a wide range of
voltages. Operation from split supplies is also IN + +
possible. The low supply current drain is OUT
essentially independent of the magnitude of the IN – –
supply voltage. These devices provide wide band-
width and large output voltage swing.
The LM2900 is characterized for operation from
– 40°C to 85°C, and the LM3900 is characterized
for operation from 0°C to 70°C.

schematic (each amplifier)

VCC

Constant
Current 200 µA
Generator

OUT

IN –

IN + 1.3 mA

PRODUCTION DATA information is current as of publication date. Copyright  1990, Texas Instruments Incorporated
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1

LM2900, LM3900
QUADRUPLE NORTON OPERATIONAL AMPLIFIERS
SLOS059 – JULY 1979 – REVISED SEPTEMBER 1990

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
LM2900 LM3900 UNIT
Supply voltage, VCC (see Note 1) 36 36 V
Input current 20 20 mA
Duration of output short circuit (one amplifier) to ground at (or below) 25°C free-air temperature
unlimited unlimited
(see Note 2)
Continuous total dissipation See Dissipation Rating Table
Operating free-air temperature range – 40 to 85 0 to 70 °C
Storage temperature range – 65 to 150 – 65 to 150 °C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 260 260 °C
NOTES: 1. All voltage values, except differential voltages, are with respect to the network ground terminal.
2. Short circuits from outputs to VCC can cause excessive heating and eventual destruction.

DISSIPATION RATING TABLE

TA ≤ 25°C DERATING FACTOR TA = 70°C TA = 85°C
PACKAGE
POWER RATING ABOVE TA = 25°C POWER RATING POWER RATING
N 1150 mW 9.2 mW/°C 736 mW 598 mW

recommended operating conditions

LM2900 LM3900
UNIT
MIN MAX MIN MAX
Supply voltage, VCC (single supply) 4.5 32 4.5 32 V
Supply voltage, VCC + (dual supply) 2.2 16 2.2 16 V
Supply voltage, VCC – (dual supply) – 2.2 – 16 – 2.2 – 16 V
Input current (see Note 3) –1 –1 mA
Operating free-air temperature, TA – 40 85 0 70 °C
NOTE 3: Clamp transistors are included that prevent the input voltages from swinging below ground more than approximately – 0.3 V. The
negative input currents that may result from large signal overdrive with capacitive input coupling must be limited externally to values
of approximately – 1 mA. Negative input currents in excess of – 4 mA causes the output voltage to drop to a low voltage. These
values apply for any one of the input terminals. If more than one of the input terminals are simultaneously driven negative, maximum
currents are reduced. Common-mode current biasing can be used to prevent negative input voltages.

2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 LM2900, LM3900
QUADRUPLE NORTON OPERATIONAL AMPLIFIERS
SLOS059 – JULY 1979 – REVISED SEPTEMBER 1990

electrical characteristics, VCC = 15 V, TA = 25°C (unless otherwise noted)

LM2900 LM3900
PARAMETER TEST CONDITIONS† UNIT
MIN TYP MAX MIN TYP MAX
TA = 25°C 30 200 30 200
IIB Input bias current (inverting input) II + = 0 nA
TA = Full range 300 300

Mirror gain II+ = 20 µA to 200 µA 09

0.9 11
1.1 09
0.9 11
1.1 µA/µA
TA = Full range,
range
Change in mirror gain See Note 4 2% 5% 2% 5%
VI + = VI –, g ,
TA = Full range,
Mirror current 10 500 10 500 µA
See Note 4
Large-signal differential VO = 10 V, RL = 10 kΩ,
AVD 1.2 2.8 1.2 2.8 V/mV
voltage amplification f = 100 Hz
ri Input resistance (inverting input) 1 1 MΩ
ro Output resistance 8 8 kΩ
Unity-gain bandwidth (inverting
B1 2.5 2.5 MHz
input)
Supply voltage rejection ratio
kSVR 70 70 dB
(∆VCC /∆VIO)
RL = 2 kΩ 13.5 13.5
III+ = 0
0,
VOH High-level output voltage VCC = 30 V, V
II – = 0 29.5 29.5
No load
II + = 0, II – = 10 µA,
VOL Low-level output voltage 0.09 0.2 0.09 0.2 V
RL = 2 kΩ
Short-circuit output current II + = 0, II – = 0,
IOS –6 – 18 –6 – 10 mA
(output internally high) VO = 0
Pulldown current 0.5 1.3 0.5 1.3 mA
IOL Low-level output current‡ II – = 5 µA VOL = 1 V 5 5 mA
ICC Supply current (four amplifiers) No load 6.2 10 6.2 10 mA
† All characteristics are measured under open-loop conditions with zero common-mode voltage unless otherwise specified. Full range for TA is
– 40°C to 85°C for LM2900 and 0°C to 70°C for LM3900.
‡ The output current-sink capability can be increased for large-signal conditions by overdriving the inverting input.
NOTE 4: These parameters are measured with the output balanced midway between VCC and GND.

operating characteristics, VCC± = ±15 V, TA = 25°C

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Low-to-high output 0.5
SR Slew rate at unity gain VO = 10 V,
V CL = 100 pF,
pF RL = 2 kΩ V/µs
High-to-low output 20

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3

LM2900, LM3900
QUADRUPLE NORTON OPERATIONAL AMPLIFIERS
SLOS059 – JULY 1979 – REVISED SEPTEMBER 1990

TYPICAL CHARACTERISTICS†

INPUT BIAS CURRENT (INVERTING INPUT) MIRROR GAIN

vs vs
FREE-AIR TEMPERATURE FREE-AIR TEMPERATURE
80 1.2
VCC = 15 V VCC = 15 V
70 VO = 7.5 V 1.15 II + = 10 µA
II + = 0
1.1
IIB – Input Bias Current – nA

60

II – /I + – Mirror Gain
50 1.05

40 1

30 0.95

20 0.9

10 0.85

0 0.8
– 75 – 50 – 25 0 25 50 75 100 – 75 – 50 – 25 0 25 50 75 100 125
TA – Free-Air Temperature – °C TA – Free-Air Temperature – °C

Figure 1 Figure 2

LARGE SIGNAL LARGE SIGNAL

DIFFERENTIAL VOLTAGE AMPLIFICATION DIFFERENTIAL VOLTAGE AMPLIFICATION
vs vs
FREQUENCY SUPPLY VOLTAGE
104 104
RL ≥ 10 kΩ VCC = 15 V
TA = 25°C
AVD – Differential Voltage Amplification
AVD – Differential Voltage Amplification

103 103
RL = 2 kΩ

102 102

10 10
RL = 10 kΩ
TA = 25°C

1 1
100 1k 10 k 100 k 1M 10 M 0 5 10 15 20 25 30

f – Frequency – Hz VCC – Supply Voltage – V

Figure 3 Figure 4

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 LM2900, LM3900
QUADRUPLE NORTON OPERATIONAL AMPLIFIERS
SLOS059 – JULY 1979 – REVISED SEPTEMBER 1990

TYPICAL CHARACTERISTICS†

LARGE SIGNAL
DIFFERENTIAL VOLTAGE AMPLIFICATION SUPPLY VOLTAGE REJECTION RATIO
vs vs
FREE-AIR TEMPERATURE FREQUENCY
104 100

KSVR – Supply Voltage Rejection Ratio – dB

VCC = 15 V
90
TA = 25°C
AVD – Differential Voltage Amplification

80
103
70

60

102 50

40

30
10
20
VCC = 15 V
VO = 10 V 10
RL = 10 kΩ
1 0
– 75 – 50 – 25 0 25 50 75 100 125 100 400 1 k 4k 10 k 40 k 100 k 400 k 1 M
TA – Free-Air Temperature – °C f – Frequency – Hz

Figure 5 Figure 6

SHORT-CIRCUIT OUTPUT CURRENT

PEAK-TO-PEAK OUTPUT VOLTAGE (OUTPUT INTERNALLY HIGH)
vs vs
FREQUENCY SUPPLY VOLTAGE
16 30
VCC = 15 V
VO(PP) – Peak-To-Peak Output Voltage – V

VO = 0
IOS – Short-Circuit Output Current – mA

14 RL = 2 kΩ II + = 0
II + = 0 25
II – = 0
12 TA = 25°C
TA = 0°C
20
10
TA = 25°C
8 15

ÁÁ
10

ÁÁ
4

ÁÁ
5
2

0 0
1k 10 k 100 k 1M 10 M 0 5 10 15 20 25 30
f – Frequency – Hz VCC – Supply Voltage – V

Figure 7 Figure 8
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5

LM2900, LM3900
QUADRUPLE NORTON OPERATIONAL AMPLIFIERS
SLOS059 – JULY 1979 – REVISED SEPTEMBER 1990

TYPICAL CHARACTERISTICS†

LOW-LEVEL OUTPUT CURRENT PULLDOWN CURRENT

vs vs
SUPPLY VOLTAGE SUPPLY VOLTAGE
60 2

VOL = 1 V 1.8
IOL– Low-Level Output Current – mA

50 II + = 0
TA = 25°C 1.6 TA = – 40°C

Pulldown Current – mA
1.4
40 II – = 100 µA
1.2 TA = 25°C

30 1
TA = 85°C
0.8
20
0.6
II – = 10 µA
0.4
10
II – = 5 µA 0.2

0 0
0 5 10 15 20 25 30 0 5 10 15 20 25 30
VCC – Supply Voltage – V VCC – Supply Voltage – V

Figure 9 Figure 10

PULLDOWN CURRENT TOTAL SUPPLY CURRENT

vs vs
FREE-AIR TEMPERATURE SUPPLY VOLTAGE
2 8
VCC = 15 V
1.8 7
1.6
I CC – Total Supply Current – mA

6
Pulldown Current – mA

1.4
5
1.2

1 4

0.8 3
0.6
2
0.4 TA = 25°C
1 No Signal
0.2 No Load

0 0
– 75 – 50 – 25 0 25 50 75 100 125 0 5 10 15 20 25 30
TA – Free-Air Temperature –°C VCC – Supply Voltage – V
Figure 11 Figure 12

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 LM2900, LM3900
QUADRUPLE NORTON OPERATIONAL AMPLIFIERS
SLOS059 – JULY 1979 – REVISED SEPTEMBER 1990

APPLICATION INFORMATION

Norton (or current-differencing) amplifiers can be used in most standard general-purpose operational amplifier
applications. Performance as a dc amplifier in a single-power-supply mode is not as precise as a standard
integrated-circuit operational amplifier operating from dual supplies. Operation of the amplifier can best be
understood by noting that input currents are differenced at the inverting input terminal and this current then flows
through the external feedback resistor to produce the output voltage. Common-mode current biasing is generally
useful to allow operating with signal levels near (or even below) ground.
Internal transistors clamp negative input voltages at approximately – 0.3 V but the magnitude of current flow has to
be limited by the external input network. For operation at high temperature, this limit should be approximately
– 100 µA.
Noise immunity of a Norton amplifier is less than that of standard bipolar amplifiers. Circuit layout is more critical since
coupling from the output to the noninverting input can cause oscillations. Care must also be exercised when driving
either input from a low-impedance source. A limiting resistor should be placed in series with the input lead to limit the
peak input current. Current up to 20 mA will not damage the device, but the current mirror on the noninverting input
will saturate and cause a loss of mirror gain at higher current levels, especially at high operating temperatures.
V+
1 MΩ

10 kΩ 1 kΩ
1 MΩ

1 MΩ
Input –
30 kΩ
100 kΩ
+ Output
91 kΩ

IO ≈ 1 mA per input volt

Figure 13. Voltage-Controlled Current Source

V+

1 MΩ 1 MΩ

– Output

100 kΩ
Input +

100 kΩ

1 kΩ

IO ≈ 1 mA per input volt

Figure 14. Voltage-Controlled Current Sink

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7

 PACKAGE OPTION ADDENDUM

www.ti.com 10-Jun-2014

PACKAGING INFORMATION

Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)

LM2900D ACTIVE SOIC D 14 50 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 85 LM2900

& no Sb/Br)
LM2900DR ACTIVE SOIC D 14 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 85 LM2900
& no Sb/Br)
LM2900DR ACTIVE SOIC D 14 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 85 LM2900
& no Sb/Br)
LM2900DR ACTIVE SOIC D 14 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 85 LM2900
& no Sb/Br)
LM2900N ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type -40 to 85 LM2900N
(RoHS)
LM2900N ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type -40 to 85 LM2900N
(RoHS)
LM2900N ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type -40 to 85 LM2900N
(RoHS)
LM2900NE4 ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type -40 to 85 LM2900N
(RoHS)
LM2900NE4 ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type -40 to 85 LM2900N
(RoHS)
LM2900NE4 ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type -40 to 85 LM2900N
(RoHS)
LM3900D ACTIVE SOIC D 14 50 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM3900
& no Sb/Br)
LM3900D ACTIVE SOIC D 14 50 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM3900
& no Sb/Br)
LM3900D ACTIVE SOIC D 14 50 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM3900
& no Sb/Br)
LM3900DG4 ACTIVE SOIC D 14 50 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM3900
& no Sb/Br)
LM3900DG4 ACTIVE SOIC D 14 50 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM3900
& no Sb/Br)
LM3900DG4 ACTIVE SOIC D 14 50 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM3900
& no Sb/Br)
LM3900DR ACTIVE SOIC D 14 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM3900
& no Sb/Br)

Addendum-Page 1
 PACKAGE OPTION ADDENDUM

www.ti.com 10-Jun-2014

Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)

LM3900DR ACTIVE SOIC D 14 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM3900

& no Sb/Br)
LM3900DR ACTIVE SOIC D 14 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM3900
& no Sb/Br)
LM3900N ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type 0 to 70 LM3900N
(RoHS)
LM3900N ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type 0 to 70 LM3900N
(RoHS)
LM3900N ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type 0 to 70 LM3900N
(RoHS)
LM3900NE4 ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type 0 to 70 LM3900N
(RoHS)
LM3900NE4 ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type 0 to 70 LM3900N
(RoHS)
LM3900NE4 ACTIVE PDIP N 14 25 Pb-Free CU NIPDAU N / A for Pkg Type 0 to 70 LM3900N
(RoHS)

(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.

(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)

(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

Addendum-Page 2
 PACKAGE OPTION ADDENDUM

www.ti.com 10-Jun-2014

(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.

(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

Addendum-Page 3
 PACKAGE MATERIALS INFORMATION

www.ti.com 14-Jul-2012

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1
Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM2900DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
LM3900DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1

Pack Materials-Page 1
 PACKAGE MATERIALS INFORMATION

www.ti.com 14-Jul-2012

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM2900DR SOIC D 14 2500 367.0 367.0 38.0
LM3900DR SOIC D 14 2500 367.0 367.0 38.0

Pack Materials-Page 2
 IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated