AAC Block Adhesive

Polymer based thin-set adhesive for laying and

construction with AAC Blocks and other light
weight masonry units

Substrates

• AAC Blocks
Features / Benefits
• Cement Mortar Blocks/Bricks
• Concrete hollow blocks
• Improved bond strength • Light weight masonry blocks
• No curing required after block work is done • Cellular concrete blocks
• Flexible, shock & impact resistant • Fly Ash Bricks
• Optimum compressive & splitting tensile strength • Calcium silicate bricks
• Easy to use • Clay Bricks
• Long working time
• Fast & economical

Certification

Application IS 2250 ASTM C 1660, C

2250 & C 270
For interior and exterior use for construction with thin bed
mortar for AAC, ALC and cellular concrete blocks.
Application

ANSI A 118.1

MYKL-TDS- AAC – REV 01; 04/18

 ASTM C 270 Data
TECHNICAL DATA
Property : Test Requirement Typical Values
method
Performance Properties: Compressive Strength Minimum 750 psi
850-950 psi
: ASTM C109 (5.2Mpa)
AAC Block Adhesive mixed with Water
Water Retention:
Minimum 75% 85%-90%
ASTM C1506
Applicable Standards: Air Content : ASTM
ANSI A 118.1T, ASTM C 1660, ASTM C 270, IS Maximum 14% 10%-12%
C91
2250 & EN 12004 / ISO13007 (Class C1T)
The Adhesive mortar conforms to ASTM C 270
ANSI Data
Property : Test Requirement Typical Values ASTM C 2250 Data
method Property: Test Requirement Typical Values
Open Time (20 Method
Minutes at 28 Compressive
≥75 psi 95 psi – 100 psi 5.0-7.5 MPa 5.5 – 6.5 MPa
days): ANSI Strength: Appendix A
(0.50 Mpa) (0.65 – 0.69 Mpa) Consistency:
A118.1 Clause – 130-150 mm 135-145 mm
5.3 Appendix B
Sag: ANSI A118.1- ≤0.02 Water Retention:
0.016 – 0.018 Inches Minimum 70% 85%-90%
Clause 6.0 Inches (0.50 Appendix C
(0.40-0.45 mm) The adhesive mortar conforms to ASTM C 2250
mm)
Glazed wall tile Shear Strength Specifications subject to change without notification.
7 Days: ANSI Results shown are typical but reflect test procedures used.
>200psi 200-225 psi
A118.1 – Clause Actual field performance will depend on installation
(1.38Mpa) (1.38 Mpa-1.55 Mpa)
7.1.2
7 Days Water methods and site conditions.
immersion: ANSI >150psi 150-175 psi
A118.1- Clause (1.03Mpa) (1.03 Mpa-1.20 Mpa) Packaging:
7.1.3)
Porcelain Mosaic Tile Shear Strength 20 kg & 50 kg bags
1 Day: ANSI
>50psi 50 -75 psi Colour:
A118.1 – Clause
(0.34Mpa) (0.34 Mpa-0.51 Mpa) Grey
7.2.2
7 Days: ANSI
>150psi 150-175 psi Coverage:
A118.1 – Clause
(1.03Mpa) (1.03 Mpa-1.20 Mpa)
7.2.3 The following is the coverage table for wall area in Square feet
7 Days Water that can be constructed using AAC Blocks of size 600mm X
immersion: ANSI >100psi 125-150 psi 200mm X 100mm
A118.1 – Clause (0.69Mpa) (0.86 Mpa-1.03 Mpa)
7.2.4 Thickness Coverage for
Mortar Bed Thickness Coverage for 50 Kg
28 Days: ANSI 20
>150psi 150-175 psi bag
A118.1 – Clause Kg Bag
(1.03Mpa) (1.03 Mpa-1.20 Mpa)
7.2.5 2 mm 300 Sft 120 Sft
12 Weeks: ANSI 3 mm 200 Sft 80
>150psi 150-175 psi
A118.1 – Clause 4 mm 150 Sft Sft
60
(1.03Mpa) (1.03 Mpa-1.20 Mpa)
7.2.6 Sft
The adhesive mortar conforms to ANSI A 118.1T Coverage is based on smoothness and evenness of the
substrate, size of blocks used and the thickness of mortar used.
ASTM C 1660 Data A general guide line for coverage of mortar is given when used
Property: Test Requirement Typical Values with 30% Water is added to powder.
Method
Splitting Tensile 58 -71 psi
Strength: Test Method (0.40 – 0.49 50 – 70 psi Working Properties at 70° F (21° C)
ASTM C1660 MPa) AAC Block Adhesive mixed with Water

The adhesive mortar conforms to ASTM C 1660 Adjustability time 20 minutes

Pot Life 2 Hours

MYKL-TDS- AAC – REV 01; 04/18

 INSTALLATION CUSTOMER CARE
MYK LATICRETE India Pvt Ltd.
Surface Preparation:
All surfaces should be between 40 F (4 C) and 90 F 8-2-703/A, Fourth Floor, Leela Gopal Towers,
(32 C) and structurally sound, clean and free of all dirt, oil, Road No-12, Banjara Hills, Hyderabad – 500034
grease, concrete sealers or curing compounds. Rough or
uneven concrete surfaces should be made smooth with MYK (T.S) Tel: +91-40-30413100
LATICRETE Latex Portland Cement underlayment to Customer Care: [email protected]
provide a wood float (or better) finish. Installation may be
made on a damp surface. Website: www.myklaticrete.com

All slabs must be plumb and true to within ¼” (6mm) in 10 ft

(3m).
Follow ANSI Specification AN-3.8 “Requirements for
Expansion Joints” or TCA Detail EJ171 “Expansion Joints”.
Do not cover expansion joints with mortar.
NOTE: In order to realize all the product advantages, for high
quality construction and best performance, it is necessary to
follow the AAC Block Manufacturer’s instructions or IS 6041
or other relevant codes and good practices.

Mixing:
Use approx. 50kg of AAC Block Adhesive thin bed mortar
with Approx. 15 ltrs of potable water. Take water in the
container and slowly add the powder into the water while
mixing by hand or slow speed mixing machine. Mix for 3 to 5
minutes till a smooth thixotropic mix without lumps is
obtained.

APPLICATION:

1) Thin bed mortar for laying blocks:

Before placing mortar, ensure the block work to be dry and
surfaces cleaned properly. Place the mixed mortar on the
block work in thin layers of 2 to 3 mm (or as required by
engineers at site) using trowel and place the next layer of
blocks on the mortar. Keep joints between the blocks as
required by the site engineers and fill the joints with the
mixed mortar, using a trowel. Check the plumb of the wall
while laying the blocks to keep the walls perfectly vertical to
the plumb.

2) As Adhesive to install tiles:

AAC Block Adhesive can be used as a thin-set adhesive to
install tiles/stones on masonry walls. Use a suitable notch
trowel to achieve desired thickness of adhesive for installation
of tiles /stones on the wall.

Plaster:
Plumb, square and true concrete block wall can be finished
with the applications of Special polymer plaster from MYK
Laticrete.
Plasters made with site mix may slump and powder due to
water absorption of the block work.

Cleaning:
Clean tools and containers with water while mortar is fresh.

MYKL-TDS- AAC – REV 01; 04/18