www.DataSheet4U.

com

www.fairchildsemi.com

FSDH321, FSDL321
Green Mode Fairchild Power Switch (FPSTM)

Features
OUTPUT POWER TABLE
• Internal Avalanche Rugged Sense FET
• Consumes only 0.65W at 240VAC & 0.3W load with 230VAC ±15%(3) 85-265VAC
Advanced Burst-Mode Operation PRODUCT Adapt- Open Adapt- Open
• Frequency Modulation for EMI Reduction er(1) Frame(2) er(1) Frame(2)
• Precision Fixed Operating Frequency FSDL321 11W 17W 8W 12W
• Internal Start-up Circuit
FSDH321 11W 17W 8W 12W
• Pulse-by-Pulse Current Limiting
• Abnormal Over Current Protection (AOCP) FSDL0165RN 13W 23W 11W 17W
• Over Voltage Protection (OVP) FSDM0265RN 16W 27W 13W 20W
• Over Load Protection (OLP) FSDH0265RN 16W 27W 13W 20W
• Internal Thermal Shutdown Function (TSD)
FSDL0365RN 19W 30W 16W 24W
• Auto-Restart Mode
• Under Voltage Lockout (UVLO) FSDM0365RN 19W 30W 16W 24W
• Low Operating Current (max 3mA) FSDL321L 11W 17W 8W 12W
• Adjustable Peak Current Limit FSDH321L 11W 17W 8W 12W
• Built-in Soft Start
FSDL0165RL 13W 23W 11W 17W
FSDM0265RL 16W 27W 13W 20W
Applications
FSDH0265RL 16W 27W 13W 20W
• SMPS for STB, Low cost DVD Player
FSDL0365RL 19W 30W 16W 24W
• Auxiliary Power for PC
• Adapter & Charger FSDM0365RL 19W 30W 16W 24W

Notes:
Related Application Notes 1. Typical continuous power in a non-ventilated enclosed
adapter with sufficient drain pattern as a heat sinker, at
• AN-4137, 4141, 4147(Flyback) / AN-4134(Forward)
50°C ambient.
2. Maximum practical continuous power in an open frame
Description design with sufficient drain pattern as a heat sinker, at 50°C
ambient.
Each product in the FSDx321 (x for H, L) family consists of
3. 230 VAC or 100/115 VAC with doubler.
an integrated Pulse Width Modulator (PWM) and Sense
FET, and is specifically designed for high performance off-
line Switch Mode Power Supplies (SMPS) with minimal Typical Circuit
external components. Both devices are integrated high volt-
age power switching regulators which combine an avalanche
rugged Sense FET with a current mode PWM control block.
The integrated PWM controller features include: a fixed AC
IN
oscillator with frequency modulation for reduced EMI, DC
OUT
Under Voltage Lock Out (UVLO) protection, Leading Edge
Blanking (LEB), an optimized gate turn-on/turn-off driver,
Thermal Shut Down (TSD) protection, Abnormal Over Cur- Vstr Drain

rent Protection (AOCP) and temperature compensated preci- Ipk

PWM
sion current sources for loop compensation and fault
protection circuitry. When compared to a discrete MOSFET Vfb Vcc Source

and controller or RCC switching converter solution, the

FSDx321 devices reduce total component count, design size,
weight while increasing efficiency, productivity and system
reliability. Both devices provide a basic platform that is well
suited for the design of cost-effective flyback converters. Figure 1. Typical Flyback Application

FPSTM is a trademark of Fairchild Semiconductor Corporation. Rev.1.0.5

©2005 Fairchild Semiconductor Corporation
www.DataSheet4U.com

FSDH321, FSDL321

Internal Block Diagram

Vcc Vstr Drain

2 5 6,7,8

+ ICH
V BURH -
8V/12V
Vcc good Internal
Vcc Vref
Freq.
Bias
V BURL /V BURH
Modulation
IBUR(pk)
Vcc Vcc
OSC
IDELAY I FB
Vfb Normal S Q
3 PWM
Gate
2.5R Burst R Q
driver
Ipk R
4 Soft
Start LEB

V SD

Vcc 1 GND
S Q

Vovp
Vcc good R Q
AOCP
TSD Vocp

Figure 2. Functional Block Diagram of FSDx321

2
www.DataSheet4U.com

FSDH321, FSDL321

Pin Definitions

Pin Number Pin Name Pin Function Description

1 GND Sense FET source terminal on primary side and internal control ground.
Positive supply voltage input. Although connected to an auxiliary transform-
er winding, current is supplied from pin 5 (Vstr) via an internal switch during
2 Vcc startup (see Internal Block Diagram section). It is not until Vcc reaches the
UVLO upper threshold (12V) that the internal start-up switch opens and de-
vice power is supplied via the auxiliary transformer winding.
The feedback voltage pin is the non-inverting input to the PWM comparator.
It has a 0.9mA current source connected internally while a capacitor and op-
tocoupler are typically connected externally. A feedback voltage of 6V trig-
3 Vfb gers over load protection (OLP). There is a time delay while charging
external capacitor Cfb from 3V to 6V using an internal 5uA current source.
This time delay prevents false triggering under transient conditions, but still
allows the protection mechanism to operate under true overload conditions.
This pin adjusts the peak current limit of the Sense FET. The feedback
0.9mA current source is diverted to the parallel combination of an internal
4 Ipk 2.8kΩ resistor and any external resistor to GND on this pin to determine the
peak current limit. If this pin is tied to Vcc or left floating, the typical peak cur-
rent limit will be 0.7A.
This pin connects directly to the rectified AC line voltage source. At start up
the internal switch supplies internal bias and charges an external storage
5 Vstr
capacitor placed between the Vcc pin and ground. Once the Vcc reaches
12V, the internal switch is opened.
The drain pins are designed to connect directly to the primary lead of the
transformer and are capable of switching a maximum of 650V. Minimizing
6, 7, 8 Drain
the length of the trace connecting these pins to the transformer will decrease
leakage inductance.

Pin Configuration

8DIP
8LSOP

GND 1 8 Drain
Vcc 2 7 Drain
Vfb 3 6 Drain
Ipk 4 5 Vstr

Figure 3. Pin Configuration (Top View)

3
www.DataSheet4U.com

FSDH321, FSDL321

Absolute Maximum Ratings

(Ta=25°C, unless otherwise specified)

Characteristic Symbol Value Unit

Drain Pin Voltage VDRAIN 650 V
Vstr Pin Voltage VSTR 650 V
Drain-Gate Voltage VDG 650 V
Gate-Source Voltage VGS ± 20 V
Drain Current Pulsed(1) IDM 1.5 A
Continuous Drain Current (Tc=25℃) ID 0.7 A
Continuous Drain Current (Tc=100℃) ID 0.32 A
(2)
Single Pulsed Avalanche Energy EAS 10 mJ
Supply Voltage VCC 20 V
Feedback Voltage Range VFB -0.3 to VCC V
Total Power Dissipation PD 1.40 W
Operating Junction Temperature TJ Internally limited °C
Operating Ambient Temperature TA -25 to +85 °C
Storage Temperature TSTG -55 to +150 °C

Note:
1. Repetitive rating: Pulse width is limited by maximum junction temperature
2. L = 24mH, starting Tj = 25°C

Thermal Impedance
(Ta=25°C, unless otherwise specified)

Parameter Symbol Value Unit

8DIP
Junction-to-Ambient Thermal(1) θJA 88.84 °C/W
Junction-to-Case Thermal(2) θJC 13.94 °C/W

Note:
1. Free standing with no heatsink; Without copper clad.
/ Measurement Condition : Just before junction temperature TJ enters into OTP.
2. Measured on the DRAIN pin close to plastic interface.

- all items are tested with the standards JESD 51-2 and 51-10 (DIP).

4
www.DataSheet4U.com

FSDH321, FSDL321

Electrical Characteristics
(Ta = 25°C unless otherwise specified)

Parameter Symbol Condition Min. Typ. Max. Unit

SENSE FET SECTION
VDS=650V, VGS=0V - - 25
Zero-Gate-Voltage Drain Current IDSS µA
VDS=520V, VGS=0V, TC=125°C - - 200
Drain-Source On-State Resistance RDS(ON) VGS=10V, ID=0.5A - 14 19 Ω
Forward Trans-Conductance(1) gfs VDS=50V, ID=0.5A 1.0 1.3 - S
Input Capacitance CISS - 162 -
VGS=0V, VDS=25V,
Output Capacitance COSS - 18 - pF
f=1MHz
Reverse Transfer Capacitance CRSS - 3.8 -
Turn-On Delay Time td(on) - 9.5 -
Rise Time tr - 19 -
VDS=325V, ID=1.0A ns
Turn-Off Delay Time td(off) - 33 -
Fall Time tf - 42 -
Total Gate Charge Qg - 7.0 -
VGS=10V, ID=1.0A,
Gate-Source Charge Qgs - 3.1 - nC
VDS=325V
Gate-Drain (Miller) Charge Qgd - 0.4 -
CONTROL SECTION
Switching Frequency fOSC 90 100 110 KHz
FSDH321
Switching Frequency Modulation ∆fMOD ±2.5 ±3.0 ±3.5 KHz
Switching Frequency fOSC 45 50 55 KHz
FSDL321
Switching Frequency Modulation ∆fMOD ±1.0 ±1.5 ±2.0 KHz
Switching Frequency Variation(2) ∆fOSC -25°C ≤ Ta ≤ 85°C - ±5 ±10 %
FSDH321 62 67 72 %
Maximum Duty Cycle DMAX
FSDL321 71 77 83 %
VSTART VFB=GND 11 12 13 V
UVLO Threshold Voltage
VSTOP VFB=GND 7 8 9 V
Feedback Source Current IFB VFB=GND 0.7 0.9 1.1 mA
Internal Soft Start Time tS/S VFB=4V 10 15 20 ms
BURST MODE SECTION
VBURH 0.4 0.5 0.6 V
Tj=25°C
Burst Mode Voltage VBURL 0.25 0.35 0.45 V
VBUR(HYS) Hysteresis - 150 - mV
PROTECTION SECTION
Peak Current Limit ILIM Tj=25°C, ∆i/∆t=250mA/us 0.60 0.70 0.80 A
Current Limit Delay Time(3) tCLD Tj=25°C - 600 - ns
Thermal Shutdown Temperature(3) TSD 125 145 - °C
Shutdown Feedback Voltage VSD 5.5 6.0 6.5 V
Over Voltage Protection VOVP 18 19 20 V
Shutdown Delay Current IDELAY VFB=4V 3.5 5.0 6.5 µA
Leading Edge Blanking Time tLEB 200 - - ns
TOTAL DEVICE SECTION
Operating Supply Current (control part only) IOP VCC=14V, VFB=0V 1 3 5 mA
Start-Up Charging Current ICH VCC=0V 0.7 0.85 1.0 mA
Vstr Supply Voltage VSTR VCC=0V 35 - - V

Note:
1. Pulse test: Pulse width ≤ 300us, duty ≤ 2%
2. These parameters, although guaranteed, are tested in EDS (wafer test) process
3. These parameters, although guaranteed, are not 100% tested in production

5
www.DataSheet4U.com

FSDH321, FSDL321

Comparison Between FSDM311 and FSDx321

Function FSDM311 FSDx321 FSDx321 Advantages

Soft-Start 15ms 15ms (same for both devices)
• Gradually increasing current limit
during soft-start further reduces peak
current and voltage stresses
• Eliminates external components used
for soft-start in most applications
• Reduces or eliminates output
overshoot
External Current Limit not applicable Programmable of • Smaller transformer
default current limit • Allows power limiting (constant over-
load power)
• Allows use of larger device for lower
losses and higher efficiency.
Frequency Modulation not applicable ±3.0KHz @100KHz • Reduces conducted EMI
±1.5KHz @50KHz
Burst Mode Operation Built into controller Built into controller (same for both devices)
• Improves light load efficiency
• Reduces power consumption at no-
load
• Transformer audible noise reduction
Drain Creepage at 7.62mm 7.62mm (same for both devices)
Package • Greater immunity to arcing provoked
by dust, debris and other contami-
nants

6
www.DataSheet4U.com

FSDH321, FSDL321

Typical Performance Characteristics (Control Part)

(These characteristic graphs are normalized at Ta = 25°C)

1.20 1.20
1.00 1.00

Normalized
0.80
Normalized

0.80
0.60 0.60
0.40 0.40
0.20 0.20
0.00 0.00
-50 0 50 100 150 -50 0 50 100 150

T emp[ ℃] T emp[℃]

Operating Frequency (Fosc) vs. Ta Frequency Modulation (∆FMOD) vs. Ta

1.20 1.20
1.00 1.00
0.80
Normalized
Normalized

0.80
0.60 0.60
0.40 0.40
0.20 0.20
0.00 0.00
-50 0 50 100 150 -50 0 50 100 150
T emp[℃] T emp[ ℃]

Maximum Duty Cycle (DMAX) vs. Ta Operating Supply Current (IOP) vs. Ta

1.20 1.20
1.00 1.00
0.80
Normalized
Normalized

0.80
0.60 0.60
0.40 0.40
0.20 0.20
0.00 0.00
-50 0 50 100 150 -50 0 50 100 150
T emp[℃] T emp[℃]

Start Threshold Voltage (VSTART) vs. Ta Stop Threshold Voltage (VSTOP) vs. Ta

7
www.DataSheet4U.com

FSDH321, FSDL321

Typical Performance Characteristics (Continued)

1.20 1.20
1.00 1.00
0.80
Normalized

Normalized
0.80
0.60 0.60
0.40 0.40
0.20 0.20
0.00 0.00
-50 0 50 100 150 -50 0 50 100 150
T emp[℃] T emp[℃]

Feedback Source Current (IFB) vs. Ta Start Up Charging Current (ICH) vs. Ta

1.20 1.20
1.00 1.00
0.80
Normalized
Normalized

0.80
0.60 0.60
0.40 0.40
0.20 0.20
0.00 0.00
-50 0 50 100 150 -50 0 50 100 150
T emp[℃] T emp[ ℃]

Peak Current Limit (ILIM) vs. Ta Burst Peak Current (IBUR(pk)) vs. Ta

1.20
1.00
Normalized

0.80
0.60
0.40
0.20
0.00
-50 0 50 100 150
T emp[℃]

Over Voltage Protection (VOVP) vs. Ta

8
www.DataSheet4U.com

FSDH321, FSDL321

Functional Description
3. Leading Edge Blanking (LEB) : At the instant the inter-
nal Sense FET is turned on, the primary side capacitance and
1. Startup : In previous generations of Fairchild Power secondary side rectifier diode reverse recovery typically
Switches (FPSTM) the Vstr pin had an external resistor to the cause a high current spike through the Sense FET. Excessive
DC input voltage line. In this generation the startup resistor voltage across the Rsense resistor leads to incorrect feedback
is replaced by an internal high voltage current source and a operation in the current mode PWM control. To counter this
switch that shuts off when 15ms goes by after the supply effect, the FPS employs a leading edge blanking (LEB) cir-
voltage, Vcc, gets above 12V. The source turns back on if cuit. This circuit inhibits the PWM comparator for a short
Vcc drops below 8V. time (tLEB) after the Sense FET is turned on.

Vin,dc
ISTR 4. Protection Circuits : The FPS has several protective
functions such as over load protection (OLP), over voltage
protection (OVP), abnormal over current protection
Vstr
(AOCP), under voltage lock out (UVLO) and thermal shut-
Vcc Vcc<8V
down (TSD). Because these protection circuits are fully inte-
UVLO on
J-FET grated inside the IC without external components, the
15ms after ICH
Vcc≥12V reliability is improved without increasing cost. Once a fault
UVLO off condition occurs, switching is terminated and the Sense FET
remains off. This causes Vcc to fall. When Vcc reaches the
UVLO stop voltage VSTOP (8V), the protection is reset and
the internal high voltage current source charges the Vcc
capacitor via the Vstr pin. When Vcc reaches the UVLO
Figure 4. High Voltage Current Source start voltage VSTART (12V), the FPS resumes its normal
operation. In this manner, the auto-restart can alternately
enable and disable the switching of the power Sense FET
until the fault condition is eliminated.
2. Feedback Control : The FSDx321 employs current mode
control, as shown in Figure 5. An opto-coupler (such as the
H11A817A) and shunt regulator (such as the KA431) are
typically used to implement the feedback network. Compar- 4.1 Over Load Protection (OLP) : Overload is defined as
ing the feedback voltage with the voltage across the Rsense the load current exceeding a pre-set level due to an unex-
resistor plus an offset voltage makes it possible to control the pected event. In this situation, the protection circuit should
switching duty cycle. When the KA431 reference pin volt- be activated in order to protect the SMPS. However, even
age exceeds the internal reference voltage of 2.5V, the opto- when the SMPS is operating normally, the over load protec-
coupler LED current increases, the feedback voltage Vfb is tion (OLP) circuit can be activated during the load transition.
pulled down and it reduces the duty cycle. This event typi- In order to avoid this undesired operation, the OLP circuit is
cally happens when the input voltage is increased or the out- designed to be activated after a specified time to determine
put load is decreased. whether it is a transient situation or an overload situation. In
conjunction with the Ipk current limit pin (if used) the cur-
rent mode feedback path would limit the current in the Sense
FET when the maximum PWM duty cycle is attained. If the
Vcc Vcc
output consumes more than this maximum power, the output
5uA 0.9mA
voltage (Vo) decreases below its rating voltage. This reduces
Vo Vfb
the current through the opto-coupler LED, which also
3 OSC

CFB
+ D1 D2
2.5R reduces the opto-coupler transistor current, thus increasing
VFB
VFB,in
Gate
the feedback voltage (VFB). If VFB exceeds 3V, the feed-
- R driver back input diode is blocked and the 5uA current source (IDE-
431
LAY) starts to charge Cfb slowly up to Vcc. In this condition,
VFB increases until it reaches 6V, when the switching opera-
OLP tion is terminated as shown in Figure 6. The shutdown delay
VSD
time is the time required to charge Cfb from 3V to 6V with
5uA current source.

Figure 5. Pulse Width Modulation (PWM) Circuit

9
www.DataSheet4U.com

FSDH321, FSDL321

PWM
VFB COMPARATOR

VFB,in CLK
Over Load Protection LEB Drain
Gate Driver

6V
Vsense
AOCP
COMPARATOR S Q

R
3V

VAOCP Rsense
t12= CFB×(V(t2)-V(t1)) / IDELAY

t1 t2 t

V (t 2 ) − V (t1 ) Figure 7. Abnormal Over Current Protection (AOCP)

t12 = C FB ; I DELAY = 5 µA, V (t1 ) = 3V , V (t 2 ) = 6V
I DELAY

Figure 6. Over Load Protection (OLP)

4.4 Over Voltage Protection (OVP) : In the event of a mal-

function in the secondary side feedback circuit, or an open
feedback loop caused by a soldering defect, the current
through the opto-coupler transistor becomes almost zero
4.2 Thermal Shutdown (TSD) : The Sense FET and the (refer to Figure 5). Then, VFB climbs up in a similar manner
control IC are integrated, making it easier for the control IC to the over load situation, forcing the preset maximum cur-
to detect the temperature of the Sense FET. When the tem- rent to be supplied to the SMPS until the over load protection
perature exceeds approximately 145°C, thermal shutdown is is activated. Because excess energy is provided to the output,
activated. the output voltage may exceed the rated voltage before the
over load protection is activated, resulting in the breakdown
of the devices in the secondary side. In order to prevent this
situation, an over voltage protection (OVP) circuit is
4.3 Abnormal Over Current Protection (AOCP) : Even employed. In general, Vcc is proportional to the output volt-
though the FPS has OLP (Over Load Protection) and current age and the FPS uses Vcc instead of directly monitoring the
mode PWM feedback, these are not enough to protect the output voltage. If VCC exceeds 19V, OVP circuit is activated
FPS when a secondary side diode short or a transformer pin resulting in termination of the switching operation. In order
short occurs. In addition to start-up, soft-start is also to avoid undesired activation of OVP during normal opera-
activated at each restart attempt during auto-restart and when tion, Vcc should be properly designed to be below 19V.
restarting after latch mode is activated. The FPS has an
internal AOCP (Abnormal Over Current Protection) circuit,
as shown in Figure 7. When the gate turn-on signal is applied
to the power Sense FET, the AOCP block is enabled and
monitors the current through the sensing resistor. The
voltage across the resistor is then compared with a preset
AOCP level. If the sensing resistor voltage is greater than the
AOCP level, pulse-by-pulse AOCP is triggered regardless of
uncontrollable LEB time. Here, pulse-by-pulse AOCP stops
the Sense FET within 350ns after it is activated.

10
www.DataSheet4U.com

FSDH321, FSDL321

5. Soft Start : The FPS has an internal soft start circuit that Burst Burst
slowly increases the feedback voltage together with the Operation Operation

Sense FET current after it starts up. The typical soft start VFB Normal
Operation
time is 15msec, as shown in Figure 8, where progressive
increments of the Sense FET current are allowed during the VBURH
start-up phase. The pulse width to the power switching
VBURL
device is progressively increased to establish the correct
Current
working conditions for transformers, inductors, and capaci- Waveform
tors. The voltage on the output capacitors is progressively Switching Switching
OFF OFF
increased with the intention of smoothly establishing the
required output voltage. It also helps to prevent transformer
saturation and reduce the stress on the secondary diode. +

VBURH -

Drain current Vcc

VBURL/VBURH
0.7A
IBUR(pk)
1ms Vcc Vcc
15steps

IFB
Vfb IDELAY Normal
Current limit 3 PWM
0.4A 2.5R Burst
R
t MOSFET
Current

Figure 8. Soft Start Function

Figure 9. Burst Operation Function

6. Burst Operation : In order to minimize power dissipation

7. Frequency Modulation : Modulating the switching fre-
in standby mode, the FPS enters burst mode operation. As
quency of a switched power supply can reduce EMI. Fre-
the load decreases, the feedback voltage decreases. As
quency modulation can reduce EMI by spreading the energy
shown in Figure 9, the device automatically enters burst
over a wider frequency range than the bandwidth measured
mode when the feedback voltage drops below
by the EMI test equipment. The amount of EMI reduction is
VBURH(500mV). Switching still continues but the current
directly related to the depth of the reference frequency. As
limit is set to a fixed limit internally to minimize flux density
can be seen in Figure 10, the frequency changes from 97KHz
in the transformer. The fixed current limit is larger than that
to 103KHz in 4ms for the FSDH321 (48.5KHz to 51.5KHz
defined by VFB = VBURH and therefore, VFB is driven
for FSDL321). Frequency modulation allows the use of a
down further. Switching continues until the feedback voltage
cost effective inductor instead of an AC input mode choke to
drops below VBURL(350mV). At this point switching stops
satisfy the requirements of world wide EMI limits.
and the output voltages start to drop at a rate dependent on
the standby current load. This causes the feedback voltage to
rise. Once it passes VBURH(500mV), switching resumes.
The feedback voltage then falls and the process repeats. Drain
Burst mode operation alternately enables and disables Current
switching of the power Sense FET thereby reducing switch-
ing loss in Standby mode. ts
fs=1/ts

103kHz
100kHz
97kHz

4ms t

Figure 10. Frequency Modulation Waveform

11
www.DataSheet4U.com

FSDH321, FSDL321

8. Adjusting Peak Current Limit : As shown in Figure 13,

a combined 2.8kΩ internal resistance is connected to the
non-inverting lead on the PWM comparator. A external
resistance of Rx on the current limit pin forms a parallel
resistance with the 2.8kΩ when the internal diodes are
Amplitude (dBµV)

biased by the main current source of 900uA.

Vcc Vcc

5uA 900uA PWM

Vfb
IDELAY IFB
2k Ω Comparator
3

0.8kΩ
Ipk
Frequency (MHz) 4 SenseFET
Current
Sense
Rx
Figure 11. KA5-series FPS Full Range EMI scan(67KHz,
no Frequency Modulation) with DVD Player SET

Figure 13. Peak Current Limit Adjustment

For example, FSDx321 has a typical Sense FET peak current

limit (ILIM) of 0.7A. ILIM can be adjusted to 0.5A by insert-
Amplitude (dBµV)

ing Rx between the Ipk pin and the ground. The value of the
Rx can be estimated by the following equations:

0.7A : 0.5A = 2.8kΩ : XkΩ ,

X = Rx || 2.8kΩ .

(X represents the resistance of the parallel network)

Frequency (MHz)

Figure 12. FSDX-series FPS Full Range EMI Scan (67KHz,

with Frequency Modulation) with DVD Player SET

12
www.DataSheet4U.com

FSDH321, FSDL321

Application Tips

1. Methods of Reducing Audible Noise

Switching mode power converters have electronic and

magnetic components, which generate audible noises when
the operating frequency is in the range of 20~20,000 Hz.
Even though they operate above 20 kHz, they can make
noise depending on the load condition. Designers can
employ several methods to reduce these noises. Here are
three of these methods:

Glue or Varnish

The most common method involves using glue or varnish

to tighten magnetic components. The motion of core, bobbin
and coil and the chattering or magnetostriction of core can
cause the transformer to produce audible noise. The use of
rigid glue and varnish helps reduce the transformer noise. Figure 14. Equal Loudness Curves
But, it also can crack the core. This is because sudden
changes in the ambient temperature cause the core and the
glue to expand or shrink in a different ratio according to the
temperature.

Ceramic Capacitor

Using a film capacitor instead of a ceramic capacitor as a

snubber capacitor is another noise reduction solution. Some
dielectric materials show a piezoelectric effect depending on
the electric field intensity. Hence, a snubber capacitor
becomes one of the most significant sources of audible
noise. It is considerable to use a zener clamp circuit instead
of an RCD snubber for higher efficiency as well as lower
audible noise. Figure 15. Typical Feedback Network of FPS

Adjusting Sound Frequency

Moving the fundamental frequency of noise out of 2~4 kHz

range is the third method. Generally, humans are more sensi-
tive to noise in the range of 2~4 kHz. When the fundamental 2. Other Reference Materials
frequency of noise is located in this range, one perceives the
noise as louder although the noise intensity level is identical. AN-4134: Design Guidelines for Off-line Forward Convert-
Refer to Figure 14. Equal Loudness Curves. ers Using Fairchild Power Switch (FPSTM)
When FPS acts in Burst mode and the Burst operation is
suspected to be a source of noise, this method may be help- AN-4137: Design Guidelines for Off-line Flyback Convert-
ful. If the frequency of Burst mode operation lies in the ers Using Fairchild Power Switch (FPS)
range of 2~4 kHz, adjusting feedback loop can shift the
Burst operation frequency. In order to reduce the Burst oper- AN-4140: Transformer Design Consideration for Off-line
ation frequency, increase a feedback gain capacitor (CF), Flyback Converters using Fairchild Power Switch
opto-coupler supply resistor (RD) and feedback capacitor (FPSTM)
(CB) and decrease a feedback gain resistor (RF) as shown in
Figure 15. Typical Feedback Network of FPS. AN-4141: Troubleshooting and Design Tips for Fairchild
Power Switch (FPSTM) Flyback Applications

AN-4147: Design Guidelines for RCD Snubber of Flyback

AN-4148: Audible Noise Reduction Techniques for FPS

Applications

13
www.DataSheet4U.com

FSDH321, FSDL321

Typical Application Circuit

Application Output power Input voltage Output voltage (Max current)

PC Auxiliary
10W DC 140~375V 5.0V (2.0A)
Power Supply

Features
• High efficiency (>70% at full load, full input range)
• Low standby mode power consumption (<1W at DC 375V input and 0.5W load)
• Low component count
• Enhanced system reliability through various protection functions
• Low EMI through frequency modulation
• Internal soft-start (15ms)

Key Design Notes

• The delay time for over load protection is designed to be about 13ms with C104 of 22nF. If faster/slower triggering of OLP
is required, C104 can be changed to a smaller/larger value(eg. 47nF for about 30ms).
• The pule-by-pulse peak current limit level(ILIM) is set to default value 0.7A by floating the Ipk pin (#4).
• R102 and C101 clamp the DRAIN voltage of MOSFET below 650V under all conditions.

1. Schematic

D 201 L 201
T1 10uH
140~ 375 EE1625 SB360 5V
VDC (+/-5%)
1 10 2A
INPUT C 201 C 203
R 102 C 101 1000uF 470uF
100kΩ 10nF 16V 16V
1W 630V 7
2

R 101
680kΩ D 101
1W UF 4007
3
D 102 R 103
1N 4937 10Ω
M Vcc 4
5
IC101 Vstr C 102
FSDx321 Drain 6,7,8 47uF
3 D 103 50V R 104
Vfb 1N 4937
2 10Ω
Vcc
5
ZD1
C104 GND
18V ZD2
22nF 1 18V
R 202
6 330Ω
IC 301
H11A 817A
R 203
C 103 2kΩ
10uF R 201
C 202
50V 1kΩ
100nF

C301 R 204
IC201
2.2nF 2kΩ
KA431

10W PC Auxiliary Power Circuit

14
www.DataSheet4U.com

FSDH321, FSDL321

2. Transformer Schematic Diagram

EE1625
Np/2 1
Na
10
Np/2 2 N5V Np/2

3 9
NM Vcc

8
NM Vcc 4 N5V

5 7 Np/2
Na

3. Winding Specification

P in (S → F ) W ire T u rn s W in d in g M e th o d
N p /2 3 → 2 0 .1 5 φ × 1 80 S o le n o id w in d in g
In s u la tio n : P o ly e s te r T a p e t = 0 .0 5 0 m m , 3 L a y e rs
N 5V 10 → 7 0 .5 5 φ × 1 12 S o le n o id w in d in g
In s u la tio n : P o ly e s te r T a p e t = 0 .0 5 0 m m , 3 L a y e rs
N M V cc 4 → 6 0 .2 0 φ × 1 40 S o le n o id w in d in g
In s u la tio n : P o ly e s te r T a p e t = 0 .0 5 0 m m , 3 L a y e rs
N P /2 2 → 1 0 .1 5 φ × 1 80 S o le n o id w in d in g
In s u la tio n : P o ly e s te r T a p e t = 0 .0 5 0 m m , 3 L a y e rs
Na 5 → 6 0 .2 0 φ × 1 34 S o le n o id w in d in g
O u te r In s u la tio n : P o ly e s te r T a p e t = 0 .0 5 0 m m , 3 L a y e rs

4. Electrical Characteristics

P in Spec. R e m a rk

In d u c ta n c e 1－ 3 1 .8 m H 1kH z, 1V

Leakage 1－ 3 100 uH 2 n d s id e a ll s h o r t

5. Core & Bobbin

Core : EER1625
Bobbin : EER1625

15
www.DataSheet4U.com

FSDH321, FSDL321

6. Demo Circuit Part List

Part Value Note Part Value Note

Resistor Inductor
R101 680K 1W L201 10uH -
R102 100K 1W -
R103 10 1/4W Diode
R104 10 1/4W D101 UF4007 PN Ultra Fast
R201 1K 1/4W D102 1N4937 PN Ultra Fast
R202 330 1/4W D103 1N4937 PN Ultra Fast
R203 2K 1/4W D201 SB360 Schottky
R204 2K 1/4W ZD1 1N4746A 18V Zener
ZD2 1N4746A 18V Zener
Capacitor
C101 10nF/630V Film IC
C102 47uF/50V Electrolytic IC101 FSDH321 FPS™
Voltage
C103 10uF/50V Electrolytic IC201 KA431(TL431) reference
C104 22nF/50V Film IC301 H11A817A Opto-Coupler
C201 1000uF/16V Electrolytic
C202 100nF/50V Ceramic
C203 1uF/100V Electrolytic
C204 470uF/16V Electrolytic
C301 2.2nF/35V Ceramic

16
www.DataSheet4U.com

FSDH321, FSDL321

Package Dimensions

8DIP

17
www.DataSheet4U.com

FSDH321, FSDL321

Package Dimensions (Continued)

8LSOP

18
www.DataSheet4U.com

FSDH321, FSDL321

Ordering Information

Product Number Package Marking Code BVDSS fOSC RDS(ON)

FSDH321 8DIP DH321 650V 100KHz 14Ω
FSDL321 8DIP DL321 650V 50KHz 14Ω
FSDH321L 8LSOP DH321 650V 100KHz 14Ω
FSDL321L 8LSOP DL321 650V 50KHz 14Ω

19
www.DataSheet4U.com

FSDH321, FSDL321

DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY
PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY
LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER
DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.

LIFE SUPPORT POLICY

FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES
OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems 2. A critical component in any component of a life support
which, (a) are intended for surgical implant into the body, device or system whose failure to perform can be
or (b) support or sustain life, and (c) whose failure to reasonably expected to cause the failure of the life support
perform when properly used in accordance with device or system, or to affect its safety or effectiveness.
instructions for use provided in the labeling, can be
reasonably expected to result in a significant injury of the
user.

www.fairchildsemi.com

9/29/05 0.0m 001

© 2005 Fairchild Semiconductor Corporation