323-1851-195 (6500 CPL R10.0 SiteManager) Issue2
323-1851-195 (6500 CPL R10.0 SiteManager) Issue2
323-1851-195 (6500 CPL R10.0 SiteManager) Issue2
Fundamentals
6500 / CPL Release 10.0
What’s inside...
Supported features
Site Manager installation
Site Manager overview
Ordering information
Troubleshooting
Appendix A: Extending Site Manager’s Secure Shell and SFTP encryption to 256 bit
For additional office locations and phone numbers, please visit the Ciena web site at www.ciena.com.
BY INSTALLING OR USING THE EQUIPMENT, YOU ACKNOWLEDGE THAT YOU HAVE READ THIS
AGREEMENT AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS.
1. Right to Use License; Restrictions. Subject to these terms, and the payment of all applicable license fees, Ciena
grants to you, as end user, a non-exclusive license to use the Ciena software (the "Software") in object code form
solely in connection with, and as embedded within, the Equipment,. You shall have the right to use the Software solely
for your own internal use and benefit. You may make one copy of the Software and documentation solely for backup
and archival purpose, however you must reproduce and affix all copyright and other proprietary rights notices that
appear in or on the original. You may not, without Ciena's prior written consent, (i) sublicense, assign, sell, rent, lend,
lease, transfer or otherwise distribute the Software; (ii) grant any rights in the Software or documentation not expressly
authorized herein; (iii) modify the Software nor provide any third person the means to do the same; (iv) create
derivative works, translate, disassemble, recompile, reverse engineer or attempt to obtain the source code of the
Software in any way; or (v) alter, destroy, or otherwise remove any proprietary notices or labels on or embedded within
the Software or documentation. You acknowledge that this license is subject to Section 365 of the U.S. Bankruptcy
Code and requires Ciena's consent to any assignment related to a bankruptcy proceeding. Sole title to the Software
and documentation, to any derivative works, and to any associated patents and copyrights, remains with Ciena or its
licensors. Ciena reserves to itself and its licensors all rights in the Software and documentation not expressly granted
to you. You shall preserve intact any notice of copyright, trademark, logo, legend or other notice of ownership from any
original or copies of the Software or documentation.
2. Audit: Upon Ciena's reasonable request, but not more frequently than annually without reasonable cause, you
shall permit Ciena to audit the use of the Software at such times as may be mutually agreed upon to ensure
compliance with this Agreement.
3. Confidentiality. You agree that you will receive confidential or proprietary information ("Confidential Information")
in connection with the purchase, deployment and use of the Equipment. You will not disclose Confidential Information
to any third party without prior written consent of Ciena, will use it only for purposes for which it was disclosed, use your
best efforts to prevent and protect the contents of the Software from unauthorized disclosure or use, and must treat it
with the same degree of care as you do your own similar information, but with no less than reasonable care. You
acknowledge that the design and structure of the Software constitute trade secrets and/or copyrighted materials of
Ciena and agree that the Equipment is Confidential Information for purposes of this Agreement.
4. U.S. Government Use. The Software is provided to the Government only with restricted rights and limited rights.
Use, duplication, or disclosure by the Government is subject to restrictions set forth in FAR Sections 52-227-14 and
52-227-19 or DFARS Section 52.227-7013(C)(1)(ii), as applicable. The Equipment and any accompanying technical
data (collectively "Materials") are commercial within the meaning of applicable Federal acquisition regulations. These
Materials were developed fully at private expense. U.S. Government use of the Materials is restricted by this
Agreement, and all other U.S. Government use is prohibited. In accordance with FAR 12.212 and DFAR Supplement
227.7202, software delivered to you is commercial computer software and the use of that software is further restricted
by this Agreement.
5. Term of License. This license is effective until terminated. Customer may terminate this license at any time by
giving written notice to Ciena [or] and destroying or erasing all copies of Software including any documentation. Ciena
may terminate this Agreement and your license to the Software immediately by giving you written notice of termination
in the event that either (i) you breach any term or condition of this Agreement or (ii) you are wound up other than
voluntarily for the purposes of amalgamation or reorganization, have a receiver appointed or enter into liquidation or
bankruptcy or analogous process in your home country. Termination shall be without prejudice to any other rights or
remedies Ciena may have. In the event of any termination you will have no right to keep or use the Software or any
copy of the Software for any purpose and you shall destroy and erase all copies of such Software in its possession or
control, and forward written certification to Ciena that all such copies of Software have been destroyed or erased.
7. Limitation of Liability. ANY LIABILITY OF Ciena SHALL BE LIMITED IN THE AGGREGATE TO THE AMOUNTS
PAID BY YOU FOR THE SOFTWARE. THIS LIMITATION APPLIES TO ALL CAUSES OF ACTION, INCLUDING
WITHOUT LIMITATION BREACH OF CONTRACT, BREACH OF WARRANTY, NEGLIGENCE, STRICT LIABILITY,
MISREPRESENTATION AND OTHER TORTS. THE LIMITATIONS OF LIABILITY DESCRIBED IN THIS SECTION
ALSO APPLY TO ANY THIRD-PARTY SUPPLIER OF Ciena. NEITHER Ciena NOR ANY OF ITS THIRD-PARTY
SUPPLIERS SHALL BE LIABLE FOR ANY INJURY, LOSS OR DAMAGE, WHETHER INDIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL INCLUDING WITHOUT LIMITATION ANY LOST PROFITS, CONTRACTS,
DATA OR PROGRAMS, AND THE COST OF RECOVERING SUCH DATA OR PROGRAMS, EVEN IF INFORMED
OF THE POSSIBILITY OF SUCH DAMAGES IN ADVANCE
8. General. Ciena may assign this Agreement to any Ciena affiliate or to a purchaser of the intellectual property rights
in the Software, but otherwise neither this Agreement nor any rights hereunder may be assigned nor duties delegated
by either party, and any attempt to do so will be void. This Agreement shall be governed by the laws of the State of
Maryland (without regard to the conflict of laws provisions) and shall be enforceable in the courts of Maryland. The
U.N. Convention on Contracts for the International Sale of Goods shall not apply hereto. This Agreement constitutes
the complete and exclusive statement of agreement between the parties relating to the license for the Software and
supersedes all proposals, communications, purchase orders, and prior agreements, verbal or written, between the
parties. If any portion hereof is found to be void or unenforceable, the remaining provisions shall remain in full force
and effect.
Contents 0
2-6 Installing the SFTP Server on a PC, Sun Solaris, or Linux workstation 2-15
2-7 Installing technical documentation files 2-17
Troubleshooting 5-1
Supported features 1-
This chapter lists the features supported by Site Manager for 6500 / CPL
Release 10.0.
Supported features
Site Manager for 6500 / CPL Release 10.0 provides support for the following
functions:
• node information
• optical time domain reflectometer (OTDR) provisioning and graphing
• fault and alarm management
• equipment and facility management
• control plane
• PM viewing and threshold setting
• PM graphing
• upgrades and release management
• backup and restore
• card logs
• protection provisioning, status and exerciser
• span of control
• operational measurements viewing
• events
• restarts
• TL1 command builder
• challenge/response calculator
• nodal SLAT assistant tool and node setup
• shelf level view
• security management
• connection management
Table 1-1 on page 1-3 to Table 1-9 on page 1-24 describe the various items
that can be found under each menu in Site Manager.
File menu
Table 1-1 describes the items in the File menu.
Table 1-1
File menu
Login Opens the Login dialog box requiring connection and security
information for the network element login.
Autologin Initiates log in to the network element using the user ID and
password of the previous successful login.
Passwords are remembered per product type. The last
successful login user ID and password per product type is used
for autologins.
Login as Opens the Login dialog box for the selected network element
which allows the user to log in to the network element with a
user ID and password.
Note: Passwords and user IDs are case sensitive.
When multiple nodes are selected, each selected node will be
logged in using the first user ID and password.
Multiple "Login As…" dialogs will not be displayed.
Logout Logs out the node but leaves the node representation in the
Navigation Tree. If the node is not being used as a gateway for
any other node in the navigation tree, the socket will be closed
and connection will not be maintained with the node.
Disconnect All nodes will be logged out (if logged in), disconnected and
removed from the tree. A confirmation dialog appears before
this action is completed.
Show Nodal Shows the Nodal Manager instance for the selected network
Manager element in the navigator. Only visible in the File menu when a
network element is selected in the navigator.
Close Nodal Closes the Nodal Manager instance for the selected network
Manager element in the navigator. Only visible in the File menu when a
network element is selected in the navigator.
Open in new Opens the Nodal Manager instance for the selected network
Window element in the navigator in a separate window from the main
window. Only visible in the File menu when a network element
is selected in the navigator.
Print Sends the current application data to the printer. This capability
is only applicable for applications which contain tables as well
as Shelf Level View.
Exit Logs you out of the network elements (if logged in) and closes
the Site Manager application.
Edit menu
Table 1-2 describes the items in the Edit menu.
Table 1-2
Edit menu
Tools menu
Table 1-3 describes the items in the Tools menu.
Table 1-3
Tools menu
Comm log Displays the Comm log dialog box for the selected network
element. The Comm log dialog box displays all TL1
commands, responses and autonomous messages between
the network element and Site Manager.
TL1 Command Displays the TL1 Command Builder. Use this window to edit
Builder and run TL1 commands or to build, edit, and run scripts.
Node Setup Opens the Node Setup application, which guides you
through the configuration of the required shelf
communication settings based on the shelf type (primary,
standalone, or member).
This item applies to 6500 only.
General Broadcast Allows you to send or receive messages from one or several
network elements in a span of control.
Ring APS The Ring APS Configuration Editor application allows you to
Configuration Editor create, edit, and delete configuration files that define
BLSR/MS-SPRing rings.
This item applies to 6500 only.
6500 > Basic SLAT Provides access to the Basic SLAT Tool. This tool guides the
Tool user through the commissioning process of a 6500 network
element running a release prior to the current release. The
tool supports 6500 releases that can be installed in craft
mode with the current release but excludes the current
release. An error message appears if you try to launch the
Basic SLAT Tool for a network element running the current
release. Refer to “Consolidated Craft mode” on page 1-25 for
a list of 6500 releases that can be installed in craft mode.
6500 > Advanced Provides access to the Advanced SLAT Tool. This tool guides
SLAT the user through the commissioning process of a 6500
network element running the current release or a release
prior to the current release. The tool supports 6500 releases
that can be installed in craft mode with the current release.
Refer to “Consolidated Craft mode” on page 1-25 for a list of
6500 releases that can be installed in craft mode.
CPL > SLAT Tool Provides access to the SLAT Tool. This tool guides the user
through the commissioning process of a CPL network
element running the current release or a release prior to the
current release. The tool supports CPL releases that can be
installed in craft mode with the current release. Refer to
“Consolidated Craft mode” on page 1-25 for a list of CPL
releases that can be installed in craft mode.
Fault menu
Table 1-4 describes the items in the Fault menu. For more information about
alarms, refer to Fault Management - Alarm Clearing, 323-1851-543 for 6500
or 323-1661-543 for CPL.
Table 1-4
Fault menu
Active Alarms Opens the Active Alarms application that provides the
following:
• Sorted list of alarms
• Alarm details
• Filtering of alarms based on severity
• Auto-refresh or manual refresh of alarms list
• Consolidation of all logged-in NE alarms
• Launch of the online help through the How to Clear button
Historical Fault Opens the Historical Fault Browser application that provides
Browser the following:
• View of historical (current and cleared) alarms for the NE
• View of logs
• Filtering of alarms based on severity
• Filtering of cleared alarms and logs
• Details for specific events (alarms or logs)
Up to 5000 events are stored on the NE.
Active Disabled Allows the user to view active alarm points that have been
Alarms disabled through the alarm profiles and to perform a manual
refresh of the alarm list.
Alarm Cut-Off Opens the Alarm Cut-off dialog box and allows the user to clear
audible alarms.
Clear Security Opens the Clear Security Alarms dialog box and allows the
Alarms user to clear security alarms.
Restart Opens the restart application which allows the user to perform
a cold or warm restart of the software on any circuit pack in the
network element.
Table 1-4
Fault menu (continued)
Card Logs Opens the Card Logs application, which allows you to collect
logs for a selected circuit pack.
Lamp Test Launches the Lamp Test dialog box that allows the user to
perform a lamp test on a selected circuit pack, pluggable, or the
entire shelf.
Configuration menu
Table 1-5 describes the items in the Configuration menu.
Table 1-5
Configuration menu
Node Information • Displays and allows the user to provision the login banner.
• Displays and allows the user to provision Time of Day (NTP
provisioning).
• Displays and allows the user to provision general and system
defaults, as well as shelf and member information per shelf.
Optical Time • Allows the user to retrieve telemetry facilities and to start and
Domain stop OTDR traces.
Reflectometer • Allows the user to retrieve a list of completed Standard OTDR
Record (SOR) files and to download SOR files.
This item applies to 6500 only.
Shelf Level View • Provides a graphical view of the inventory of the network
element, the provisioning of various equipment, and alarm
information on a per circuit pack basis.
• Represents the various states of the circuit packs in graphical
forms.
• Provides access to both Equipment and Facility Provisioning
and Active alarms applications.
• Allows the user to provision new equipment in empty slots
and perform lamp tests.
• Shows equipment protection group and the I/O panel
associated with circuit packs.
Note: The above are incorporated into the Visualization tool at
both the “Site Equipment” view and the “Physical Shelf” view.
Equipment Group Allows the user to manage equipment groups for eMOTR
circuit packs.
This item applies to 6500 only.
Shelf Inventory Allows the user to view information on all physically present
hardware in a network element.
Note: The product engineering code (PEC) displayed does not
include the E5/E6 suffix used in some ordering codes if
applicable.
Facility Inventory Allows the user to view information on all provisioned facilities
per facility category. Facility categories are: Electrical, Layer-0,
Layer-2, OCn/STMn, OTMn, OTN, and Adjacency Discovery.
CPL supports Layer-0 only.
Integrated Test Set Allows the user to validate 10G, 40G, and 100G circuits
through integrated test capabilities.
This item applies to 6500 only.
TMUX Provisioning Guides the user through the facility and cross-connect
Tool provisioning required to create a transmux connection.
The TMux Provisioning Tool is launched from the Path
Connections application.
This item applies to 6500 only.
Cross Connections Allows the user to retrieve, add, and delete transponder
> Transponder connections.
Connections This item applies to 6500 only.
Cross Connections Allows the user to retrieve the number of path connections for
> Count Path each rate in all the shelves that belong to a consolidated TID.
Connections This item applies to 6500 only.
Cross Connections Allows the user to retrieve, add, and delete OTN, FCC, and
> OTN Connections VCP connections.
This item applies to 6500 only.
Cross Connections Allows the user to retrieve, add, and delete photonic
> Photonic connections.
Connections
Cross Connections Allows the user to retrieve, add, and delete EVPL connections.
> EVPL This item applies to 6500 only.
Connections
Tandem Connection Allows the user to manage and provision TCM facilities.
Monitoring This item applies to 6500 only.
Data Services > Allows the user to map the Pbits (customer Ethernet priority)
Receive Class of and CFI usage in the service provider network to one of the
Service Profiles eight Ciena class of services (CoS).
This item applies to 6500 only.
Data Services > Allows the user to map one of the eight Ciena class of services
Transmit Class of (CoS) to the Pbits (customer Ethernet priority) and CFI usage
Service Profiles in the service provider network.
This item applies to 6500 only.
Data Services > Allows the user to manage the egress traffic for LAN (ETH) and
Class of Service WAN ports on L2RPR cards.
Scheduler This item applies to 6500 only.
Data Services > Allows the user to set bandwidth profiles, VCS’, VCEs and end
Service Activation point mappings in order to complete the L2SS data service
Setup activation. TNS and TNEs and their end point mappings are
also available to provision L2 RPR data services.
This item applies to 6500 only.
Data Services > Allows the user to add, delete, edit and refresh bandwidth
Bandwidth Profiles profiles. A profile can also be set as default for each class of
service.
This item applies to 6500 only.
Data Services > Allows the user to add, delete, edit and refresh VCS’ as well as
Segment to add VCEs. Add, delete, edit and refresh can also be
Management performed for TNS’ and associated TNEs.
This item applies to 6500 only.
Data Services > Allows the user to add, delete, edit and refresh VCEs, display
Endpoint VCS’ for selected VCEs and display CTAG mapping of selected
Management VCEs. Also allows the user to add endpoint mappings. Add,
delete, edit, and refresh on TNEs displays TNS’ for selected
TNEs as well as add and delete tunnel endpoint mappings.
This item applies to 6500 only.
Data Services > Allows the user to delete, edit and refresh endpoint maps.
Endpoint Mappings This item applies to 6500 only.
Data Services > Allows the user to provision and manage resilient packet rings
RPR Ring (RPR). This application allows the user to view, add, edit and
Management delete ring provisioning and protection information. This
application also displays Quality of Service parameters.
This item applies to 6500 only.
Data Services > Allows the user to view the topology and bandwidth allocation
RPR Ring information for resilient packet rings (RPR).
Information This item applies to 6500 only.
Data Services > Allows the user to provision and manage the forwarding
Forwarding databases for resilient packet rings (RPR).
Database This item applies to 6500 only.
Data Services > Allows the user to create and manage different queue group
Queue Group profiles. A queue group specifies which scheduler profile, drop
Profiles profiles and multipliers to be used for creating a port. A profile
can also be set as default for each card type.
This item applies to 6500 only.
Data Services > Allows the user to create and manage different queue group
Queue Group Drop drop profiles. A queue group drop profile specifies the queue
Profiles length, the threshold (percentage of queue length) to start
dropping some green packets, the threshold to drop all green
packets, the threshold to start dropping some yellow packets
and the threshold to drop all yellow packets.
This item applies to 6500 only.
Data Services > Manages the class of service (CoS) weights used by the
Queue Group scheduler on the egress of ETH or ETH10G (LAN), LAG, or
Scheduler Profile WAN facilities on L2SS, 20G L2SS, L2 MOTR, or PDH gateway
circuit packs.
This item applies to 6500 only.
Data Services > Allows the user to view the automatically discovered G.8032
G.8032 ERP Node ERP for L2 MOTR and 20G L2SS ERP configurations.
Information This item applies to 6500 only.
Data Services > Allows the user to add or delete the range for ERP
G.8032 ERP Group configurations.
List This item applies to 6500 only.
Data Services > Allows the user to manage ring, ring ports, ringlet, and ringlet
G.8032 ERP ports for G.8032 ERP configurations.
Management This item applies to 6500 only.
Data Services > Allows the user to manage maintenance domains (MDs),
Ethernet OAM maintenance associations (MAs), maintenance intermediate
Provisioning points (MIPs), maintenance end points (MEPs), remote
maintenance end points (RMEPs), link trace, loopbacks, and
defects for Ethernet configurations.
This item applies to 6500 only.
Photonic Services > Allows the user to provision OTS instances by defining the slot
Photonic sequencing, which is used to derive adjacencies between
Configuration equipment present in the OTS.
Management This item applies to 6500 only.
Photonic Services > Allows the user to manage OTS instances at the photonics
OTS Management equipment level.
Photonic Services > Allows the user to monitor behaviors of the network elements
Domain Optical and display logs against a provisioned DOC instance or facility
Controller (DOC) within the same domain.
Photonic Services > Displays the wavelength topology as it travels OTS entry to exit
Shelf Wavelength points.
Topology
Photonic Services > Allows the user to display and provision the serial channel
SCMD Cascading mux/demux (SCMD) cascade order (SCO) to present the
Order correct port trail to topology applications and to suppress
downstream Loss of Signal alarms on CMD ports in the event
of an upstream optical failure.
Photonic Services > Allows the user to validate optical connections in a colorless
Optical Loopback configuration.
This item applies to 6500 only.
Test Toolkit Allows the user to retrieve, add, edit, and delete test access
sessions and to operate/release loopbacks.
This item applies to 6500 only.
Control Plane > The OSRP Provisioning application allows the user to
OSRP Provisioning commission/decommission OSRP on a 6500 node and to
provision the OSRP nodes, links, and lines.
This item applies to 6500 only.
Control Plane > The Routing Profiles application allows the user to manage
Routing Profiles routes and routing lists.
This item applies to 6500 only.
Control Plane > The Sub-Network Connection application allows the user to
Sub-Network view, add, edit, and delete sub-network connections (SNCs)
Connection and virtual endpoints (VEPs). The application also provides
functionality to regroom, manually switch to protect, and revert
SNCs.
This item applies to 6500 only.
Backup and Opens the Backup and Restore Manager application which
Restore allows you to maintain backup copies of the network element
database as well as restore the network element database.
The user can
• request an NE to save its configuration to a repository
• request an NE to restore its configuration from a repository
• provide a FTP server to allow the host running Site Manager
to act as a repository
• restore the configuration from a local database (CPL only)
Span of Control Allows the user to add or delete remote NEs to or from the span
of control of a gateway NE in private IP mode.
This item applies to 6500 only.
Alarms & Controls > Provides the ability to set up alarm profiles for an alarm class.
Alarm Profiles The network element provides two non-editable predefined
profiles (ALL ENABLED, ALL DISABLED) and allows for three
predefined profiles (User1, User2 and User 3) that are user
editable.
A profile contains all the alarm points applicable for the alarm
class and the status (enabled or disabled). A profile can be
applied to an object (individual facility or circuit pack) of that
alarm class to quickly and conveniently disable multiple alarm
points. Additionally, a default profile can be set for an alarm
class so that when a new object of that class is first
provisioned, the default alarm profile is automatically applied.
Note that only one default profile can be assigned for an alarm
class.
Alarms & Controls > Allows the user to provision external controls. The network
External Controls element is equipped with outputs (control relays) that can be
connected to a piece of external equipment for an operation or
released when necessary (for example, if an alarm is raised
indicating that the network element is on fire, the user can turn
on or “operate” the sprinkler).
Comms Setting Allows the user to view and modify Data Communications
Management Network (DCN) parameters.
Performance menu
Table 1-6 describes the items in the Performance menu. For more information
about performance monitoring, refer to Fault Management - Performance
Monitoring, 323-1851-520 for 6500 or 323-1661-520 for CPL.
Table 1-6
Performance menu
PM profiles Provides the ability for users to manage the threshold values
that are used to trigger threshold crossing alerts (TCAs).
The user can display the PM threshold parameters value and
assign a profile to a facility.
The network element provides two non-editable predefined
profiles (All Off and Factory Default) and allows for four
predefined profiles that are user editable.
A profile contains all the Facility and Physical PM parameters
that are supported on the selected entity. Additionally, a default
profile can be set for an entity so that when a new object of that
entity is first provisioned, the default PM profile is automatically
applied.
Only one default profile can be assigned to an entity.
Facility PM Query Allows the user to monitor and restart untimed counts for the
near-end Receive OTU-BBE, OTU-FEC and OTU HCCS PM
untimed bins on a per OTM2 or OTM3 PM type across the
shelf.
This item applies to 6500 only.
Network Provides access to the Round Trip Delay application. Use this
Measurement Tools application to retrieve the round trip delay measurement for
(Round Trip Delay) FLEX MOTR, OTN FLEX MOTR, or 2xOSC circuit pack
facilities.
This item applies to 6500 only.
Security menu
Table 1-7 describes the items in the Security menu. For more information
about managing network security, refer to Administration and Security,
323-1851-301 for 6500, 323-1661-301 for CPL.
Table 1-7
Security Menu
Manage Raman Allows you to set, change, or remove the Raman password.
Password When set, editing of the Raman facility 'Auto Shut Off Disabled
Time' parameter is only possible after successfully entering
this password. If removed, the 'Auto Shut Off Disabled Time'
parameter can be edited without the use of the Raman
password.
Set Shared Secret Allows the user to set/modify the shared secret.
Intrusion Attempt Manages the Intrusion Attempt Handling settings, displays the
Handling current intrusion attempt and lockout status, and allows the
user to unlock inhibited channels.
Advanced Security Allows the user to enable or disable user ID and password
Settings authentication on the debug port.
Invalid Passwords Allows the user to view a list of invalid passwords as well as to
add or delete passwords from the invalid password list.
Syslog Server Allows the user to view and edit SysLog server settings.
Provisioning
Protection menu
Table 1-8 on page 1-23 describes the items in the Protection menu. For more
information about the Protection applications, refer to Configuration -
Provisioning and Operating, 323-1851-310.
Table 1-8
Protection menu
Protection Status • Displays the protection summary for the network element.
• Displays the current protection schemes and status for the
selected equipment, facilities, and paths.
• Allows the user to perform protection operations on the
selected equipment, facilities, and paths.
OTN Protection • Displays OTN protection summary for the network element.
Status • Displays the current OTN protection schemes and status for
the selected equipment, facilities, and paths.
• Allows the user to perform OTN protection operations on the
selected equipment, facilities, and paths.
OTN Protection • Displays the OTN protection scheme for the equipment type.
Provisioning • Allows the user to manage the OTN protection scheme and
associated parameters for both the facilities and the
equipment separately.
Protection Opens the protection exerciser window which allows the user
Exerciser to manage the protection exerciser schedule, allow or inhibit
the protection exerciser, and execute the protection exerciser.
Window menu
The Window menu allows the user to switch between open windows and the
main Site Manager screen. The Window menu is available when there is an
opened window separate from the main screen. This menu is also available
on Nodal Managers and Tools Windows. Nodal Applications in own windows
can be accessed from Nodal manager Windows’ Window menu.
Help menu
The Help menu allows you to open context sensitive help and the
product-specific technical publications. Table 1-9 describes the items in the
Help menu.
Table 1-9
Help menu
Menu Item Description
Current window Displays information about the application currently displayed
in the Nodal Manager area.
Contents and Index Displays the Site Manager online help table of contents.
How to use help Displays information on navigating the Site Manager online
information.
About Site Manager Displays Site Manager product name, release number, and
copyright information.
6500 Technical Displays a documentation index (in pdf format), allowing the
Documentation user to open specific 6500 technical publications.
All documents must have been already loaded in Site
Manager for this application to be fully operational. Refer to
Procedure 2-7, Installing technical documentation files.
CPL Technical Displays a documentation index (in pdf format), allowing the
Documentation user to open specific CPL technical publications.
All documents must have been already loaded in Site
Manager for this application to be fully operational. Refer to
Procedure 2-7, Installing technical documentation files.
Some applications have a “Retrieve” button with Filter criteria that filters the
data that was previously extracted and cached. If the information is not
available (through a previous “Refresh” or through the initial login), the
Retrieve operation causes TL1 commands to be sent to the network element
in order to extract the latest data. After the data is extracted, the Retrieve
operation no longer causes TL1 commands to be sent to the network element
for the same information or subset of information. The cached data is
automatically updated as changes are reported to the Site Manager session
through Database Change (DBCHG) Autonomous Outputs (AOs). Since the
data was retrieved once and updated through DBCHG AOs, the data remains
up-to-date.
If necessary, you can disable automatic updates through DBCHG AOs using
the Faults > Update on Data Changes menu option. The option remains
disabled for the current session only.
Each product that supports Consolidated Craft retains its own software which
can be installed and launched in a standalone or a consolidated mode. A
Consolidated Craft is created by installing software together in the same
directory.
When installed in a consolidated craft mode, the Site Manager navigator acts
as a common launch pad for the Craft interfaces for the different optical
products.
Attention: Site Manager does not support consolidated craft mode for
Optical Metro 3000.
This chapter describes how to install Site Manager. You can install Site
Manager on a personal computer (PC) running a version of Microsoft
Windows, a Sun workstation, or a Linux workstation. Table 2-1 lists the
procedures in this chapter.
Table 2-1
Procedures for installing Site Manager based on configuration
Installing Site Manager software files on a Sun Solaris or Linux workstation on page
2-8
Installing the SFTP Server on a PC, Sun Solaris, or Linux workstation on page 2-15
Related procedures:
Uninstalling Site Manager from a Sun Solaris or Linux workstation on page 2-13
Text conventions
The following table lists the text conventions used in this document.
Hardkey combinations The plus sign (+) is used to indicate that you must Press Shift+:
press two keys at the same time.
Return key The return key symbol (↵) is used to indicate that cd /tmp ↵
you must press the return key.
User input Angle brackets are used to indicate variable input. Enter <hostname >
The DVD contains both NE and Site Manager install files. NE files are under
the release folder. Site Manager files are under the Site Manager folder.
Installation requirements
Operating platforms
Table 2-2 lists each supported operating platform and the corresponding
supported operating systems.
Table 2-2
Operating platforms
Note: For information about required patches and kernel parameters for Solaris and
Linux, refer to the OneControl Unified Management System Engineering Guide.
Hardware requirements
Table 2-3 identifies the recommended hardware requirements for Site
Manager for standalone and consolidated craft installations.
Table 2-3
Site Manager hardware requirements
PC running Windows 7:
DVD drive or network access Required
Hard disk space 500 Mbyte for a standalone installation
800 Mbyte for a consolidated craft installation
Refer to Chapter 1 for more information on consolidated and standalone
modes
Processor 1 GHz or faster 32-bit (x86) or 64-bit (x64) processor
RAM 4 Gbyte or higher
Sun workstation:
Same as the supported platforms in OneControl platform requirements (see the OneControl
documentation for recommended hardware platforms)
Use the default software parameters with respect to the guided installation option of the operating system
software
Additional hardware
Ensure that you use a Hayes compatible modem.
Equipment connection
Refer to the following technical publications for equipment connection details:
• 6500 Packet-Optical Platform—Installation, 323-1851-201
• Common Photonic Layer—Installation, 323-1661-201
Engineering rules
Attention: The number of sessions specified in this section varies
depending on the memory required by the other processes running on the
PC or workstation and the allocated swap space. If you do not follow the
engineering rules, you will impact the performance of all Site Manager
sessions running on a PC or workstation. Unexpected behavior can occur if
the number of sessions is exceeded.
The same Site Manager session should not be used to login to the same NE
more than once as this can impact global applications such as Alarm Banner
and Consolidated Alarms.
Access methods
Site Manager allows you to access a network element by the following
methods:
• Ethernet (recommended)
• direct cable (RS-232)
Procedure 2-1
Installing Site Manager on a PC
Use this procedure to install Site Manager on a personal computer (PC),
either in a standalone or consolidated craft mode.
Always ensure that older releases are installed first followed by newer
releases. Following this order is essential for proper functionality.
Prerequisites
Before you start the software installation, you must:
• ensure that your system meets the installation requirements. See
Installation requirements on page 2-2
• close all applications before installing Site Manager
Step Action
4 Click OK.
5 Wait for the introduction screen to appear, which recommends you to quit all
programs before continuing.
6 Make sure that you have closed all programs, then click the Next button.
A License Agreement screen appears.
7 After reviewing the License Agreement, select the “I accept” option and click
the Next button.
An Important Information screen appears.
8 After reviewing the Important Information, click the Next button.
An Install Location screen appears.
Step Action
Procedure 2-2
Installing Site Manager software files on a Sun
Solaris or Linux workstation
Use this procedure to install Site Manager on a Sun Solaris 10 or Linux
workstation.
Always ensure that older releases are installed first followed by newer
releases. Following this order is essential for proper functionality.
Prerequisites
Before you start this procedure you must:
• close all applications before installing Site Manager
• ensure that the Solaris or Linux software is installed on the workstation
• be authorized to log in to the workstation as the UNIX root user
• have the Site Manager installation DVD
• if reach through from Optical Network Manager AP is required, root user
access to the AP workstation is required
Hardware
For more information on the minimum and recommended hardware
requirements, see Hardware requirements on page 2-3.
Step Action
Step Action
5 Retrieve the installation files from the appropriate directory by entering the
following command.
For Solaris:
cp /dvdrom/dvdrom0/craft/Solaris/install.bin ./install.bin
For Linux:
cp /media/craft/Linux/install.bin ./install.bin
Attention: The installation can also be done through the command line if
needed. Install the software using the command line by entering
./install.bin -i console ↵
Attention: After each of the previous steps, you will be prompted to click
Next in order to progress to the next step.
Step Action
8 Verify the information displayed in the Pre-Install Summary screen. If all the
information is correct, click Install. If the information is incorrect, click Previous
to go back to the previous screens.
9 Click Done to acknowledge completion of the installation.
For information on running Site Manager, see the Optical Network Manager
Applications Platform Interface Login User Guide, 450-3101-012.
10 Eject the DVD by entering
eject ↵
—end—
Procedure 2-3
Uninstalling Site Manager from a PC
Use this procedure to uninstall Site Manager from a personal computer (PC).
This procedure provides instructions for uninstalling Site Manager using the
Uninstall option in the Site Manager program group. You can also uninstall
Site Manager using Add/Remove Programs in the Windows Control Panel.
Prerequisites
Before you uninstall the software, you must:
• close the Site Manager application
• copy the files you want to keep from the Site Manager folder before they
are deleted during the uninstall procedure
Step Action
Step Action
Procedure 2-4
Uninstalling Site Manager from a Sun Solaris or Linux
workstation
Use this procedure to uninstall Site Manager from a Sun Solaris or Linux
workstation.
Prerequisites
Before you uninstall the software, you must:
• close the Site Manager application
• be authorized to log in to the workstation as the UNIX root user
• copy files you must keep that are resident in the Site Manager directory
Step Action
Attention: This procedure removes all files from the Site Manager directory.
1 Log in to the workstation as the root user by entering the root userID and the
password in the login dialog box.
2 Open a console window.
3 Change to the applications directory by entering
cd /opt/ciena/applications↵
4 Change to the Site Manager directory by entering
cd sitemanager↵
5 Change to the UninstallerData directory by entering
cd UninstallerData↵
6 Launch the Uninstall Site Manager Wizard by entering
./UninstallSiteManager↵
7 In the Uninstall Site Manager Wizard, click Next.
8 Follow the instructions. If you wish to uninstall all Site Manager products,
select Complete Uninstall. If you wish to uninstall specific products, select
Uninstall Specific Features.
9 When the uninstallation is complete, click Done to close the Uninstall Site
Manager Wizard.
The uninstaller will indicate if it was unable to remove any files or folders. It is
recommended that you manually remove these files/folders.
These files include Logs and Login Profiles that can be preserved for
historical reasons.
—end—
Procedure 2-5
Installing Site Manager online help files on a PC
Use this procedure to install Site Manager online help files from previous
releases than the one you are currently running.
Prerequisites
Before you start the online help files installation, you must:
• install Site Manager if it is not already installed on your PC. See Procedure
2-1, Installing Site Manager on a PC
• close all applications before installing Site Manager
Step Action
Procedure 2-6
Installing the SFTP Server on a PC, Sun Solaris, or
Linux workstation
Use this procedure to install the Secure File Transfer Protocol (SFTP) server.
SFTP server installation requires JRE version 1.6.x or higher installed and
registered with the OS. For PC and Sun Solaris, the JRE can be downloaded
from:
http://www.oracle.com/technetwork/java/javase/downloads/index.html
The JRE needs to be installed separately for SFTP server installation since
the JRE that is copied when Site Manager is installed is not registered with the
OS.
The Site Manager SFTP Server does not need to be installed on a PC, Sun
Solaris, or Linux workstation that already has a running SFTP Server
installed.
Prerequisites
Before you start the Site Manager SFTP server installation, you must:
• install Site Manager if it is not already installed on your workstation. See
the following installation procedures:
— Procedure 2-1, Installing Site Manager on a PC
— Procedure 2-2, Installing Site Manager software files on a Sun
Solaris or Linux workstation
• close all applications before installing Site Manager
Step Action
Step Action
4 Make sure that you have closed all programs, then click the Next button.
A License Agreement screen appears.
5 After reviewing the License Agreement, select the “I accept” option and click
the Next button.
An Important Information screen appears.
6 After reviewing the Important Information, click the Next button.
An Install Location screen appears.
7 Select the target folder for the SFTP Server installation. For a PC, the default
folder location is C:\Program Files\Site Manager. For Solaris and Linux, the
default folder location is /opt/ciena/applications/sitemanager. Click the Next
button.
A Pre-Installation Summary screen appears, including Product Name, Install
Folder, and Disk Space Information.
If Site Manager is not installed in the default location, a SFTP Server
Installation warning appears, asking you to install Site Manager or to select a
location that contains Site Manager.
If Site Manager is installed in the default location but the base version is not
compatible, a SFTP Server Installation warning appears, asking you to install
a compatible Site Manager or to select a location that contains a compatible
Site Manager.
If a SFTP Server is already installed in the default location, a SFTP Server
Installation warning appears, asking you to uninstall the current version of the
SFTP server and to run the installer again.
8 Review the information in the Pre-Installation Summary screen and make
sure everything is correct. Click the Install button.
An installation progress screen appears.
9 Upon completion of the install, an Install Complete screen may appear. Click
the Done button to quit the installer.
—end—
Procedure 2-7
Installing technical documentation files
Use this procedure to install technical documentation files in order to enable
Site Manager to display the complete suite of 6500 and CPL technical
publications.
Prerequisites
Before you start installing technical documentation files, you must:
• install Site Manager if it is not already installed on your PC. See
Procedure 2-1, Installing Site Manager on a PC.
• close all applications
• ensure you have a copy of the complete 6500 and CPL 10.0 technical
documentation suite (PDF format). The complete suite of 6500 and CPL
10.0 technical publications is available either from:
— www.ciena.com
— 6500 R10.0 Documentation CD-ROM (NTK564KA)
— CPL R10.0 Documentation CD-ROM (NTT840AL)
• have Adobe Acrobat Reader version 4.0 or higher installed on the PC or
workstation where the Technical Documentation files will be installed
Step Action
Step Action
Attention: Do not change any of the file names. Doing so will result in broken
links between the TechnicalDocumentIndex.pdf file and the technical
publications and will prevent Site Manager from displaying the complete suite
of technical publications.
After all required files have been copied to the Site Manager Technical
Documentation folder, Site Manager can display the complete suite of
technical publications.
—end—
Site Manager is a nodal management tool that you can use to operate,
administer, maintain, and provision network elements. Operations that you
can perform using the Site Manager user interface include:
• monitor alarms and alarm history
• retrieve a historical listing of performance statistics for specific network
elements
• provision performance thresholds according to your performance
management parameters
• provision equipment and facilities
• visualize context relevant data and applications for the selected graphical
representations in tabular, tool-tip and right-click menu formats
(Visualization tool)
• access the Service Aware Operating System (SAOS) Command Line
Interface (CLI)
For information on Site Manager online help, see Online help on page 3-12.
The login window prompts the user for connection type (direct, modem, craft
ethernet, or network) and an IP address followed by login information such as
user id and password.
The login manager enables users to organize and manage multiple network
elements and their associated connection attributes as related login profile(s).
A login profile is a group of network elements which can be loaded in the
navigation area. The login manager allows the user to:
• add, edit, and delete login profiles
• add, edit, and delete network elements in a selected login profile
• select a login profile to be loaded in the navigation area
Operational considerations
The following operational considerations apply when using JWS:
• JWS Site Manager can only manage 6500 or CPL nodes.
• JWS Site Manager can only manage 6500 or CPL nodes running the
same release and the same product type as the node that was launched.
To manage previous releases, use the Site Manager installer version.
When JWS is launched from the primary of a mixed TIDc, JWS supports
management of all members, including CPL nodes.
• JWS Site Manager does not support Consolidated Craft. If you require
Consolidated Craft, use the Site Manager installer version.
• JWS Site Manager does not provide the SSH server (SFTP Server). If you
require SSH server (SFTP Server), use the Site Manager installer version.
• JWS Site Manager executes with any sub-version of Sun JRE 1.7. The
application requires a registered version of JRE on the client.
• JWS Site Manager is cached by the client. Caching is controlled by Java
Web Start, therefore Site Manager launched from different network
elements result in multiple versions being cached on the client machine.
• If the space consumed by the Java Web Start cache becomes too large,
you can use the Java Control Panel plugin to remove applications from the
cache. The Java Control Panel can be used to launch applications in the
Java Web Start cache directly. The Site Manager version contained in the
cache can be launched this way.
• JWS Site Manager might require the user to accept multiple signing
certificates.
• JWS Site Manager does not provide online help.
• JWS Site Manager requires HTTP or Secure HTTP access to the network
element. TCP port 80 is used for web browser access and TCP port 443
is used for secure web browser access.
• Starting with 6500 Release 9.3, the shelf processor (SP) circuit pack kit for
the SP circuit pack (NTK555AA and NTK555ABE5) no longer contains
Site Manager software. Therefore, you cannot launch Site Manager in
JWS format from 6500 network elements equipped with the SP circuit
pack (NTK555AA or NTK555ABE5).
Nodal Managers
Site Manager opens a nodal manager for each logged-in node. Applications
for a node (for example, the Active Alarms and the Equipment and Facility
Provisioning applications) are displayed within the corresponding nodal
manager.
Within a single nodal manager, you can open multiple applications. Each open
application for a node is represented by a tab in the nodal manager.
You can open different applications for each logged-in node. Opening an
application only opens the application for the current nodal manager instance.
If you select a different node, the set of applications previously opened for that
node are displayed in the corresponding nodal manager.
The nodal manager displays the node name/identifier (ID) at the top of the
nodal manager (when displayed in the main window) or in the window’s title
bar (when displayed in a window separate from the main window).
Main window
When you log in to Site Manager, the main window opens. See Main window
layout on page 3-4. You can use the main window to:
• connect to or disconnect from the network
• log in to, log out of, and select network elements
• initiate Site Manager applications
In Figure 3-1 on page 3-4, the nodal manager is displayed in the nodal
manager (application) view area. The information in the main window varies
according to product. For supported products, the nodal manager can be
undocked from the main window and displayed in a separate window, as
shown in Figure 3-2 on page 3-5.
Figure 3-1
Main window layout
Navigate/Window
management area
Figure 3-2
Nodal managers displayed in windows separate from the main window
Main window
When nodal managers are displayed in windows separate from the main
window, the menu items specific to a node appear in the corresponding nodal
manager’s menu bar. In this case, the main window menu bar does not display
these node-specific menu items.
The Add Node button is not displayed when you start Site Manager in nodal
view mode.
For information about the Navigation tab details for specific supported
products, refer to the documentation for that product.
See Alarm indicators on page 3-11 for a description of the labels, colors, and
symbols used to indicate alarms in the Navigation tab.
Selecting a network element from the Navigation tab enables the associated
menus and commands.
Figure 3-3
Site Manager Windows tab
You can use the Windows tab to manage multiple nodal manager instances
and applications as follows:
• select the application to display from the list of open applications for a
node. Each application is represented as a tab in the nodal manager.
• open individual applications for a nodal manager in separate windows (for
supported applications only)
• open multiple nodal manager instances in separate windows outside the
nodal manager view area by undocking the nodal manager from the Site
Manager main window
Icons in the tree structure provide visual indications of the nodal manager,
application, and tool status as follows:
• a square with a solid border for a node indicates that the nodal manager
is displayed in the nodal manager view area (within the main window)
• a square with a solid border for an application indicates that the application
is displayed in the nodal manager, not in a window separate from the nodal
manager
• a square with a solid border and a solid blue top for a nodal manager
indicates that the corresponding nodal manager is displayed in a separate
window (undocked from the main window)
• a square with a solid border and a solid blue top for an application
indicates that the corresponding application is displayed in a separate
window (undocked from the nodal manager)
• a square with a dotted border indicates that the corresponding nodal
manager or application is open but not currently displayed in the nodal
manager view area
• a square with a solid border and a solid blue top indicates that the
corresponding tool is open
Note that:
• tools are always displayed in windows separate from the main window
• the alarm banner appears in the Windows tab only when it is undocked
from the main window
• when the node is logged in but the corresponding nodal manager is
closed, no entry appears in the Windows tab for that node
When using the nodal manager (application) view area to display nodal
managers, the selected nodal manager instance is displayed, and the menu
items for the displayed nodal manager appear in the main window menu bar.
All other open nodal managers and their menu items are hidden.
Alarm banner
The alarm banner displays the total number of active alarms, by severity,
raised against all logged in nodes. You must log in to at least one node to
activate the alarm banner.
If you started Site Manager in nodal view mode, the alarm banner cannot be
displayed in a window separate from the main window.
If Site Manager cannot communicate with a node, the right side of the alarm
banner displays a question mark (?).
See Alarm indicators on page 3-11 for a description of the labels, colors, and
symbols used to indicate alarms in the Alarm banner.
Menu bar
The menu bar appears at the top of the Site Manager main window. The
menus displayed depend on whether a nodal manager instance is displayed
in the nodal manager (application) view area.
The availability and contents of the drop-down menus for a nodal manager
depend on the node type. Some applications are restricted by the security
level of the user ID you use to log in to Site Manager. Menu items that are not
available are grayed out. For information on the applications for a node, refer
to the product documentation or online help.
When all nodal manager instances are hidden, the menu items specific to the
nodes are also hidden. When nodal manager instances are undocked from
the main window, the menu items specific to the nodes appear in the
corresponding nodal manager’s menu bar. In this case, the main window
menu bar does not display these node-specific menu items.
Keyboard shortcuts
You can use the keyboard to access the menus and associated menu items.
The following types of keyboard shortcuts are available: key combinations and
shortcut keys.
The shortcut key for accessing a menu or menu item is indicated by the
underlined letter in the menu or menu item name. For example, to access the
Shelf Level View application using shortcut keys, first press the Alt key to
activate the menu, then press, ‘c’ to access the Configuration menu, and
finally press ‘s’ to open the Shelf Level View application.
Alarm indicators
Alarm notification can be displayed for individual logged-in nodes or for all
logged-in nodes. Alarm notification for individual nodes is displayed in the
Navigation tab in the navigation/window management area (see
Alarm notification in the Navigation tab on page 3-6). Alarm notification for all
nodes is displayed in the alarm banner (see Alarm banner on page 3-9).
The alarm counts represent the new, active, and acknowledged alarms. The
alarm counts update as alarms are raised or cleared.
Alarm labels, color highlighting, and symbols are used as indicators for alarm
notification.
Alarm labels
Table 3-1 describes the labels used for alarm notification.
Table 3-1
Alarm labels
Field Description
Color highlighting
Color highlights indicate a change in the alarm count. When the alarm count
changes, the alarm label includes a color highlight that indicates the severity
of the alarm that was raised or cleared. Color highlights do not appear for
changes in the alarm count caused by user connections.
The alarm banner includes a Clear highlighting button ( ) to reset the color
highlights in the alarm banner and in the Navigation tab for all logged in nodes.
Table 3-2
Color highlights
Color Description
Symbols
Table 3-3 describes the symbols used in alarm notification fields.
Table 3-3
Symbols
Symbol Description
Some preference settings take effect as of the next Site Manager session.
You can set the Site Manager preferences described in Table 3-6 on
page 3-35.
Online help
Site Manager uses Sun Microsystems JavaHelp to provide procedures and
context-sensitive information on windows and dialog boxes.
The online help has a toolbar and two areas (see Figure 3-4 on page 3-14).
Table 3-4 on page 3-13 describes the areas in the help window.
Table 3-4
Online help window
Navigation area Select a tab to switch between the table of contents, index, and
full text search displays.
Full text search Select the right tab to search for a specific
word or part of a word contained in the
help topic.
Figure 3-4
Online help
Previous button
Next button
Table of Contents
tab
Index tab
Search tab
Navigation area
displaying Table of
Contents
Table 3-5
Online help terminology
Term Description
Dialog box A dialog box allows you to adjust operating variables and
appears in a window separate from the main screen. A
dialog box does not contain menus. You cannot change the
size of a dialog box.
Drop-down list A drop-down list is a list that appears when you click the
arrow button on the right side of a field.
Pop-up menu A pop-up menu is a menu that appears when you right-click
on a window or a dialog box.
Scroll bar A scroll bar appears at the right or bottom edge of a dialog
box when the contents are not completely visible. Each
scroll bar contains two scroll arrows and a scroll box. Use
the scroll arrows and the scroll box to scroll through the
contents of the dialog box or area.
Technical Documentation
Site Manager allows you to access technical documents. Select the Technical
Documentation item under the help menu to launch a documentation index (in
pdf format) that allows you to open technical documents comprised in the
suite of technical publications.
You can access the shortcut menus by clicking the right-mouse button over a
title bar, menu bar, or item in the navigation/window management area.
Text conventions
The following table lists the text conventions used in this document.
Hardkey combinations The plus sign (+) is used to indicate that you must Press Shift+:
press two keys at the same time.
Return key The return key symbol (↵) is used to indicate that cd /tmp ↵
you must press the return key.
User input Angle brackets are used to indicate variable input. Enter <hostname >
Procedure 3-1
Starting Site Manager
Use this procedure to start a Site Manager session.
The first time Site Manager logs into a specific type and release of network
element, release specific data must be downloaded via remote connection or
a direct network connection to the LAN port on the shelf processor. Once the
initial download is complete, the download will not be attempted for
subsequent logins to the same type and release of network element.
Download of release specific data is not supported over a modem connection
or a direct cable connection.
Attention: When connecting to the LAN port on the shelf processor, use the
default IP address of the NE (10.0.0.1). If the address has been changed,
retrieve the IP address by using the “ipconfig” command in the Windows
command window. The Default Gateway is the address to use to connect to
the NE.
Step Action
Site Manager opens. The Login dialog box or the Login Manager window is
displayed, depending on your preferences settings.
You have completed this procedure.
Starting Site Manager on a Sun Solaris or Linux workstation
3 Change to the directory where Site Manager is installed by entering:
cd <directory> ↵
where
<directory> is the directory where you installed Site Manager. If you
kept the default settings during the installation, the
directory is “/opt/ciena/applications/sitemanager”.
Procedure 3-2
Closing Site Manager
Use this procedure to close a Site Manager session.
Step Action
Attention: A dialog box will appear asking if you want to save the current
node list in a specific profile. If the nodes are already part of an existing
profile, that dialog box will not be displayed.
—end—
Procedure 3-3
Starting Java Web Start Site Manager
Use this procedure to launch Site Manager in a Java Web Start (JWS) format.
Refer to “Java Web Start launch” on page 3-2 for operational considerations
regarding JWS usage.
Attention: Starting with 6500 Release 9.3, the shelf processor (SP) circuit
pack kit for the SP circuit pack (NTK555AA and NTK555ABE5) no longer
contains Site Manager software. Therefore, you cannot launch Site Manager
in JWS format from 6500 network elements equipped with the SP circuit
pack (NTK555AA or NTK555ABE5).
Step Action
Procedure 3-4
Selecting multiple items in the navigation/window
management area
Use this procedure to select multiple nodes, nodal managers, or applications
in the navigation/window management area.
From the Navigation tab, you can perform the following actions simultaneously
on selected supported node types:
• autologin
• login as
• logout
From the Windows tab, you can perform the following actions simultaneously
on selected supported nodal managers or applications:
• open nodal managers in separate windows
• return nodal managers to the main window
• close applications or nodal managers
• open supported applications in separate windows
• return applications to the nodal manager view
Step Action
Attention: When doing a multiple select or a select all in the navigation tree,
you should only try to login to a maximum of 10 nodes at the same time. Not
doing so may result in some of the logins to timeout. In that case, you will
need to login to the timed out nodes individually.
Logging in to the same node (TID) more than once during the same Site
Manager session is not supported as it may affect some global applications
like Alarm Banner and Consolidated Alarms.
Step Action
Attention: Click on the right mouse button to view the supported commands
you can perform on the selected items.
Procedure 3-5
Setting view options for the navigation/window
management area
Use this procedure to show, hide, or maximize the navigation/window
management area.
Note that changing view options for the navigation/window management area
does not affect the main window menu bar.
Step Action
Figure 3-5
Icons for setting navigation/window management area view options
Procedure 3-6
Setting view options for the alarm banner
Use this procedure to:
• display the alarm banner in a window separate from the main window
• return the alarm banner to the main window
Attention: If you started Site Manager in nodal view mode, the alarm
banner cannot be displayed in a window separate from the main window.
Step Action
Displaying the alarm banner in a window separate from the main window
2 Double-click on the alarm banner title in the main window.
You have completed this procedure.
Returning the alarm banner to the main window
3 Click on the “X” box at the top right corner of the alarm banner to return it to
the main menu.
—end—
Procedure 3-7
Setting view options for Site Manager applications
Use this procedure to:
• display an application in a window separate from the nodal manager
• return the application to the nodal manager
Step Action
Procedure 3-8
Resizing windows
Use this procedure to change the size of a window.
Step Action
1 Hold the cursor over the border of the window you want to resize.
If you want to modify Then hold the cursor over the
the width right or left border
the height top or bottom border
both the width and the height window corner
simultaneously
2 When the cursor changes to a double-ended arrow, click and hold the left
mouse button and drag the border until the window or area is the required
size.
3 Release the left mouse button.
Depending on your Site Manager preference settings, the size of the main
window or a nodal manager either returns to the default size or remains
customized the next time you open the window. See Editing Site Manager
preferences on page 3-35. For tool windows (such as the TL1 Command
Builder) or application windows (Shelf Level View and Active alarms), the size
of the window returns to the default size the next time you open the window.
—end—
Procedure 3-9
Resizing table columns
Use this procedure to change the width of a table column in Site Manager.
Step Action
1 Place the cursor in the table heading, over the right margin of the column you
want to resize.
2 When the cursor changes to a double-ended horizontal arrow icon (<—>),
click and hold the left mouse button while you drag the border of the column
to the required column width.
3 Release the left mouse button.
The table column width returns to the default width when you log out or exit
from Site Manager.
—end—
Procedure 3-10
Sorting table columns
Use this procedure to change the order of columns in a table in Site Manager.
Step Action
1 Select the column that you want to move by clicking and holding the left
mouse button on the column heading.
2 Drag the column to the new location.
3 Release the left mouse button.
The order of columns in the table returns to the default display when you log
out or exit Site Manager.
—end—
Procedure 3-11
Sorting table rows
Use this procedure to sort the rows in a table in ascending or descending
alphanumerical order according to the contents of one column.
You can also sort the rows in a table by up to three columns. Refer to the Site
Manager online help for information on the Sort dialog box.
Step Action
1 To sort the rows in a table according to the contents of one column, click on
the column heading.
An icon is displayed in the heading of the column that controls the sort order:
where
indicates that the items in the column are sorted in ascending
order
indicates that the items in the column are sorted in descending
order
Note that:
• You cannot sort the table rows in all windows
• The order of rows in the table returns to the default display order after you
close the window. The sort order for PMs is remembered, even after a
logging out and logging back into the NE.
• Rows are sorted alphanumerically, with the following exceptions:
— Items in the Date and Time columns are sorted by date and then time
— Items in the Name column of the Equipment and Facility Provisioning
application are sorted by slot number
2 To sort the rows in the opposite order, pause, then click again on the same
column heading.
—end—
Procedure 3-12
Copying table data
Use this procedure to copy table data. You can then paste the table data into
another application, such as a text editor.
Step Action
If the tool, application, or nodal manager that contains the table is displayed
in a window that is separate from the main window, ensure that you select the
Edit drop-down menu from the application that contains the table.
—end—
Procedure 3-13
Printing or saving tables
Use this procedure to print or save a table from Site Manager. Use this
procedure if you want to print or save the complete table. If the window
includes more than one table, all tables are printed or saved.
If you want to print or save specific rows of a table, complete the procedure
Copying table data on page 3-33, paste the contents into another application
(such as a text editor), and then print or save the data from that application.
Step Action
Printing a table
3 Print the table as follows:
• If the table appears in a window, select Print from the File menu.
• If the table appears in a dialog box, press Ctrl+p.
4 In the Print dialog box, select a printer and the printing preferences.
5 Click OK.
Saving a table
6 Save the table as follows:
• If the table appears in a window, select Save As from the File menu.
• If the table appears in a dialog box, press Ctrl+s.
7 In the Save As dialog box, select the drive and folder where you want to save
the file.
8 Type the file name in the File name field.
9 Click Save.
The file is saved using the comma-delimited file format.
—end—
Procedure 3-14
Editing Site Manager preferences
Use this procedure to edit preferences for Site Manager. You can edit the
preferences described in Table 3-6.
Table 3-6
Site Manager preferences
Preference Description
General
Startup Select whether the Login dialog box or the Login Manager window opens when
Site Manager is started.
Login Data Specify the maximum number of most-recent entries that appear in the
drop-down list for the Host Name/Address, Login NE fields and Known host lists.
Login Select whether the nodal manager is automatically displayed or hidden upon
node login. Select if unknown host are automatically accepted. Select whether
autologin is enabled or disabled.
Default directory Select the default directory for the current working directory.
Main window size Select whether the Site Manager main window size returns to the default window
upon startup size or to the user specified window size from the last session.
Status area Specify the maximum number of most-recent entries that appear in the
recent history list drop-down list for the main window status area field.
Nodal Manager
Initial applications Specify the Site Manager applications that are automatically opened upon node
login.
Note 1: You select initial applications according to node type.
Note 2: If you select Photonic Connections and any other Site Manager
application as the default while logged into a network element, the Photonic
Connections application might not work as expected. To avoid this problem, do
not select Photonic Connections along with another application as the default.
You can set other applications as the default and then open Photonic
Connections or you can set only Photonic Connections as the default.
Nodal manager Select whether the nodal manager window size returns to the default window size
window size or to the user specified window size from the last nodal manager window.
Note: This preference setting is applicable when the nodal manager is undocked
from the main window.
Nodal manager Specify the maximum number of most-recent entries that appear in the
status area recent drop-down list for the nodal manager status area field.
history list
Preference Description
Time Zone Display Specify whether the timestamps use the Network Element time zone, the Local
OS time zone or another time zone selected by the user.
Visualization
Bay Layout Select whether the Physical Shelf of the Visualization tool displays shelves within
a bay in Top Down (ascending) or Bottom Up (descending) order.
Step Action
1 Select Preferences from the Edit drop-down menu in the main window to
open the Preferences dialog box.
Attention: Changes you make in the Preferences dialog can take effect for
the current session or for the next Site Manager session. Refer to the
information at the bottom of the Preferences dialog to determine when
applied changes take effect.
Step Action
Setting the startup dialog, login data dialog, and the nodal manager view
3 From the left panel of the Preferences dialog, click General.
4 Under Startup, select the startup dialog: Login Dialog or Login Manager.
5 Under Login Data, specify the number of entries to save (1-100) for the Host
Name/Address list, Login NE list, and Known host list fields.
6 Under Login, check the Show Nodal Manager on login box if you want the
nodal manager to be automatically displayed upon node login. Check the
Automatically accept unknown hosts box if you want unknown hosts to be
automatically accepted. Check the Enable Autologin box if you want autologin
to be enabled.
7 Click Apply to apply your changes.
Go to step 2.
Setting the default directory
8 From the left panel of the Preferences dialog, click the plus sign (if it is
displayed) to expand the General item.
9 Under the General item in the left panel of the Preferences dialog, click
Default Directory.
10 Under Default Directory, click Choose.
11 Search for and select the directory to use for the default directory according
to the documentation for your operating system.
12 Click Apply to apply your changes.
Go to step 2.
Setting the main window size at startup and the status area recent history list
13 From the left panel of the Preferences dialog, click the plus sign (if it is
displayed) to expand the General item.
14 Under the General item in the left panel of the Preferences dialog, click View.
15 Specify the main window size at startup: Default window size or Window
size from the last session.
16 In the Status Area list field, specify the number of entries to display (1-100)
that appears in the drop-down list for the main window status area field.
17 Click Apply to apply your changes.
Go to step 2.
Step Action
Attention: If you select Photonic Connections and any other Site Manager
application as the default while logged into a network element, the Photonic
Connections application might not work as expected. To avoid this problem,
do not select Photonic Connections along with another application as the
default. You can set other applications as the default and then open Photonic
Connections or you can set only Photonic Connections as the default.
18 If the Preferences dialog box is not already open, select Preferences from the
Edit drop-down menu in the main window to open the Preferences dialog box.
19 From the left panel of the Preferences dialog, click Nodal Manager.
20 In the NE Type field, select the node type for which you want to set initial
applications.
21 Click Add.
22 In the Add Initial Applications dialog box, do the following:
• From the NE drop down list, select the node for which you want to list
applications.
• In the Applications list, select an application.
• Click OK.
Repeat step 22 to add more applications. If you have completed adding all
required applications, go to step 2.
Attention: The order of applications in the Applications list defines the order,
from left to right, of the application tabs in the nodal manager.
Step Action
When you have set the initial applications, you can use the following buttons
to modify the list:
• Delete: Click this button to delete the selected application.
• Up: Click this button to move the selected application up in the list.
• Down: Click this button to move the selected application down in the list.
Setting the nodal manager window size and the nodal manager status area recent history list
The preference settings in this panel are applicable when the nodal manager
is undocked from the main window.
23 From the left panel of the Preferences dialog, click the plus sign (if it is
displayed) to expand the Nodal Manager item.
24 Under the Nodal Manager item in the left panel of the Preferences dialog,
click View.
25 Specify the nodal manager window size: Default window size or Window
size from last Nodal Manager session.
26 In the Nodal Manager Status Area list field, specify the number of entries to
display (1-100), that appears in the drop-down list for the nodal manager
status area field.
27 Click Apply to apply your changes.
Go to step 2.
Setting the Time Zone display
28 From the left panel of the Preferences dialog, click Time Zone Display.
29 Specify if the timestamps displayed should use the time zone from the
Network Element, Local OS, or Other.
Attention: When selecting Other, you must choose a timezone from the
pull-down menu.
Step Action
Procedure 3-15
Displaying online help
Use this procedure to display online help for Site Manager.
Step Action
Procedure 3-16
Navigating through online help
Use this procedure to navigate through online help.
You can navigate the Site Manager online help through the Table of contents,
the Index, or the Full-text search options from the navigation area. The Table
of contents and Index are organized as a list of topics that you can expand and
collapse. The full-text search allows you to search for a word or part of a word
in the online help; the Site Manager help system will display all entries that
match the search string.
Step Action
Step Action
A topic that contains two exact matches with the search term may appear
higher in the list than a topic that contains five partial matches. A circle and a
number appear beside each topic in the list. The circle indicates the relevance
of the topic and the number indicates the number of times the full or partial
search term appears within the topic.
—end—
Procedure 3-17
Printing an online help topic
Use this procedure to print an online help topic.
Step Action
1 Display the Help window. For instructions, see Displaying online help on page
3-42.
2 Click the Print icon on the toolbar of the Help window.
—end—
Procedure 3-18
Saving an online help topic to a pdf file
Use this procedure to save an online help topic, including an alarm clearing
procedure, to a pdf file.
You must have Adobe Acrobat installed on the PC or workstation where Site
Manager is installed.
Step Action
1 Browse to the required help topic if the topic is not already displayed. For
instructions, see Displaying online help on page 3-42.
2 Click the Print icon on the toolbar of the Help window.
3 Select Adobe PDF from the Name field.
Adobe PDF is available with Adobe Acrobat.
4 Click OK, then specify the folder location and filename for the resulting pdf
file.
—end—
Ordering information 4-
This chapter describes the software and documentation components for Site
Manager for 6500 and CPL Releases 10.0 and 10.05 and provides product
engineering codes (PECs) required to order the components.
To order Site Manager for 6500 and CPL Release 10.0 or 10.05, contact your
local Ciena support organization.
Software
Table 4-1 identifies the PECs for ordering software for Site Manager.
Table 4-1
PECs for 6500 and CPL software
Software PEC
6500 and CPL NE Release 10.0 Software DVD NTK562KA
This PEC includes:
• Site Manager for 6500 Release 10.0 Software
• Site Manager for 6500 / CPL Release 10.0 Fundamentals
(electronic version on DVD)
• 6500 R10.0 network element software
• CPL R10.0 network element software
• SFTP Server application software
6500 and CPL NE Release 10.05 Software DVD NTK562KC
This PEC includes:
• Site Manager for 6500 Release 10.05 Software
• Site Manager for 6500 / CPL Release 10.05 Fundamentals
(electronic version on DVD)
• 6500 R10.05 network element software
• CPL R10.05 network element software
• SFTP Server application software
Right-to-use licenses
Table 4-2 identifies the PECs for ordering right-to-use (RTU) licenses for Site
Manager. You need to order an RTU for each network element.
Table 4-2
PECs for RTU (right-to-use)
Documentation
Table 4-3 identifies the PEC for ordering 6500 and CPL R10.0 technical
publications on CD-ROM.
Table 4-3
PECs for documentation
Product PEC
6500 Packet-Optical Platform Release 10.0 Technical Publications and guides NTK564KA
CD-ROM
Common Photonic Layer Release 10.0 Technical Publications and guides CD-ROM NTT840AL
Note: Site Manager Fundamentals is included on the 6500 Packet-Optical Platform and CPL Technical
Publications and Guides CD-ROM.
Troubleshooting 5-
This chapter provides solutions to situations you may encounter when using
Site Manager.
Possible issues
The following are known possible issues you may experience. For each issue,
a workaround is provided.
Keyboard navigation
The keyboard stops responding if the ALT-key is pressed while changing
between Site Manager applications.
Impact
You are restricted to using the mouse.
Workaround
Minimize and restore the window to recover keyboard navigation.
Text overwriting
Text appears to overwrite itself while retrieving events when using an Exceed
session to access Optical Network Manager (ONM) and then reach through
to Site Manager.
Impact
Event logs are temporarily unreadable.
Workaround
Allow the system to import the information and settle.
Impact
User session to the subtending node is dropped and user will be required to
log in again.
Workaround
There is no workaround to this situation. You must re-login to the subtending
node.
Impact
Frequent unexplained Site Manager disconnections on a Windows PC that
occur within one minute of performing an operation (Retrieval, Add, Edit or
Delete). A "Connection Lost" dialog is displayed with the text "The connection
to <NE TID> has been lost. The network connection was dropped. Please
check the connection and network, and reconnect.". After you select the OK
button, Site Manager closes.
Workaround
Change the windows parameter TcpMaxDataRetransmissions from 5 to 12.
Ciena has found that increasing this parameter from the default of 5 to 12 may
help reduce the issue. Information on modifying Windows communications
settings can be found at http://support.microsoft.com/. Ciena recommends
contacting your computer support team before modifying the PC registry to
ensure the change does not impact other software you use.
Impact
The user cannot perform an invoke operation during an upgrade.
Workaround
Close and re-open Site Manager, then open the Upgrade Management
application.
Shelf Level View application fails to load upon login when set as a default
application
Depending on system load during login, the Configuration > Shelf Level View
application, when set as an application that is automatically loaded upon
login, might not load properly. A blank screen is displayed.
Impact
The Shelf Level View application is unusable.
Workaround
Perform one of the following:
• Refresh the Shelf Level View application by right-clicking on the
application and selecting Open in New Window.
• Remove the Shelf Level View application from the list of default
applications, logout of Site Manager, then login again. Refer to
Procedure 3-14, Editing Site Manager preferences, to set the list of default
applications.
Impact
Site Manager fails to launch.
Workaround
Close other applications consuming high levels of system resources.
If the problem persists, consider upgrading the system memory of your PC.
Procedure 6-1
Download and install the Sun unlimited encryption
policy files for 256 bit encryption
Use this procedure to download and install the Sun unlimited encryption policy
files for Site Manager’s SSH and SFTP 256 bit encryption.
Prerequisites
Before you start downloading and installing the unlimited encryption files, you
must close all applications.
Step Action
Attention: The version of the policy file needed must match the Java
Runtime Environment (JRE) of the Site Manager base.
The JCE Unlimited Strength Jurisdiction Policy Files 5.0 can be found at
http://java.sun.com/javase/downloads/index_jdk5.jsp, under the “Other
Downloads” section.
The JCE Unlimited Strength Jurisdiction Policy Files 6.0 can be found at
http://java.sun.com/javase/downloads/index.jsp, under the “Other
Downloads” section.
3 Double-click the downloaded file and follow the instructions.
4 Open the JCE folder
The JCE folder contains local_policy and US_export_policy jar files and a
read me file.
Replacing the Site Manager encryption policy files
5 Find the Site Manager Installation directory on your PC or workstation.
Step Action
Fundamentals
CONTACT CIENA
For additional information, office locations, and phone numbers, please visit the Ciena web site at
www.ciena.com