Quick Start Guide: T21P Indicator

Quick Start Guide T21P Indicator
ASSEMBLY
MOUNTING THE COLUMN BRACKET
The Indicator can be mounted to a 38mm scale
column (outside diameter) with the supplied
column bracket.
1. Route the cable through the column and
the column bracket.
2. Slide the column bracket down onto the
column and tighten the nut.
3. Solder the load cell cable to the supplied
load cell cable connector. (See Section
1.8.)
4. Slide the indicator onto the bracket as
shown below.
5. Plug the load cell cable into the Indicator’s load cell connector.
6. Remove the upper knob if necessary to change the viewing angle. Then re-install the
knob to fix the position.
LOAD CELL CONNECTION
Connect the load cell cable to the supplied load 5 4 3 2 1
cell cable connector.
9 8 7 6
NOTE: To use a 4-wire load cell cable, short
pins 2 to 8, and pins 6 to 7.
LOAD CELL CONNECTOR PIN CONNECTIONS

Pin 1 2 3 4 5 6 7 8 9
Connection SIG– SENS– N/C N/C GND SENS+ EXC+ EXC– SIG+
CAUTION:
Never connect a communication cable to the load cell connector of the Indicator.
Switch the indicator off when you insert or remove the load cell cable connector
from the Indicator.
NOTE: Connect the load cell cable connector to the load cell cable after routing the cable
through the column and column bracket. (The load cell cable connector cannot pass through
the supplied column bracket.)
Ohaus Corporation www.ohaus.com i T21P Indicator Quick Start Guide

T21P Indicator Quick Start Guide
SAFETY PRECAUTIONS
For safe and dependable operation of this product, please comply with the following
safety precautions:
• Verify that the input voltage printed on the power Adapter and the plug type matches
the local power supply.
• Make sure that the power cord does not pose an obstacle or tripping hazard.
• Disconnect the product from the power supply when cleaning.
• Do not operate this product in hazardous or unstable environments.
• Do not drop loads on the pan.
• Use only approved accessories and peripherals, as available.
• Operate the product only under ambient conditions specified in the Instruction Manual.
• Service should be performed by authorized personnel only.
CONTROLS
AC power
LED
Low Battery
LED Over, Accept &
Under LEDs
7-segment, 6-digit
LED display
Zero, Tare, Stable,

Accum, PCs, Unit
LEDs
Control Buttons
Button
Primary n/a Sample Zero TARE M+ PRINT

Function Enters Sample Sets zero Tares weight of Stores displayed weight Sends the
(Short Press) Setup item on pan in accumulation memory current value to
Saves APW Displays accumulation the RS232
(Avg Piece Wt) data when display is zero Interface
Secondary SET APW N/A N/A N/A MODE

Function Enters Menu Mode Displays APW Change between
(Long Press) Enters Calibration value weighing and
Menu during startup counting mode
Menu Saves settings and N/A ENTER Decrement Increment value of Shift to next digit
Function exits menu Accepts current value of settings settings when setting
(Short Press) setting on display parameters
T21P Indicator Quick Start Guide ii Ohaus Corporation www.ohaus.com

Quick Start Guide T21P Indicator
OPERATION
To turn the Indicator on, toggle the switch on the right side to ON.
The indicator performs a display test, momentarily displays software
version, and then enters the active weighing mode.
To turn power off, toggle the switch to OFF.
Zero is set under the following conditions:
• Automatically at Power On (initial zero).
• Manually by pressing ZERO. (Scale must be stable and within the zero range.)
Manual Tare:
Place a container on the weighing pan and press TARE.
The display shows a net value of “0”.
To clear the Tare value, press TARE with the pan empty.
Weighing: Use this mode to measure the weight of a sample in the selected unit of measure.
1. Press ZERO to set the display to zero.
2. Put an empty container on the pan, and then press TARE to tare the container weight.
3. Add material to the container.
The display shows the weight of the material in the selected unit of measure.
Verify the indicator: place a known mass on the scale and check if the reading is accurate.
If not, calibrate, using the Calibration Guide.
ADDITIONAL OPERATIONS
Changing Units of Measure: Only one unit of measure can be active
at a time (kg or lb).
To select the active unit press and hold SET for three seconds.
Press repeatedly until F1-3 appears. Choose “0” for kg, “1” for lb.
F1-
F1-3
(If selecting “lb”, place the supplied “lb” label over “kg” on the overlay.)
Application Modes: Press and hold PRINTMode to toggle between

Weighing and Counting modes. WEIGH is the default mode.
The Pcs LED illuminates to indicate Counting mode.
To calculate Average Piece Weight, press SAMPLE APW.
[p00010] or the last used value is displayed. Press , , to edit
sample size. Place displayed quantity of samples on scale or in tared
container.
Press SAMPLE to calculate Average Piece Weight (APW).
Scale enters Counting mode.
Press Zero or Sample to exit to Weighing mode.
For other modes – Weight Accumulate or Check Weigh – see Instruction Manual.
Ohaus Corporation www.ohaus.com iii T21P Indicator Quick Start Guide
T21P Indicator Quick Start Guide
MENU NAVIGATION
Press and hold the SET button for three seconds.
SET-Fx will be displayed where x =:
0 = Set upper and lower limit value. 2 = Restores settings to factory default.
1 = User Settings Menu. 3 = Set tare capacity between 2/3Max. and full scale.
To navigate in the Menu Mode:
Press to toggle through available settings.
Press ENTER to accept the displayed setting and advance to the next step.
Press SET at any time to save settings and return to weighing.
MENU SETUP
Parameters Description Settings of “x”
F1-0 x Zero Range 0= 2% of max (default) 2= 10% of max
1= 5% of max 3= 20% of max
F1-1 x Zero Tracking Range 0= 0 division 2= 1 division 4= 3 division
1= 0.5 division (default) 3= 2 division 5= 4 division
6= 5 division
F1-2 x Initial Zero 0= 10% of max 2= 50% of max (default)
1= 20% of max 3= 100% of max
F1-3 x Measuring Unit 0= kg (default)
1= lb
F1-4 x Filter Level 0= Low 2= High
1= Medium (default) 3= Maximum
F1-5 x Stability Indication 0= Fast 2= Medium
1= High (default) 3= Slow
F1-6 x Baud Rate* 0= 9600 (default) 2= 2400
1= 4800 3= 1200
F1-7 x RS232C Output Mode* 0= output Gross, Net, Tare on PRINT key press only (default)
1= output G.N.T., transmit continuously
2= output G.N.T., transmit continuously after stable.
*To activate RS232 settings, press SET key and re-cycle indicator.
F1-9 x Display Brightness 0= low 2= high
1= medium (default) 3= maximum
F1-a x Accumulation Zero Band Accumulation key M+ is effective 1= 0 to 1d
when stable weight returns to 2= 0 to 2d
within x=: 3= 0 to 5d
0= 0 division (default) 4= 0 to 10d
*80252990* P/N 80252990
T21P Indicator Quick Start Guide iv Ohaus Corporation www.ohaus.com

Quick Start Guide: T21P Indicator

Uploaded by

Copyright:

Available Formats

Quick Start Guide: T21P Indicator

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Quick Start Guide: T21P Indicator

Uploaded by

Copyright:

Available Formats

Quick Start Guide T21P Indicator

LOAD CELL CONNECTOR PIN CONNECTIONS

Ohaus Corporation www.ohaus.com i T21P Indicator Quick Start Guide

Zero, Tare, Stable,

Primary n/a Sample Zero TARE M+ PRINT

Secondary SET APW N/A N/A N/A MODE

T21P Indicator Quick Start Guide ii Ohaus Corporation www.ohaus.com

Application Modes: Press and hold PRINTMode to toggle between

80252990 P/N 80252990

T21P Indicator Quick Start Guide iv Ohaus Corporation www.ohaus.com

You might also like