RealVCE

http://www.realvce.com
Free VCE Exam Simulator, Real Exam Dumps File Download
 Huawei H31-341 premium VCE file, real H31-341 questions and answers
IT Certification Guaranteed, The Easy Way!

Exam : H31-341

Title : HCIP-Transmission written

Vendor : Huawei

Version : DEMO

H31-341 premium VCE file, real H31-341 questions and1 answers, H31-341 dumps VCE pdf
https://www.realvce.com/H31-341_free-dumps.html
 Huawei H31-341 premium VCE file, real H31-341 questions and answers
IT Certification Guaranteed, The Easy Way!

NO.1 Which of the following description of the process for optimizing the line attenuation
compensation anomaly is correct? (Multiple choice)
A. According to the user adjustment command, adjust the line attenuation of the OCh path to make
the downstream light output reach the normal value.
B. The SCC board at the downstream site of the fault reports the alarm to the power detection unit
(OA) of the first node through DCN communication, and reports the alarm to the SOM on the SC of
the first node.
C. After receiving the alarm, the SOM obtains the OCh path corresponding to the alarm and adds it to
the management path to be optimized.
D. The downstream power detection unit (OA) detects that the line attenuation deviation exceeds
the threshold and reports the alarm to its own SCC board.
Answer: A,C,D

NO.2 For the whole network error test in the commissioning test, which of the following statement
is correct? (Multiple choice)
A. The duration of the full channel error test is 20 hours. If the error occurs within 20 hours, it needs
to be retested for 20 hours after troubleshooting.
B. The number of OTU boards or tributary boards connected in series for the whole channel error
test is recommended to be no more than 13
C. When the single channel error test is performed, the remote end needs to perform hardware
loopback on the tributary board client side.
D. To ensure the smooth passage of all channel services across the entire network, a 10-minute error
prediction is required for each single channel.
Answer: C,D

NO.3 The ROADM site using WSMD9 board can support up to 9 dimensions. If it exceeds 9
dimensions, it can be implemented by cascading WSMD9 boards.
A. TRUE
B. FALSE
Answer: A

NO.4 Which of the following description of the PM_BIP8 related alarm is correct?
A. The PM_BIP8_OVER alarm indicates that PM error amount has exceeded in the ODU layer.
B. The PM_BIP8_DEG alarm indicates the PM segment signal degradation alarm in the ODU layer.
C. The PM_BIP8_SD alarm indicates the PM segment signal degradation alarm in the OTU layer.
Answer: A

NO.5 Which of the following methods does the networking and application of NG WDM include?
(Multiple choice)
A. Mesh
B. Ring
C. Point to point
D. Chain type

H31-341 premium VCE file, real H31-341 questions and2 answers, H31-341 dumps VCE pdf
https://www.realvce.com/H31-341_free-dumps.html
 Huawei H31-341 premium VCE file, real H31-341 questions and answers
IT Certification Guaranteed, The Easy Way!

Answer: A,B,D

NO.6 The overhead ratio is a factor that affects the error correction capability of FEC technology.
Generally, under the same FEC encoding/decoding algorithm, the higher the overhead ratio, the
greater the net coding benefit.
A. FALSE
B. TRUE
Answer: B

NO.7 Which of the following IP addresses are not part of the private IP address?
A. 192.168.0.1
B. 172.128.0.1
C. 10.255. 0.1
D. 10.0.0.1
Answer: B

NO.8 Which of the following is not included in the OOS overhead?

NO.9 For the SSM protocol, which of the following statements are correct? (Multiple choice)
A. When the standard SSM protocol is started, the clock network can be configured in both
directions but cannot be looped.
B. Whether to start the SSM protocol has little effect on the clock network.
C. When the SSM protocol is not enabled, the clock network can only be configured as one-way and
cannot be looped.
D. When the extended SSM protocol is started, the clock network can be configured in both
directions and can be looped.
Answer: A,C,D

NO.10 Which step is more when the the single board replacement operation of main control board
single configuration than main control board double configuration?
A. Download the original configuration data
B. Query the alarm of the board and confirm that the original alarm has been cleared.
C. Consistency check of network management and network element data.
D. Ensure that the version of the host software is the same before and after the replacement.
Answer: A

NO.11 The following limitations of alarm and performance analysis methods are: (Multiple Choice)
A. In the case of complex networking, service, and fault information, many alarms and performance

H31-341 premium VCE file, real H31-341 questions and3 answers, H31-341 dumps VCE pdf
https://www.realvce.com/H31-341_free-dumps.html
 Huawei H31-341 premium VCE file, real H31-341 questions and answers
IT Certification Guaranteed, The Easy Way!

events may occur along with the occurrence of faults. Due to too many reports and performance
events, maintenance personnel are unable to analyze.
B. When some faults occur, there may be no obvious alarms or performance events reported, and
sometimes no alarms or performance events are found.
C. The network administrator cannot obtain any alarms, time, and historical alarms of the device.
D. Field maintenance personnel cannot understand the current health of the equipment.
Answer: A,B

NO.12 The user-oriented interface and the interface for the transport network of the E-Line service
are ____ and _____.
A. UNI, NNI
B. UNI, UNI
C. NN, NNI
D. NNI, UNI
Answer: A

NO.13 Which of the following protections need to use the APS protocol? (Multiple Choice)
A. SW SNCP protection
B. ODUk SNCP protection
C. ODUk ring network protection
D. 1:1 optical line protection
Answer: C,D

NO.14 Which of the following plane technologies does the OS-OTN device incorporate? (Multiple
Choice)
A. Grouping
B. OTN
C. PDH
D. SDH
Answer: A,B,D

NO.15 For ODUk SNCP protection, if the punch-through site is an electrical relay station, the SCP
type is recommended to be configured as SC/I when configuring protection.
A. TRUE
B. FALSE
Answer: B

NO.16 The following description of the Directioned scenario, which is correct? (Multiple choice)
A. If the current path needs to be adjusted, you must inbound to adjust the fiber connection of the
network.
B. The wavelength carrying the local service can be transmitted to fixed direction.
C. Directioned scenes are applied to networks that are not ASON.
D. When the service needs to be adjusted, or the working path is faulty, the optical crossover can be

H31-341 premium VCE file, real H31-341 questions and4 answers, H31-341 dumps VCE pdf
https://www.realvce.com/H31-341_free-dumps.html
 Huawei H31-341 premium VCE file, real H31-341 questions and answers
IT Certification Guaranteed, The Easy Way!

manually configured to implement flexible scheduling of services.

NO.17 After the PWE3 service is successfully deployed, what is the deployment status of the PWE3
service displayed?
A. Activation
B. Deployment
C. Deployed
D. Activated
Answer: C

NO.18 Which of the following description of the single station commissioning is wrong?
A. In case of power failure, the contact board can be used without anti-static wrist or anti-static
gloves.
B. It is strictly forbidden to plug and unplug the power plug and PIU board.
C. If the input voltage of the equipment is not within the required range, suggestions for rectification
should be proposed.
D. Single station hardware check is complete, make sure all power switches are in the off position
Answer: A

NO.19 In a typical chained NG WDM network (such as A -> B -> C, A, B, and C are three sites), it is
found that the official telephone number between the stations is not available during the
commissioning. What are the possible reasons? (Multiple choice)
A. C station receiving direction OA board damage
B. In the SC2 board configuration of station B, the configuration is incorrectly changed to "the official
does not pass the optical port."
C. B station SC2 board is damaged
Answer: B,C

NO.20 The optical and electronic shelves of the OSN 9800 are connected through the master-slave
subrack cascading mode and connected through the GE 1/2 port on the CTu board.
A. FALSE
B. TRUE
Answer: B

H31-341 premium VCE file, real H31-341 questions and5 answers, H31-341 dumps VCE pdf
https://www.realvce.com/H31-341_free-dumps.html