FINAL

Am27C010
1 Megabit (131,072 x 8-Bit) CMOS EPROM
DISTINCTIVE CHARACTERISTICS
■ Fast access time ■ Latch-up protected to 100 mA from –1 V to
— 45 ns maximum access time VCC + 1 V
■ High noise immunity
■ Low power consumption
■ Versatile features for simple interfacing
— 20 µA typical CMOS standby current
— Both CMOS and TTL input/output compatibility
■ JEDEC-approved pinout
— Two line control functions
■ Single +5 V power supply
■ ± 10% power supply tolerance available ■ Compact 32-pin DIP, PDIP, TSOP, PLCC
packages
■ 100% Flashrite™ programming
— Typical programming time of 16 seconds

GENERAL DESCRIPTION
The Am27C010 is a 1 Megabit ultraviolet erasable pro- controls, thus eliminating bus contention in a multiple
grammable read-only memory. It is organized as 128K bus microprocessor system.
words by 8 bits per word, operates from a single +5 V
AMD’s CMOS process technology provides high
supply, has a static standby mode, and features fast
speed, low power, and high noise immunity. Typical
single address location programming. Products are
power consumption is only 100 mW in active mode,
available in windowed ceramic DIP packages as well
and 100 µW in standby mode.
as plastic one time programmable (OTP) PDIP, TSOP,
and PLCC packages. All signals are TTL levels, including programming sig-
nals. Bit locations may be programmed singly, in
Typically, any byte can be accessed in less than 45 ns,
blocks, or at random. The Am27C010 supports AMD’s
allowing high-performance microprocessors to oper-
Flashrite programming algorithm (100 µs pulses) re-
ate without wait states. The Am27C010 offers sepa-
sulting in a typical programming time of 16 seconds.
rate Output Enable (OE) and Chip Enable (CE)

BLOCK DIAGRAM
VCC Data Outputs
DQ0–DQ7
VSS
VPP

OE Output Enable
Chip Enable Output
CE and Buffers
PGM Prog Logic

Y Y
Decoder Gating

A0–A16
Address
Inputs X 1,048,576
Decoder Bit Cell
Matrix

10205F-1

3 (Replaces Page 2-56) Am27C010

 A M E N D M E N T

PRODUCT SELECTOR GUIDE

Family Part No: Am27C010

Ordering Part No: VCC = 5.0 V ± 5% -45 -255

VCC = 5.0 V ± 10% -45 -55 -70 -90 -120 -150 -200
Max Access Time (ns) 45 55 70 90 120 150 200 250

CE (E) Access (ns) 45 55 70 90 120 150 200 250

OE (G) Access (ns) 25 35 35 40 50 65 75 75

CONNECTION DIAGRAMS
Top View
PDIP PLCC

PGM (P)
VPP 1 32 VCC

VCC
A12
A15
A16
VPP

NC
A16 2 31 PGM (P)
A15 3 30 NC
4 3 2 1 32 31 30
A12 4 29 A14
A7 5 28 A13 A7 5 29 A14
A6 6 27 A8 A6 6 28 A13
A5 7 26 A9 A5 7 27 A8
A4 8 25 A11 A4 8 26 A9
A3 9 24 OE (G) A3 9 25 A11
A2 10 23 A10 A2 10 24 OE (G)
A1 11 22 CE (E) A1 11 23 A10
A0 12 21 DQ7 A0 12 22 CE (E)
DQ0 13 20 DQ6 DQ0 13 21 DQ7
DQ1 14 19 DQ5 14 15 16 17 18 19 20
DQ2 15 18 DQ4
DQ1
DQ2
VSS
DQ3
DQ4
DQ5
DQ6
VSS 16 17 DQ3
10205F-2 10205F-3
Notes:
1. JEDEC nomenclature is in parenthesis.
2. The 32-pin DIP to 32-pin PLCC configuration varies from the JEDEC 28-pin DIP to 32-pin PLCC configuration.

TSOP
A11 1 32 OE
A9 2 31 A10
A8 3 30 CE
A13 4 29 DQ7
A14 5 28 DQ6
NC 6 27 DQ5
PGM 7 26 DQ4
VCC 8 25 DQ3
VPP 9 24 VSS
A16 10 23 DQ2
A15 11 22 DQ1
A12 12 21 DQ0
A7 13 20 A0
A6 14 19 A1
A5 15 18 A2
A4 16 17 A3

Standard Pinout 10205F-4

4 (Replaces Page 2-57) Am27C010

 AMD
PIN DESIGNATIONS LOGIC SYMBOL
A0–A16 = Address Inputs
17
CE (E) = Chip Enable Input A0–A16
DQ0–DQ7 = Data Input/Outputs
8
OE (G) = Output Enable Input DQ0–DQ7
PGM (P) = Program Enable Input CE (E)
VCC = VCC Supply Voltage
PGM (P)
VPP = Program Voltage Input
OE (G)
VSS = Ground
10205F-4

2-58 Am27C010
 A M E N D M E N T

ORDERING INFORMATION
UV EPROM Products
AMD standard products are available in several packages and operating ranges. The order number (Valid Combination) is formed
by a combination of:

AM27C010 -45 D C 5 B

OPTIONAL PROCESSING
Blank = Standard Processing
B = Burn-In

VOLTAGE TOLERANCE
5 = VCC ± 5%, 45 ns only
See Product Selector Guide and
Valid Combinations

TEMPERATURE RANGE
C = Commercial (0°C to +70°C)
I = Industrial (–40°C to +85°C)
E = Extended (–55°C to +125°C)

PACKAGE TYPE
D = 32-Pin Ceramic DIP (CDV032)

SPEED OPTION
See Product Selector Guide and
Valid Combinations

DEVICE NUMBER/DESCRIPTION
Am27C010
1 Megabit (128K x 8-Bit) CMOS UV EPROM

Valid Combinations Valid Combinations

Valid Combinations list configurations planned to be sup-
AM27C010-45 ported in volume for this device. Consult the local AMD sales
DC5, DC5B, DI5, DI5B
VCC = 5.0 V ± 5% office to confirm availability of specific valid combinations and
AM27C010-45 to check on newly released combinations.
VCC = 5.0 V ± 10%
AM27C010-55 DC, DCB, DI, DIB
AM27C010-70
AM27C010-90
AM27C010-120

AM27C010-150 DC, DCB, DE, DEB, DI, DIB

AM27C010-200

AM27C010-255
DC, DCB, DI, DIB
VCC = 5.0 V ± 5%

Am27C010 (Replaces Page 2-59) 5

 A M E N D M E N T

ORDERING INFORMATION
OTP EPROM Products
AMD standard products are available in several packages and operating ranges. The order number (Valid Combination) is formed
by a combination of:

AM27C010 -45 J C 5

OPTIONAL PROCESSING
Blank = Standard Processing

VOLTAGE TOLERANCE
5 = VCC ± 5%, -45 ns only
See Product Selector Guide and
Valid Combinations

TEMPERATURE RANGE
C = Commercial (0°C to +70°C)
I = Industrial (–40°C to +85°C)

PACKAGE TYPE
P = 32-Pin Plastic DIP (PD 032)
J = 32-Pin Rectangular Plastic Leaded Chip
Carrier (PL 032)
E = 32-Pin Thin Small Outline Package
(TSOP) Standard Pinout (TS 032)

SPEED OPTION
See Product Selector Guide and
Valid Combinations

DEVICE NUMBER/DESCRIPTION
Am27C010
1 Megabit (128K x 8-Bit) CMOS OTP EPROM

Valid Combinations Valid Combinations

Valid Combinations list configurations planned to be sup-
AM27C010-45 ported in volume for this device. Consult the local AMD sales
PC5, PI5, JC5, JI5, EC5, EI5
VCC = 5.0 V ± 5% office to confirm availability of specific valid combinations and
AM27C010-45 to check on newly released combinations.
VCC = 5.0 V ± 10%
AM27C010-55
AM27C010-70
AM27C010-90
PC, PI, JC, JI, EC, EI
AM27C010-120
AM27C010-150

AM27C010-200
AM27C010-255
VCC = 5.0 V ± 5%

6 (Replaces Page 2-60) Am27C010

 AMD

FUNCTIONAL DESCRIPTION Am27C010 CE input and VPP = 12.75 V ± 0.25 V, PGM

Low and OE High will program that Am27C010. A
Erasing the Am27C010 high-level CE input inhibits the other Am27C010 de-
In order to clear all locations of their programmed con- vices from being programmed.
tents, it is necessary to expose the Am27C010 to an
ultraviolet light source. A dosage of 15 W seconds/cm2 is Program Verify
required to completely erase an Am27C010. This A verify should be performed on the programmed bits to
dosage can be obtained by exposure to an ultraviolet determine that they were correctly programmed. The
lamp—wavelength of 2537 A° —with intensity of verify should be performed with OE and CE at VIL , PGM
12,000 µW/cm2 for 15 to 20 minutes. The Am27C010 at VIH, and VPP between 12.5 V and 13.0 V.
should be directly under and about one inch from the
Auto Select Mode
source and all filters should be removed from the UV
light source prior to erasure. The auto select mode allows the reading out of a binary
code from an EPROM that will identify its manufacturer
It is important to note that the Am27C010 and similar
and type. This mode is intended for use by programming
devices will erase with light sources having wavelengths
equipment for the purpose of automatically matching
shorter than 4000 A° . Although erasure times will be
the device to be programmed with its corresponding
much longer than with UV sources at 2537 A° , exposure programming algorithm. This mode is functional in the
to fluorescent light and sunlight will eventually erase the 25°C ± 5°C ambient temperature range that is required
Am27C010 and exposure to them should be prevented when programming the Am27C010.
to realize maximum system reliability. If used in such an
environment, the package window should be covered To activate this mode, the programming equipment
by an opaque label or substance. must force 12.0 V ± 0.5 V on address line A9 of the
Am27C010. Two identifier bytes may then be se-
Programming the Am27C010 quenced from the device outputs by toggling address
Upon delivery or after each erasure the Am27C010 has line A0 from VIL to VIH. All other address lines must be
all 1,048,576 bits in the “ONE” or HIGH state. “ZEROs” held at VIL during auto select mode.
are loaded into the Am27C010 through the procedure Byte 0 (A0 = VIL) represents the manufacturer code, and
of programming.
byte 1 (A0 = VIH), the device code. For the Am27C010,
The programming mode is entered when 12.75 V ± these two identifier bytes are given in the Mode Select
0.25 V is applied to the VPP pin, CE and PGM are at VIL, Table. All identifiers for manufacturer and device codes
and OE is at VIH. will possess odd parity, with the MSB (DQ7) defined as
For programming, the data to be programmed is applied the parity bit.
8 bits in parallel to the data output pins. Read Mode
The Flashrite algorithm reduces programming time by The Am27C010 has two control functions, both of which
using 100 µs programming pulses and by giving each must be logically satisfied in order to obtain data at the
address only as many pulses as is necessary in order to outputs. Chip Enable (CE) is the power control and
reliably program the data. After each pulse is applied to should be used for device selection. Output Enable (OE)
a given address, the data in that address is verified. If is the output control and should be used to gate data to
the data does not verify, additional pulses are given until the output pins, independent of device selection. As-
it verifies or the maximum is reached. This process is re- suming that addresses are stable, address access time
peated while sequencing through each address of the (tACC) is equal to the delay from CE to output (tCE). Data
Am27C010. This part of the algorithm is done at is available at the outputs tOE after the falling edge of
VCC = 6.25 V to assure that each EPROM bit is pro- OE, assuming that CE has been LOW and addresses
grammed to a sufficiently high threshold voltage. After have been stable for at least tACC–tOE.
the final address is completed, the entire EPROM mem-
ory is verified at VCC = VPP = 5.25 V. Standby Mode
Please refer to Section 6 for programming flow chart The Am27C010 has a CMOS standby mode which re-
and characteristics. duces the maximum VCC current to 100 µA. It is placed in
CMOS-standby when CE is at VCC ± 0.3 V. The
Program Inhibit Am27C010 also has a TTL-standby mode which re-
Programming of multiple Am27C010 in parallel with dif- duces the maximum VCC current to 1.0 mA. It is placed in
ferent data is also easily accomplished. Except for CE, TTL-standby when CE is at VIH. When in standby mode,
all like inputs of the parallel Am27C010 may be com- the outputs are in a high-impedance state, independent
mon. A TTL low-level program pulse applied to an of the OE input.

Am27C010 2-61
 AMD

Output OR-Tieing System Applications

To accommodate multiple memory connections, a two- During the switch between active and standby condi-
line control function is provided to allow for: tions, transient current peaks are produced on the rising
■ Low memory power dissipation and falling edges of Chip Enable. The magnitude of
these transient current peaks is dependent on the out-
■ Assurance that output bus contention will not occur
put capacitance loading of the device. At a minimum, a
It is recommended that CE be decoded and used as the 0.1-µF ceramic capacitor (high frequency, low inherent
primary device-selecting function, while OE be made a inductance) should be used on each device between
common connection to all devices in the array and con- VCC and VSS to minimize transient effects. In addition, to
nected to the READ line from the system control bus. overcome the voltage drop caused by the inductive ef-
This assures that all deselected memory devices are in fects of the printed circuit board traces on EPROM ar-
low-power standby mode and that the output pins are rays, a 4.7-µF bulk electrolytic capacitor should be used
only active when data is desired from a particular between VCC and VSS for each eight devices. The loca-
memory device. tion of the capacitor should be close to where the power
supply is connected to the array.

MODE SELECT TABLE

Pins CE OE PGM A0 A9 VPP Outputs
Mode
Read VIL VIL X X X X DOUT

Output Disable X VIH X X X X High-Z

Standby (TTL) VIH X X X X X High-Z

Standby (CMOS) VCC ± 0.3 V X X X X X High-Z

Program VIL VIH VIL X X VPP DIN

Program Verify VIL VIL VIH X X VPP DOUT

Program Inhibit VIH X X X X VPP High-Z

Manufacturer
Auto Select Code VIL VIL X VIL VH X 01H
(Note 3)
Device Code VIL VIL X VIH VH X 0E
Notes:
1. VH = 12.0 V ± 0.5 V
2. X = Either VIH or VIL
3. A1–A8 = A10–A16 = VIL
4. See DC Programming Characteristics for VPP voltage during programming.

2-62 Am27C010
 A M E N D M E N T

ABSOLUTE MAXIMUM RATINGS OPERATING RANGES

Storage Temperature Commercial (C) Devices
OTP Products . . . . . . . . . . . . . . . . –65°C to +125°C Ambient Temperature (TA). . . . . . . . . . . .0°C to +70°C
All Other Products. . . . . . . . . . . . . –65°C to +150°C Industrial (I) Devices
Ambient Temperature Ambient Temperature (TA). . . . . . . . . .–40°C to +85°C
with Power Applied. . . . . . . . . . . . . .–55°C to + 125°C Extended (E) Devices
Voltage with Respect to VSS Ambient Temperature (TA). . . . . . . . .–55°C to +125°C
All pins except A9, VPP, VCC . . –0.6 V to VCC +0.5 V Supply Read Voltages
A9 and VPP (Note 2). . . . . . . . . . . . . –0.6 V to +13.5 V VCC for Am27C010-45, 255 . . . . . +4.75 V to +5.25 V
VCC (Note 1). . . . . . . . . . . . . . . . . . . . –0.6 V to +7.0 V VCC for Am27C010-45, 55, 70,
Notes: 90, 120, 150, 200 . . . . . . . . . . . . . +4.50 V to +5.50 V
1. Minimum DC voltage on input or I/O pins is –0.5 V. During
Operating ranges define those limits between which the
voltage transitions, inputs may overshoot VSS to –2.0 V for
functionality of the device is guaranteed.
periods of up to 20 ns. Maximum DC voltage on input and
I/O pins is VCC + 0.5 V. During voltage transitions, input
and I/O pins may overshoot to VCC + 2.0 V for periods up
to 20ns.
2. Minimum DC input voltage on A9 pin is –0.5 V. During
voltage transitions, A9 and VPP may overshoot VSS to
–2.0 V for periods of up to 20 ns. A9 and VCC must not
exceed +13.5 V at any time.
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device. This is
a stress rating only; functional operation of the device at these
or any other conditions above those indicated in the opera-
tional sections of this specification is not implied. Exposure of
the device to absolute maximum rating conditions for ex-
tended periods may affect device reliability.

Am27C010 (Replaces Page 2-63) 7

 AMD

DC CHARACTERISTICS over operating range unless otherwise specified.

(Notes 1, 2, and 4)
Parameter
Symbol Parameter Description Test Conditions Min Max Unit
VOH Output HIGH Voltage IOH = –400 µA 2.4 V
VOL Output LOW Voltage IOL = 2.1 mA 0.45 V
VIH Input HIGH Voltage 2.0 VCC + 0.5 V
VIL Input LOW Voltage –0.5 +0.8 V
ILI Input Load Current VIN = 0 V to VCC 1.0 µA
ILO Output Leakage Current VOUT = 0 V to VCC 5.0 µA
ICC1 VCC Active Current CE = VIL, f = 10 MHz, C/I Devices 30
mA
(Note 3) IOUT = 0 mA E Devices 60
ICC2 VCC TTL Standby Current CE = VIH 1.0 mA
ICC3 VCC CMOS Standby Current CE = VCC ± 0.3 V 100 µA
IPP1 VPP Current During Read CE = OE = VIL, VPP = VCC 100 µA
Notes:
1. VCC must be applied simultaneously or before VPP, and removed simultaneously or after VPP.
2. Caution: The Am27C010 must not be removed from (or inserted into) a socket when VCC or VPP is applied.
3. ICC1 is tested with OE = VIH to simulate open outputs.
4. Minimum DC Input Voltage is –0.5 V. During transitions, the inputs may overshoot to –2.0 V for periods less than 20 ns.
Maximum DC Voltage on output pins is VCC + 0.5 V, which may overshoot to VCC + 2.0 V for periods less than 20 ns.

30 30

25 25
Supply Current

Supply Current
in mA

in mA

20 20

15 15

10 10
1 2 3 4 5 6 7 8 9 10 –75 –50 –25 0 25 50 75 100 125 150
Frequency in MHz Temperature in °C
Figure 1. Typical Supply Current Figure 2. Typical Supply Current
vs. Frequency vs. Temperature
VCC = 5.5 V, T = 25°C VCC = 5.5 V, f = 10 MHz
10205F-6 10205F-7

2-64 Am27C010
 A M E N D M E N T

CAPACITANCE
CDV032 PL 032 PD 032 TS 032
Parameter Parameter Test
Symbol Description Conditions Typ Max Typ Max Typ Max Typ Max Unit

Input
CIN VIN = 0 9 12 8 12 8 12 10 12 pF
Capacitance

Output
COUT VOUT = 0 13 15 11 14 11 14 12 14 pF
Capacitance

Notes:
1. This parameter is only sampled and not 100% tested.
2. TA = +25°C, f = 1 MHz.

AC CHARACTERISTICS
Parameter
Symbols Am27C010
Parameter Test
JEDEC Standard Description Conditions -45 -55 -70 -90 -120 -150 -200 -255 Unit

CE,
tAVQV tACC Address to Output Delay Max 45 55 70 90 120 150 200 250 ns
OE = VIL

Chip Enable to Output

tELQV tCE OE = VIL Max 45 55 70 90 120 150 200 250 ns
Delay

Output Enable to Output

tGLQV tOE CE = VIL Max 25 35 35 40 50 65 75 75 ns
Delay

Chip Enable High or

tEHQZ tDF Output Enable High to
Max 25 25 25 25 35 35 40 40 ns
tGHQZ (Note 3) Output Float, Whichever
Occurs First

Output Hold from

tAXQX tOH Addresses, CE, or OE, Min 0 0 0 0 0 0 0 0 ns
Whichever Occurs First

Notes:
1. Caution: Do not remove the Am27C010 from (or insert it into) a socket or board that has VPP or VCC applied.
2. VCC must be applied simultaneously or before VPP, and removed simultaneously or after VPP.
3. This parameter is sampled and not 100% tested.
4. Switching characteristics are over operating range, unless otherwise specified.
5. Test Conditions for Am27C010-45 and -55:
Output Load: 1 TTL gate and CL = 30 pF
Input rise and fall times: 20 ns
Input pulse levels: 0.0 V to 3.0 V
Timing measurement reference level Inputs and Outputs: 1.5 V
Test Conditions for all others:
Output Load: 1 TTL gate and CL = 100 pF
Input rise and fall times: 20 ns
Input pulse levels: 0.45 V to 2.4 V
Timing measurement reference level Inputs and Outputs: 0.8 and 2.0 V

8 (Replaces Page 2-65) Am27C010

 A M E N D M E N T

SWITCHING TEST CIRCUIT

5.0 V

IN3064
or Equivalent 2.7 kΩ
Device
Under
Test
CL 6.2 kΩ

Diodes = IN3064
or Equivalent

Notes:
For -45 and -55: CL = 30 pF including jig capacitance
For all others: CL = 100 pF including jig capacitance
10205F-8

Figure 1. Test Conditions

SWITCHING TEST WAVEFORM

3V 2.4 V
2.0 V 2.0 V

1.5 V Test Points 1.5 V Test Points

0.8 V 0.8 V
0V 0.45 V
Input Output Input Output

AC Testing for -45 and -55 devices: Inputs are driven at 3.0 V AC Testing (except for -45 and -55 devices): Inputs are driven
for a logic “1” and 0 V for a logic “0”. Input pulse rise and fall at 2.4 V for a logic “1” and 0.45 V for a logic “0”. Input pulse
times are ≤20 ns. rise and fall times are ≤20 ns.

10205F-9

Trademarks

Copyright © 1996 Advanced Micro Devices, Inc. All rights reserved.

AMD, the AMD logo, and combinations thereof are trademarks of Advanced Micro Devices, Inc.
ExpressROM and Flashrite are trademarks of Advanced Micro Devices, Inc.
Product names used in this publication are for identification purposes only and may be trademarks of their respective companies.

Am27C010 (Replaces Page 2-66) 9

 AMD

KEY TO SWITCHING WAVEFORMS

WAVEFORM INPUTS OUTPUTS

Must Be Will Be
Steady Steady

May Will Be
Change Changing
from H to L from H to L

May Will Be
Change Changing
from L to H from L to H

Don’t Care, Changing

Any Change State
Permitted Unknown

Does Not Center

Apply Line is High
Impedence
“Off” State
KS000010

SWITCHING WAVEFORMS

2.4
2.0 Addresses Valid 2.0
Addresses
0.8 0.8
0.45

CE

tCE

OE
tDF
tOE (Note 2)
tACC tOH
(Note 1)
High Z High Z
Output Valid Output

Notes: 10205F-10
1. OE may be delayed up to tACC–tOE after the falling edge of the addresses without impact on tACC.
2. tDF is specified from OE or CE, whichever occurs first.

Am27C010 2-67