Table of Contents

1. SAFETY PRECAUTIONS AND WARNINGS .............................................. 1

2. GENERAL INFORMATION .......................................................................... 2
2.1 ON-BOARD DIAGNOSTICS (OBD) II ................................................................. 2
2.2 DIAGNOSTIC TROUBLE CODES (DTCS) ............................................................ 2
2.3 LOCATION OF THE DATA LINK CONNECTOR (DLC) ........................................ 3
2.4 OBD II READINESS MONITORS ........................................................................ 4
2.5 OBD II MONITOR READINESS STATUS ............................................................. 5
2.6 OBD II DEFINITIONS ........................................................................................ 6
3. USING THE SCAN TOOL .............................................................................. 8
3.1 TOOL DESCRIPTION .......................................................................................... 8
3.2 SPECIFICATIONS .............................................................................................. 10
3.3 ACCESSORIES INCLUDED ................................................................................ 10
3.4 KEYBOARD ...................................................................................................... 10
3.5 POWER ............................................................................................................ 10
3.6 SYSTEM SETUP ................................................................................................ 11
3.7 VEHICLE COVERAGE ...................................................................................... 15
3.8 PRODUCT TROUBLESHOOTING ....................................................................... 16
4. PLAYBACK DATA ....................................................................................... 18
4.1 REVIEWING DATA ........................................................................................... 18
4.2 DELETING DATA ............................................................................................. 19
4.3 PRINTING DATA .............................................................................................. 19
5. DIAGNOSTICS .............................................................................................. 20
5.1 ENTERING VEHICLE INFORMATION ................................................................ 20
5.2 DIAGNOSTIC TEST ........................................................................................... 25
5.3 DIAGNOSTIC OPERATION ................................................................................ 29
6. OBDII DIAGNOSTICS ................................................................................. 36
6.1 READ CODES .................................................................................................... 37
6.2 ERASE CODES ................................................................................................. 40
 6.3 LIVE DATA ....................................................................................................... 42
6.4 FREEZE FRAME ................................................................................................ 48
6.5 RETRIEVING I/M READINESS STATUS............................................................. 49
6.6 O2 MONITOR TEST .......................................................................................... 52
6.7 ON-BOARD MONITOR TEST ............................................................................. 53
6.8 COMPONENT TEST ........................................................................................... 56
6.9 VIEWING VEHICLE INFORMATION ................................................................... 57
6.10 MODULES PRESENT ....................................................................................... 59
6.11 DTC LOOKUP ................................................................................................ 60
7 PRINT DATA ................................................................................................. 62
8 SOFTWARE UPDATE .................................................................................. 64
8.1 REGISTER THE TOOL ...................................................................................... 64
8.2 UPDATE PROCEDURE ...................................................................................... 65
8.3 VIEW OR DELETE PROGRAMS ......................................................................... 67
9 WARRANTY AND SERVICE ...................................................................... 69
9.1 LIMITED ONE YEAR WARRANTY .................................................................... 69
9.2 SERVICE PROCEDURES .................................................................................... 69
1. Safety Precautions and Warnings
To prevent personal injury or damage to vehicles and/or the scan
tool, read this instruction manual first and observe the following
safety precautions at a minimum whenever working on a vehicle:
 Always perform automotive testing in a safe environment.
 Wear safety eye protection that meets ANSI standards.
 Keep clothing, hair, hands, tools, test equipment, etc. away from
all moving or hot engine parts.
 Operate the vehicle in a well ventilated work area: Exhaust gases
are poisonous.
 Put blocks in front of the drive wheels and never leave the vehicle
unattended while running tests.
 Use extreme caution when working around the ignition coil,
distributor cap, ignition wires and spark plugs. These
components create hazardous voltages when the engine is
running.
 Put the transmission in PARK (for automatic transmission) or
NEUTRAL (for manual transmission) and make sure the parking
brake is engaged.
 Keep a fire extinguisher suitable for gasoline/chemical/ electrical
fires nearby.
 Don’t connect or disconnect any test equipment while the
ignition is on or the engine is running.
 Keep the scan tool dry, clean, free from oil/water or grease. Use a
mild detergent on a clean cloth to clean the outside of the scan
tool, when necessary.

1
2. General Information
2.1 On-Board Diagnostics (OBD) II
The first generation of On-Board Diagnostics (called OBD I) was
developed by the California Air Resources Board (ARB) and
implemented in 1988 to monitor some of the emission control
components on vehicles. As technology evolved and the desire to
improve the On-Board Diagnostic system increased, a new generation
of On-Board Diagnostic system was developed. This second generation
of On-Board Diagnostic regulations is called "OBD II".
The OBD II system is designed to monitor emission control systems
and key engine components by performing either continuous or
periodic tests of specific components and vehicle conditions. When a
problem is detected, the OBD II system turns on a warning lamp (MIL)
on the vehicle instrument panel to alert the driver typically by the
phrase of “Check Engine” or “Service Engine Soon”. The system will
also store important information about the detected malfunction so
that a technician can accurately find and fix the problem. Here below
follow three pieces of such valuable information:
1) Whether the Malfunction Indicator Light (MIL) is
commanded 'on' or 'off';
2) Which, if any, Diagnostic Trouble Codes (DTCs) are stored;
3) Readiness Monitor status.

2.2 Diagnostic Trouble Codes (DTCs)

OBD II Diagnostic Trouble Codes are codes that are stored by the
on-board computer diagnostic system in response to a problem found
in the vehicle. These codes identify a particular problem area and are
intended to provide you with a guide as to where a fault might be
occurring within a vehicle. OBD II Diagnostic Trouble Codes
consists of a five-digit alphanumeric code. The first character, a letter,
identifies which control system sets the code. The other four
characters, all numbers, provide additional information on where the
DTC originated and the operating conditions that caused it to set. Here
below is an example to illustrate the structure of the digits:

2
2.3 Location of the Data Link Connector (DLC)
The DLC (Data Link Connector or Diagnostic Link Connector) is the
standardized 16-cavity connector where diagnostic scan tools
interface with the vehicle's on-board computer. The DLC is usually
located 12 inches from the center of the instrument panel (dash),
under or around the driver’s side for most vehicles. If Data Link
Connector is not located under dashboard, a label should be there
telling location. For some Asian and European vehicles, the DLC is
located behind the ashtray and the ashtray must be removed to access
the connector. If the DLC cannot be found, refer to the vehicle’s
service manual for the location.

3
2.4 OBD II Readiness Monitors
An important part of a vehicle’s OBD II system is the Readiness
Monitors, which are indicators used to find out if all of the emissions
components have been evaluated by the OBD II system. They are
running periodic tests on specific systems and components to ensure
that they are performing within allowable limits.
Currently, there are eleven OBD II Readiness Monitors (or I/M
Monitors) defined by the U.S. Environmental Protection Agency
(EPA). Not all monitors are supported by all vehicles and the exact
number of monitors in any vehicle depends on the motor vehicle
manufacturer’s emissions control strategy.
Continuous Monitors -- Some of the vehicle components or systems
are continuously tested by the vehicle’s OBD II system, while others
are tested only under specific vehicle operating conditions. The
continuously monitored components listed below are always ready:
1）Misfire
2）Fuel System
3）Comprehensive Components (CCM)
Once the vehicle is running, the OBD II system is continuously
checking the above components, monitoring key engine sensors,
watching for engine misfire, and monitoring fuel demands.
Non-Continuous Monitors -- Unlike the continuous monitors, many
emissions and engine system components require the vehicle to be
operated under specific conditions before the monitor is ready. These

4
 monitors are termed non-continuous monitors. For different ignition
type engines, the available monitors are different too.
The following monitors are to be used for spark ignition engines
only:
1) EGR System
2) O2 Sensors
3) Catalyst
4) Evaporative System
5) O2 Sensor Heater
6) Secondary air
7) Heated Catalyst
The following monitors are to be used for compression ignition
engines only:
1) EGR System
2) NMHC Catalyst
3) NOx aftertreatment
4) Boost pressure system
5) Exhaust gas sensor
6) PM filter

2.5 OBD II Monitor Readiness Status

OBD II systems must indicate whether or not the vehicle’s PCM’s
monitor system has completed testing on each component.
Components that have been tested will be reported as “Ready”, or
“Complete”, meaning they have been tested by the OBD II system.
The purpose of recording readiness status is to allow inspectors to
determine if the vehicle’s OBD II system has tested all the
components and/or systems.
The power-train control module (PCM) sets a monitor to “Ready” or
“Complete” after an appropriate drive cycle has been performed. The
drive cycle that enables a monitor and sets readiness codes to “Ready”
varies for each individual monitor. Once a monitor is set as “Ready”
or “Complete”, it will remain in this state. A number of factors,
5
 including erasing of diagnostic trouble codes (DTCs) with a scan tool
or a disconnected battery, can result in Readiness Monitors being set
to “Not Ready”. Since the three continuous monitors are constantly
evaluating, they will be reported as “Ready” all of the time. If testing
of a particular supported non-continuous monitor has not been
completed, the monitor status will be reported as “Not Complete” or
“Not Ready.”
In order for the OBD monitor system to become ready, the vehicle
should be driven under a variety of normal operating conditions.
These operating conditions may include a mix of highway driving and
stop and go, city type driving, and at least one overnight-off period.
For specific information on getting your vehicle’s OBD monitor
system ready, please consult your vehicle owner’s manual.

2.6 OBD II Definitions

Power-train Control Module (PCM) -- OBD II terminology for the
on-board computer that controls engine and drive train.
Malfunction Indicator Light (MIL) -- Malfunction Indicator Light
(Service Engine Soon, Check Engine) is a term used for the light on
the instrument panel. It is to alert the driver and/or the repair
technician that there is a problem with one or more of vehicle's
systems and may cause emissions to exceed federal standards. If the
MIL illuminates with a steady light, it indicates that a problem has
been detected and the vehicle should be serviced as soon as possible.
Under certain conditions, the dashboard light will blink or flash. This
indicates a severe problem and flashing is intended to discourage
vehicle operation. The vehicle onboard diagnostic system can not turn
the MIL off until necessary repairs are completed or the condition no
longer exists.
DTC -- Diagnostic Trouble Codes (DTC) that identify which section
of the emission control system has malfunctioned.
Enabling Criteria -- Also termed Enabling Conditions. They are the
vehicle-specific events or conditions that must occur within the
engine before the various monitors will set, or run. Some monitors
require the vehicle to follow a prescribed “drive cycle” routine as part

6
of the enabling criteria. Drive cycles vary among vehicles and for
each monitor in any particular vehicle.
OBD II Drive Cycle -- A specific mode of vehicle operation that
provides conditions required to set all the readiness monitors
applicable to the vehicle to the “ready” condition. The purpose of
completing an OBD II drive cycle is to force the vehicle to run its
onboard diagnostics. Some form of a drive cycle needs to be
performed after DTCs have been erased from the PCM’s memory or
after the battery has been disconnected. Running through a vehicle’s
complete drive cycle will “set” the readiness monitors so that future
faults can be detected. Drive cycles vary depending on the vehicle and
the monitor that needs to be reset. For vehicle specific drive cycle,
consult the vehicle’s Owner’s Manual.
Freeze Frame Data -- When an emissions related fault occurs, the
OBD II system not only sets a code but also records a snapshot of the
vehicle operating parameters to help in identifying the problem. This
set of values is referred to as Freeze Frame Data and may include
important engine parameters such as engine RPM, vehicle speed, air
flow, engine load, fuel pressure, fuel trim value, engine coolant
temperature, ignition timing advance, or closed loop status.

7
3. Using the Scan Tool
3.1 Tool Description

1) CONNECTOR -- Connects the scan tool to the vehicle’s Data

Link Connector (DLC).
2) SD Card Slot – Holds the System SD card.
3) LCD DISPLAY -- Indicates test results. TFT color display (320
x 240 dpi).

8
4) FUNCTION BUTTON – Corresponds with “buttons” on
screen for executing commands.
5) ESC BUTTON -- Cancels a selection (or action) from a
menu or returns to the previous screen.

6) HELP BUTTON -- Provides help information and Code

Breaker function.
7) UP SCROLL BUTTON -- Moves up through menu and
submenu items in menu mode. When more than one screen of
data is retrieved, moves up through the current screen to the
previous screens for additional data. When looking up DTC, it is
used to change value of selected character.
8) DOWN SCROLL BUTTON -- Moves down through
menu and submenu items in menu mode. When more than one
screen of data is retrieved, moves down through the current
screen to next screens for additional data. When looking up DTC,
it is used to change value of selected character.

9) LEFT SCROLL BUTTON -- When look up DTC

definitions, moves to previous character and views additional
information on previous screens if DTC definition covers more
than one screen; views previous screen or previous frames of
recorded data. It is also used to view previous trouble code
when viewing DTCs.

10) RIGHT SCROLL BUTTON -- When look up DTC

definitions, moves to next character and view additional
information on next screens if DTC definition covers more than
one screen; views next screen or next frames of recorded data..
It is also used to view next trouble code when viewing DTCs.
11) OK BUTTON -- Confirms a selection (or action) from a
menu.
12) External DC Power Port – Connects the 12 volt power adapter
to power the tool when disconnected from the vehicle.
13) USB CONNECTOR -- Connects the scan tool to the PC for
printing.
9
3.2 Specifications
1) Display: TFT color display (320 x 240 dpi)
2) Operating Temperature: 0 to 60°C (32 to 140 °F)
3) Storage Temperature: -20 to 70°C (-4 to 158 °F)
4) External Power: 12.0 to 18.0 V power provided via vehicle
battery or adapter.
5) Dimensions:
Length Width Height
212 mm (8.35”) 110.5 mm (4.35”) 37.5 mm (1.48”)
6) Weight: 0.28kg(without wire) 0.484kg(with wire)

3.3 Accessories Included

1) User’s Manual -- Instructions on tool operations.
2) CD -- Includes user’s manual, MaxiLink update software, and
etc.
3) OBD2 cable -- Provides power to tool and communicates
between tool and vehicle.
4) USB cable -- Used to upgrade the scan tool, and to print
retrieved data.
5) SD card -- Contains the scan tool’s operation software and
applications.
6) Carry case -- A nylon case to store the scan tool when not in use.

3.4 Keyboard
No solvents such as alcohol are allowed to clean the keypad or display.
Use a mild nonabrasive detergent and a soft cotton cloth. Do not soak
the keypad as the keypad is not waterproof.

3.5 Power
Before using the scan tool, you must provide power to the scan tool.
There are two methods for providing power to the scan tool.
 DC external power adapter.

10
  Cable connection to vehicle.
During vehicle testing, power for the scan tool is usually provided
through the vehicle cable connection. When the scan tool is not
connected to a vehicle, the scan tool can be powered with an AC/DC
external power adapter.
While the scan tool is powered via the vehicle Data Link Connector
(DLC), just follow the steps below to turn on the scan tool:
1) Connect the Cable to scan tool.
2) Find DLC on vehicle.
 A plastic DLC cover may be found for some vehicles and you
need to remove it before plugging the OBD2 cable.
3) Plug the cable to the vehicle’s DLC.

4) Power up the scan tool , and wait for the Main Screen to
appear.(Figure 3.1)

Figure 3.1

3.6 System Setup

The System Setup functions allow you to adjust default settings and
view information about the scan tool.
1) Language: Selects the desired language.
2) Unit of measure: Sets the unit of measure to English or Metric.
3) Beep Set: Turns on/off beep.
4) LCD Test: Checks if the LCD display is working properly.
11
5) Key Test: Checks if the keyboard is working properly.
6) About: Provides information of the scan tool.
 Settings of the unit will remain until change to the existing
settings is made.

To enter the Setup menu

From the Main Screen, use LEFT/RIGHT scroll button to select

Setup, and press the OK button. Following the instructions to do
adjustments and settings could make your diagnosis more
conveniently and easily. (Figure 3.2)

Figure 3.2

Language Setup
 English is the default language.
1) From System Setup screen, use the UP/DOWN scroll button
and LEFT/RIGHT scroll button to select Language, and press
the OK button.

2) Use the UP/DOWN scroll button to select the desired language

and press the OK button to save your selection and return to
previous screen. (Figure 3.3)

12
 Figure 3.3

Unit of Measure
 Metric is the default measurement unit.
1) From System Setup screen, use the LEFT/RIGHT scroll button
to select EN/METRIC unit and press the OK button.

2) From Unit of Measure screen, use the LEFT/RIGHT scroll

button to select the desired unit of measurement. (Figure 3.4 )

Figure 3.4

3) Press the OK button to save your selection and return to previous

menu. Or, press the ESC button to exit without saving.

Beep Set
 The default setting is Beep On.

13
1) From System Setup screen, use the UP/DOWN scroll button
and LEFT/RIGHT scroll button to select Beep and press the
OK button.

2) From Beep Set menu, use the LEFT/RIGHT scroll button to

select ON or OFF to turn on/off the beep. (Figure 3.5)

Figure 3.5

3) Press the OK button to save your selection and return to

previous menu. Or, press the ESC button to exit without saving.

Key Test
The Key Test function checks if the keyboard is working properly.
1) From System Setup screen, use the UP/DOWN scroll button
and LEFT/RIGHT scroll button to select Key Test, and press
the OK button.

2) Press any key to start test. When you press a key, the edge around
corresponding key on the screen should turn to red. Otherwise,
the key is not functioning properly.

3) Double press ESC to return to previous menu.

LCD Test
The LCD Test function checks if the LCD display is working
normally.

14
 1) From System Setup screen, use the UP/DOWN scroll button
and LEFT/RIGHT scroll button to select LCD Test, and press
the OK button.

2) Look for missing spots in the red, green, blue, black and white
LCD display.
3) When completed, press the ESC button to exit.

About
The About function allows viewing of some important information
such as serial number and software version number of the scanner.
1) From System Setup screen, use the UP/DOWN scroll button
and LEFT/RIGHT scroll button to select About and press the
OK button; wait for the About screen to appear.

2) View tool information on screen. (Figure 3.6) Press the ESC

button to exit without saving.

Figure 3.6

3.7 Vehicle Coverage

On the basis of all OBD II compliant vehicles, including those
equipped with universal protocol -- Control Area Network (CAN),
MaxiDiag Elite Series Scanner expands vehicle system coverage and
offers more diagnostic power to the vehicle technicians. Featuring
expanded global vehicle coverage, the scan tool offers technicians a

15
 significant improvement on model years covered by supported
manufactures. In addition to adding new vehicle coverage through
2010/2011, we’ve also worked backwards to include non-OBDII
vehicles, which can be diagnosed by setting up with optional OBDI
adaptors.
For a complete listing of all the added vehicle coverage, download a
copy of the official MaxiDiag Elite Software Release Note.

3.8 Product Troubleshooting

Vehicle Linking Error
A communication error occurs if the scan tool fails to communicate
with the vehicle’s ECU (Electronic Control Unit). You need to do
the following to check up:
 Verify that the ignition is ON.
 Check if the scan tool’s connector is securely
connected to the vehicle’s DLC.
 Turn the ignition off and wait for about 10 seconds. Turn the
ignition back to on and continue the testing.
 Verify the control module is not defective.
Operating Error
If the scan tool freezes, then an exception occurs or the vehicle’s
ECU (Electronic Control Unit) is too slow to respond to requests.
You need to do the following to reset the tool:
 Reset the scan tool.
 Turn the ignition off and wait for about 10 seconds. Turn the
ignition back to on and continue the testing.

Scan tool doesn’t power up

If the scan tool won’t power up or operates incorrectly in any other
way, you need to do the following to check up:
 Check if the scan tool’s connector is securely connected to the
vehicle’s DLC;

16
 Check if the DLC pins are bent or broken. Clean the DLC pins if
necessary.
 Check vehicle battery to make sure it is still good with at least 8.0
volts.

17
4. Playback Data
The Playback Data function allows viewing data from last test
recorded by the scan tool.

NOTE: The amount of files that can be saved depends on the

space available in the SD card.

4.1 Reviewing Data

1) Use the LEFT/RIGHT scroll button to select Playback from
Main Screen (Figure 3.1), and press the OK button. Wait for
the Scan screen to appear. (Figure 4.1)

2) Use the UP/DOWN scroll button to select the desired item from
Scan screen, and press the OK button.

Scan
1. UITrouble
/scan/MAKE/USA/FORD/
2. UIDatastream: complete list
/scan/make/EOBD/
3. UIFreeze
/scan/make/USA/
Delete Delete All

Figure 4.1

 If no data from previously tested vehicle is recorded, a message

“No data available!” shows on the screen.

3) Review selected data on screen. (Figure 4.2 )

18
 Vehicle Specification
Vehicle: Mustang
Engine Type: Other
Capacity: 3.8L
Transmission: Manual
Fuel Type: Gasoline
Emission Level: Federal Emission
VIN:1FAFP40462F100819
PrefSuf:2R3APB VersionID:4612
Print

Figure 4.2

4.2 Deleting Data

By selecting Delete on the Scan screen, you are allowed to erase the
selected data on the scan tool. Review the recordings thoroughly
before erasing. You could also erase all recordings by select Delete
All.

NOTE: Don’t use Delete All unless you are definitely sure what
you are going to proceed.

4.3 Printing Data

Print option allows you to print the recorded files to your computer
and then to the printer.
For more details, please refer to chapter 7. Print Data.

19
5. Diagnostics
NOTE: The screens shown below in this chapter are examples.
The screens actually appear vary by vehicle.

5.1 Entering Vehicle Information

Before using the scan tool to diagnose, you must input the vehicle
information. There are generally three ways to input the vehicle
information.
 Vehicle information manual acquisition.
 VIN code automatic acquisition.
 VIN code manual acquisition.
The way to enter diagnostic procedure depends on vehicle being
tested.

5.1.1 Vehicle Information Manual Acquisition

Follow these steps to enter the vehicle information and begin
diagnostics. (Taking Ford as an example)
1) Turn on the scan tool and wait for the Main Screen to appear.
2) Select Scan icon in the Main Screen (Figure 3.1) and wait for
the vehicle manufacturer screen. Choose the correct vehicle
make.

Figure 5.1

20
 Figure 5.2

3) Step by step, select the right options for your vehicle according
to each screen that appears.

DAS Vehicle

1. Start New Session 1. All other

2. Manual Vehicle Entry

Figure 5.3 Figure 5.4

Traction Assist Transmission

1. Not Equipped 1. ASM(Auto Shift Manual)

2. Equipped 2. Powershift
3. Manual
4. Automatic
5. DPS6

Figure 5.5 Figure 5.6

4) Do this until the complete vehicle information is entered. Then

the scan tool will ask your confirmation.

21
 Vehicle Specification
Vehicle: Mustang
Engine Type: Other
Capacity: 3.8L
Transmission: Manual
Fuel Type: Gasoline
Emission Level: Federal Emission
Is this correct?
Yes no

Figure 5.7

5.1.2 VIN Code Automatic Acquisition

Some vehicles could identify the VIN code intelligently, saving
customer’s time to input complex information. (Taking Renault as an
example)

Figure 5.8

RENAULT

1. VIN acquisition

Figure 5.9

22
 VIN acquisition

1.VIN CODE automatic acquisition

2.VIN CODE manual acquisition
3.Vehicle type manual acquisition

Figure 5.10
In this mode, the scan tool will communicate with the vehicle and
read off the VIN code automatically. It will ask for your
confirmation about the VIN code if ECU response received. If no
response from the ECU, it will turn to manual mode. (Please see
VIN Code Manual Acquisition)

5.1.3 VIN Code Manual Acquisition

For some vehicles, both selecting the options manually and acquiring
the VIN are available for you to enter the vehicle information.
(Taking Benz as an example)

Figure 5.11

In the Benz Cars menu, choose the item “2. Select by entering
VIN” and you can enter the VIN code directly.

23
 Cars
1.Vehicle record and abbreviation
2.Select by entering VIN
3.All model series
4.A-Class
5.B-Class
6.C-Class/CLK
7.E-Class/CLS

Figure 5.12

Select by entering VIN

If the chassis number does not

Match the vehicle, enter VIN as a
17-digit code.
Example:WDBNG70J02A123456

Finish Show Esc

Figure 5.13

When you choose to enter VIN directly, a pop-up soft keyboard is

used to input VIN code. (Figure 5.14)

To pop up the keyboard, press the Function button corresponding to

Show. Use UP/DOWN scroll button and LEFT/RIGHT scroll
button to select digit and character, and then press OK button to
confirm. Use Backspace button to delete the previous digit or
character. When finished, press the Function button corresponding to
Finish to proceed. The scan tool will identify the VIN code and turn
to diagnostic procedure.

24
 Figure 5.14

5.2 Diagnostic Test

After you have entered the correct vehicle information, the
diagnostic testing selection will display as below:

Select An Option

1. Auto Scan
2. Control Unit
3. Vehicle Information

Figure 5.15

5.2.1 Auto Scan

Depending on the scan tool model, Auto Scan function will carry
out an overall scan to check the status of all systems or four systems
(engine, transmission, airbag and ABS) on the vehicle being tested.
Selecting Auto Scan will lead to retrieve the trouble codes in each
system of the vehicle one by one. It will take a few minutes to
display.
Use the UP/DOWN scroll button to select Auto Scan from Main
Groups menu (Figure 5.15), and press the OK button.

25
 100% Auto Scan

PCM- Powertrain Fault 1

Control Module

Quick Erase Save Display DTC

Figure 5.16
User is allowed to check the details of each system, quickly erase
DTC, save the data, and display DTC from the Auto Scan menu
screen. To select the options on the bottom, simply press the
corresponding function button.

 Save –You can save the Auto Scan information as “Vehicle

Record” so that you will not need to follow the vehicle selection
process again on the same vehicle in later tests. For detailed
instructions, please refer to 5.2.4 Save and retrieve files.

 Quick Erase – By selecting this option, the scan tool will erase
all displaying DTCs and once again read the data and check the
latest status of the system. If the system did not repair, the
trouble codes will keep on displaying.

 Display DTC – This option allows you to read DTC definitions

in the highlighted system. If more than one fault is detected in a
system, the scan tool will display an option list for you to view
different kind of DTCs or freeze frames.

Select Option

1.CMDTCs(Continuous memory
diagnostic trouble codes)
2.Freeze Frame-Mode 2
3.pending

Figure 5.17
26
 In Auto Scan screen (Figure 5.16), pressing OK button will turn to
diagnostic operation. For more details, refer to 5.3 Diagnostic
Operation.

To exit the Auto Scan option, press ESC button. The scan tool will
display a message “Are you sure to quit?” to ask for your
confirmation. Select Yes to quit, and select No to cancel command.

5.2.2 Control Unit

Control Unit function will list down all the systems that might be
available on the vehicle for you to select to test. Select a system to
display the function menu and start testing.

System Menu

1. ABS-Anti-Lock Brake/ Traction

Control Module
2. ACM-Audio Control Module
3. BEM-Body Electronic Module
4. FDIM-Front Display Interface
Module
5. HIM-HAVC Integrated Module
6. IPC-Instrument Panel Control

Figure 5.18

NOTE: The actual systems displayed in the System Menu

screen may be different from Figure 5.18 due to various vehicle
configurations.

5.2.3 Vehicle Information

Vehicle Information function allows you to view vehicle-specific
information for Specifications, System Type and other Identification.

27
 Vehicle Specification
Vehicle: Mustang
Engine Type: Other
Capacity: 3.8L
Transmission: Manual
Fuel Type: Gasoline
Emission Level: Federal Emission
VIN:1FAFP40462F100819
PrefSuf:2R3APB VersionID:4612
OK

Figure 5.19

5.2.4 Save and Retrieve Files

Save and Retrieve Files function will save the detected vehicle
information. You can directly get the vehicle information next time.

Please follow the instructions above to finish the Auto Scan process
(Figure 5.15), and press the Function button corresponding to Save,
and name the record on the Save Vehicle Record screen.

Save Vehicle Record

Input vehicle name:

Maximum length is 25 characters..

Finish Show Esc

Figure 5.20

To enter the diagnostic functions through the vehicle record option in

future, please follow these steps:

 Select Vehicle Data Recorder from the DAS menu.

28
 DAS

1. Start New Session

2. Manual Vehicle Entry
3. Vehicle Data Recorder

Figure 5.21

 Click on the vehicle file you desired to enter the diagnostic

menu directly.

Vehicle Data Record

1. Ford1
2. Ford2

Figure 5.22

5.3 Diagnostic Operation

This function allows you to read and clear diagnostic trouble codes
(DTCs), read and save live data. (Taking Ford as an example)

5.3.1 Read Codes

The Read Codes procedure varies for each vehicle being tested. This
section includes the following Read Codes procedures.

In the Function Menu screen (Figure 5.23), select Read Codes.

This will display the Read Codes menu screen. (Figure 5.24)

29
 Function Menu

1. Read Codes
2. Erase Codes
3. Live Data

Figure 5.23

Read Codes

1. KOEO On Demand Self-test

2. KOER On Demand Self-test
3. Retrieve CMDTCs(Continuous
Memory Diagnostic Trouble
Codes)

Figure 5.24

In the Read Codes menu, select one of the options to proceed. The
screen will show as below.

Select options

1. CMDTCs
2. Freeze Frame-MODE2
3. Pending.

Figure 5.25

Select one of the DTC options to view detailed diagnostic trouble

code information.

30
 CMDTCs
P0046
Battery voltage high
Status-60(No additional fault
symptom available for this DTC).
P0098
Intake air temperature sensor 2
Circuit high input
Save

Figure 5.26

You can save the code results for later review by selecting Save
option on the bottom. When you finished viewing the DTCs, press
the ESC button to return to previous screen.

5.3.2 Erase Codes

After reading and / or reviewing the diagnostic trouble codes, take
the following steps to erase codes from the vehicle. If Erase Codes
is not an available menu option, consult the manufacturer’s service
manual for the correct “clear code” method.
NOTE: This Erase Codes function clears the DTCs from the
selected ECU or provides instructions for how to manually clear
the codes from the ECU.
NOTE: Before performing this procedure, make sure the vehicle’s
ignition key is in the On (Run) position with the engine off.

To Erase DTCs, please follow these steps:

1. With the Function Menu screen displayed (Figure 5.23), click
on Erase Codes. The scan tool displays an instruction message.
2. Follow the instructions on each screen that appears until the
procedure is complete.
3. When finished, press any key to exit.
4. Use Read Codes function to check the codes again to see if
DTCs have been erased successfully. If any codes remain, it
indicates that the vehicle needs maintenance. Please repeat the
Erase Codes steps after repairing the vehicle.
31
5.3.3 Live Data
Live Data function enables you to view the “real-time” live data,
including the information of values (volts, rpm, temperature, speed
etc.) and system status information (open loop, closed loop, fuel
system, etc.) generated by vehicle sensors, switches and actuators.

NOTE: If the vehicle must be driven in order to perform a

troubleshooting procedure, ALWAYS have a second person help
you. One person should drive the vehicle while the other person
observes the Scan Tool data. It is dangerous to drive and operate
the Scan Tool at the same time because a serious traffic accident
might be caused.

1) To view live data, use the UP/DOWN scroll button to select

Live Data from Function Menu screen (Figure 5.27), and press
OK button. The screen will show as below.

………… ..Live Data

 MFF_RPM(Engine RPM) 1

□ MFF_SOAk(Engine Off Soak Time

Prior to Misfire)
 VEHICLE SPEED SENSOR 2

Select All Select Clear All

Figure 5.27

 The number to the right of selected item indicates sequence of

this item.
 If you want to select the item, press Select button.
 To select all the items on the screen, press Select All button. To
clear all the selected items on the screen, press Clear All button.

2) Press the OK button to view the information.

32
 Live Data

MFF_RPM(Engine RPM) 837 RPM

VEHICLE SPEED SENSOR 0 km/h

Pause ︱ one Graphic︱ Save

Figure 5.28
The three keyboard function buttons work as below.

[One Graphic]: To view the live data waveform.

[Save]: Save the live data.

[Pause]: Suspend viewing and stop saving live data.

3) Press the Function button corresponding to One Graphic. The

screen will show the live data waveform as Figure 5.29.

Figure 5.29

4) Press the Function button corresponding to Two Graphic, the

screen will show two graphs as Figure 5.30.

33
 Figure 5.30

5) Press the Function button corresponding to Merge Graph, the

above two graphs will merge together as Figure 5.31.

Figure 5.31

NOTE: Merge Graph can be used to compare two related

parameters in graphic mode. It is especially convenient that you
could select two interacted parameter to merge and see their
relationship.

6) Select Text to return to the view the live data in text form

7) Select Save to record retrieved live data and graphs.

NOTE: The scan tool can only playback text data even though
the data is saved in graphic mode. Since what you are viewing
is “real time” Live Data, the data changes as the vehicle’s
operating conditions change.

34
 When there is not enough memory space, a warning message
prompting to delete previously recorded data.

Save Failure

Memory space not enough!

Erase previously recorded
Data?

Yes No

Figure 5.32

 If you wish to delete the data, select Yes and save currently
retrieved data in the SD card.
 If you do not wish to delete the data, select No to return to
previous screen.
 Select Pause to suspend recording. You could resume the
recording process again by selecting Continue.
 You may review the saved data in Playback function.
 Press ESC button to exit.

35
6. OBDII Diagnostics
The OBD II Diagnostics function is a fast-access option that allows
you to carry out a quick test on the engine system of OBD II
vehicles.
When more than one vehicle control module is detected by the
scan tool, you will be prompted to select the module where the
data may be retrieved. The most often to be selected are the
Power-train Control Module [PCM] and Transmission Control
Module [TCM].
CAUTION: Don’t connect or disconnect any test equipment with
ignition on or engine running.
1） Turn the ignition off.
2） Locate the vehicle’s 16-pin Data Link Connector (DLC).
3） Plug the scan tool cable connector into the vehicle’s DLC.
4） Turn the ignition on. Engine can be off or running.
5） Turn on the scan tool. Select OBDII from the Main Screen.
(Figure 3.1)
6） Press the OK button to wait for the Menu to appear. A sequence
of messages displaying the OBDII protocols will be observed
on the display until the vehicle protocol is detected.

 If the scan tool fails to communicate with the vehicle’s ECU

(Engine Control Unit) more than three times, a “LINKING
ERROR!” message shows up on the display.
 Verify that the ignition is ON.
 Check if the scan tool’s OBD II connector is securely
connected to the vehicle’s DLC.
 Verify that the vehicle is OBD2 compliant.
 Turn the ignition off and wait for about 10 seconds. Turn the
ignition back to on and repeat the procedure from step 5.

 If the “LINKING ERROR” message does not go away, then

there might be problems for the scan tool to communicate with

36
 the vehicle. Contact your local distributor or the
manufacturer’s customer service department for assistance.
7） View a summary of system status (MIL status, DTC counts,
Monitor status) on screen. (Figure 6.1 ) Press ESC button for
Diagnostic Menu (Figure 6.3) to come up.

System Status

MIL Status OFF

Codes Found 0
Monitors N/A 8
Monitors OK 2
Monitors INC 0

Save OK

Figure 6.1
 If more than one module is detected, you will be prompted to
select a module before testing. (Figure 6.2 )

Control Module

Module $10
Module $A4

Figure 6.2
 Use the UP/DOWN scroll button to select a module and press
the OK button.

6.1 Read Codes

 Reading Codes can be done with the key on engine off (KOEO)
or with the key on engine running (KOER).
 Stored Codes are also known as “hard codes”, which are fault
codes, or trouble codes that have been stored in the vehicle
computer memory because the faults have reoccurred for
37
 more than a specified amount of key-cycles. These codes will
cause the control module to illuminate the malfunction
indicator light (MIL) when emission-related fault occurs.
 Pending Codes are also referred to as “maturing codes” or
“continuous monitor codes”. They indicate problems that the
control module has detected during the current or last driving
cycle but are not considered serious yet. Pending Codes will
not turn on the malfunction indicator lamp (MIL). If the fault
does not occur within a certain number of warm-up cycles, the
code clears from memory.
 Permanent Codes are DTCs that are "confirmed" and are
retained in the non-volatile memory of the computer until the
appropriate monitor for each DTC has determined that the
malfunction is no longer present and is not commanding the
MIL on. Permanent DTC shall be stored in non-volatile
memory and may not be erased by any diagnostic services or
by disconnecting power to ECU.
1) Use UP/DOWN scroll button to select Read Codes from
Diagnostic Menu and press OK button. (Figure 6.3 )

Diagnostic Menu
1.System Status
2.Read Codes
3.Erase Codes
4.Live Data
5.Freeze Frame
6.I/M Readiness
7.O2 Monitor Test
8.On-Board Monitor Test

Figure 6.3
2) Use the UP/DOWN scroll button to select Stored Codes,
Pending Codes or Permanent Codes from the Read Codes
menu and press the OK button. (Figure 6.4 )

38
 Read Codes

1.Stored Codes
2.Pending Codes
3.Permanent Codes

Figure 6.4

 If there is not any Diagnostic Trouble Code, the display indicates

“No (pending) codes are stored in the module!” Wait a few
seconds or press any key to return to previous screen.
NOTE: Permanent Codes function is available for merely
vehicles supporting the CAN protocols.
3) View DTCs and their definitions on screen.

4) If more than one DTC is found, use the UP/DOWN scroll

button to check all the codes.
 If retrieved DTCs contain any manufacturer specific or enhanced
codes, a “Manufacturer specific codes are found! Press any key
to select vehicle make!” message comes up prompting you to
select vehicle manufacturer to view DTC definitions. Use
UP/DOWN scroll button to select manufacturer and then press
OK button to confirm.

Vehicle Manufacturer

BUICK
BMW
CADILLAC
CHEVROLET
CHRYSLER
FORD

Figure 6.5

39
  If the manufacturer of your vehicle is not listed, use the
UP/DOWN scroll button to select Other and press the OK
button.

6.2 Erase Codes

CAUTION: Erasing the Diagnostic Trouble Codes may allow the
scan tool to delete not only the codes from the vehicle’s on-board
computer, but also “Freeze Frame” data and manufacturer
specific enhanced data. Further, the I/M Readiness Monitor Status
for all vehicle monitors is reset to Not Ready or Not Complete
status. Do not erase the codes before the system has been checked
completely by a technician.
NOTE: Erasing codes does not mean that trouble codes in
ECU have been eliminated completely. As long as there is
fault with the vehicle, the trouble codes keeps on presenting.
 This function is performed with key on engine off (KOEO). Do
not start the engine.
1) Use the UP/DOWN scroll buttons to select Erase Codes from
Diagnostics Menu and press the OK button. (Figure 5.3)

2) After you have pressed OK button, a message will come up

asking you to check the ignition and engine status. (Figure 6.6)

Erase Codes

Ignition on and engine stopped?

Yes No .

Figure 6.6
 If you do not want to proceed with erasing codes, press ESC
button or select NO to exit and return to previous screen.

40
  If you press Yes function button or OK button, a warning
message will come up asking your confirmation. (Figure 6.7)
Erase Codes

DTCs and Freeze Data will be lost

Do you wish to continue?

Yes No .

Figure 6.7
3) Press the OK button to confirm.
 If the codes are cleared successfully, an “Erase Done!”
confirmation message shows on the display.( Figure 6.8)

Erase Codes

Erase Done!

Press any key to continue .

Figure 6.8

 If the codes are not cleared, then an “Erase Failure. Turn Key
on with Engine off!” message appears. (Figure 6.9)

Erase Codes

Erase Failure.
Turn Key on with
Engine Off!

Press any key to continue

Figure 6.9

41
 4) Press any button to return to Diagnostic Menu.

6.3 Live Data

In this function, you can not only read the live data but also record
data for later review.

Viewing Data

The View Data function allows viewing of live or real time PID
data of vehicle’s computer module(s).

1) To view live data, use the UP/DOWN scroll button to select Live
Data from Diagnostic Menu and press the OK button. (Figure
6.3)

2) Wait a few seconds while the scan tool validates the PID MAP.
(Figure 6.10)

Live Data

Reading PID.01
- Please Wait -

Figure 6.10

A. Viewing Complete List

1) To view complete set of data, use UP/DOWN scroll button to

select Complete List from Live Data menu and press the OK
button. (Figure 6.11)

42
 …………………Live Data .
1. Complete List
2. Custom List

Figure 6.11

2) View live PIDs on the screen. Use the UP/DOWN scroll button
for more PIDs if additional information is available on more than
one page.( Figure 6.12)

Complete List
Numbers of DTCs 0
Fuel system 1 status OL
Fuel system 2 status --
Calculated load value 0.0 %
0
Engine coolant -40 C
temperature
Pause Graphics Save

Figure 6.12

 If the “Graphics” on the bottom appears when a PID is

highlighted, graphic information is available. Select
Graphics to view graph. (Figure 6.13). PID name, current
value, maximum and minimum values are displayed on the
screen.

43
 Figure 6.13

 If the “Merge Graph” on the bottom appears when a PID is

selected to view, merged graph information is available.
(Figure 6.14)

NOTE: Merge Graph can be used to compare two related

parameters in graphic mode, which is especially convenient in
the Custom List option where you could select two interacted
parameter to merge and see their relationship.

Figure 6.14

 Select Text to return to text viewing of PID data.

 Select Save to record retrieved live data and PID graphs.

 Select Pause to suspend viewing. You could resume the
viewing process again by selecting Start.
44
3) Press the ESC button to return to previous menu.

B. Viewing Custom List

1) To view customized PID data, use the UP/DOWN scroll button

to select Custom List from Live Data menu and press the OK
button. (Figure 6.11)

2) Use the UP/DOWN scroll button to move up and down to the

desired items and click Select button to confirm. The selected
parameters are marked with solid squares. (Figure 6.15)

………… ..Custom List

 Numbers of DTCs 1
 Fuel system 1 status 2
 Fuel system 2 status
 Calculated load value
 Engine coolant temp
Select All Clear Clear all

Figure 6.15

 The number to the right of selected item indicates sequence

of this item.

 If you want to deselect the item, press Clear button.

 To select all the items on the screen, press Select All button.
To clear all the selected items on the screen, press Clear All
button.

3) Press the OK button to view selected PIDs on screen.

45
 Custom List
Numbers of DTCs 0
Fuel system 1 status OL

Pause Graphics Save

Figure 6.16

4) Press the OK button to view selected PIDs on screen.

Recording Data

The Record Data function allows recording vehicle modules’

Parameter Identification (PID) data to help diagnose
intermittent vehicle problems. You could save data files to the
SD card and then use the Playback function to view the saved
files.
NOTE: The length of time for each frame varies per vehicle.
Generally, one frame of data is about 1/4 second, or 4 frames per
second.
1) To record live data, with the live data screen displaying, select
Save on the bottom. The scan tool will start timing to record
retrieved live data and PID graphs.

 If you record live data under text mode, following screen

shows::

Complete List
Numbers of DTCs 0
Fuel system 1 status OL
Fuel system 2 status --
Calculated load value 0.0 %
0
Engine coolant -40 C
temperature
Pause Graphics Saving 94

Figure 6.17
46
 If you record live data under graph mode, following screen
shows:

Figure 6.18

NOTE: The scan tool can only playback text data even though
the data is saved in graphic mode.

2) When there is not enough memory space, a warning message

prompting to delete previously recorded data.

Save Failure

Memory space not enough!

Erase previously recorded
Data?

Yes No

Figure 6.19

 If you wish to delete the data, select Yes and save currently
retrieved data in the SD card.
 If you do not wish to delete the data, select No to return to
previous screen.
3) Select Pause to suspend recording. You could resume the
recording process again by selecting Start.

47
 4) You may review the saved data in Playback function.
5) Press ESC button to exit.

6.4 Freeze Frame

Freeze Frame Data allows the technician to view the vehicle’s
operating parameters at the moment a DTC (Diagnostic Trouble
Code) is detected. For example, the parameters may include
engine speed (RPM), engine coolant temperature (ECT), or
vehicle speed sensor (VSS) etc. This information will aid the
technician by allowing the parameters to be duplicated for
diagnostic and repair purposes.
1) To view freeze frame data, use the UP/DOWN scroll button to
select Freeze Frame from Diagnostic Menu and press the OK
button. (Figure 6.3 )

2) Wait a few seconds while the scan tool validates the PID MAP.

3) If retrieved information covers more than one screen, use the

DOWN scroll button, as necessary, until all the data have been
shown up. (Figure 6.20)

Freeze Frame
DTC that caused required P0193
freeze frame data storage
Fuel system 1 status OL
Fuel system 2 status --
Calculated load value 0.0 %
0
Engine coolant -40 C
temperature

Save

Figure 6.20

 If there is no available freeze frame data, an advisory message

“No freeze frame data stored!” shows on the display.

48
 4) Select Save to record freeze frame. A confirming message “Save
success!” shows on the display and scan tool return to previous
menu.

5) If you don’t want to save the freeze frame data, press ESC
button to return to previous screen.

6.5 Retrieving I/M Readiness Status

I/M Readiness function is used to check the operations of the
Emission System on OBD2 compliant vehicles. It is an excellent
function to use prior to having a vehicle inspected for
compliance to a state emissions program.
CAUTION - By clearing trouble codes you also clear the readiness
status for the individual emission system readiness tests. In order
to reset these monitors, the vehicle must be driven through a
complete drive cycle with no trouble codes in memory. Times for
reset vary depending on vehicle.
Some latest vehicle models may support two types of I/M
Readiness tests:
A. Since DTCs Cleared - indicates status of the monitors since the
DTCs are erased.
B. This Drive Cycle - indicates status of monitors since the
beginning of the current drive cycle.
An I/M Readiness Status result of “NO” does not necessarily
indicate that the vehicle being tested will fail the state I/M
inspection. For some states, one or more such monitors may be
allowed to be “Not Ready” to pass the emissions inspection.

 “OK” -- Indicates that a particular monitor being checked has

completed its diagnostic testing.
 “INC” -- Indicates that a particular monitor being checked has
not completed its diagnostic testing.
 “N/A” -- The monitor is not supported on that vehicle.

49
1) Use the UP/DOWN scroll button to select I/M Readiness from
Diagnostic Menu and press OK button. (Figure 6.3)
2) Wait a few seconds while the scan tool validates the PID MAP.

3) If the vehicle supports both types of tests, then both types will be
shown on the screen for selection. (Figure 6.21)

…………… I/M Readiness .

1.Since DTCs Cleared

2.This Drive Cycle

Figure 6.21

4) Use the UP/DOWN scroll button, as necessary, to view the status

of the MIL light (“ON” or “OFF) and the following monitors:

For spark ignition engines:

 MIS -- Misfire Monitor
 FUEL -- Fuel System Monitor
 CCM -- Comprehensive Component Monitor
 EGR – EGR System Monitor
 O2S -- O2 Sensors Monitor
 CAT -- Catalyst Monitor
 EVAP -- Evaporative System Monitor
 HTR -- O2 Sensor Heater Monitor
 AIR -- Secondary Air Monitor
 HCAT -- Heated Catalyst Monitor

For compression ignition engines:

 MIS -- Misfire Monitor

50
  FUEL -- Fuel System Monitor
 CCM -- Comprehensive Component Monitor
 EGR – EGR System Monitor
 HCCAT -- NMHC Catalyst Monitor
 NCAT -- NOx Aftertreatment Monitor
 BP -- Boost Pressure System Monitor
 EGS -- Exhaust Gas Sensor Monitor
 PM -- PM Filter Monitor

Since DTCs cleared

MIL Status OFF
Misfire Monitoring N/A
Fuel system monitoring OK
Comprehensive OK
component monitoring
Catalyst monitoring N/A
Heated catalyst monitor N/A

Figure 6.22

5) If the vehicle supports readiness test of “This Drive Cycle”, a

screen of the following displays: (Figure 6.23)

This Drive Cycle

MIL Status OFF

Misfire Monitoring N/A

Fuel system monitoring OK

Comprehensive OK
component monitoring

Figure 6.23
Catalyst monitoring N/A

Heated catalyst monitor N/A

6) Use the UP/DOWN scroll button for more PIDs if additional
information is available on more than one page. Or use the
LEFT/RIGHT scroll button to view PIDs in the previous/next
page.

51
 7) Press the ESC button to return to Diagnostic Menu.

6.6 O2 Monitor Test

OBD2 regulations set by SAE require that relevant vehicles
monitor and tests on the oxygen (O2) sensors to identify problems
related to fuel efficiency and vehicle emissions. These tests are not
on-demand tests and they are done automatically when engine
operating conditions are within specified limits. These test results
are saved in the on-board computer's memory.
The O2 Monitor Test function allows retrieval and viewing of O2
sensor monitor test results for the most recently performed tests
from the vehicle's on-board computer.
The O2 Monitor Test function is not supported by vehicles which
communicate using a controller area network (CAN). For O2
Monitor Test results of CAN-equipped vehicles, see chapter
“On-Board Mon. Test”.
1) Use the UP/DOWN scroll button to select O2 Monitor Test
from Diagnostic Menu and press OK button. (Figure 6.3)

2) Wait a few seconds while the scan tool validates the PID MAP.

3) Use the UP/DOWN scroll button to select O2 sensor from O2

Monitor Test menu and press OK button. (Figure 6.24)

.......... ..O2 Monitor Test …

1.O2 Bank1 Sensor1

2.O2 Bank1 Sensor2
3.O2 Bank2 Sensor1
4.O2 Bank2 Sensor2

Figure 6.24

 If the vehicle does not support the mode, an advisory message

will be displayed on the screen. (Figure 6.25)

52
 …………….O2 Monitor Test…………..

The selected mode is

not supported!

Press any key to continue .

Figure 6.25

4) View test results of selected O2 sensor. (Figure 6.26)

… ……… .O2 Bank1 Sensor2 .

Rich-Lean Threshd V
Lean-Rich Threshd V
Low for Switch (V)
High for Switch (V)
Rich-Lean Threshd S
Lean-Rich Threshd S

Figure 6.26

5) Use the UP/DOWN scroll button to view more screens of data if

additional information is available in more than one page.
6) Press the ESC button to return to the previous menu.

6.7 On-Board Monitor Test

The On-Board Monitor Test is useful after servicing or after
erasing a vehicle’s control module memory. The On-Board
Monitor Test for non-CAN-equipped vehicles retrieves and
displays test results for emission-related power train components
and systems that are not continuously monitored. The On-Board
Monitor Test for CAN-equipped vehicles retrieves and displays
test results for emission-related power train components and
systems that are and are not continuously monitored. Test and
components IDs are determined by the vehicle manufacturer.
In this test, there are typically a minimum value, a maximum value,
and a current value for each monitor. By comparing the current value
53
with the minimum and maximum value, the scan tool will determine
if it is OK.
1) Use the UP/DOWN scroll button to select On-Board Monitor
Test from Diagnostic Menu and press the OK button. (Figure
6.3)

2) Wait a few seconds while the scan tool validates the PID MAP.

3) The scan tool will prompt you to select the vehicle make. (If you
have selected the vehicle before, the Vehicle Manufacturer
screen would not appear again)

Vehicle Manufacturer

BUICK
BMW
CADILLAC
CHRYSLER
FORD
GM

Figure 6.27
4) After you select the vehicle manufacturer, the scan tool shows
the On-Board Monitors tests for specific monitoring systems.

5) From On-Board Monitor Test menu, use the UP/DOWN scroll

button to select a test to view and press the OK button. (Figure
6.28)

On-Board Monitor Test

1. Test $01 Data

2. Test $03 Data
3. Test $10 Data
4. Test $21 Data
5. Test $22 Data
6. Test $25 Data

Figure 6.28

54
  If the vehicle under test does not support the mode, an
advisory message will be displayed on the screen. (Figure
6.29)

On-Board Monitor Test

The selected mode is

not supported

Press any key to continue

Figure 6.29
 For CAN-equipped vehicles, test selections can be as below:

On-Board Monitor Test ..

1. EGR Monitor
2. Mis-Fire Monitor Data
3. Mis-Fire Cylinder 1 Data
4. Mis-Fire Cylinder 2 Data
5. Mis-Fire Cylinder 3 Data
6. Mis-Fire Cylinder 4 Data

Figure 6.30
6) Use the UP/DOWN scroll button to select the desired monitor
from On-Board Monitor Test menu and press the OK button.
7) View test data on screen.

Test $01 Data

ID 11
Module $10
Test Value 0400
Min Limit 0200
Max Limit ----
Status OK

Figure 6.31

55
  For CAN-equipped vehicles, test results displayed can be as
below:

Flow Test
ID 11
Module $10
Test Value 0.10 %
Min Limit 0.00 %
Max Limit 95.0 %
Status OK

Figure 6.32

8) Press ESC button to return to the previous menus.

6.8 Component Test

The Component Test function allows initiating a leak test for the
vehicle's EVAP system. The scan tool itself does not perform the
leak test, but commands the vehicle's on-board computer to start
the test. Different vehicle manufacturers might have different
criteria and methods for stopping the test once it has been started.
Before starting the Component Test, refer to the vehicle service
manual for instructions to stop the test.
1) Use the UP/DOWN scroll button to select Component Test from
Diagnostic Menu and press the OK button. (Figure 6.3)

2) Wait for the scan tool to display the Component Test menu.

Component Test

1.EVAP Sys. Leak Test

Figure 6.33

56
 3) If the test has been initiated by the vehicle, a confirmation
message will be displayed on the screen.

Component Test

Command Sent!

Press any key to continue

Figure 6.34

 Some vehicles do not allow scan tools to control vehicle

systems or components. If the vehicle under test does not
support the EVAP Leak Test, an advisory message is
displayed on the screen.

.............Component Test

The selected mode is

not supported

Press any key to continue

Figure 6.35

4) Wait a few seconds or press any key to return to previous screen.

6.9 Viewing Vehicle Information

The Vehicle Info. function enables retrieval of Vehicle
Identification No. (VIN), Calibration ID Nos. (CINs),
Calibration Verification Nos. (CVNs) and In-use Performance
Tracking on 2000 and newer vehicles that support Mode 9.
1) Use UP/DOWN scroll button to select Vehicle Info. from the
Diagnostic Menu and press OK button. (Figure 6.3)

57
2) An advisory message comes up to remind you. Wait a few
seconds or press any key to continue.

Vehicle Info.

Turn key on
with engine off !

Press any key to continue

Figure 6.36

3) Wait for the scan tool to display the Vehicle Info. menu.

Vehicle Info.

1.Vehicle ID Number
2.Caibration ID
3.Cal. Verf. Number

Figure 6.37
 If the vehicle does not support this mode, a message shows on
the display warning that the mode is not supported.
4) From Vehicle Info. menu, use the UP/DOWN scroll button to
select an available item to view and press the OK button.
5) View retrieved vehicle information on screen.

58
 Vehicle ID Number

VIN 1FAFP40462F100819

Esc

Figure 6.38

6) Press the ESC button to return previous menu

6.10 Modules Present

The Modules Present function allows viewing of the module IDs
and communication protocols for OBD2 modules in the vehicle.
1) Use the UP/DOWN scroll button to select Modules Present
from Diagnostic Menu and press OK button. (Figure 6.3)

2) View modules present with their IDs and communication

protocols.

Modules Present

Protocol ID
SAE J1850 PWM $10

Save

Figure 6.39

3) Select Save to save the modules data and return to previous

menu. Or press ESC button to exit.

59
6.11 DTC Lookup
The DTC Lookup function allows user to search definitions of
DTC stored in built-in DTC library.
1) Use the UP/DOWN scroll button to select DTC Lookup from
Diagnostic Menu and press OK button. (Figure 6.3)

2) Wait for the scan tool to display the DTC Lookup screen.

DTC Lookup

Only PCBU can be the first letter

to be put in. Only 0~9,a~f for the
rest letters...

Finish Show Esc

Figure 6.40

3) Select Show and a soft keyboard will pop up. Use

LEFT/RIGHT button and UP/DOWN button to move to the
desired character, then press OK button to confirm.

4) After you input the DTC code, select Finish and the scan tool
will display this code’s definition on screen.

Input Dialog Box

P0005
Do you want to save and
continue?

Yes No

Figure 6.41
5) Press Yes or OK button to proceed. The scan tool will display
DTC definition as below.

60
 Trouble Codes

P0005
Fuel Shutoff Valve A Control
Circuit/Open

Save

Figure 6.42
 Use the LEFT/RIGHT scroll button to view the previous /
next DTC.

 Select Save to record code definition.

 For manufacturer specific codes, you need to select a vehicle

make on an additional screen to look for DTC definitions.

 If definition could not be found (SAE or Manufacturer

Specific), the scan tool displays “Please refer to vehicle
service manual!”

6) Press No or ESC button to return to previous menu.

61
7 Print Data
The Print Data function allows printing out diagnostic data
recorded by the scan tool or customized test reports by
connecting the scan tool to a PC or laptop with the USB cable
supplied.
 To print out retrieved data, you need the following tools:
MaxiDiag Elite Series scan tool
A PC or laptop with USB ports
A USB cable
1) Install Check-Elite PC Suit through the included CD, or
download the applications in our website: www.auteltech.com or
our distributors’ site.
2) Connect the scan tool to computer with the USB cable supplied.
3) Run Check-Elite Printer software on computer.
4) Select Playback function in Main Screen of the scan tool. In
Scan screen, use the UP/DOWN scroll button to select the files
you want to print. Wait for the reviewing window to display
(Figure 4.2), then select Print function on the bottom. The
selected file will be uploaded to your computer. For more
detailed instructions, please refer to 4. Playback Data.
5) The Check-Elite Printer will show as below.

Figure 7.1

62
6) The selected data will display on the textbox of Check-Elite
Printer. By selecting the function buttons on the right, you
could execute the following operations:

 Print – Print all data in the textbox to a printer connected to

your computer.
 Edit – Once clicked, the software will automatically open an
NOTEPAD window with all recorded data showing on.
 Copy – Copy all data in the textbox to the clipboard.
 Clear – Delete all data in the textbox.
 Exit – Quit the operation.

7) You are also allowed to edit, copy, and delete the data in the
Check-Elite Printer window.

NOTE: The scan tool can only print text data even though the
data is saved in graphic mode.

63
8 Software Update
This function allows you to update the scan tool software
through a computer.

8.1 Register the Tool

User would update the scan tool ONLY after you had registered the
tool on our website: www.maxidas.com. Then you could download
software, update online, retrieve information and get warranty
service.

NOTE: Prior to registration, please confirm your network is

working properly.

1. Log on the website www.maxidas.com.

2. Click on the Update tool bar at the top of the screen, and then
select User Register. Or, click on the Updates column in the
lower right corner of the screen, and select Register.
3. The screen of Register Information appears. Please read through
the instructions, and click on Agree to continue.
4. Put in the Product Serial No. and Register Password, and click
on Next. (Figure 8.1)
5. Follow the instructions on screen to finish the registration.

NOTE: Please use the About function to find out the Product
Serial No. and Register Password. For details, please refer to
the Section 3.6 System Setup.

64
 Figure 8.1

8.2 Update Procedure

Autel frequently releases software updates that you can download.
The Update feature makes it very easy to determine and get exactly
what you need.
1. Install Check-Elite PC Suit through the included CD, or
download the applications in our website: www.auteltech.com
or our distributors’ site.
2. Make sure that your computer is connected to the Internet.
3. Load the SD card of the scan tool to your PC.
4. Run the update option in Check-Elite PC Suit software. Wait
for the Log In window to pop up. (Figure 8.2)

Figure 8.2
65
5. Put in the user name and password and wait for the Check-Elite
Update window to display. If you forget your password
unintentionally, you may always click the [Forget your
password?] to link to our website and find your password back.
6. In the Update window, select the items you want to install.
Usually, you should install all available updates.

Figure 8.3

Generally, there are two ways to update programs:

Batch updating
 Select the programs that you would update by clicking on the
check boxes next to those items. Then click the Update
Selected Items button on the right side of screen.
 Or, click on the SELECT ALL checkbox on the right side of
screen and all updatable items will be selected automatically.
Then click the Update Selected Items button on the right side
of screen.
 Check the updating process by observing the upper left progress
bar [downloading] and upper right progress bar [installing]. You
may also find progress information in the Status column of
updated items.
 Anytime you could click the Pause button on the right side of
screen to suspend all progresses, and the state of those
suspended items would change to STOPPED.
 To resume updating process, you may need to select those
66
 suspended items again, then click the Update Selected Items
button. The progress will resume from the break point.
 When the downloading is completed, the downloaded programs
will be installed automatically. The new version will replace the
old version.
Single updating
 Find the desired updating item and click the INSTALL button in
the same line. With updating in progress, the INSTALL button
changes to STOP.
 Check the updating process by observing the upper left progress
bar [downloading] and upper right progress bar [installing]. You
may also find progress information in the Status column of
updated items.
 Anytime you could click the Pause button in the line to suspend
this progress, and the state of this item would change to
STOPPED.
 To resume updating process, click the INSTALL button in the
line again. The progress will resume from the break point.
 When the downloading is completed, the downloaded program
will be installed automatically. The new version will replace the
old version.

8.3 View or Delete Programs

To view the list of installed programs or to delete an installed
program, please follow these steps:
 Click on the Installed Programs tag entry and the page will
show the list of programs installed.
 Select the program(s) that you would delete.
 Batch delete: Select the programs that you would delete by
clicking on the check boxes to the left of those items. Then
click the DELETE button on the right side of screen.
 Single delete: Click the UNINSTALL button in the line of
your would-be-deleted program.
67
 A window asking “Are you sure to delete the software?” will
pop up for your confirmation.

Figure 8.4

 Click on Yes to delete the program(s) selected, or on No to

cancel the action.
 The deleted program will automatically add to the end of
program list in the UPDATE page in case you would like to
install again.

Theoretically, all programs in latest versions will be automatically

compatible with the older versions, but if your scan tool do have a
compatible problem and want to retrieve the older version for some
programs, you may need to delete them first then install the older
version again. Choose older version from the pull-down menu of
program version.

Figure 8.5
68
9 Warranty and Service
9.1 Limited One Year Warranty
Autel warrants to its customers that this product will be free from all
defects in materials and workmanship for a period of one (1) year from
the date of the original purchase, subject to the following terms and
conditions:
1) The sole responsibility of Autel under the Warranty is limited to
either the repair or, at the option of Autel, replacement of the scan
tool at no charge with Proof of Purchase. The sales receipt may be
used for this purpose.
2) This warranty does not apply to damages caused by improper use,
accident, flood, lightning, or if the product was altered or repaired
by anyone other than the Manufacturer’s Service Center.
3) Autel shall not be liable for any incidental or consequential
damages arising from the use, misuse, or mounting of the scan tool.
Some states do not allow limitations on how long an implied
warranty lasts, so the above limitations may not apply to you.
4) All information in this manual is based on the latest information
available at the time of publication and no warranty can be made
for its accuracy or completeness. Autel reserves the right to make
changes at any time without notice.

9.2 Service Procedures

If you have any questions, please contact your local store, distributor
or visit our website at www.auteltech.com.
If it becomes necessary to return the scan tool for repair, contact your
local distributor for more information.

69