Vicflex Style Vs1 Dry Sprinkler Models V3505, V3506, V3509, V3510, V3517, V3518

VicFlex™ Style VS1 Dry Sprinkler
Models V3505, V3506, V3509, V3510, V3517, V3518 10.91
1.0 PRODUCT DESCRIPTION

Style
• Pendent, Concealed Pendent, Horizontal Sidewall
K Factor
• 5.6/8.1 S.I.
For system design purposes, no equivalent length calculations are required.
Sprinkler Length
• 38"/965 mm, 50"/1270 mm, 58"/1475 mm
Nominal Orifice Size
• ½"/13 mm
Maximum Working Pressure
• 175 psi/1200 kPa
Factory Hydrostatic Test
• 100% @ 500 psi/3450 kPa
Minimum Operating Pressure
• 7 psi/48 kPa
Connections
• To branch line (inlet) via 1"/25 mm NPT or 1" BSPT
Minimum Bend Radius:
• UL: 2"/51 mm
• FM: 7"/178 mm
Maximum Number of 90° Bends:
• UL: 4
• FM: 2 bends for 38", 3 bends for 50", 4 bends for 58"
Hazard Classifications
• Light and Ordinary Hazard
NOTE
• The VS1 is classified as a dry sprinkler and has no equivalent length.
ALWAYS REFER TO ANY NOTIFICATIONS AT THE END OF THIS DOCUMENT REGARDING PRODUCT INSTALLATION, MAINTENANCE OR SUPPORT.
System No. Location Spec Section Paragraph
Submitted By Date Approved Date
victaulic.com
10.91 9374 Rev L Updated 11/2020 © 2020 Victaulic Company. All rights reserved.
1
victaulic.com
2.0 CERTIFICATION/LISTINGS
Model
Approvals/Listings V3505 V3505 V3506 V3506 V3509 V3509 V3510 V3517 V3518
Orifice Size (inches) 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2"
Orifice Size (mm) 13 13 13 13 13 13 13 13 13
Nominal K Factor Imperial 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6 5.6
Nominal K Factor S.I. 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1
Response Standard Standard Quick Quick Standard Standard Quick Standard Quick1
Hor. SW, Conc. Pend.
Deflector Type Pendent Recessed Pendent Recessed Hor. SW Rec. Hor. SW Recessed Hor. Conc. Pend. w/Clean
Sidewall room gasket
Approved Temperature
F°/C°
Ratings
135/57 135/57 135/57 135/57 135/57 135/57 135/57 – 135/57
155/68 155/68 155/68 155/68 155/68 155/68 155/68 – 155/68
FM 175/79 175/79 175/79 175/79 175/79 175/79 175/79 – 175/79
200/93 200/93 200/93 200/93 200/93 200/93 200/93 – 200/93
286/141 – – – 286/141 – – – –
135/57 135/57 135/57 135/57 135/57 135/57 135/57 135/57 135/57
155/68 155/68 155/68 155/68 155/68 155/68 155/68 155/68 155/68
UL 175/79 175/79 175/79 175/79 175/79 175/79 175/79 175/79 175/79
200/93 200/93 200/93 200/93 200/93 200/93 200/93 200/93 200/93
286/141 286/141 286/141 286/141 286/141 – 286/141 – –
1 Model V3518 is a Standard Response FM sprinkler.
3.0 MATERIAL SPECIFICATIONS

Deflector: Brass
Bulb: Glass with glycerin solution
Bulb Nominal Diameter:
Quick Response: 3.0 mm
Standard Response: 5.0 mm
Split Spacers: Stainless steel
Load Screw: Brass
Pip Cap: Stainless steel
Spring Seal Assembly: PTFE tape coated beryllium nickel and stainless steel
Frame: Brass
Flexible Hose: Stainless steel
Collar/Weld Fitting: Stainless steel
Gasket Seal: Victaulic EPDM
Isolation Ring: Nylon
Hose Fittings: Carbon steel, zinc-plated
Inlet Fitting: Brass
Outer Tube: Stainless steel
Concealed Cup: Carbon steel, zinc-plated
Brackets: Carbon steel, zinc-plated
3.1 ACCESSORIES SPECIFICATIONS

Sprinkler Finishes:
Standard: VC-250
White painted RAL 9010
victaulic.com 2
victaulic.com
4.0 DIMENSIONS
Product Details and Optional Components
Style VS1 Dry Sprinkler
B C
D
Overall Outlet
Length Live End Maximum
Sprinkler (pendent) Length Length OD
Length L B C D
inches inches inches inches inches
mm mm mm mm mm
38 39.2 25.1 6.5 2.2
965 995 638 165 56
50 51.2 37.1 6.5 2.2
1270 1300 943 165 56
58 59.2 45.1 6.5 2.2
1475 1505 1145 165 56
NOTE
• Add ½" to Overall Length and Outlet End Length for increased length of sidewall deflector
Style VB1 Bracket

2.7"/
68.6 mm
1.0"/ 2.25"/
25.4 mm 57.2 mm
2.2"/
54.6 mm*
4 x Ø .2"/
5.1 mm 3.6"/
92.1 mm
*Note: Theoretical center point of
sprinkler in bracket.
victaulic.com 3
victaulic.com
4.0 DIMENSIONS (CONTINUED)

Style VB2 Bracket Style VB3 Bracket
Recessed Pendent, Suspended Ceilings Concealed Pendent, Suspended Ceilings
Item Description Item Description

1 24"/610 mm or 48"/1220 mm Square Bar 1 24"/610 mm or 48"/1220 mm Square Bar
2 Patented 1-Bee Center Bracket 2 Patented 1-Bee Center Bracket
3 End Bracket 3 End Bracket
2
2
1
1
3 3
Style VB4 Bracket

Sleeve and Skirt Pendent, Suspended Ceilings
Item Description
1 24"/610 mm or 48"/1220 mm Square Bar
2 Center Bracket
3 End Bracket
victaulic.com 4
victaulic.com
4.1 DIMENSIONS
Sprinkler Finishes: Dimensions and Mounting Conditions
NOTE
• Drawings are shown with 5/8" finished ceiling thickness. Adjustments to "B" and "C" dimensions will be required if finished ceiling thickness deviate from drawing.
Recessed Pendent:
1"/ R
25 mm
A
Collar
2 ¾"/ B
70 mm D
5/8"/
16 mm
Finished
ceiling face
1"/25 mm Min. Escutcheon
1 ¾"/44 mm Max. 215⁄16"/75 mm
Clearance Chart
inches
Dimension mm
2 7
"R" Minimum Bend Radius
50 175
7 5/8 12 5/8
"A" Minimum Required Installation Space
193 320
4 3/4
"B" Mounting Screw Hole Location
119
2 – 2 3/8
Ceiling Hole Diameter "D"
50 – 60
NOTE
• Dimensions are shown with 3/4" escutcheon at middle of height adjustment range.
victaulic.com 5
victaulic.com
4.2 DIMENSIONS
Recessed Pendent Alternative Bracket Location
R
2¾"/
70 mm
1"/ A
25 mm Collar
D
5/8"/
16 mm
B C
Finished
ceiling face
1"/25 mm Min. Escutcheon
1¾"/44 mm Max. 215⁄ 16"/75 mm
Clearance Chart
inches
Dimension mm
2 7
50 175
7 5/8 12 5/8
193 320
2
50
2 – 2 3/8
50 – 60
NOTE
• Dimensions are shown with 3/4" escutcheon at middle of height adjustment range.
victaulic.com 6
victaulic.com
4.3 DIMENSIONS
Sleeve and Skirt Pendent
2¾"/
70 mm
1"/ R
25 mm
A
B 5/8"/
D 16 mm
Skirt Finished
Sleeve ceiling face
2½"/64 mm Min.
4"/102 mm Max.
37⁄ 32"/82 mm
Clearance Chart
inches
Dimension mm
2 7
50 175
6 ½ 11 ½
163 290
3 1/8
79
1 ¾ – 2 1/8
44 – 54
4.4 DIMENSIONS
Concealed Pendent
R
1"/
25 mm
A
2 ¾"/
70 mm
B
D
5/8"/
Cup 16 mm
R
Ceiling cover plate with ¼" Finished

total adjustment. Shown at ceiling face
3 ¼”/83 mm
mid-range of adjustment.
Clearance Chart
inches
Dimension mm
2 7
50 175
9 ½ 14 ½
241 369
6 ¼
157
2 5/8 – 2 ¾
67 – 70
victaulic.com 7
victaulic.com
4.5 DIMENSIONS
Concealed Pendent Alternative Bracket Location
R
2 ¾"/
70 mm
1"/
25 mm
A
D
B 5/8"/
Cup 16 mm
Ceiling cover plate with ¼" Finished

total adjustment. Shown at ceiling face
3 ¼"/83 mm
mid-range of adjustment.
Clearance Chart
inches
Dimension mm
2 7
50 175
9 1/8 14 1/8
231 358
3 ½
89
2 5/8 – 2 ¾
67 – 70
4.6 DIMENSIONS
Sleeve and Skirt Sidewall
A
31⁄8"/79 mm Min.
B
37⁄8"/98 mm Max.
1"/25 mm
R Skirt
Sleeve
37⁄32"/82 mm
2.70"/
69 mm
1¾"/44 mm Min. Dia. Exterior wall
2½"/64 mm Max. Dia. siding
Hole in wall 5/8"/16 mm
(Siding thickness)
Clearance Chart
inches
Dimension mm
2 7
50 175
6 ½ 11 ½
163 290
3 1/8
79
1 ¾ – 2 1/8
44 – 54
victaulic.com 8
victaulic.com
4.7 DIMENSIONS
Recessed Sidewall
A 19⁄16"/40 mm Min.
25⁄16"/59 mm Max.
B
1"/25 mm
2.70"/
R 69 mm
Collar
215⁄16"/59 mm
Escutcheon
2"/51 mm Min. Dia. Exterior wall

23⁄8"/60 mm Max. Dia. siding
Hole in wall 5/8"/16 mm
(Siding thickness)
Clearance Chart
inches
Dimension mm
2 7
50 175
8 13
203 330
4 3/4
119
2 – 2 3/8
51 – 60
4.8 DIMENSIONS
Recessed Sidewall Alternative Bracket Location
19⁄16"/40 mm Min.
A
25⁄16"/59 mm Max.
1"/25 mm B
R
Collar
215⁄16”/59 mm
Escutcheon
2.70"/
69 mm
2"/51 mm Min. Dia. Exterior wall
23⁄8"/60 mm Max. Dia. siding
Hole in wall 5⁄8"/16 mm
(Siding thickness)
Clearance Chart
inches
Dimension mm
2 7
50 175
8 13
203 330
2
51
2 – 2 3/8
51 – 60
victaulic.com 9
victaulic.com
4.9 DIMENSIONS
VB2 Recessed Pendent
A
See Chart
Bracket
Assembly
Style VB2
2.3"/58 mm
/ "/16 mm
Typical
ceiling tile
Finished
1.7"/43 mm ceiling face
Typical ceiling grid See note
Ceiling escutcheon with
¾"/19 mm total adjustment.
Shown at maximum recess
24"/610 mm or 48"/1219 mm
on Center
Recessed Pendent
Clearance Chart
inches
Dimension mm
2 7
50 175
6 ½ 11 ½
163 290
NOTE
• Victaulic VicFlex Style VB2 Bracket assemblies shall be used only with Style VS1 recessed pendent sprinklers.
4.10 DIMENSIONS
VB3 Concealed Pendent
A Bracket Assembly
See Chart
Style VB3
3.0"/76 mm
5/8"/16 mm
Typical ceiling
tile
1.7"/43 mm Finished
Typical ceiling grid See note ceiling face
Ceiling escutcheon with ¼"/6.5 mm
total adjustment
24"/610 mm or 48"/1219 mm
on Center
Concealed Pendent
Clearance Chart
inches
Dimension mm
2 7
50 175
7 5/8 12 5/8
193 320
NOTE
• Victaulic VicFlex Style VB3 Bracket assemblies shall be used only with Style VS1 concealed pendent sprinklers.
victaulic.com 10
victaulic.com
4.11 DIMENSIONS
VB4 Sleeve and Skirt Pendent
Bracket Assembly
Min. 1¾"/44 mm Style VB4
Max. 2½"/64 mm
A Hole in ceiling R
See Chart 3"/76 mm
1.7"/43 mm
Typical
ceiling grid
See note Skirt 5/8"/15.9 mm

Sleeve Typical Finished
ceiling tile Ceiling Face
37⁄32"/
82 mm
24"/610 mm or
48"/1219 mm on Center
Sleeve and Skirt Pendent
Clearance Chart
Bend Radius
inches inches
mm mm
2 7
51 178
5 10
127 254
NOTE
• Victaulic VicFlex Style VB2 Bracket assemblies shall be used only with Style VS1 recessed pendent sprinklers.
victaulic.com 11
victaulic.com
5.0 PERFORMANCE
Freeze Protection
Y
Face of
Fitting
Unheated
Space
Unheated
Y Space
Face of Heated
Fitting
Space
Heated
Space Exterior
Exterior
Ambient Temperature Exposed Minimum Barrel Length "Y"

Exposed to Discharge inches
End of Sprinkler mm
°F
°C 40°F/4°C 50°F/10°C 60°F/16°C
40 0 0 0
4 0 0 0
30 0 0 0
-1 0 0 0
20 4 0 0
-7 100 0 0
10 8 1 0
-12 200 25 0
0 12 3 0
-18 300 75 0
-10 14 4 1
-23 350 100 25
-20 14 6 3
-29 350 150 75
-30 16 8 4
-34 400 200 100
-40 18 8 4
-40 450 200 100
-50 20 10 6
-46 500 250 150
-60 20 10 6
-51 500 250 150
NOTE
• Exposed minimum barrel lengths are inclusive up to 30-mph/48-kph wind velocities.
Maximum Allowable Number of Bends
Sprinkler Length Maximum Allowable Number of 90° Bends at Maximum Allowable Number of 90° Bends at
inches 2"/51mm Bend Radius for UL Listing 7"/178mm Bend Radius for FM Approval
mm
38
4 2
965
50
4 3
1270
58
4 4
1475
victaulic.com 12
victaulic.com
6.0 NOTIFICATIONS
WARNING
• Read and understand all instructions before attempting to install

any Victaulic products.
• Always verify that the piping system has been completely
depressurized and drained immediately prior to installation,
removal, adjustment, or maintenance of any Victaulic products.
• Wear safety glasses, hardhat, and foot protection.
• These products shall be used only in fire protection systems that are designed and installed in accordance
with current, applicable National Fire Protection Association (NFPA 13, 13D, 13R, etc.) standards, or equiva-
lent standards, and in accordance with applicable building and fire codes. These standards and codes contain
important information regarding protection of systems from freezing temperatures, corrosion, mechanical dam-
age, etc.
• The installer shall understand the use of this product and why it was specified for the particular application.
• The installer shall understand common industry safety standards and potential consequences of improper
product installation.
WARNING
• It is the responsibility of the system designer to verify suitability of 300-series stainless steel flexible hose for
use with the intended fluid media within the piping system and external environments.
• The effect of chemical composition, pH level, operating temperature, chloride level, oxygen level, and flow rate
on 300-series stainless steel flexible hose must be evaluated by the material specifier to confirm system life will
be acceptable for the intended service.
• It is the responsibility of the owner of a building or their authorized agent to provide the sprinkler system installer
with any knowledge that the water supply might be contaminated with or conducive to the development of
microbiologically influenced corrosion (MIC), including as required by NFPA 13. Failure to identify adverse water
quality issues may affect the VicFlex product and void the manufacturer’s warranty.
Failure to follow these instructions could cause product failure, resulting in serious personal injury and/or
property damage.
DO NOT paint, coat, or firestop the outlet/inlet portion of the Style VS1 Dry Sprinkler. Braided hose and fitting
portions of the Style VS1 Dry Sprinkler may be painted or coated, provided that the paint or coating is compatible
with stainless steel material. This includes penetration through firestop-filled annular space of a firewall. The firestop
material in direct contact with the flexible braided hose will not impede functionality of the Style VS1 Dry Sprinkler,
provided that the components are installed in accordance with Victaulic's installation instructions.
victaulic.com 13
victaulic.com
6.0 NOTIFICATIONS (CONTINUED)

Important Installation Notes:
1. Shall be installed only in accordance with NFPA 13 Standard for the the Installation of Sprinkler Systems and
applicable FM Data Sheets.
2. Install and tighten swivel hex nut at inlet of sprinkler fitting only.
3. Do not remove deflector or inlet end of sprinkler.
Inlet Continuous Downward Slope

Inlet Continuous Downward Slope
Heated Space Unheated Space Outlet
Heated Space Unheated Space
Outlet ACCEPTABLE
ACCEPTABLE
Inlet Inlet
Low Point Low Point
Heated Space Unheated Space

Heated Space Unheated Space Outlet
Outlet
UNACCEPTABLE UNACCEPTABLE
victaulic.com 14
victaulic.com
6.0 NOTIFICATIONS (CONTINUED)

FOR DRY SYSTEMS ONLY:
• The Style VS1 Dry Sprinkler’s inlet shall be installed only into the outlet of a fitting (excluding elbows) or welded
outlet that meets the dimensional requirements of ANSI B16.3 and ANSI B16.4, Class 125 and Class 150. Use a
sample fitting to confirm proper engagement and to verify that there is no interference between the sprinkler and
the fitting.
Style VS1 Dry Sprinklers in an unheated space shall be installed with a continuous downward slope along its
entire length from the branch line fitting to the sprinkler. No localized low points shall be present along the
length of the Style VS1 Dry Sprinkler.
Style VS1 Dry Sprinklers in an unheated space are not permitted to be installed into the top of the branch line
piping. Style VS1 Dry Sprinklers shall be installed into the side or from the bottom of the branch line piping.
In a heated space, if a portion of the Style VS1 Dry Sprinkler is installed from the top of a branch line and then
extends into an unheated space, it shall be installed with a continuous downward slope along the entire length
from the inside wall to the outlet of the sprinkler. No localized low points shall be present along the length of the
sprinkler in the unheated space. Refer to the drawing below.
Downward
Slope
Unheated Space
Heated Space
Inlet
Outlet
FOR WET SYSTEMS ONLY:

• DO NOT install Victaulic® VicFlex™ Style VS1 Dry Sprinklers into any threaded elbow, threaded-by-thread
coupling, or fitting that interferes with thread penetration. The inlet of the Victaulic® VicFlex™ Style VS1 Dry
Sprinkler SHALL NOT bottom out in the fitting. Use a sample fitting to confirm proper engagement.
• To ensure unobstructed flow during operation, the Victaulic® VicFlex™ Style VS1 Dry Sprinkler shall be installed
into a fitting that will prevent water and debris from accumulating at the dry sprinkler’s inlet.
• Verify that the exposed minimum barrel length in the heated space is measured and maintained in accordance
with the table on page 1.
In a heated space, if a portion of the Style VS1 Dry Sprinkler extends into an unheated space, it shall be
installed with a continuous downward slope along the entire length from the inside wall to the outlet end of the
dry sprinkler. No localized low points shall be present along the length of the sprinkler in the unheated space.
Refer to the drawing above.
victaulic.com 15
victaulic.com
7.0 REFERENCE MATERIALS

ONE BEND TWO BENDS
2X
Minimum 2X Minimum
Minimum
Minimum bend radius
bend radius bend radius
bend radius
90°
OR
OR
Minimum
bend radius Minimum
Minimum bend radius
bend radius
Minimum
bend radius
Minimum
bend radius
NOTE
For out-of-plane (three-dimensional) bends, care must be taken to avoid imparting torsional stress on the sprinkler.
victaulic.com 16
Bill Company Name Order No. Date
To:
Ship
Address To: Company Name
Address
victaulic.com
victaulic.com
State/Province Zip Code/Postal Code
Phone No. Email State/Province Zip Code/Postal Code
Fax No. Tag
10.91 9374 Rev L Updated 11/2020

7.0 REFERENCE MATERIALS
Quantity (as specified below): If units of different size, type or other option are required, please attach additional form(s) with their specification(s) separately.
VicFlex™ Dry Sprinkler Model VS1
A – 3F – – – – – 4 – – – –
17
© 2020 Victaulic Company. All rights reserved.
Recessed Size
Deflector Escutcheon Escutcheon
Class Style Thread Style Temperature Response K Factor Finish Material Code Inches Style †
A 3F = 3 = 1" NPT B = Pendent A = 135°F/57°C Q = Quick 4 = K5.6 4 = White W = White 380 = 38" 12 = Recessed
V35 8 = 25 mm C = Horizontal C = 155°F/68°C S = Std. N = VC-250 ‡ Stainless Steel 500 = 50" 13 = Sleeve and
BSP Sidewall E = 175°F/79°C X = Stainless Steel 580 = 58" Skirt
P - Concealed F = 200°F/93°C 0 = Concealed 15 = Concealed
J = 286°F/141°C
‡ VC-250 sprinkler finish sold standard on the VicFlex Dry Sprinkler Model VS1.
victaulic.com
7.0 REFERENCE MATERIALS (CONTINUED)

29.01: Victaulic Terms and Conditions of Sale
I-VICFLEX.VS1: Victaulic® VicFlex™ Style VS1 Dry Sprinkler Installation Instructions
User Responsibility for Product Selection and Suitability Note

Each user bears final responsibility for making a determination as to the suitability of This product shall be manufactured by Victaulic or to Victaulic specifications. All products
Victaulic products for a particular end-use application, in accordance with industry to be installed in accordance with current Victaulic installation/assembly instructions.
standards and project specifications, and the applicable building codes and related Victaulic reserves the right to change product specifications, designs and standard
regulations as well as Victaulic performance, maintenance, safety, and warning equipment without notice and without incurring obligations.
instructions. Nothing in this or any other document, nor any verbal recommendation, Installation
advice, or opinion from any Victaulic employee, shall be deemed to alter, vary, supersede, Reference should always be made to the Victaulic installation handbook or installation
or waive any provision of Victaulic Company's standard conditions of sale, installation instructions of the product you are installing. Handbooks are included with each shipment
guide, or this disclaimer. of Victaulic products, providing complete installation and assembly data, and are available
Intellectual Property Rights in PDF format on our website at www.victaulic.com.
No statement contained herein concerning a possible or suggested use of any material, Warranty
product, service, or design is intended, or should be constructed, to grant any license Refer to the Warranty section of the current Price List or contact Victaulic for details.
under any patent or other intellectual property right of Victaulic or any of its subsidaries
or affiliates covering such use or design, or as a recommendation for the use of such Trademarks
material, product, service, or design in the infringement of any patent or other intellectual Victaulic and all other Victaulic marks are the trademarks or registered trademarks of
property right. The terms “Patented” or “Patent Pending” refer to design or utility patents Victaulic Company, and/or its affiliated entities, in the U.S. and/or other countries.
or patent applications for articles and/or methods of use in the United States and/or other
countries.
victaulic.com 18

Vicflex Style Vs1 Dry Sprinkler Models V3505, V3506, V3509, V3510, V3517, V3518

Uploaded by

Copyright:

Available Formats

Vicflex Style Vs1 Dry Sprinkler Models V3505, V3506, V3509, V3510, V3517, V3518

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Vicflex Style Vs1 Dry Sprinkler Models V3505, V3506, V3509, V3510, V3517, V3518

Uploaded by

Copyright:

Available Formats

VicFlex™ Style VS1 Dry Sprinkler

Models V3505, V3506, V3509, V3510, V3517, V3518 10.91

1.0 PRODUCT DESCRIPTION

System No. Location Spec Section Paragraph

Submitted By Date Approved Date

3.0 MATERIAL SPECIFICATIONS

3.1 ACCESSORIES SPECIFICATIONS

Style VB1 Bracket

4.0 DIMENSIONS (CONTINUED)

Item Description Item Description

Style VB4 Bracket

Ceiling cover plate with ¼" Finished

Ceiling cover plate with ¼" Finished

2"/51 mm Min. Dia. Exterior wall

See note Skirt 5/8"/15.9 mm

Ambient Temperature Exposed Minimum Barrel Length "Y"

Maximum Allowable Number of Bends

• Read and understand all instructions before attempting to install

6.0 NOTIFICATIONS (CONTINUED)

Inlet Continuous Downward Slope

Heated Space Unheated Space Outlet

Heated Space Unheated Space

Low Point Low Point

Heated Space Unheated Space

6.0 NOTIFICATIONS (CONTINUED)

FOR WET SYSTEMS ONLY:

7.0 REFERENCE MATERIALS

State/Province Zip Code/Postal Code

Phone No. Email State/Province Zip Code/Postal Code

Fax No. Tag

10.91 9374 Rev L Updated 11/2020

VicFlex™ Dry Sprinkler Model VS1

7.0 REFERENCE MATERIALS (CONTINUED)

User Responsibility for Product Selection and Suitability Note

You might also like