英文 485通讯

Hartzell Engine Technologies LLC
2900 Selma Highway

Montgomery, AL 36108, USA
Tel: +1.334.386.5400 Fax: +1.334.386.5410
AIRCRAFT ALTERNATOR
OWNER'S MANUAL
P/N ES1032
ALTERNATOR
MODELS
ES-6904
ES1032 24-30-01
Title Page Page: i
Rev. New Issued: August 4, 2016
Aircraft Alternator
Owners Manual
Copyright © 2016 Hartzell Engine Technologies LLC
All rights reserved. No part of this publication may be reproduced,

stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise, without
the prior written permission of Hartzell Engine Technologies LLC.
24-30-01 ES1032
Page: ii
Issued: August 4, 2016 Rev. New
Aircraft Alternator
Owners Manual
TABLE OF CONTENTS
DESCRIPTION PAGE
Title Page i
Copyright Statement ii
Table of Contents iii
Warning Letter v
Record of Revisions vii
Record of Temporary Revisions ix
Service Publication List xi
List of Effective Pages xiii
List of Illustrations xv
List of Tables xvi
AIRWORTHINESS LIMITATIONS
A.0 General A-1
A.1 Airworthiness Limitation Statement A-1
A.2 Life Limits A-2
INTRODUCTION
1.0 General 1-1
1.1 General Specifications (manual) 1-2
1.2 How to Use the Manual 1-2
1.3 Measurements 1-3
1.4 Units of Measure 1-3
1.5 Abbreviations 1-4
1.6 Definitions 1-4
1.7 Disposal 1-6
1.8 Model Identification 1-7
1.9 Serial Number Identification 1-7
1.10 Warranties 1-7
DESCRIPTION AND OPERATION
2.0 General 2-1
2.1 Basic Component Description 2-1
2.2 Technical Purpose 2-2
2.3 Physical Detail 2-3
2.4 Theory of Operation 2-3
2.5 Self Excitation 2-4
2.6 Operational Data 2-4
2.7 Appearance 2-5
TROUBLESHOOTING
3.0 General 3-1
3.1 Procedure 3-1
3.2 Troubleshooting Charts 3-2
CHECK
4.0 General 4-1
4.1 Inspection Checks 4-1
ES1032 24-30-01
TOC Page: iii
Aircraft Alternator
Owners Manual
TABLE OF CONTENTS (Cont’d)

TESTING
5.0 General 5-1
5.1 Testing 5-1
A. Equipment 5-1
B. Test Conditions 5-1
C. Precautions 5-2
5.2 Testing & Inspection 5-3
A. Arc Marks on Terminals 5-3
B. Bearing Inspection 5-3
C. Field Circuit Open or Ground Test Procedure 5-3
D. Mounting Hardware 5-4
E. Insulators (Washers and Spacers) 5-4
F. Brush holder, Brushes and Springs 5-4
G. Drive Spline 5-4
5.3 Alternator Bench Testing 5-5
A. Alternator Output Test Conditions 5-5
B. Test Set Up 5-5
C. Ventilation 5-6
D. Test Procedures 5-6
E Alternator Output Test Specifications 5-7
MAINTENANCE
6.0 General 6-1
6.1 Periodic Maintenance 6-1
6.2 Torque Information 6-1
6.3 Alternator Spline Drive Inspection & Maintenance 6-2
6.4 Removal from Aircraft 6-3
6.5 Exterior Cleaning 6-3
6.6 Brush Removal and Installation 6-4
6.7 Through Bolts (Thru Bolts) 6-5
6.8 Terminal Hardware Removal and Installation 6-6
6.9 Materials 6-7
6.10 Applying Safety Wire 6-8
6.11 Applying Safety Cable 6-8
6.12 Installation on the Aircraft 6-8
6.13 Special Conditions 6-9
A. Sudden Stoppage 6-9
B. Lightning Strike 6-9
6.14 Storage and Shelf Life 6-10
24-30-01 ES1032
Page: iv TOC
Aircraft Alternator
Owners Manual
Thank you for purchasing a Hartzell Engine Technologies alternator. We encourage you to
read this manual thoroughly. It contains a wealth of information about how to properly install
and maintain your alternator so that it may give you many years of safe and reliable service.
Should you have a question regarding your alternator that is not covered in the manual,
Hartzell Engine Technologies Product Support is ready to assist you. We may be reached at
the following contact information:
Phone: +1.334.386.5400, option 2

E-mail: [email protected]
Fax: +1.334.386.5450
Web: www.Hartzell.aero/contact/
W A R N I N G:
People who fly should recognize there are various types of risks involved in this
activity; and they should take all precautions to minimize them, since they cannot
be eliminated entirely. The alternator is an important component of the aircraft.
An alternator failure could result in an unplanned landing or even more severe
consequences creating an unsafe condition that may result in death, serious bodily
injury, and/or substantial property damage. It is, therefore, essential for the alternator
to be properly maintained according to the recommended service procedures and
monitored to detect impending problems before they become serious. Any unusual
operation should be investigated and corrected, as it may be a warning of impending
failure.
ES1032 24-30-01
Page: v
Aircraft Alternator
Owners Manual
INTENTIONALLY LEFT BLANK
24-30-01 ES1032
Page: vi
Aircraft Alternator
Owners Manual
Record of Revisions
Revision Issue Page Inserted

Letter Date Revised Description Date By
New 8-04-16 N/A Original
ES1032 24-30-01
ROR Page: vii
Aircraft Alternator
Owners Manual
Record of Revisions
Revision Issue Page Inserted

Letter Date Revised Description Date By
24-30-01 ES1032
Page: viii ROR
Aircraft Alternator
Owners Manual
Record of Temporary Revisions

Temporary Page Issue Date
By By
Rev. Letter Number Date Removed
ES1032 24-30-01
ROTR Page: ix
Aircraft Alternator
Owners Manual
Record of Temporary Revisions

Temporary Page Issue Date
Number Date By Removed By
Rev. Letter
24-30-01 ES1032
Page: x ROTR
Aircraft Alternator
Owners Manual
Service Publication List
Pub. Number Description Alternator Affected
ES1032 24-30-01
SPL Page: xi
Aircraft Alternator
Owners Manual
Service Publication List
Pub. Number Description Alternator Affected
24-30-01 ES1032
Page: xii SPL
Aircraft Alternator
Owners Manual
List of Effective Pages
Content of Pages Page Date of Latest Revision
Title Page - i Rev. New - 8-04-16

Copyright statement ii Rev. New - 8-04-16
Table of Contents - iii, iv Rev. New - 8-04-16
Warning Letter v, vi Rev. New - 8-04-16
Record of Revisions vii, viii Rev. New - 8-04-16
Temporary Record of Revisions ix, x Rev. New - 8-04-16
Service Publication List xi, xii Rev. New - 8-04-16
List of Effective Pages xiii, xiv Rev. New - 8-04-16
List of Illustrations xv Rev. New - 8-04-16
List of Tables xvi Rev. New - 8-04-16
Airworthiness Limitations A-1, A-2 Rev. New - 8-04-16
Introduction 1-1 thru 1-8 Rev. New - 8-04-16
Description of Operation 2-1 thru 2-6 Rev. New - 8-04-16
Troubleshooting 3-1 thru 3-10 Rev. New - 8-04-16
Check 4-1 & 4-2 Rev. New - 8-04-16
Testing 5-1 thru 5-8 Rev. New - 8-04-16
Maintenance 6-1 thru 6-10 Rev. New - 8-04-16
ES1032 24-30-01
LOEP Page: xiii
Aircraft Alternator
Owners Manual
List of Effective Pages
Content of Pages Page Date of Latest Revision
24-30-01 ES1032
Page: xiv LOEP
Aircraft Alternator
Owners Manual
LIST OF ILLUSTRATIONS
PAGE
Figure 2.1 Alternator Simplified Electrical Diagram 2-1
Figure 2.2 - Stator Wiring Diagram (Typical) 2-2

Figure 2.3 - Typical Cutaway (basic components) 2-3
Figure 2.4a - ES-6904 Front View 2-5
Figure 2.4b - ES-6904 Rear View 2-5
Figure 5.1 - Typical Bench Testing Set Up 5-5
Figure 6.1a - Spline Drive with Shear Section 6-2
Figure 6.1b - V-Clamp Attachment 6-3
Figure 6.2a - Brush Holder Locations 6-4
Figure 6.2b - Brush Holder Installation 6-4
Figure 6.2c - Brush Position in Holder 6-4
Figure 6.2d - Brush Retaining Wire 6-4
Figure 6.3a - Terminal Hardware Stack 6-6
Figure 6.3b - Field Terminal Hardware Stack 6-6
ES1032 24-30-01
LOI Page: xv
Aircraft Alternator
Owners Manual
LIST OF TABLES
PAGE
Table 2.1 - Operational Specifications 2-4
Table 3.1 - Low or No Alternator Output 3-2
Table 3.2 - Battery Discharged 3-3
Table 3.3 - Battery Overcharged 3-4
Table 3.4 - Noisy Alternator (acoustic) 3-5
Table 3.5 - Noisy Alternator (electrical) 3-6
Table 3.6 - Ammeter Erratic or Lights Flicker 3-7
Table 5.1 - Output Test Specifications ES-6904 5-7
Table 6.1 - Torque Specifications 6-1
24-30-01 ES1032
Page: xvi
Aircraft Alternator
Owners Manual
AIRWORTHINESS LIMITATIONS
A.0 General Information
CAUTION:
THE AIRWORTHINESS LIMITATIONS IN THIS MANUAL ARE THOSE
MANDATED BY HARTZELL ENGINE TECHNOLOGIES. THESE
LIMITATIONS ARE THE MINIMUM REQUIRED TO MEET CONTINUED
AIRWORTHINESS BUT MAY BE SUPERSEDED BY MORE STRINGENT
REQUIREMENTS AS PUBLISHED BY THE FAA, AIRCRAFT,
ROTORCRAFT OR OTHER MANUFACTURERS THAT USE THESE
COMPONENTS IN THEIR APPLICATIONS. FAILURE TO OBSERVE
THESE LIMITATIONS MAY COMPROMISE THE COMPONENT OR THE
APPLICATION IT IS USED IN.
A.1 Airworthiness Limitation Statement
Airworthiness
Limitations
A. The Airworthiness Limitations section is FAA approved and specifies maintenance required
under Secs. 43.16 and 91.403 of the Federal Aviation Regulations unless an alternative program
has been FAA approved.
Airworthiness Limitation Revisions Log

Revision Number Description of Revision
ES1032 24-30-01
ICA Page: A-1
Aircraft Alternator
Owners Manual
AIRWORTHINESS LIMITATIONS (cont’d)
A.2 Life Limits
A. The FAA establishes specific life limits for certain component parts as well as the complete
alternator. Such limits require replacement of the identified parts after a specified
number of cycles or hours of use.
B. Additions of, or changes to, any life limit for the alternator or its components, will be
noted in the Airworthiness Limitation Revision Log.
C. Life Limits
(1) Alternator models and their component parts affected by this manual currently
do not have any life limited parts.
(2) There are no new (or additional) Airworthiness Limitations associated with this
equipment.
24-30-01 ES1032
Page: A-2
Aircraft Alternator
Owners Manual
INTRODUCTION
1.0 General Information
WARNING:
IMPROPER OR UNAUTHORIZED APPLICATIONS OF THE INFORMATION
CONTAINED IN THE MANUAL MAY RENDER THE AIRCRAFT OR THE
COMPONENT UNAIRWORTHY AND RESULT IN LOSSES, DAMAGES, OR
INJURY TO THE USER.
DO NOT USE OBSOLETE OR OUTDATED INFORMATION. PERFORM ALL
INSPECTIONS OR WORK IN ACCORDANCE WITH THE MOST RECENT
REVISION OF THIS MANUAL. INFORMATION CONTAINED IN THIS
M A N UA L MAY BE SIGNIFICANTLY CHANGED FROM E A R L I E R
REVISIONS. USE OF OBSOLETE INFORMATION MAY CREATE AN
UNSAFE CONDITION THAT MAY RESULT IN DEATH, SERIOUS BODILY
INJURY, AND/OR SUBSTANTIAL PROPERTY DAMAGE. REFER TO THE
MANUAL INDEX FOR THE MOST RECENT REVISION LEVEL.
The accuracy and applicability of this manual has not been verified for any assembly, component or part
not manufactured by Hartzell Engine Technologies LLC (HET). Any use of the manual for other than its
intended or implied purpose is prohibited. The use of the manual for the purpose of performing any
installation, maintenance, replacement, adjustment, or inspection of any assembly, component or part not
manufactured by HET is not approved, endorsed, or sanctioned by HET.
This manual has been reviewed and accepted by the FAA. Additionally, the Airworthiness Limitations
Section of this manual has been approved by the FAA.
This manual has been approved by Hartzell Engine Technologies LLC as the proper methods and
procedures that FAA or other airworthiness authority Certificated Repair Stations and A/P Mechanics
should use in the inspection and maintenance of the subject Hartzell Engine Technologies LLC alternator.
No liability will be assumed by Hartzell Engine Technologies LLC for actual, consequential, incidental or
other types of damages directly or indirectly resulting from the unauthorized use of this manual for other
than its stated purposes.
The liability for use of the authorized data in this manual for the maintenance, or return to service is
limited to the specific terms and conditions stated under the applicable Limited Warranty in effect for each
piece part, component, assembly or whole unit sold by HET.
Because of the numerous modifications, Supplemental Type Certificates (STC), Parts Manufacturing
Approvals (PMA), or Form 337 Field Approvals that may apply, it is the responsibility of the repairman,
mechanic or maintenance facility to determine the proper engine or aircraft application of this alternator
assembly. Please refer to the appropriate aircraft Type Certificate (TC), Supplemental Type Certificate
(STC), aircraft equipment list, maintenance manuals, and/or Log Book entries for determination.
When performing installation, maintenance, replacement, adjustment, or inspection of any HET assembly,
component or part, it is imperative that the latest revision of this HET manual or other product support
document be referenced. Reference the HET website to be sure you have the latest revision before
performing any work. (http://www.hartzell.aero/maintenance-manuals/)
All reasonable attempts were made to make this manual as complete and accurate as possible. If you
have any questions, comments, corrections or require clarification of any information contained in this
manual, please write to Hartzell Engine Technologies LLC, 2900 Selma Highway, Montgomery, Alabama,
36108 USA. TEL +1.334.386.5400, FAX +1.334.386.5410, or http://hartzell.aero/contact/.
ES1032 24-30-01
Page: 1-1
Aircraft Alternator
Owners Manual
1.1 General Specification (manual)
A. This manual follows unique HET formatting using ATA 100 identification as required.
Principle units of measure in the manual are U.S. units with International System of Units (SI)
in parentheses.
B. The ES-6904 series (24v) alternator models are considered in this manual. Variations of
these alternators may be noted as applicable.
C. All aircraft, rotorcraft, or engine applications are limited to the holder of the TC, STC, PMA
or TSO and only at the date of that document publication or revision.
D. Only approved, competent persons with the necessary skills may do maintenance tasks
described in the manual.
E. The manual describes maintenance on components as they are installed on aircraft and
tasks that should be accomplished in a properly equipped service facility.
F. Maintenance tasks and subtasks are referenced in the manual but will have no specific
identification numbers.
G. The manual contains: Description and operation, Troubleshooting, Instruction for Continued
Airworthiness (ICA) and Maintenance information along with part numbers required for basic
maintenance tasks.
1.2 How to use the manual:
A. Make sure the manual contains information applicable to your aircraft, engine, or
replacement alternator. Look for the model number on the Title Page and if applicable,
the part number of the replacement or superseded component.
B. It is imperative that you read, understand, and observe all the applicable WARNINGS and
CAUTIONS before you do any work on this component.
C. Use only the sections needed. Use the check section to determine what actions may be
needed periodically and the maintenance sections for servicing the alternator.
D. If you need to identify a part or find a part number, refer to illustrations or reference in
this manual or in the applicable aircraft or engine service or maintenance manual.
E. Refer to the troubleshooting section to assure that the observed or reported condition lies
with the alternator.
F. Fully test the alternator per the instructions in this manual when running the aircraft.
Utilize the aircraft and/or engine manufacturer’s service manuals and publications before
returning the aircraft to service. Use the AFM or POH for aircraft operations.
24-30-01 ES1032
Page: 1-2
Aircraft Alternator
Owners Manual
1.3 Measurements
The measurements given in the manual are taken from original manufacturing drawings.
Measurements are given in U.S. Units followed by SI Units in parentheses.
1.4 Units of Measure
A. SI Units
A Ampere
Ah Ampere hours
g Gram
min Minute
N Newton
Nm Newton meter
VDC Volt direct current
o
C Degree Celsius
% Percent
Ω Ohm
W watt
Hz Hertz
B. U.S. Units (SI units)
ft (m) Foot (meter)

in (c) Inch (centimeter)
lb (kg) Pound (kilogram)
lb-in (Nm) Pound inch (Newton meter) torque
lb-ft (Nm) Pound foot (Newton meter) torque
o
F (oC) Degree Fahrenheit (centigrade)
C. Multiplying Prefixes
µ Micro
m Milli
k Kilo
M Mega
p pico
ES1032 24-30-01
Page: 1-3
Aircraft Alternator
Owners Manual
1.5 Abbreviations
A. The abbreviations given below are used in the manual: (upper or lower case)
ACU Alternator Control Unit
AFM Aircraft Flight Manual
ALT Alternator
ATA Air Transport Association of America
DE Drive End (housing)
DIA Diameter
FAA Federal Aviation Administration (USA)
FIG. Figure
GAMA General Aviation Manufacturers Association
IPC Illustrated Parts Catalog
ID Inside Diameter
HET Hartzell Engine Technologies LLC
MAX Maximum
MFR Manufacturer
MIN Minimum
NO. Number
N/A Not Applicable
OD Outside Diameter
PCB Printed Circuit Board
POH Pilots Operating Handbook
P/N Part Number
PARA. Paragraph
REF. Refer To
S/A Subassembly
S/N Serial Number
STC Supplemental Type Certificate
SRE Slip Ring End (housing) Same as CE
TBD To Be Defined
TC Type Certificate
TIS Time In Service
TOL Tolerance
1.6 Definitions
A. This paragraph defines the warnings and notifications used in this manual. WARNINGS
place critical attention to use of tools, materials, procedures, or limitations, which must be
followed without deviation to avoid injury to the technician or other persons. CAUTIONS
place immediate attention to use of tools and procedures which must be followed to avoid
injury, damage to equipment and/or facilities. Notes call attention to procedures which
make the job easier.
B. The following are basic definitions of the terms used in this manual:
ALTERNATOR: The complete unit which transforms rotational energy from a powerplant
into electrical energy. At a given voltage, produces alternating current (AC) which is
converted to direct current (DC).
ALTERNATOR CONTROL UNIT: Device which controls alternator functions on, off,
regulation of high/low voltage, field current and output current.
24-30-01 ES1032
Page: 1-4
Aircraft Alternator
Owners Manual
BRUSH: Device for conducting current to the slip rings of the rotor. It is a composite
carbon block which includes a spring, lead and contact.
BRUSH HOLDER ASSEMBLY: Device that retains multiple brush assemblies and is
comprised of a holder, brushes, springs, contacts, and terminals.
CARBON PILE: Regulator device used in testing. The carbon pile is basically a large
resistor that may be adjusted. It is formed of carbon granules, and its resistance is
dependent on the pressure applied across the granules. Mechanical adjustment controls
the pressure across the granules in such a way as to increase or decrease resistance
(basic regulator).
CONTINUITY: The continuous path for the flow of current in an electrical circuit.
COOLING COVER: Device attached to the alternator to provide cooling air from an
external source. May be provided with alternator or installed by the airframe manufacturer.
(Also known as the “Blast Tube”, referring to ram air cooling source.)
EMI: Electro Magnetic Interference. A disturbance in the radio-frequency spectrum that is

generated by an external source that affects electrical devices or circuits by electromagnetic
induction, electrostatic coupling, or conduction.
FRONT HOUSING: Part of the external housing which contains the components of the
alternator. This end has structure typically used for mounting. It may also be referred to as
the Drive End Housing or D.E.
INSULATOR: Component that does not allow electricity to flow through it easily. Insulators
do not allow electricity to flow through them easily because the electrons in their atoms
do not move easily from atom to atom.
MULTIMETER: Device for the measurement of voltage, current, or resistance.
LEAKAGE: Dissipation of voltage or current from a component or connection.
OPEN: Electrical term for a complete disruption of a conductive path in an electrical circuit.
Will read infinite resistance.
PEAK INVERSE VOLTAGE: (PIV) The maximum rated value of a AC voltage acting in
the direction opposite to that in which a device is designed to pass current.
PHASE: The position of a point in time (instant) on a waveform cycle. A complete cycle is
defined as 360 degrees of phase. Phase can also be an expression of relative displacement
between or among waves having the same frequency.
POLARIZE: To induce polarization i.e., the partial or complete polar separation of positive
and negative electric charge in an electrical system.
REAR HOUSING: Part of the external housing which contains the components of the
alternator. It may also be referred to as the Slip Ring End or S.R.E.
RECTIFIER: An electrical circuit used to convert AC into DC current. The rectifier is a

network of diodes that causes the current to flow in only one direction.
ES1032 24-30-01
Page: 1-5
Aircraft Alternator
Owners Manual
RFI: Radio Frequency Interference. Electromagnetic energy in the radio-frequency

spectrum. Electrical interference may be created by poor slip ring/brush connection,
defective rectifiers, or other poor connections. This is a normal by-product of electrical
generators.
ROTOR: Rotating electro magnet used to create a magnetic field.
SLIP RING: Device which provides a sliding contact surface for the brush assemblies. The
slip rings are smooth surface copper “rings” pressed onto the rotor shaft.
SHORT: Common term for a connection which has very little or no resistance as seen on
an Ohmmeter in an electrical circuit. Typically an undesirable condition with respect to
grounded elements.
SPLINE: A series of uniformly spaced ridges (teeth) on a shaft, parallel to its axis that fit
inside corresponding grooves in the hub of a gear used to transmit torque.
STATOR: A stationary set of conductors wound in coil form on an iron core.
TEST BENCH: Device so constructed as to allow testing of the alternator or component

parts.
TERMINALS: Studs, screws or other devices that provide connections for electrical power.
THROUGH BOLT: Special bolts which connect front and rear alternator housings.
VOLT/OHM METER: Device for the measurement of voltage or resistance.
1.7 Disposal
A. HET alternator assemblies are designed to allow for overhaul and re-use of many of the
subassemblies and components.
1. Disposal of unairworthy parts and assemblies as well as required replacement parts
should be as follows:
a. Rejected parts should be tagged and scrapped per FAA requirements and parts
deemed unairworthy must be rendered unusable prior to discard.
b. Rectifiers and PCB components may be considered hazardous waste and
should be discarded whole through your local hazardous waste management
system.
24-30-01 ES1032
Page: 1-6
Aircraft Alternator
Owners Manual
1.8. Model Identification
ES-6904 Gear Driven (24 Volt)
1.9. Serial number Identification
HET H- O 05 0001
Year Code
Month Code
Batch Code
Example above: HET, 2014, May, first unit of the month (batch)
Year Code: O = 2014, P = 2015, Q = 2016, etc.
1.10 Warranties
A. Hartzell Engine Technologies LLC (HET) offers a Limited warranty with each new alternator
assembly or component (part) it sells through it’s distribution system. NO expressed or
implied warranty exists when repairing, or replacing any assembly or component
using this manual except as it may apply to a new HET replacement part purchased.
If you suspect that any warranty applies to the alternator assembly, it must be returned
through an authorized HET distributor in a manner prescribed by that specific distributor.
The affected alternator must be received by the factory fully assembled and not altered
in any way for disposition by HET warranty department. (Warranty shall be denied for
any alternator received altered, modified, or disassembled.)
B. The HET Limited warranty policy in affect for your alternator is determined at the time of
purchase. (As the Warranty policy is revised from time to time, you must download the
policy in affect for your unit for specific terms and conditions should a warranty condition
occur. Only the terms and conditions stated in the warranty at the time of purchase will
apply. For warranty information, visit our website at http://www.hartzell.aero/warranty/.)
ES1032 24-30-01
Page: 1-7
Aircraft Alternator
Owners Manual
24-30-01 ES1032
Page: 1-8
Aircraft Alternator
Owners Manual
DESCRIPTION OF OPERATION
2.0 GENERAL
A. Hartzell Engine Technologies (HET) direct drive alternators have been designed and
constructed to provide extended periods of trouble-free operation with a minimum
amount of maintenance. They are designed to supply a large electrical load variation and
are intended to withstand normal vibration and temperature changes encountered in
aircraft applications.
B. The ES-6904 is an isolated ground device, meaning the case of the machine does not
carry return current. A dedicated ground terminal (negative) carries all return current flow
for the unit.
2.1 BASIC COMPONENT DESCRIPTION
A. The principle components of the aircraft alternators described in this manual are the slip
ring end housing assembly with bearing, the rectifier assembly, the stator, the rotor, the
drive end housing with bearing and the brush holder assembly with spring and brushes.
B. A simplified electrical diagram, which shows the basic electrical operating points and
connections, is shown in Figure 2.1.
Figure 2.1
Alternator Simplified Electrical Diagram, Wye Connected Stator
2.2 TECHNICAL PURPOSE

A. The purpose of the alternator is to produce electrical energy. This energy is used to
maintain the proper state of charge in the battery and supply current to the electrically
powered equipment and accessories in the aircraft. It performs this function by
converting mechanical energy derived from its rotating parts into electricity.
(1) The BATTERY is the source of electrical power whenever the BAT Master Switch is ON
and is the normal source of power for starting the aircraft. The ALTERNATOR can
supply electrical power whenever the engine is running and the ALT Switch is turned
ON. (Control systems may vary with the aircraft/rotorcraft.)
ES1032 24-30-01
Page: 2-1
Aircraft Alternator
Owners Manual
2.3 PHYSICAL DETAIL

A. The brush holder assembly consists of a brush holder housing and two brush assemblies.
The brush assemblies are made from a carbon-graphite brush having a flexible braided
copper wire lead fitted to a coil spring. Each brush is electrically connected to a separate
terminal stud mounted in the brush holder housing. These studs are the F1 and F2
terminals. The brush holder assembly is mounted in the SRE housing in a position and
manner that allows one brush to ride on each ring of the rotor slip ring assembly providing
for a continuous sliding electrical connection while the rotor spins.
B. The rotor assembly is composed of a shaft, two pole-shoes, a coil assembly and a slip ring
assembly. The coil assembly is a simple enameled-wire coil wound on a bobbin form. The
coil is fitted between two iron pole-shoes which serve as magnetic flux guides. The rotor
shaft is pressed through the pole-shoes forming a heavy interference fit making a
permanent assembly fixing the poles in place on the shaft. The slip ring assembly is
composed of two copper rings mounted on a non-metallic, insulating hub. The hub is fixed
to the rotor shaft with one ring electrically connected to each end of the coil winding.
(1) The drive spline (coupling to engine) is integral to the rotor shaft and is part of the rotor
assembly. The shaft of the rotor contains a specific “shear” section which will break
upon any overload produced by the alternator or engine. It provides protection to the
engine accessory gear box.
C. The stator assembly is formed by
winding three separate coils of
enameled copper wire on a common
laminated iron core. The coils are
symmetrically spaced around the
core and overlap one another. Slot
insulators are used to protect the
windings from abrasion damage due
to contact with the core. For Wye-
connected stators, one end of each
c o i l is joined in a common
connection. The opposite ends of
each coil remain free, resulting in
four leads emanating from the stator
assembly. These leads are Figure 2.2 Stator Wiring Diagram (Typical).
electrically connected to the bridge
rectifier network.
D. A full-wave bridge rectifier is formed from discrete positive and negative diodes mounted
within the alternator. The positive rectifiers are installed in a crescent-shaped aluminum
heat sink. The mechanical connection between the rectifier casings and the heat sink
forms the positive electrical connection for the bridge leaving the heat-sink electrically
energized. As such, the heat sink is mounted in a manner that keeps it electrically
isolated from the alternator housings. The alternator's battery terminal (B+) is
mechanically and electrically connected to the heat sink. The negative rectifiers are also
installed in a separate crescent-shaped aluminum heat sink. The mechanical connection
between the rectifier casings and the heat sink forms the negative electrical connection for
the bridge. The alternator's negative terminal is mechanically and electrically connected
to the heat sink.
24-30-01 ES1032
Page: 2-2
Aircraft Alternator
Owners Manual
2.3 PHYSICAL DETAIL (cont’d)

E. The rotor assembly is supported by bearings at either end allowing the rotor to spin freely.
The bearings are mounted in the DE and SRE housings. The stator assembly is so
arranged within the DE and SRE housings as to align concentrically with the rotor
assembly. The laminated iron core of the stator assembly surrounds the pole-shoes of the
rotor assembly. The slip rings align with the brushes so as to allow one brush to contact
one ring. See Figure 2.3.
Fig. 2.3 - Typical Alternator Cutaway (Basic Components)
2.4 THEORY OF OPERATION

A. Power to drive the alternator is derived from the aircraft powerplant by means of an
accessory drive pad. Torque in transmitted though the drive to the alternator rotor shaft
resulting in rotor rotation.
B. During operation, the F1 terminal is electrically excited by an external voltage regulator.
The F2 terminal is externally connected to the aircraft electrical system ground or the ACU.
As current flows through the rotor coil a magnetic field is created with lines of flux being
concentrated between the pole-shoe fingers. As the rotor turns these lines of flux are
swept over the stationary stator coil windings inducing an alternating current flow within
them. This three-phase alternating current is conducted to the bridge rectifier circuit which
converts the alternating current to direct current. This rectified, DC current is made
available to external loads via the +B terminal.
ES1032 24-30-01
Page: 2-3
Aircraft Alternator
Owners Manual
2.5 SELF EXCITATION

A. The HET alternator model ES-6904 is not rated as self-exciting.
2.6 OPERATIONAL DATA
Table 2.1 - Operational Specifications
Alternator Model ES-6904

Drive Type Direct
Cooling Internal-Fan
Temp Range (F) up to +240˚ F
Temp Range (C) up to + 116˚ C
Min Regulation Speed 2,500 RPM
Max Continuous Speed 10,000 RPM
Voltage, Bus 24 volt
Voltage, Rated 28 volt
Current, Rated 120 Amp
Rated Altitude (feet) 31,900 feet MSL
Rated Altitude (meter) 9,723 meters MSL
Weight (lbs / kgs) 14.0 lbs (6.35 kgs)
Field Type Isolated
Filter Type None
Field Resistance 6.5-7.5 ohm 25˚ C
24-30-01 ES1032
Page: 2-4
Aircraft Alternator
Owners Manual
2.7 APPEARANCE
A. Features - ES-6904
Thru Bolts (4)
O-Rings
Cooling Air
(Inlet)
Ground Connections
(Not for electrical return.)
Spline Drive Shaft Cooling Air Figure 2.4a - ES-6904
with Shear Section (Exhaust) Front View
Field (F1 & F2)

Terminals
Figure 2.4b - ES-6904

Output (+) Rear View
Terminal Negative (-)
Terminal
ES1032 24-30-01
Page: 2-5
Aircraft Alternator
Owners Manual
24-30-01 ES1032
Page: 2-6
Aircraft Alternator
Owners Manual
TROUBLESHOOTING
3.0 General
A. In the event of a malfunction in electrical power, an alternator fault should not be assumed
before employing proper troubleshooting procedures. The objective in troubleshooting is to
find the cause of trouble and take corrective action to prevent a recurrence. Even perfectly
operational alternators cannot compensate for improper adjustments, corroded or worn
parts, improper installation or lack of maintenance.
B. This section provides general troubleshooting procedures for the alternator assembly for
unscheduled maintenance and for possible fault detection prior to maintenance activity. It
gives procedures to follow to determine the best course of action prior to disassembly. Block
type troubleshooting charts are also provided. Upon determination of fault(s), refer to the
TESTING (section 5) for applicable test procedure(s).
3.1 Procedure
WARNING:
WHEN SERVICING, REPAIRING, OR OVERHAULING THE ALTERNATOR,
CAUTION MUST BE TAKEN TO AVOID HAZARDOUS SITUATIONS. THE
ALTERNATOR, WHEN MOUNTED ON AN AIRCRAFT OR ROTORCRAFT,
PRESENTS A PHYSICAL HAZARD FROM PROPELLERS, ROTORS AND
OTHER ROTATING DEVICES. THE ALTERNATOR PRODUCES A HIGH
ELECTRICAL CURRENT OUTPUT AND ALSO PRESENTS AN ELECTRICAL
SHOCK HAZARD THAT CAN RESULT IN SERIOUS INJURY IF PROCE-
DURES IN THIS MANUAL OR THE AIRCRAFT/ROTORCRAFT SERVICE
MANUALS ARE NOT FOLLOWED.
CAUTION:
IT IS REQUIRED TO REFERENCE THE AIRCRAFT OR ROTORCRAFT AFM
OR POH AS WELL AS THE APPLICABLE SERVICE OR MAINTENANCE
MANUAL AS REQUIRED.
A. The Charts on the following pages represent potential faults in an alternator. Choose the
applicable symptom and follow the trouble shooting chart flow. Below each chart is a
discussion of each point.
3.1. Low or No Output.

3.2. Battery is Discharged.
3.3. Battery is Overcharged.
3.4. Noisy in Operation (acoustic).
3.5. Noisy in Operation (electrical).
3.6. Ammeter Erratic or Lights Flicker.
ES1032 24-30-01
Page: 3-1
Aircraft Alternator
Owners Manual
3.2 Troubleshooting Charts
Table 3.1
Loose terminal connections: Inspect the terminals and tighten if possible. If not the alternator may need to be
disassembled to replace studs or receptacles. Also observe the wire terminal ends to assure they are crimped
properly on the wire with no corrosion or burns present. If disassembly is required, replace or overhaul alternator.
Worn or broken brushes: Remove and examine brush material, spring, and leads. If spring in broken or the lead
is coming out of brush, or if brush is chipped or worn past 50% replace brush.
Dirty or worn rotor slip rings: If dirty, the slip rings may be cleaned. Take care not to scratch the surface. If the
slip rings appear worn or have grooves, replace or overhaul alternator (see section 6, Maintenance).
Short or leakage from field terminals to housing: Unless it is determined the wire terminal is shorting to the
housing, replace the field terminals and insulators. If disassembly is required, replace or overhaul alternator.
Shorted or open rotor field: Perform the tests for rotors per section 5, Testing. Rotor removal may be required
to verify the symptom. Replace or overhaul alternator (no repairs allowed on rotors).
Shorted or open stator windings: Perform the alternator tests per section 5, Testing. Stator removal may be
required to verify the symptom. Replace or overhaul alternator if failed (no repairs allowed on stators).
Shorted or open rectifier on heat sinks: Low or erratic output indicate failed rectifiers. Tests for rectifiers
(positive and negative) require disassembly. Replace or overhaul alternator.
Shorted or leaking RFI capacitor (airframe, engine, HET external filter): Remove capacitor and perform
capacitance check and wire lead to case resistance check. Replace filter capacitor if failed (external filter only).
24-30-01 ES1032
Page: 3-2
Aircraft Alternator
Owners Manual
3.2 Troubleshooting Charts (cont’d)
Table 3.2
Drive Spline Broken: Inspect the condition of the drive spline. (as applicable) The alternator must be removed
to check for this condition.
Field circuit resistance too high: Check wiring and terminal ends and repair as necessary. Check condition of
the slip rings and clean. Check rotors per section 5, Testing and if failed, replace or overhaul alternator.
Voltage regulator malfunction: Check the voltage regulator per the aircraft service manual and adjust if
necessary. If adjustment is not possible, check wiring and replace voltage regulator.
Accessory load too high for alternator rating: Refer to the AFM or POH (and aircraft service manual) for the
maximum allowable load specification. Reduce electrical load to meet these limitations.
Corroded or loose battery cable connector clamps: If connections to the battery are corroded, disconnect and
clean. Clean battery posts or terminals. If aluminum cable is installed, make sure that corrosion has not spread
under the insulation. If severe, replace cables or clamps. Tighten battery connections.
Low field voltage: Check the voltage regulator per the aircraft service manual and adjust if necessary. If
adjustment is not possible, check wiring and replace voltage regulator.
Needs battery maintenance: Perform normal battery maintenance. Check water level and electrolyte condition,
service per the aircraft service manual.
Failed battery: Determine battery age and check for expected life. If near or beyond normal life, replace battery.
If battery discharges frequently, check for dead or shorted cells, if found replace battery.
ES1032 24-30-01
Page: 3-3
Aircraft Alternator
Owners Manual
Table 3.3
Voltage regulator set too high for aircraft operating conditions: Check the voltage regulator setting per the
aircraft service manual. Adjust if necessary. If adjustment is not possible, check the wiring harness before
replacing the voltage regulator.
Ground wire loose or broken between regulator and alternator: If wire is broken, make sure there is
adequate strain relief and clear chaffing areas. Repair or replace wire. If loose, tighten connection.
Shorted cell in battery causing other cells to use water excessively: Remove and place battery on battery
tester to verify the condition. Replace failed battery.
Shorted voltage regulator output - full field condition: Before replacing the voltage regulator, check wiring
harness for shorts or open conditions. If harness is burnt or shows signs of overheating, replace harness. If,
wiring is good replace voltage regulator.
Voltage drop in voltage regulator feedback circuit: The “feedback” line is commonly known as the sense line.
Before replacing the voltage regulator, check sense line wire for resistive or short conditions. Check terminal
connections, Replace or repair wire if failed. If, wiring is good replace voltage regulator.
Alternator output above rating: As output is related to alternator speed, check that the proper alternator has
been installed. Check airplane records to determine that the proper alternator model and rating is installed per the
aircraft TC or STC.
24-30-01 ES1032
Page: 3-4
Aircraft Alternator
Owners Manual
Table 3.4
Failed bearing: To perform a test for failed bearings, hold the alternator in one hand and snap-spin the shaft with
the other. A failed bearing will be heard or felt. Replace the bearing by overhaul or replacement of the alternator.
Drive spline broken: Inspect the condition of the drive spline. (as applicable) The alternator must be removed to
check for this condition.
Debris in the cooling fan: Check alternator cooling fan to see if debris have entered the alternator housing and
are rubbing internally.
Loose rear housing or improperly installed stator: Examine through bolts. If loose and distorted or severe
“smoking” or black areas appear at the head of the bolt, the alternator should be overhauled or replaced.
Loose mounting bolts: Inspect mount points for damage and if found overhaul the alternator. If not, re-torque
mounting bolts per the engine or aircraft service manual.
Loose cooling duct connection: If cooling duct is installed incorrectly (normally an airframe component), adjust
and tighten the mounting connection (as applicable). Check and clear any interference with the airframe structure.
Interference from airframe components or structure: Examine the alternator and large electrical cables for
contact or chaffing on airframe structure. Check and clear any interference areas.
ES1032 24-30-01
Page: 3-5
Aircraft Alternator
Owners Manual
Table 3.5
Shorted rectifier (magnetic noise): Magnetic (radio) noise indicates failed rectifiers. Tests for rectifiers (posi-
tive and negative) require disassembly. Replace or overhaul alternator.
Insufficient output filtering: Check the RFI filter by performing a capacitance check. Replace RFI filter if
failed (external filter only). In some cases, additional RFI filters may be installed. Be sure that a check is performed
on each. If only one RFI filter is installed, additional filters may be required to reduce noise.
Brush arcing: Remove and examine brush material, spring, and leads. If the spring is broken or the lead is
coming out of brush, replace brush. If the brush is chipped or worn past 50%, replace brush. Examine slip ring
surface for condition and clean as required.
Rough or damaged slip ring surface: If the slip rings show minor surface roughness they may be polished. If
the slip rings appear worn or have grooves, replace or overhaul alternator (see section 6, Maintenance).
Loose field or output terminal connections: Check terminal connections for damage. Provide adequate strain
relief to the wiring and tighten terminals properly.
Loose negative, ground, or battery connections: Check negative, ground & battery connections for damage.
Provide adequate strain relief to the cables and tighten properly. (See engine or aircraft service manuals.)
Resistive or arcing circuit breaker: Make a resistance check of the circuit breaker. There should be no
resistance. Check breaker function. Old circuit breakers should be replaced.
Failed voltage regulator or connector: Check to see if the regulator connector is attached properly. Remove
and examine connector. Look for arcing or overheating. Check wiring harness and replace the voltage regulator
if failed.
24-30-01 ES1032
Page: 3-6
Aircraft Alternator
Owners Manual
Table 3.6
Dirty or oxidized regulator contacts: Inspect both the male and female connector contacts. Clean using an
aviation quality contact cleaner. For circuit board edge contacts, first us a pencil eraser on the edge followed by
contact spray cleaner.
Loose connections in charging system or damaged wiring harness: Inspect the terminals and tighten if
possible. Also examine the wire terminal ends to assure they are crimped properly on the wire and no corrosion
or burns are present. Check harness from end to end and repair any damaged wiring.
Damaged alternator or voltage regulator wiring harness: Check alternator and regulator wiring harness for
damage and repair. If wiring damage is found, check voltage regulator for function and replace if necessary.
Dirty or rough rotor slip rings: Take care not to scratch the surface. If the slip rings appear worn or have
grooves, replace or overhaul alternator (see section 6, Maintenance).
Partially shorted rectifier: Flickering lights or erratic ammeter indication due to failed rectifiers. Tests for
rectifiers (positive and negative) require disassembly. Replace or overhaul alternator.
Insufficient output filtering: Check the RFI filter by performing a capacitance check. Replace RFI filter if
failed (external filter only). In some cases, additional RFI filters may be installed, be sure that a check is performed
on each. If only one RFI filter is installed, additional filters may be required to reduce noise.
Resistive or arcing circuit breaker: Make a resistance check of the circuit breaker. There should be no
resistance. Check breaker function. Old circuit breakers should be replaced.
Loose electrical bus connections: Check aircraft electrical bus for loose wire connections. Tighten or repair as
required.
ES1032 24-30-01
Page: 3-7
Aircraft Alternator
Owners Manual
24-30-01 ES1032
Page: 3-8
Aircraft Alternator
Owners Manual
CHECK
4.0 General
A. This section defines the various checks and inspections needed to assure reliable and safe
operation of the alternator while in service. They are listed in hours time in service (TIS) or
in calendar time, whichever is applicable and are the first to occur when offered a choice.
Some maintenance is one time initial and others are recurring.
B. HET recommended maintenance and checks including TIS may be superseded by the aircraft
or engine manufacturer’s established time limits and schedules based on experience
and/or unique requirements under engine or airframe Type Certificate.
4.1 Inspection Checks (alternators in this manual)
A. 100 Hours TIS & each 100 hours thereafter. (or each annual/event, the first to occur)
(1) Perform a check of the alternator assembly. Note through bolt security and proper safety
wire application and re-torque bolts if found loose.
(2) Check the alternator to engine V-clamp nut security. If T-bolt safety wire is loose, check
nut for proper torque per aircraft, rotorcraft and/or engine maintenance manual.
(3) Inspect area around the brush holder for soot. If a large amount of soot appears, remove
brush holder and check for wear or damaged brushes.
(4) If wear has occurred, check slip rings for gouges or scratches.
(5) Check electrical terminal hardware for tightness and insulators for condition.
B. 500 Hours TIS & each 500 hours thereafter. (or each two years, the first to occur)
(1) Remove brush holder and check each brush for wear or damage. If brush shows more
than 50% wear or has chips or damage, replace brushes (brushes must be replaced as a
set only). New brushes are 0.50 inch (12.7 mm) long.
(2) With the alternator removed, check the alternator to engine V-band clamp and nut for
cracks or damage. Check the T-bolt for wear or cracks at the tee section and replace the
V-band clamp if necessary.
(3) Examine the alternator insulators and replace if cracked, deformed, or indications of
thermal distress are observed.
(4) Inspect the aluminum housing for surface corrosion, clean as necessary.
(5) Inspect the housings for cracks around the through bolt holes and ears. Replace the
housings if necessary.
(6) Clean the spline thoroughly prior to installing the alternator.
(7) Install V-band clamp and nut.
(8) Torque T-bolt nut per Table 6.1 unless superseded by the OEM’s applicable service
information or maintenance manual and safety wire.
C. TBO Coincident with engine TBO
(1) Overhaul or replacement is based on the condition of the alternator but shall not exceed
12 (twelve) calender years regardless of operating time in service.
Overhaul time may vary based on cooling, electrical load, and general service. When
published, the aircraft OEM TBO shall supersede this HET recommendation.
ES1032 24-30-01
Page: 4-1
Aircraft Alternator
Owners Manual
24-30-01 ES1032
Page: 4-2
Aircraft Alternator
Owners Manual
INSPECTION AND TESTING
5.0 General
A. This chapter outlines the tests and inspections required to determine the condition of the
alternator removed for scheduled and unscheduled maintenance. Refer to the procedures
given in the TROUBLESHOOTING Section prior to applying any test for maintenance.
B. Where applicable, components called out this section will correspond to the item number
listed in MAINTENANCE Section 6.
5.1 Testing
A. Equipment
(1) Standard tools

- Standard mechanic's handtools.
- Torque wrench ounce-inch (gram-centimeter).
- Torque wrench pound-foot (newton-meter).
- Safety gloves.
- Protective goggles (eye protection).
- Ear Plugs (hearing protection).
- Safety shoes.
- Protective cotton apron.
- Air compressor (shop air).
(2) Special tools

Standard and special tools used in this chapter are limited.
- Voltmeter (0 to 30 VDC)
- Ammeter, 0 to 200 Amp.
- Carbon Pile (or equivalent).
- Alternator test bench (12/24 volt, 0 - 200 A). (if removed to test)
(3) Instruments
- A multimeter, (Simpson 260 or Fluke 87) or equivalent (accuracy 2%).

- Optical tachometer.
B. Test conditions
(1) Ambient temperature: 70 to 80 o F (21 to 27 o C).
ES1032 24-30-01
Page: 5-1
Aircraft Alternator
Owners Manual
5.1 Testing (cont’d)

C. Precautions
Regular maintenance must be accomplished per this manual and per the applicable
aircraft and/or engine service manuals and publications. In addition, observe the following
precautions:
(1) DISCONNECT THE BATTERY before connecting or disconnecting test instruments

(except voltmeter), or before removing or replacing any unit or wiring. Accidental
grounding or shorting at the regulator, alternator, ammeter or accessories, will cause
severe damage to the units and/or wiring.
(2) DO NOT REMOVE THE OUTPUT LEAD. The output lead must not be removed
from the alternator while the rotor winding is energized and the alternator is
operating.
(3) DO NOT GROUND THE OUTPUT TERMINAL. Grounding of the alternator output
terminal may damage the alternator and/or aircraft electrical circuit.
(4) DO NOT REVERSE BATTERY CONNECTIONS. Reversed battery connections

may damage the rectifiers, aircraft wiring or other components of the charging
system. Battery polarity should be checked with a voltmeter before connecting the
battery.
(5) ASSURE PROPER CONNECTIONS TO THE BATTERY. If a booster-battery or

fast-charger is used, its polarity must be connected correctly to prevent damage to
the electrical system components.
(6) DO NOT ALLOW IMPACT CONTACT WITH DRIVE SPLINE. The shear section
of the input shaft can be damaged if exposed to impact loads.
24-30-01 ES1032
Page: 5-2
Aircraft Alternator
Owners Manual
5.2 Testing & Inspection

A. Arc Marks on Terminals (Visual Inspection):
(1) Before removing the alternator, the threads and each terminal stud should be inspected
for signs of arcing.
(2) Arc marks are usually caused by a loose wire terminal connection resulting from failure
to tighten the attaching nut.
(3) Arc marks can also be caused by improper service techniques that permit wires to be
connected and disconnected while current is flowing. A loose connection at the alternator
output (battery) terminal can erode completely through the terminal stud over time.
(4) Diode damage can occur because of the inductive voltage spikes generated by the
make and break of loose terminal connections. The positive and negative rectifiers
must be replaced at next alternator repair or overhaul.
(5) Voltage regulator and mechanical field relay damage can also be expected due to
the chattering contacts each time the loose connection makes or breaks. Chattering
contacts that are excessive will result in rapid contact erosion.
(6) Solid state field relays will not be damaged, however they may generate electrical
noise.
B. Bearing Inspection (For Troubleshooting Purposes):

(1) A simple bearing test should be performed regardless of the reason for alternator
removal from the engine. The alternator must be removed for this test. The purpose
of the test is to determine if either of the bearings are a potential for noise or failure.
(2) To perform a test for faulty bearings, with the alternator in one hand, oriented with
the shaft horizontal, snap-spin the shaft with the other. A defective bearing will be
heard or felt. Snap-spin the shaft a few times to verify.
(3) Grasp the drive spline (rotor shaft) and push-pull the shaft in a direction parallel to the
axis. Movement should be less than .0062 inch (.1575 mm).
(4) Grasp the drive spline (rotor shaft) and push-pull the shaft in a direction that is
perpendicular to the axis. Movement should be less than .001 inch (.025 mm).
(5) If either bearing sounds noisy, movement is not smooth, or excessive movement (axial
or radial) is observed, the alternator should be repaired, overhauled, or replaced.
C. Field Circuit Open or Ground Test Procedure:

(1) Using a multimeter on low range scale (0 to 25 ohm), connect one lead of ohmmeter
to the “F1” terminal and the other lead to “F2” terminal with the “F1” and “F2” terminals
isolated from the aircraft electrical system.
(2) Spin the output shaft and note ohmmeter reading. Meter should read between 7 and
20 ohms while rotor is turning.
(3) A reading lower than 3.5 ohms indicates either a grounded field terminal or a failed
rotor. Field repair or send alternator for repair, overhaul, or replacement.
(4) A reading higher than 20 ohms indicates: either worn out or hung brushes, an open
brush lead or a failed rotor.
(5) Items (2) and (3) reading may be addressed by replacement of the brushes or the
brush holder assembly. Refer to section 6.6 (Maintenance) for brushes.
(6) Item (3 & 4) failed rotor requires overhaul or replacement of the alternator.
ES1032 24-30-01
Page: 5-3
Aircraft Alternator
Owners Manual
5.2 Testing & Inspection (cont’d)

D. Mounting Hardware:
(1) Inspect and replace any removed metallic hardware, i.e., screws, flat washers, nuts,
shaft spacer, shaft woodruff key, etc., exhibiting damage, wear, corrosion, or distortion.
(2) Hardware that will be reused shall be cleaned as necessary using a non-corrosive
chemical degreaser. Air-dry parts with filtered dry low pressure compressed air or
wipe dry with clean, lint free cloth.
E. Insulators (Washers and Spacers):
(1) Inspect parts for cracks, deformation, and burn marks.
(2) Parts that are suitable for reuse shall be cleaned as necessary using isopropyl alcohol.
Any other cleaner may damage insulators. Air-dry parts with filtered dry low pressure
compressed air or wipe dry with clean, lint free cloth.
(3) Cracked, deformed, or failed insulators require replacement or overhaul of the alterna-
tor as it must be disassembled to replace damaged parts.
F. Brush holder, Brushes and Springs:
(1) Inspect brush holder for cracks or breaks and brushes for condition.
(2) If damaged, discard the brush holder assembly and replace with new.
(3) If brushes are excessively worn or damaged in any way, replace brushes in pairs
with new. Never attempt to replace a single brush.
(4) New brushes are 0.50 inch (12.7 mm) long and must be replaced if worn below 0.25
inch (6.35 mm).
G. Drive Spline:
(1) Clean spline with mild solvent to remove oil and debris. (Cleaning procedures found
in the engine manufacturers maintenance manual shall supersede this procedure.)
(2) Visually inspect spline for wear or indications of spalling or abrasion. Erosion should
not exceed 0.020 inch (0.508 mm) on any tooth flank.
(3) Inspect shear section under lighted, 3X magnification for indications of cracks.
(Refer to Figure 6.1 for shear section location on the rotor shaft.)
(4) Failure of 2 or 3 above require replacement of the alternator.
24-30-01 ES1032
Page: 5-4
Aircraft Alternator
Owners Manual
5.3 Alternator Bench Testing

CAUTION 1:
TEST BENCH PROCEDURES MUST BE PERFORMED BY APPROPRIATELY
RATED MECHANICS IN AN ADEQUATELY EQUIPPED FACILITY. PRIOR TO
BEGINNING THESE PROCEDURES, REFER TO AND OBSERVE THE
PRECAUTIONS LISTED IN TESTING SECTION 5.1(C).
CAUTION 2:
NO SIDE LOADS MAY BE APPLIED TO THE DRIVE SHAFT DURING TEST
OPERATIONS. IF NOT OBSERVED, ALTERNATOR FAILURE AND OTHER
EQUIPMENT DAMAGE MAY OCCUR.
A Alternator Output Test Conditions:

The preferred method of testing the alternator is by a commercially available alternator test
bench (rated 28 volt, 0 - 140 A), however the procedures below are considered adequate
for testing purposes. A special drive stand adapter will be required to test the alternator.
(1) The alternator is to be at room temperature 70-80 degrees Fahrenheit (21-27 degrees
Celsius) before beginning the test.
(2) The alternator is to be connected so that it is supplying its own field current.
(3) The output is to be controlled by an adjustable load.
(4) The alternator is not to be run for longer than 30 seconds for each test point.
B Test Set Up:
(1) Manufacture and connect the test set up as shown in Figure 5.1.
(2) This consists of a battery (24 volt DC, 50 ah min.), common carbon pile, test voltmeter
(0-28 VDC), test ammeter (0-140 amp), and an appropriate length of jumper wire.
(3) Prepare to use an optical tachometer to observe RPM. (per manufacturers instruction)
Jumper Wires
Carbon Pile
Test
Ammeter
rO g
Ai olin
ut
Co
Ai ling
n
o
rI
Test Voltmeter
Co
Figure 5.1 - Typical Bench Testing Set Up.
ES1032 24-30-01
Page: 5-5
Aircraft Alternator
Owners Manual
5.3 Alternator Bench Testing (cont’d)

C. Ventilation:
WARNING:
DIRECT DRIVE ALTERNATORS REQUIRE A SOURCE OF
VENTILATION. DO NOT TEST THESE ALTERNATORS IN
AN ENCLOSED SPACE AT FULL RATED OUTPUT FOR
MORE THAN 30 SECONDS UNLESS A COOLING AIR
SOURCE IS SUPPLIED. FAILURE TO VENTILATE MAY
CAUSE EQUIPMENT DAMAGE WHICH MAY RESULT IN
INJURY OR DEATH.
(1) The alternator is cooled entirely by air pressure through hose type connections on
the drive end and slip ring end housings. When bench testing this type of alternator,
make output tests as short as possible unless adequate air pressure for cooling is
supplied (3” H2O minimum delta pressure across the unit).
(2) Adjust the carbon pile to obtain the specified voltage (refer to Table 5.1). After
bench testing the alternator, install the safety wire in the through bolts. The alternator
is now ready for installation on the engine. Always refer to the aircraft manufacturer's
wiring diagram when installing the alternator or testing the alternator on the aircraft.
D. Test Procedures:
(1) Adjust the carbon pile as necessary to obtain the specified voltage shown in Table 5.1.
WARNING:
EXCEEDING THE BATTERY VOLTAGE RATING MAY DAMAGE
THE BATTERY OR CAUSE AN EXPLOSION. THIS MAY
RESULT IN INJURY, BURNS, AND EQUIPMENT DAMAGE.
(2) Apply power while observing the voltmeter, observe RPM using the optical
tachometer and the output current on the ammeter.
(3) Vary the RPM while maintaining 28.7 volts DC. Observe the amperage at each RPM.
At each RPM, the Min. Output Amps must be achieved as specified in Table 5.1.
(4) If alternator is to be reinstalled, refer to section 6.12 (Installation on Aircraft).
24-30-01 ES1032
Page: 5-6
Aircraft Alternator
Owners Manual
E. Alternator Output Test Specifications (Without Regulator)
Alternator Series: ES-6904
Output Voltage Min. Output Amps Max Alternator RPM
28.7 ± .4 Vdc 18 2500 ± 50

28.7 ± .4 Vdc 101 4000 ± 50
28.7 ± .4 Vdc 125 5000 ± 50
Table 5.1 - Output Test Specifications
ES1032 24-30-01
Page: 5-7
Aircraft Alternator
Owners Manual
24-30-01 ES1032
Page: 5-8
Aircraft Alternator
Owners Manual
MAINTENANCE
6.0 General
A. This section contains information regarding recommended maintenance for all alternators
listed in this manual. These recommendations assure reliable and safe operation of the
alternator while in service. Maintenance is listed in hours time in service (TIS) or calendar
time, whichever is applicable but each are the first to occur. Some maintenance is one time
initial and others are recurring. Refer to Chapter 4, “Checks” for required inspections.
B. HET recommended maintenance, checks and TIS may be superseded by the aircraft
or engine manufacturers established time limits and schedules based on experience
and/or unique requirements under it’s Type Certificate or other certifications.
6.1 Periodic Maintenance
NOTE: The aircraft and/or engine manufacturers periodic or event checks are contained in
the respective maintenance manual or service information.
A. The electrical charging system should be inspected at regular intervals, the frequency of
which should be determined by the type of service and the conditions under which the
aircraft is operated. Since many airframe related maintenance tasks directly or indirectly
affect alternator function, it is recommended that the aircraft manufacturers periodic
inspection/maintenance be followed prior to or in conjunction with any HET prescribed
alternator maintenance. These include:
(1) Battery - A battery condition and capacitance check.
(2) Wiring - An alternator circuit wiring and terminal condition check.
(3) Spline Drive - If the alternator is removed at any time, the spline should be checked
for wear of spline teeth or other damage per section 6.3. Whenever the alternator
is removed, the small shaft O-ring and larger alternator O-ring must be replaced.
(4) Operation - An operational check of the alternator after any maintenance is performed
on the aircraft or engine electrical systems. Use the appropriate AFM, POH, service
information or maintenance manual as applicable.
6.2 Torque Information
CAUTION: APPLYING TORQUE BEYOND THE VALUES SET IN TABLE 6.1 WILL SEVERELY
DAMAGE THE ALTERNATOR. EXCEEDING THESE VALUES MAY REQUIRE
OVERHAUL OR REPLACEMENT OF THE ALTERNATOR.
Table 6.1 - Torque Specifications

Reference Description Torque Value (US) Torque Value (SI)
Figure 6.1b Through Bolts 45-55 in-lbs 5.08-6.21 Nm
Figure 6.1b Nut, V-clamp T-bolt* 85 in-lbs 9.6 Nm
Figure 6.3.a Output Nut (POS)* 40-50 in-lbs 4.52-5.65 Nm
Figure 6.3.a Output Nut (NEG)* 30-40 in-lbs 3.39-4.52 Nm
Figure 6.2b Screws (Brush Holder) 11-14 in-lbs 1.24-1.58 Nm
Figure 6.3b Field Nut (F1 & F2) 6-8 in-lbs 0.68-0.90 Nm
Figure 6.3.a Ground Nut (bottom/top) 75-85 / 30-40 in-lbs 8.47-9.60 / 3.39-4.52 Nm
Figure 6.3a Ground Stud 70-85 in-lbs 7.91-9.60 Nm
* Attachment of Ground, Output Positive (+), Output Negative (-) , Field wires, or V-Band Clamp on the
engine or airframe may use above torque unless value differs from engine/airframe OEM torque. OEM
torque shall supersede HET value. Reminder, always secure the bottom nut when applying torque
to top nut to prevent over torque of bottom nut.
ES1032 24-30-01
Page: 6-1
Aircraft Alternator
Owners Manual
6.3 Alternator Spline Drive Inspection & Maintenance

A. The alternator spline drive is part of the alternator rotor and is fundamental to the
operation of the HET alternator.
B. If an alternator fault is determined, note that the HET ES-6904 alternator has a drive spline
incorporating a shear section integral to the alternator rotor. If the shear section is
overloaded it will snap and normal alternator output will cease.
(1) Check the general condition of the drive spline. (500 TIS removal of the alternator)
(2) Check condition of the spline teeth. Tooth erosion in excess of 0.020 inch (0.508 mm)
is cause for rejection. If this condition is present the alternator must be replaced or
overhauled.
(3) Check the condition of the drive spline shaft and shear section. Clean the shaft and
inspect for cracks or other damage using a 10X magnifying glass.
(4) The small shaft O-ring (P/N M8324B/1-111) and the larger alternator pilot O-ring
(P/N M8324B/1-131) must be replaced any time the alternator is being installed.
a. When installing the alternator small shaft O-ring and the larger pilot O-ring, care
must be taken not to nick or otherwise damage the O-ring as an oil leak will occur.
V-Band Clamp
Flange
Shear Section
Drive Spline
Output Shaft
Figure 6.1a - Spline Drive with Shear Section.
24-30-01 ES1032
Page: 6-2
Aircraft Alternator
Owners Manual
6.4 Removal from the Aircraft

A. To remove the alternator from a specific engine, refer to the aircraft and/or engine service
and maintenance manuals for detailed instructions.
B. General Removal
(1) Make sure all external power has been disconnected. Unless otherwise advised, gain
access and disconnect the ground (-) cable from the battery post followed by the positive
(+) terminal. Isolate and secure the ground (-) terminal.
(2) Disconnect the cable from the output negative (-) then the positive (+) terminals.
(3) Disconnect the Field wires and cable from the alternator Ground stud.
(4) Remove the safety wire or cable from the V-clamp and T-bolt and while supporting the
alternator, remove the T- bolt nut. Refer to Figure 6.1b.
Through Bolts T-Bolt Nut

(4 each) Torque Nut per
Torque bolt per Table 6.1.
Table 6.1.
V-Band
Clamp
Figure 6.1b - V-Band Clamp Attachment
CAUTION:
FAILURE TO PROPERLY SUPPORT THE ALTERNATOR MAY DAMAGE
THE SHEAR SECTION. (REF FIG. 6.1A.) AVOID SIDE LOADING THE
DRIVE SHAFT DURING ALTERNATOR REMOVAL AND INSTALLATION
(5) Spread open the V-band clamp. Be sure to hold the alternator by hand so the full weight
will not load the spline shaft. Carefully remove the alternator from the aircraft engine. .
(6) Remove the large and small “O” Rings and discard. The “O” Rings must be replaced each
time the alternator is removed.
6.5 Exterior Cleaning
A. Prior to cleaning the alternator, whether mounted on the aircraft or as removed, observe and
note condition. Look for any arcing, wear marks, fretting or other indicators of wear.
B. If mounted on an aircraft to engine, initial cleaning may be done using mineral spirits or
isopropyl alcohol under pressure. Blow dry using clean shop air.
C. If removed, initial cleaning of the alternator should be done using a shop cloth and mineral
spirits or isopropyl alcohol. Wipe dry using clean shop cloths.
ES1032 24-30-01
Page: 6-3
Aircraft Alternator
Owners Manual
6.6 Brush Brush Removal and Installation
A. Removal:
(1) Make sure aircraft battery and external power source has been disconnected.
(2) Disconnect the two top terminal nuts for F1/F2 while holding the bottom nut.
a. Temporarily insulate the terminals to prevent possible sparking. Refer to Figure 6.2a.
(3) Remove the two screws that hold the brush holder assembly in the slip ring end housing
(SRE). Refer to Figure 6.2a.
(4) Slowly remove the brush holder assembly from the SRE taking care not to drop the brushes
into the alternator (brushes are spring loaded).
a. If checking brushes only, be sure to mark and note the position and orientation of each
brush. Discard the brushes if replacing.
(5) If both brushes are not present upon removal of the brush holder, the missing brush must
be located and recovered from the alternator before proceeding.
F1 & F2 Field
Brush Holder Terminals
Screws (2 ea.)
Brush
Holder
Ass’y
Brush
Retaining
Wire Slot
Figure 6.2a- Brush Holder Location Figure 6.2b- Brush Holder Installation
Brush Position as Shown Brush Ass’y Brush Holder Ass’y Delivered

with Retaining Wire Installed
Brushes
Held Up
by Wire
Brush
Retaining
Wire Hole
Brush Brush
Curvature Slip RIng Arc Retaining Wire
Figure 6.2c- Brush Position in Holder Figure 6.2d- Brush Retaining Wire
24-30-01 ES1032
Page: 6-4
Aircraft Alternator
Owners Manual
B. Installation:
(1) Brushes must be replaced in pairs. If replacing brushes only, order two (2) each, HET
P/N ALE-13A brushes from an authorized HET distributor. HET recommends replacing the
brush holder assembly HET P/N ALU-3045BS which includes new brushes pre-installed
with a brush retaining wire installed.
(2) Install a new set of brushes, HET P/N ALE-13A into the brush holder. Place each new
brush into the brush holder.
a. Brushes must be oriented such that the axis of the curvature of the brush face is
parallel with axis of F1/F2 terminals. Refer to Fig. 6.2c.
b. If checking brushes only, be sure to return them in the same position and orientation
as removed.
c. Install a two inch, stiff 22 gage insulated wire into the hole provided in the side of the
brush holder while pushing in each brush with a soft tool like a wood or nylon dowel.
d. The wire will retain the brushes for installation of the holder. Refer to Fig. 6.2d.
(3) Install the brush holder assembly with the insulated brush retaining wire in place. Install
the two brush holder screws. Refer to Fig. 6.2b.
a. Torque the brush holder screws 11 to 14 in-lbs (1.24 to 1.58 Nm). Refer to Fig. 6.2a.
(4) Spin the shaft several rotations to check for interference between the brush holder and rotor.
(5) Remove insulated brush retaining wire from brush holder assembly. Rotate shaft in
running direction and listen for smooth operation. Refer to Figure 6.2d.
(6) If brushes were checked or changed without removing the alternator, connect the F1
and F2 wire terminals and torque 6-8 in-lbs (0.68-0.90 Nm).
(7) Restore aircraft battery and/or other power source which has been disconnected. If
alternator was removed, refer to Installation on the Aircraft, section 6.12 .
6.7 Through Bolts

The alternator through bolts are designed to retain proper torque for the life of the alternator.
Occasionally, unusual vibrations from the engine or other sources may loosen the through bolts.
This may be noticed by broken or loose safety wire or cable and may appear as a blackened area
at the through bolt head or threads. If loose, the following procedures apply:
A. Inspect the through bolt while installed. The through bolt must not be bent, cracked, or damaged.
WARNING:
LOOSE AND/OR DAMAGED THROUGH BOLTS MAY INDICATE SERIOUS
INTERNAL DAMAGE IN THE ALTERNATOR WHICH MAY RESULT IN THE
UNEXPECTED FAILURE OF THE ALTERNATOR.
B. If any through bolt is bent, cracked, damaged or housings are loose, the alternator should be
replaced or overhauled.
C. If the through bolts are not damaged but appear only to be loose, it is permissible to apply
proper torque. This may be accomplished by removing the alternator or in the aircraft as
space permits.
(1) Cut the safety wire or safety cable from the bolt head at the drive end of the alternator and
discard. Using a calibrated torque wrench in inch-pounds, apply 45-55 in-lbs (5.08-6.21
Nm) torque to the loose through bolt. After application of torque, check and apply the prop-
er torque to the remaining through bolts.
(2) Apply new 0.032 inch stainless steel safety wire or safety cable (HET P/N RX-1961)
through the drilled hole in the through bolt head at the drive end of the alternator. Refer to
section 6.10 or 6.11 as applicable.
ES1032 24-30-01
Page: 6-5
Aircraft Alternator
Owners Manual
6.8 Terminal Hardware Removal and Installation

NOTE: The alternator must be disassembled to Output Positive Terminal (+)
replace the insulator bushings and/or Top Nut -
reestablish proper bottom nut torque. Lockwasher -
Bottom Nut -
A. Removal: Lockwasher -
Flat washer -
(1) Output Positive (+) Terminal: Using a 9/16 Insulator _
inch wrench, hold the bottom nut and loosen Bushing --
the top nut as shown in Fig. 6.3a Output
Positive Terminal. This is required to prevent
the loss of factory torque of the bottom nut.
Remove & discard lockwasher.
a. Output nuts are HET P/N MS35650-3312.
b. Lockwashers are HET P/N MS35338-45. Output Negative Terminal (-)
(2) Output Negative (-) Terminal: Using a 7/16 - Top Nut
inch wrench, hold the bottom nut and loosen - Lockwasher
the top nut as shown in Fig. 6.3a Output - Bottom Nut
- Lockwasher
Negative Terminal Terminal. This is required - Flat washer
to prevent the loss of factory torque of the - Bushing
bottom nut. Remove & discard lockwasher.
a. Output nuts are HET P/N 8X-1063.
b. Lockwashers are HET P/N 12X-0199.
(3) Ground Terminal: Using a 7/16 inch wrench,
hold the bottom cupped nut and loosen the
top cupped nut shown in Fig. 6.3a GROUND Ground Connection
Stud. This is required to prevent the loss of
factory preset torque of bottom nut.
a. Ground nuts, HET P/N 40296.
b. Ground stud is HET P/N 41038.
(4) Field Terminal(s): Using a thin 5/16 in.
Cupped Nut -
wrench, hold the bottom nut and loosen the
Cupped Nut -
top nut as shown in Fig. 6.3b Field Terminal.
This is required to prevent the loss of the Stud
factory torque of the bottom nut. Remove (.125 inch Socket)
and discard lockwasher.
a. Field nuts are HET P/N 8X-0140. Figure 6.3a - Terminal Hardware Stack
b. Lockwashers are HET P/N 12X-0194.
FIELD TERMINAL
B. Installation:
(1) Output Positive (+) Terminal: Place new lock-
washer, HET P/N MS35338-45 and the existing
Output nut, HET P/N MS35650-3312 on the
Output terminal. Using a 9/16 wrench, hold the
bottom nut and tighten the top nut to a torque
of 40 to 50 in-lbs (4.52-5.65 Nm). Refer to
Fig. 6.3a Output Positive (+) Terminal.
(2) Output Negative (-) Terminal: Place new lock-
washer, HET P/N 12X-0199 and the existing Figure 6.3b - Field Terminal Hardware Stack
nut, HET P/N 8X-1063 on the output terminal.
Using a thin 7/16 inch wrench, hold the
bottom nut and tighten the top nut to a torque
of 30 to 40 in-lbs (3.39-4.52 Nm). Refer to
Fig. 6.3a Output Negative Terminal.
24-30-01 ES1032
Page: 6-6
Aircraft Alternator
Owners Manual
(3) Ground Connection: Place the existing Ground Stud cupped nut, HET P/N 40296 on the
Ground stud. Using a 7/16 inch wrench, hold the bottom cupped nut and tighten the top
cupped nut to a torque of 30 to 40 in-lbs (3.39-4.52 Nm). Refer to Fig. 6.3a GROUND Stud
terminal.
a. If the ground stud is loose, it may be replaced with a new HET P/N 41038 Stud and torqued
to 70 to 85 in-lbs (7.91-9.60 Nm) using a 1/8 inch allen wrench. Torque the bottom
cupped nut to 75 to 85 in-lbs (8.47-9.60 Nm).
(4) Field Terminal(s): Place new lockwasher, HET P/N 12X-0194 and the existing Field nut, HET
P/N 8X-0140 on the Field stud. Using a thin 5/16 in. wrench, hold the bottom nut and tighten
the top nut to a torque of 6 to 8 in-lbs (0.68-0.90 Nm). Refer to Fig. 6.3b Field Terminal.
(5) As standard practice, always apply a torque seal stripe to hardware once proper torque is
achieved.
6.9 Materials
This section presents the current materials available for maintenance. Items are available through an
HET authorized distributor and are the only parts available at this time. Some parts such as mounting
hardware, hoses, and clamps may only be available from aircraft/engine (OEM).
A. Hardware
(1) One (1) each, Nut, Positive Output (+) terminal, P/N MS35650-3312.
(2) One (1) each, Lockwasher, Positive (+) terminal, P/N MS35338-45. Replace when removed.
(3) One (1) each, Negative Output (-) terminal, P/N 8X-1063
(4) One (1) each, Lockwasher, Negative (-) HET P/N 12X-0199. Replace when removed.
(5) As required, Cupped Nut, Ground stud terminal, HET P/N 40296.
(6) As required, Ground Stud, HET P/N 41038.
(7) As required, Nut, Field terminal, HET P/N 8X-0140.
(8) As required, Lockwasher, Field terminal, HET P/N 12X-0194. Replace when removed.
B. Specific Items
(1) As required, Cover, Output Shaft, HET P/N 41044.
(1) One (1) each, Clamp, V-Band, (alternator to engine) HET P/N 41047.
C. Special Items
(1) One (1) each, O-Ring, Output Shaft, HET P/N M83248/1-111. Replace when removed.
(2) One (1) each, O-Ring, DE Housing, HET P/N M83248/1-131. Replace when removed.
(3) Two (2) each, Brush assembly, HET P/N ALE-13A.
(4) Two (2) each, Screw, Brush Holder, HET P/N 03C44209B15.
(5) One (1) each, Brush Holder assembly, HET P/N ALU-3045BS. (optional)
(Includes holder, brushes, & brush retaining wire.)
(6) As required, Safe-T-Cable™, HET P/N RX-1961. (or 0.032 inch stainless steel safety wire.)
ES1032 24-30-01
Page: 6-7
Aircraft Alternator
Owners Manual
6.10 Applying Safety Wire

A. If applying safety wire, use 0.032 stainless steel per the standards outlined in AC43.13.1b or
NASM-33540 of the latest revision. (Safety wire does not maintain fastener torque.)
6.11 Applying Safety Cable

A. If applying an HET P/N RX-1961 Safe-T-Cable™, follow the recommended procedures of
the Safe-T-Cable™, manufacturer. Applicable detailed procedures may be found on the
Safe-T-Cable™, website: http://www.dmctools.com.
(1) Use of the Safe-T-Cable™ requires the use of special tool kit DMC-1000-4R Tools and
Parts Kit for 0.032” Safe-T-Cable™.
6.12 Installation on the Aircraft

To install the alternator on the engine, refer to the applicable engine and/or aircraft service and
maintenance manuals. Always follow the OEM instructions.
General Installation
A. Make sure the aircraft battery and any external power has been disconnected.
B. Apply a drop of clean engine oil and install the small rotor shaft O-ring (P/N MS83248/1-111)
onto the alternator drive spline and the same with the larger O-ring (P/N MS83248/1-131) to
the alternator/engine DE pilot.
C. Position the alternator and install using the following procedure:
(1) Carefully align the drive splines on alternator shaft with the engine pad drive quill.
Support the alternator so as to avoid side-loading the shaft during installation.
(2) Slide shaft into accessory drive quill until the mounting flange pilot engages fully with
the accessory pad.
(3) While continuing to support the alternator, install the V-Band Clamp, position to center
the clamp vee, and tighten the T-bolt nut.
(4) Tighten the T-bolt nut to a torque of 85 in-lbs (9.16 Nm) per Table 6.1. If available, OEM
torque for the T-bolt nut shall supersede HET value.
D. Connect the Field wires, positive (+) output, negative (-) output, and ground stud cables
on the proper terminals of the alternator. Refer to section 2.4b for locations.
E. Re-connect the cooling air supply and exhaust tubes.
F. Unless otherwise advised by the OEM, connect the positive battery cable to the positive
(POS) battery terminal, then connect the aircraft ground cable to the negative (NEG) battery
terminal.
G. Check the alternator for security and make a running performance test per the AFM or POH and
the engine/aircraft service and maintenance manuals.
24-30-01 ES1032
Page: 6-8
Aircraft Alternator
Owners Manual
6.13 Special Conditions:

NOTE: For engine OEM’s Special Condition “Sudden Stoppage”, refer to the latest revision of
of the engine manufacturers maintenance manual, section 05-50-00.
A. SUDDEN ENGINE STOPPAGE:
(1) If the engine has experienced “sudden stoppage” as defined by the engine manufacturer, the
alternator may be impacted by this event. Although the alternator drive system is
designed with a shear section which protects the engine from seizure of the rotating
components inside the alternator, the drive spline may have been damaged and should be
inspected.
(2) If “sudden stoppage” as defined by the engine manufacturer has occurred, the alternator
must be removed and overhauled. Refer to the appropriate engine or airframe manuals
to remove the alternator. Item A(2)a must be performed on any sudden stoppage
and is provided for the use of qualified repair or overhaul shops.
a. If the alternator has been involved in an accident with sudden stoppage, perform
magnetic particle inspection (ASTM E 1444) to check the condition of the drive shaft.
Fluorescent penetrant inspection (FPI) is required for the remainder of the alternator
components. Use of FPI should be done per ASTM E1417 latest revision (supersedes
MIL-STD-6866).
(3) If damage is found in step A(2), all supporting bracketry, V-Band Clamp, and hardware
associated with the alternator should be inspected in accordance with the appropriate
engine or airframe manuals.
(4) Upon completion, assure all steps are taken to properly return the aircraft to service.
B. LIGHTNING STRIKE:
NOTE: For aircraft and engine OEM’s Special Condition “Lightning Strike”, refer to the latest
revision of the applicable manufacturers maintenance manual, section 05-50-00.
(1) Lightning strike is a very unpredictable event both in occurrence and in resultant
damage. A lightning bolt entry point may have many exit points or only one. On a well
bonded composite aircraft, the lightning bolt will stay on the outer surface throughout the
aircraft with little damage to components. The path of the electrical current cannot
easily be determined in most cases because while the current may surge through well
bonded areas without damage, a gap in any metal contact point or to underlying metal
structure will result in an arc, burn, or shattered composite. This is especially true for
rotating parts such as gears or shaft splines.
(2) If a report of a potential or actual lightning strike is made, inspect the aircraft for entry
and exit points for the lightning bolt to confirm that a strike has occurred. Use the engine
and/or aircraft manufacturers maintenance manuals to accomplish these tasks.
(3) If a lightning strike has occurred, (especially if burns appear on the turbine blades or
turbine spinner) remove the alternator and inspect for arc marks or burns.
a. Inspect the spline drive teeth, as an arc here may leave raised metal which will
cause further damage when running.
b. Inspect the mounting points and bracketry for arc marks or burns at joints and
attachments.
c. Inspect the alternator output and field wires. The small gage field wiring can vaporize
when exposed to lightning currents.
(4) If evidence of a strike is observed and the alternator is being overhauled or replaced due
to this evidence or due to malfunction, it is advised that the entire aircraft electrical
system be inspected. Use the appropriate engine and/or aircraft manufacturers
maintenance manuals to accomplish the task.
ES1032 24-30-01
Page: 6-9
Aircraft Alternator
Owners Manual
B. LIGHTNING STRIKE: (CONT’D)

(5) If there is no indication of arcing or other damage and a lightning strike cannot be
confirmed, reinstall the alternator and check per the applicable airframe and engine
manufacturers maintenance manual.
(6) Upon completion, test run the engine per the POH or AFM prior to returning the aircraft or
rotorcraft to service. Make an appropriate logbook entry concerning the lightning strike.
6.14 Storage and Shelf Life:

A. STORAGE:
This section addresses the storing of new, overhauled or repaired alternators.
(1) Short term storage is up to but not exceeding twenty-four (24) calendar months.
a. Short term on the shelf: requires only that the unit be kept inside in the original
packaging.
b. Short term on the aircraft (or unmounted engine): No additional action other
than that required for the engine or aircraft is needed.
(2) Long term storage is storage up to but not exceeding twelve (12) calendar years.
a. Long term on the shelf: Requires that the alternator be removed from the box and
from the plastic bag as originally packaged:
1 Discard the original bag.
2 Wipe or lightly spray outside with an electrically friendly preservative oil.
3 Place in a new bag that is specifically formulated for corrosion resistance in
the storage of metal products. (Ref. Armor Poly VCI, Armor Protective
Packaging, Howell, MI USA, www.armorvci.com or an equivalent.)
4 Place back into original shipping container and store in a cool dry environment.
b. Long term on the aircraft (or unmounted engine): If it is anticipated that the aircraft
(or unmounted engine) will be in a long term storage situation:
1 As soon as practicable, lightly spray outside with an electrically friendly
preservative oil.
2 No additional action other than that required for the engine or aircraft is needed.
B. SHELF LIFE:
(1) This alternator manufactured by HET has a shelf life of up to, but not to exceed, twelve
(12) calendar years, regardless of storage or usage. The unit must be overhauled if
this shelf life is exceeded. Shelf life time applies only if storage requirements are
observed.
24-30-01 ES1032
Page: 6-10

英文 485通讯

Uploaded by

Copyright:

Available Formats

英文 485通讯

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

英文 485通讯

Uploaded by

Copyright:

Available Formats

Hartzell Engine Technologies LLC

2900 Selma Highway

Copyright © 2016 Hartzell Engine Technologies LLC

All rights reserved. No part of this publication may be reproduced,

TABLE OF CONTENTS (Cont’d)

Phone: +1.334.386.5400, option 2

INTENTIONALLY LEFT BLANK

Revision Issue Page Inserted

New 8-04-16 N/A Original

Revision Issue Page Inserted

Record of Temporary Revisions

Record of Temporary Revisions

Service Publication List

Pub. Number Description Alternator Affected

Service Publication List

Pub. Number Description Alternator Affected

List of Effective Pages

Content of Pages Page Date of Latest Revision

Title Page - i Rev. New - 8-04-16

List of Effective Pages

Content of Pages Page Date of Latest Revision

Figure 2.2 - Stator Wiring Diagram (Typical) 2-2

Table 2.1 - Operational Specifications 2-4

Table 3.1 - Low or No Alternator Output 3-2

Table 3.2 - Battery Discharged 3-3

Table 3.3 - Battery Overcharged 3-4

Table 3.4 - Noisy Alternator (acoustic) 3-5

Table 3.5 - Noisy Alternator (electrical) 3-6

Table 3.6 - Ammeter Erratic or Lights Flicker 3-7

Table 5.1 - Output Test Specifications ES-6904 5-7

Table 6.1 - Torque Specifications 6-1

A.0 General Information

A.1 Airworthiness Limitation Statement

Airworthiness Limitation Revisions Log

AIRWORTHINESS LIMITATIONS (cont’d)

A.2 Life Limits

1.1 General Specification (manual)

1.2 How to use the manual:

Measurements are given in U.S. Units followed by SI Units in parentheses.

1.4 Units of Measure

B. U.S. Units (SI units)

ft (m) Foot (meter)

EMI: Electro Magnetic Interference. A disturbance in the radio-frequency spectrum that is

MULTIMETER: Device for the measurement of voltage, current, or resistance.

LEAKAGE: Dissipation of voltage or current from a component or connection.

RECTIFIER: An electrical circuit used to convert AC into DC current. The rectifier is a

RFI: Radio Frequency Interference. Electromagnetic energy in the radio-frequency

ROTOR: Rotating electro magnet used to create a magnetic field.

STATOR: A stationary set of conductors wound in coil form on an iron core.

TEST BENCH: Device so constructed as to allow testing of the alternator or component

VOLT/OHM METER: Device for the measurement of voltage or resistance.

1.8. Model Identification

ES-6904 Gear Driven (24 Volt)

1.9. Serial number Identification

INTENTIONALLY LEFT BLANK

2.1 BASIC COMPONENT DESCRIPTION

2.2 TECHNICAL PURPOSE

2.3 PHYSICAL DETAIL

2.3 PHYSICAL DETAIL (cont’d)

Fig. 2.3 - Typical Alternator Cutaway (Basic Components)