Stell 2011specific

Published by .
© 2011 by
5-912, Kita-Shinagawa, Shinagawa-Ku, Tokyo
141-8688 Japan
All rights reserved. No part of this book may be

reproduced, in any form or by any means, without
permission in writing from both the publisher and
editor.
The is to
provide information to assist welding personnel study
the arc welding technologies applied in specific steels
and cast irons.
Reasonable care is taken in the compilation and
publication of this textbook to insure authenticity of the
contents. No representation or warranty is made as to
the accuracy or reliability of this information.
Introduction
Arc welding is currently used for fabrication and construction of a variety of structures
such as buildings, bridges, ships, offshore structures, boilers, storage tanks, pressure vessels,
pipelines, automobiles and rolling stock. These structures use various types of steels and cast
irons suitable for their specific applications. Different metals inherently possess different
weldability. Some metals are readily weldable, but some are difficult to weld, which require
specific welding procedures. Personnel in charge of welding, therefore, should have sufficient
knowledge of the specific welding technologies required for welding specific metals in order to
fabricate and construct various structures successfully. The
has been published as a welding technology guide for studying the weldability of
specific steels and cast irons and proper welding procedures. This guidebook contains many
figures in order to help the readers understand the specific welding technologies. The
information contained in this guidebook includes those from the references listed below. This
guidebook consists of five chapters:
Chapter 1: Arc Welding of High-Strength Steel

Chapter 2: Arc Welding of Heat-Resistant Low-Alloy Steel
Chapter 3: Arc Welding of Stainless Steel
Chapter 4: Arc Welding of Cast iron
Chapter 5: Arc Welding for Hardfacing
References
(1) The Association for Training Engineers of Smaller Enterprises in Japan,
"Welding of High-Strength Steel," Utilization of Welding Technology, 1984
(2) H. Ikawa, T. Godai, "Welding of Heat-Resistant Steel and Heat-Resistant Materials,"
The Complete Book of Welding — Series 4, 1978, Sanpo Publications Inc.
(3) American Petroleum Institute, “Steels for Hydrogen Service at Elevated Temperatures and
pressures in Petroleum Refineries and Petrochemical Plants,” API Recommended Practice 941,
Fifth Edition, January 1997, Supplement 1 April 1998
(4) O. Tanaka, "Welding of Stainless Steel and Characteristics of the Welds,"
Welding Technique, 1986, The Japan Welding Engineering Society, Sanpo Publications Inc.
(5) Kobe Steel, Ltd., “Electrode Handbook,” 1964
(6) American Welding Society, “Welding Handbook,” Eighth Edition, Vol. IV, 1998; Vol. I, 1987
(7) American Welding Society, “Welding Encyclopedia,” 18th Edition, 1997
(8) J. Lancaster, “Handbook of Structural Welding,” Abington Publishing
iii
Chapter 1
Arc Welding of
High Strength Steel
Contents
1. Types and features of high strength steels 1-2
2. Weldability of high strength steels 1-7

2.1 Hardenability of welds 1-7
2.2 Weld cracks 1-9
3. Welding processes and procedures 1-16

3.1 Shielded metal arc welding 1-16
3.2 Submerged arc welding 1-23
3.3 Gas metal arc welding 1-27
3.4 Gas tungsten arc welding 1-29
Arc Welding of High-Strength Steel
1. Types and features of high-strength steels
High-strength steel is used in a variety of steel structures such as ships, bridges, buildings,
pressure vessels, storage tanks, penstocks, pipelines, autos, and rolling stock in order to allow
the steel structures to have higher design strengths. High-strength steels have higher tensile
strengths and higher yield strengths with larger yield ratios (the ratio of yield strength to
tensile strength) than mild steel, as shown in , thereby facilitating higher design
strengths. High-strength steels can be referred to as a family of steels having yield strengths
of 275 N/mm2 (28 kgf/mm2) or higher and tensile strengths of 490 N/mm2 (50 kgf/mm2) or
higher.
20
110
Fig. 1.1 — Relationship between tensile strength, yield strength, and yield
ratio of steel materials
With high-strength steels, structures can be designed to have larger scales or thinner
thicknesses due to the ability of sustaining larger applied stresses when compared with mild
steel. shows how the use of high-strength steel can make steel structures thinner or
lighter. The use of HT50 steel, for example, can reduce the weight of a steel structure by 25%
in comparison with the use of mild steel under the same design stress. The weight ratios
shown in Table 1.1 are calculated in accordance with the following formula.
1-2
Minimum yield strength of mild steel

Weight ratio =
Minimum yield strength of
high-strength steel
Table 1.1 — The possibility of weight reduction of steel structures by using high-strength steels
in comparison with mild steel under the same design strength
Min. yield strength Weight reduction
Type of steel Weight ratio
(N/mm2) ratio (%)
Mild steel (SM400A) 235 1.00 0
HT50 (SM490A) 315 0.75 25
HT58 (SM570) 450 0.52 48
HT60 (HW490) 490 0.48 52
HT80 (HW685) 685 0.34 66
Note:
(1) The minimum yield strengths of SM400A, SM490A and SM570 are those of the steel plates in
the thickness range of 16-40 mm as per JIS G 3106:2004 (Rolled Steels for Welded Structure)
(2) The minimum yield strengths of HW490 and HW685 are those of the steel plates with
a maximum thickness of 70 mm as per WES 3001:1996 (Weldable High Strength Steel Plates).
In the production of high-strength steels, the alloying elements (C, Mn, Ni, Cr, Mo, V, Nb,
Cu, Ti, B, etc.) are added and heat treatment is applied in order to provide adequate tensile
strengths, yield strengths, ductility, and notch toughness to the requirements of the relevant
standards and specifications. The heat treatment includes normalizing, normalizing and
tempering, and quenching and tempering. In addition, high-strength steels are often produced
by using specially controlled thermal and rolling sequences known as the Thermo-Mechanical
Control Process (TMCP). The TMCP steels offer higher strengths with lower carbon equivalent
and superior weldability.
High-strength steels can be classified by tensile strength (for example, 50, 60, 70, 80, and
100 kgf/mm2 classes). Some standards and specifications, however, classify high-strength
steels by yield strength. shows the JIS standard for high-strength steels in which
steels are classified by tensile strength. and show the standards for
high-strength steels classified by yield strength, which are specified by the Japan Welding
Engineering Society (JWES) and the American Petroleum Institute (API), respectively.
Some classes of high-strength steels offer superior notch toughness at low temperatures,
which are utilized for low-temperature equipment such as LPG carriers, LPG storage tanks,
and offshore structures. This type of steel is also known as low-temperature steel.
High-strength steels include special classes that offer higher corrosion resistance under the
atmospheric conditions, which are known as weatherproof steels and are utilized in bridges
and buildings constructed in industrial and seashore areas.
1-3
1-4

Stell 2011specific

Uploaded by

Copyright:

Available Formats

Stell 2011specific

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Stell 2011specific

Uploaded by

Copyright:

Available Formats

Published by .

All rights reserved. No part of this book may be

Chapter 1: Arc Welding of High-Strength Steel

1. Types and features of high strength steels 1-2

2. Weldability of high strength steels 1-7

3. Welding processes and procedures 1-16

1. Types and features of high-strength steels

Minimum yield strength of mild steel

You might also like