Control

Microsystems
is becoming
Product Data Sheet

SCADAPack33O|334
Features:
n High performance 32-Bit processor
n 10/100BaseT Ethernet port
n Two USB 2.0 compliant ports (host and peripheral)
n Configurable power saving modes (12mW in sleep mode)
n Three serial ports (RS-232, two RS-232/RS-485)
n Optional 5607 lower I/O module
n Optional integrated spread spectrum radio
n 2 or 4 run custody flow computer using RealFLO 6
n Support for 32 independent C/C++ applications
n C CSA US Class I, Division 2 Hazardous Area Rating
n CSA certified to UL508 standards
n ATEX II 3G and IECEx: Ex nA IIC T4 per EN 60079-15, protection type n (Zone 2) *
n 3-year warranty on parts and labor.

The Control Microsystems SCADAPack330|334 and an internal analog input measuring choice for applications that require low power
is the latest offering in the 300 series of incoming power supply voltage for solar operation in tandem with a varied mix of
programmable logic controllers. This controller applications. With the addition of the optional analog and digital I/O as well as multiple
packs the same I/O punch as the original 5607 lower I/O module, the SCADAPack334 communication ports. When coupled with
SCADAPack, but with the advantages of the 300 features an extra 16 digital inputs, 10 digital industry-standard Modbus and DNP
series platform, there’s more: high- outputs, 8 analog inputs and 2 analog protocols, the SCADAPack330|334
performance 32-bit processing, high speed LAN outputs, and support for Control integrates easily with ClearSCADA SCADA
and USB communication and advanced power- Microsystems Series 5000 I/O expansion management software and Vision operator
saving features – all this in the smallest modules further increases the controller's interface terminals, as well as a wide range
footprint yet. Additionally, the product has an I/O capacity and versatility. With all these of third-party SCADA software, MMIs, DCS
integrated power supply, analog and digital I/O, features, the SCADAPack330|334 is the systems, intelligent instrumentation and
serial communication capabilities, and turbine right controller for a wide variety of process remote I/O control applications.
flow meter counter inputs. The SCADAPack control and metering connections. A flexible controller that can be used in both
330|334 uses industry-standard Modbus and Flexible Communications - As with all Modbus master and slave configurations, the
DNP3 serial protocols as well as Modbus TCP SCADAPack controllers, the SCADAPack330|334 supports report-by-
and UDP-based Ethernet protocols, and can be SCADAPack330|334 offers a variety of exception and store and forward messaging
programmed locally or remotely through a communication modes making it one of the and can also make the most of DNP’s
choice of flexible programming languages. most communication-rich controllers on the advanced protocol functionality, including
Overview: market. The SCADAPack330|334 includes maintenance polling, unsolicited messaging
Compact and Powerful - The two USB2.0 compliant ports providing low and data-backfilling. For oil and gas
SCADAPack330|334Programmable Logic speed (1.5MB/s) and full speed (12MB/s) applications, the RealFLO enabled
Controller provides Remote Terminal Unit communication: a peripheral port to connect SCADAPack330|334 flow computer
(RTU) functionality with flexible the SCADAPack330|334 to PC-based furnishes two or four run custody transfer
programming options. The unit is applications, and a powered host port to options. In the water and wastewater sector,
programmable in either TelePACE Relay attach third-party hardware such as mass the SCADAPack330|334 is well suited for
Ladder Logic or the IEC 61131-3 family of storage devices (memory sticks). Two RS- use in lift and pump stations, dam control
languages and provides sophisticated 232/485 and one RS-232 serial systems and environmental monitoring
control functionality such as flow calculation communication port offer Modbus RTU, solutions. In solar powered applications the
and PID control. Additionally, up to 32 Modbus ASCII and DNP3 communication SCADAPack330|334 offers further cost
independent C/C++ applications can be protocols. For applications requiring high- reduction by allowing smaller solar panels
loaded, executed and deleted in parallel with speed Ethernet LAN or WAN communication, and batteries to be used. The overall small
standard controller logic to provide maximum a fully integrated 10/100BaseT Ethernet port footprint also enables the use of compact
flexibility and performance. The central furnishes Modbus/TCP, Modbus RTU/ASCII in mounting enclosures for those applications
processing unit includes a 32-bit UDP, DNP in TCP, DNP in UDP and ICMP (ping). where space is at a premium.
microprocessor with 16MB FLASH ROM, and For those challenging remote applications, a Similar in manufacture to all SCADAPack
4MB CMOS RAM for use in firmware and fully integrated, license-free spread products, the SCADAPack330|334 has
application programming. Custom power- spectrum wireless module is available at conformal coating, and zinc-plated steel
saving features include configurable power 900 MHz and 2.4 GHz. The system components. Regardless of the
modes, such a Reduced Power Mode and SCADAPack330|334 also supports external specific need, the SCADAPack330|334 can
Sleep Mode, and control over power radios and dial-up modem communication. provide reliable and compact stand-alone
consumption by serial/LAN/USB ports. The Applications and Benefits: performance in the hazardous environments
basic SCADAPack330 comes with 3 counter The SCADAPack330|334 is designed with so often found in SCADA applications.
inputs (including two turbine meter inputs) power conservation in mind. It’s a natural
* 334-based 24V DI/Solid State Relay version only, Wireless versions pending approval
SCADAPack 33O|334 Product Data Sheet

Specifications (P33O: 521O controller board only)

Controller
Processors CPU: 32-bit ARM7 microcontroller, 32 MHz clock, integrated watchdog timer
Microcontroller co-processor, 20 MHz clock
Memory 4 MB SRAM, 16MB flash ROM
Non Volatile CMOS SRAM with lithium battery retains contents for 2 years with no power
Datalog Capacity 465k words
I/O
Analog Inputs N/A
Counter Inputs 1, 0-10Hz or 0-5kHz (dry contact)
2, 0-10kHz (turbine or dry contact)
Communications
Serial Port COM1 RS-232 port, 8-pin modular RJ45 jack, full or half duplex, or
RS-485 port, 2-wire, half duplex
Serial Port COM2 RS-232 port, 8-pin modular RJ45 jack, full or half duplex, or
RS-485 port, 2-wire, half duplex
Serial Port COM3 RS-232 port, 8-pin modular RJ45 jack, full or half duplex with RTS/CTS control and Vision OIT
power control
Baud Rates 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, and 115200
Serial Protocols Modbus RTU, Modbus ASCII, DNP3, DF1
Serial Protocol Modes Slave, Master, Master/Slave, Store and Forward
Ethernet Port RJ45, 10/100BaseT
Ethernet Protocols Modbus TCP, Modbus RTU in UDP, Modbus ASCII in UDP, DNP in TCP, DNP in UDP
Network Protocols IP, ARP, TCP, TFTP, UDP and ICMP
USB Host Port USB 2.0 compliant “A”-type receptacle, provides up to 100mA at 5V
USB Peripheral Port USB 2.0 compliant “B”-type receptacle
Wireless1 Spread spectrum radio at 900MHz2 and 2.4GHz2
General
I/O Terminations 6-pole removable terminal block, 12 to 22AWG, 15A contacts
Dimensions 5.65 inch (144mm) wide, 5.00 inch (127mm) high, 1.80 inch (45mm) deep
Packaging Corrosion resistant zinc-plated steel with black enamel paint
Environment 5% RH to 95%, non-condensing,
– 40°F (– 40°C) to 158°F (70°C)
Power Input 11 - 30VDC, 12mW at 12V during Sleep
510mW at 12V during normal operation. 32MHz, LEDs off, no expansion, LAN and USB disabled
320mW at 12V during reduced power mode operation. 12MHz, LEDs off, no expansion,
LAN and USB disabled
1.2W at 12V during normal operation. 32MHz, LEDs off, no expansion, LAN enabled and USB disabled
Add 25 to 100mW when enabling the LEDs
8.5W at 24V maximum, 5V supply fully loaded
Warranty 3 years on parts and labor
1 Available only with optional integrated wireless modules or with stand-alone wireless modules.
2 Not applicable in all countries.
SCADAPack 33O|334 Product Data Sheet

Specifications (P334: 521O controller board and integrated 56O7 I/O board)
Controller
Processors CPU: 32-bit ARM7 microcontroller, 32 MHz clock, integrated watchdog timer
Microcontroller co-processor, 20 MHz clock
Memory 4 MB SRAM, 16MB flash ROM
Non Volatile CMOS SRAM with lithium battery retains contents for 2 years with no power
Datalog Capacity 465k words
I/O
Analog Inputs 8, 0-20/4-20mA / 0-5/0-10V (15-bit) software configurable
Analog Outputs Standard: None
2, 0-20/4-20mA (12-bit) with optional 5305 on 5607 I/O board
Digital I/O 16, 12/24V, 48V, 115/125V, 240V digital inputs
10, relay outputs (dry contact or DC solid state)
Counter Inputs 1, 0-10Hz or 0-5kHz (dry contact); 2, 0-10kHz (turbine or dry contact)
Communications
Serial Port COM1 RS-232 port, 8-pin modular RJ45 jack, full or half duplex, or
RS-485 port, 2-wire, half duplex
Serial Port COM2 RS-232 port, 8-pin modular RJ45 jack, full or half duplex, or
RS-485 port, 2-wire, half duplex
Serial Port COM3 RS-232 port, 8-pin modular RJ45 jack, full or half duplex with RTS/CTS control and Vision OIT
power control
Baud Rates 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, and 115200
Serial Protocols Modbus RTU, Modbus ASCII, DNP3, DF1
Serial Protocol Modes Slave, Master, Master/Slave, Store and Forward
Ethernet Port RJ45, 10/100BaseT
Ethernet Protocols Modbus TCP, Modbus RTU in UDP, Modbus ASCII in UDP, DNP in TCP, DNP in UDP
Network Protocols IP, ARP, TCP, TFTP, UDP and ICMP
USB Host Port USB 2.0 compliant “A”-type receptacle, provides up to 100mA at 5V
USB Peripheral Port USB 2.0 compliant “B”-type receptacle
Wireless1 Spread spectrum radio at 900MHz2 and 2.4GHz2
General
I/O Terminations 5, 6 and 9-pole removable terminal blocks, 12 to 22AWG, 15A contacts
Dimensions 5.65 inch (144mm) wide, 6.50 inch (165mm) high, 2.80 inch (72mm) deep
Packaging Corrosion resistant zinc-plated steel with black enamel paint
Environment 5% RH to 95%, non-condensing, – 40°F (– 40°C) to 158°F (70°C)
Power: 5210 Controller Board: 11 - 30VDC, 12mW at 12V during Sleep
510mW at 12V during normal operation. 32MHz, LEDs off, no expansion, LAN and USB disabled
320mW at 12V during reduced power mode operation. 12MHz, LEDs off, no expansion,
LAN and USB disabled
1.2W at 12V during normal operation. 32MHz, LEDs off, no expansion, LAN enabled and USB disabled
Add 25 to 100mW when enabling the LEDs
8.5W at 24V maximum, 5V supply fully loaded
Power: 5607 I/O Module: 11 - 30VDC, 10.3mA plus analog outputs
325mA (max.) at 5V required from 5210 controller board
Warranty 3 years on parts and labor
1 Available only with optional integrated wireless modules or with stand-alone wireless modules.
2 Not applicable in all countries.
SCADAPack 33O|334 Product Data Sheet

Model Code P334-1A00-AB00 represents a sample code for a SCADAPack334, 5607 I/O board
and Modbus protocol emulation
Model Select: Controller
P330 SCADAPack330 comes with 3 Counter Inputs
P334 SCADAPack334, with Model 5607 I/O board, comes with 8 AI, 16 DI, 10 DO and 3 Counter Inputs
Code Select: Communication Ports
1 6 Communication Ports: 2 RS232/RS485 (RJ45), 1 RS232 (RJ45), 2 USB (A & B Type), 1 Ethernet (RJ45)
Code Select: Gas Flow Run-Time Option
A None
G 2 Run Gas Flow
F 4 Run Gas Flow
Code Select: Protocol Option
0 Modbus protocol emulation
1 Modbus and DF1 protocol emulation
2 Modbus and DNP 3.0 (Level 2) protocol emulation
3 Modbus, DF1 and DNP 3.0 (Level 2) protocol emulation
Code Select: Programming Environment
0 TelePACE Ladder Logic and C Language firmware loaded - IEC enabled (Programming Tools sold separately)
1 IEC 61131-3 and C Language firmware loaded - TelePACE enabled (Programming Tools sold separately)
Code Select: Analog Inputs
A P330: None – P334: 8 selectable as 0-20, 4-20mA, 0-5V or 0-10V
Code Select: Digital Inputs/Outputs
A P330 - None
B P334 - 16 DI (12/24V) and 10 dry contact relays
C P334 - 16 DI (48V) and 10 dry contact relays
D P334 - 16 DI (120V) and 10 dry contact relays
E P334 - 16 DI (240V) and 10 dry contact relays
F P334 - 16 DI (12/24V) and 10 DC solid state relays, ATEX and IECEx certification
G P334 - 16 DI (48V) and 10 solid state relays
H P334 - 16 DI (120V) and 10 solid state relays
I P334 - 16 DI (240V) and 10 solid state relays
Code Select: Analog Outputs
0 None
1 P334 only - 2 channel analog output option, 0 - 20mA
Code Select: Integrated Communication Interfaces
0 None
FreeWave & MDS Radios
1 900Mhz FreeWave Spread Spectrum Radio *Consult CMI for availability in your market area
2 2.4GHz FreeWave Spread Spectrum Radio *Consult CMI for availability in your market area
A 900MHz MDS Spread Spectrum Radio *Consult CMI for availability in your market area
Integrated SCADAWave Radio
B 900MHz SCADAWave Spread Spectrum Radio with encryption, 902-928MHz (FCC / IC)
C 900MHz SCADAWave Spread Spectrum Radio with encryption, 915-928MHz (AUS)
D 900MHz SCADAWave Spread Spectrum Radio, 915-928MHz (BRAZIL)
E 900MHz SCADAWave Spread Spectrum Radio, 921-928MHz (NZ)

Control
Microsystems
is becoming

CONTROL
MICROSYSTEMS w w w. c o n t r o l m i c r o s y s t e m s . com
Within Nor th America: (888) 267-2232 n Outside Nor th America: (613) 591-1943 n Ottawa n Calgar y n Denver n Houston n Melbourne n Leiden
Control Microsystems reserves the right to change product specifications without notice. Printed in Canada n V011 n M01011-60