8/25/2021 Calculating Cable Fault Ratings

Calculating Cable Fault Ratings 

By Steven McFadyen on January 6th, 2014 

When selecting a cable, the performance of the cable under fault conditions is an important consideration. It is important that
calculations be carried out to ensure that any cable is able to withstand the effects of any potential fault or short circuit.  This
note looks at how to do this.

The primary concern with cables under a fault condition is the heat generated, and any potential negative effect this may have
on the cable insulation. 

Calculation of fault rating is based on the principle that the protective device will isolate the fault in a time limit such that the
permitted temperature rise within the cable will not be exceeded.

Contents  [hide]
1. The adiabatic equation
2. Derivation  - Adiabatic Equation and k
1. Obtaining Values of k
3. Non-adiabatic effects
4. Other Cable Fault Issues
5. References

The adiabatic equation

When calculating the fault ratings of a cable, it is generally assumed that the duration so short enough that no heat is
dissipated by the cable to the surrounding.  Adopting this approach simplifies the calculation and errs on the safe side.

The normally used equation is the so-called  adiabatic equation.  For a given fault of I, which lasts for time t, the minimum
required cable cross sectional area is given by:

−−−
√ I 2t
A=
k
A=I2tk

A - the nominal cross section area, mm2

I - the fault current in, A

t -  duration of fault current, s

k - a factor dependant on cable type (see below)

Alternatively, given the cable cross section and fault current, the maximum time allowable for the protective device can be
found from:

https://myelectrical.com/notes/entryid/242/calculating-cable-fault-ratings 1/6
8/25/2021 Calculating Cable Fault Ratings

k 2 A2
t=
I2
t=k2A2I2

The factor k is dependant on the cable insulation, allowable temperature rise under fault conditions, conductor resistivity and
heat capacity.  Typical values of k are:

Value of k
Temperature Conductor Material
Initial °C] Final [°C] Copper Aluminium Steel
Thermoplastic 70°C (PVC)  70 160/140 115/103 76/78 42/37
 

Thermoplastic 90°C (PVC) 90 160/140 100/86 66/57 36/31

Thermosetting, 90°C (XLPE, EDR) 90 250 143 94 52

Thermosetting, 60°C (rubber) 60 200 141 93 51

Thermosetting, 85°C (rubber) 85 220 134 89 48

Thermosetting, 185°C (silicone rubber) 180 350 132 87 47

*where two values; lower value applied to conductor CSA > 300 mm2 

* these values are suitable for durations up to 5 seconds, source: BS 7671, IEC 60364-5-54

Tip: for a better understanding of cable insulation and how it is categorised, refer to our  Cable Insulation
Properties note .

Example

Consider a maximum fault current of 13.6 kA and the protective device trips in 2.6 s.  The minimum safe cable cross sectional
area of a copper thermosetting 90°C cable (k=143) is:

 
−−−−−−−−−−
√ 136002 × 2.6
S= = 154mm 2
143
S=136002×2.6143=154mm2

Any selected cable larger than this will withstand the fault.

Derivation  - Adiabatic Equation and k

https://myelectrical.com/notes/entryid/242/calculating-cable-fault-ratings 2/6
8/25/2021 Calculating Cable Fault Ratings

The term adiabatic applies to a process where there is no heat transfer.  For cable faults, we are assuming that all the heat
generated during the fault is contained within the cable (and not transmitted away).  Obviously this is not fully true, but it is on
the safe side.

From physics, the heat Q, required to rise a material ΔT is given by:

Q = cmΔT
Q=cmΔT

Q - heat added, J

c - specific heat constant of material, J.g-1.K-1

m - mass of the material, g

ΔT - temperature rise, K

The energy into the cable during a fault is given by:

Q = I 2 Rt
Q=I2Rt

R - the resistance of the cable, Ω

From the physical cable properties we can calculate m and R as:

m = ρ cAl
m=ρcAl

ρr l
R=
A
   and     R=ρrlA

ρc - material density in g.mm-3

ρr - resistivity of the conductor, Ω.mm

l - length of the cable, mm

Combining and substituting we have:

https://myelectrical.com/notes/entryid/242/calculating-cable-fault-ratings 3/6
8/25/2021 Calculating Cable Fault Ratings

I 2 Rt = cmΔT
I2Rt=cmΔT

ρr l
I 2t = cρ cAlΔT
A
I2tρrlA=cρcAlΔT

and rearranging for A gives:

 
−−−
√ I 2t
S=
k
S=I2tk

 
−−−−−−
cρ cΔT
k=√
ρr
   by letting    k=cρcΔTρr

Note: ΔT is the maximum allowable temperature rise for the cable:

ΔT = θf − θi
ΔT=θf−θi

θf - final (maximum) cable insulation temperature, °C

θi - initial (operating) cable insulation temperature, °C

Units:  are expressed in g (grams) and mm2, as opposed to kG and m.  This is widely adopted by cable specifiers. 
The equations can easily be redone in kG and m if required.

Obtaining Values of k

The constant k can be calculated from the above equation. 

A more common approach for is to use the tabulated values for k, for example, from BS 7671[1].

IEC 60364-5-54[2] also allows a more direct calculation of k, using:

https://myelectrical.com/notes/entryid/242/calculating-cable-fault-ratings 4/6
8/25/2021 Calculating Cable Fault Ratings

−−−−−−−−−−−−−−−−−−−−
Q c (β + 20) β + θf
k=√ ln ( )
ρ 20 β + θi
k=Qc(β+20)ρ20ln(β+θfβ+θi)

Qc - volumetric heat capacity of conductor at 20°C, J.K-1.mm-3

β - reciprocal of temperature coefficient of resistivity at 0°C, °C

ρ20 - resistivity of conductor as 20°C, Ω.mm

θi - initial conductor temperature, °C

θf - final conductor temperature, °C

    β [°C]    Qc [J.K-1.mm-3]  ρ20 [Ω.mm]  

Copper 234.5 3.45 x 10-3  17.241 x 10-6

Aluminium 228 2.5 x 10-3 28.267 x 10-6

Steel 202 3.8 x 10-3 138 x 10-6

Substituting the above values and rearranging the IEC equation slightly, gives:

−−−−−−−−−−−−−−−−
θf − θi
k = 226√ ln (1 + )
234.5 + θi
k=226ln(1+θf−θi234.5+θi)

- copper conductors

−−−−−−−−−−−−−−−
θf − θi
k = 148√ ln (1 + )
228 + θi
k=148ln(1+θf−θi228+θi)

- aluminium conductors

 
−−−−−−−−−−−−−−−
θf − θi
k = 78√ ln (1 + )
202 + θi
k=78ln(1+θf−θi202+θi)

- steel

Non-adiabatic effects

https://myelectrical.com/notes/entryid/242/calculating-cable-fault-ratings 5/6
8/25/2021 Calculating Cable Fault Ratings
As mentioned, the adiabatic equation assumes no heat is dissipated from the cable during a fault.  While putting the
calculation on the safe side, in some situations, particularly for longer fault duration there is the potential to be able to get
away with a smaller cross section.  In these instances, it is possible to do a more accurate calculation.

Considering non-adiabatic effects is more complex.  Unless there is some driver, using the adiabatic equations is just easier. 
Software is available to consider non adiabatic effects, however, there is a cost, time and complexity associated with this.

The IEC also publish a standard which deals with non-adiabatic equations:

IEC 60949 "Calculation of thermally permissible short-circuit current, taking into account non-adiabatic heating
effects".
 

The method adopted by IEC 60949 is to use the adiabatic equation and apply a factor to cater for the non-adiabatic effects:

I = εI AD
I=εIAD

I - permissible short circuit current, A (or kA)

IAD - adiabatic calculated permissible short circuit current, A (or kA)

ε - factor to allow for heat dissipation from cable

The bulk of the IEC 60949 standard is concerned with the calculation of ε.

Other Cable Fault Issues

In addition to the direct heating effect of fault currents, other considerations include:

electro-mechanical stress and fault levels large enough to cause cable failure
performance of joint and terminations under fault conditions
 

While in most cases the none heating effects are not serious, there may be situations where these could pose a risk to the
cable or equipment/personnel in the vicinity.

References
[1]. BS 7671 - Requirements for Electrical Installations. 17th ed. United Kingdom: IEE; 2008.
[2] IEC 60364-5-54 Low-voltage electrical installations - Part 5-54: Selection and erection of electrical equipment -
Earthing arrangements and protective conductors. 3rd ed. IEC; 2011.

https://myelectrical.com/notes/entryid/242/calculating-cable-fault-ratings 6/6