All manuals and user guides at all-guides.

com

JMA-9133-SA
JMA-9132-SA
JMA-9123-7XA/9XA
JMA-9122-6XA/9XA/6XAH
JMA-9110-6XA/6XAH

JMA-7133-SA

m
JMA-7132-SA
JMA-7123-7XA/9XA

.co
JMA-7122-6XA/9XA/6XAH
JMA-7110-6XA/6XAH
MARINE RADAR
EQUIPMENT
es
SIMPLIFIED MANUAL
1 INTRODUCTION ............................................................................................... 1
uid

1.1 READ ME ................................................................................................. 1

2 BASIC OPERATION ......................................................................................... 2
2.1 POWER ON AND START THE SYSTEM................................................. 2
2.2 END THE OPERATION AND POWER OFF............................................. 3
2.3 ADJUST MONITOR BRILLIANCE [BRILL]............................................. 3
2.4 CHANGE OBSERVATION RANGE [RANGE + / - ] ................................. 4
2.5 ADJUST GAIN [GAIN] ............................................................................. 4
2.6 SUPPRESS SEA CLUTTER [SEA] ......................................................... 4
2.7 SUPPRESS RAIN / SNOW CLUTTER [RAIN] ........................................ 6
-g

2.8 USING ELECTRONIC BEARING LINE (EBL1 / EBL2)........................... 7

2.9 USING VARIABLE RANGE MARKER (VRM1 / VRM2) .......................... 9
2.10 SWITCH TRANSMITTER PULSE LENGTH [GAIN] .............................. 10
2.11 SWITCH AZIMUTH DISPLAY MODE (AZI MODE) ................................ 10
2.12 SWITCH TRUE / RELATIVE MOTION DISPLAY MODE (TM / RM) .......11
2.13 DISPLAY RADAR TRAILS (TRAILS) .................................................... 12
all

3 TARGET TRACKING OPERATION ................................................................ 13

3.1 ACQUIRING TARGET [ACQ MANUAL] ............................................... 13
3.2 DISPLAY TRACKED TARGET DATA [TGT DATA] ............................... 13
3.3 CANCELING TRACKED TARGETS [ACQ CNCL]................................ 14
4 AIS OPERATION............................................................................................. 15
4.1 SETTING AIS DISPLAY FUNCTION [AIS / TT] ..................................... 15
4.2 ACTIVATE AIS TARGETS (ACT AIS) .................................................... 15
4.3 DISPLAY ACTIVATED AIS TARGET DATA [TGT DATA] ...................... 16
4.4 DEACTIVATE AIS TARGETS (DEACT AIS) .......................................... 17
5 TARGET TRACKING / AIS COMMON OPERATION...................................... 18
5.1 SETTING VECTORS (VECTOR)............................................................ 18
5.2 SETTING COLLISION DECISION CRITERIA (CPA / TCPA LIMIT) ...... 19
6 OTHER CONTENTS ....................................................................................... 20
6.1 RESET ALARM BUZZER [ALARM ACK] ............................................. 20
6.2 OPERATION ON NUMERIC VALUE INPUT MENU .............................. 20
All manuals and user guides at all-guides.com
 All manuals and user guides at all-guides.com

1 INTRODUCTION
1.1 Read Me
About this manual
See the INSTRUCTION MANUAL for details.
Maintain this SIMPLIFIED MANUAL so that operators can refer to it at anytime.

About radar equipment

Use the radar only as a navigation aid. The final navigation decision must always be made by the
operator him/herself. Making the final navigation decision based only on the radar display may cause
accidents such as collisions or running aground.

About sea clutter suppression

When using the sea clutter suppression function, never set the suppression level too high canceling out
all image noises from the sea surface at close range.
Detection of not only echoes from waves but also targets such as other ships or dangerous objects will
become inhibited.
When using the sea clutter suppression function function, make sure to choose the most appropriate
image noise suppression level.

About rain/snow clutter suppression

When using the rain/snow clutter suppression function function, never set the suppression level too
high canceling out all image noises from the rain or snow at close range.
Detection of not only echoes from the rain or snow but also targets such as other ships or dangerous
objects will become inhibited.
When using the rain/snow clutter suppression function function, make sure to choose the most
appropriate image noise suppression level.

About target tracking (TT) function

Use target tracking function only as a navigation aid. The final navigation decision must always be
made by the operator him/herself. Making the final navigation decision based only on tracking target
information may cause accidents.
Tracked target information such as vector, target numerical data, and alarms may contain some errors.
Also, targets that are not detected by the radar cannot be acquired or tracked.
Making the final navigation decision based only on the radar display may cause accidents such as
collisions or running aground.

1
 All manuals and user guides at all-guides.com

2 BASIC OPERATION
2.1 Power ON and Start the System

Procedures

1 Check that the ship’s mains are turned on.

2 Press the [POWER] key.

The system is turned on, and the preheating time is displayed.

Preheat is indicated upper left of the display.

3 Wait until the preheating time is over.

When the preheating time is over, the preheating time screen disappears, and Preheat upper left of
the display changes to Standby .

4 Press the [TX / STBY] key.

The radar will start transmission and the antenna will start rotating.
Standby upper left of the display changes to Transmit .

2
 All manuals and user guides at all-guides.com

2.2 End the Operation and Power Off

Exit

1 Press the [TX / STBY] key.

The radar will stop transmission and the antenna will stop rotating.
Transmit upper left of the display changes to Standby .

2 Press the [POWER] key.

The system will be turned off.

2.3 Adjust Monitor Brilliance [BRILL]

Procedures

1 Obtain the best-to-see display with optimum brilliance by turning the

[BRILL] dial at the lower right of the LCD monitor unit.

In consideration of the ambient brightness, adjust LCD monitor brilliance that is high enough to easily
observe the radar display but does not glare.

3
 All manuals and user guides at all-guides.com

2.4 Change Observation Range [RANGE + / - ]

Procedures

1 When increasing the observation range, press the [RANGE+] key.

m
Increasing the observation range will enable a wider range to be observed.

2 When decreasing the observation range, press the [RANGE-] key.

.co
Decreasing the observation range will enable a narrower range to be observed.
es
2.5 Adjust Gain [GAIN]

Procedures

1 Turning the [GAIN] dial.

uid

By increasing receiving gain, the range to observe radar video is widened.

-g

2.6 Suppress Sea Clutter [SEA]

all

Using the manual sea clutter suppression mode

Procedures

1 Turning the [SEA] dial.

The sea clutter suppression function suppresses sea clutter returns by decreasing the receiving gain on
a short range.

4
 All manuals and user guides at all-guides.com

Using the automatic sea clutter suppression mode

Procedures

1 Press the [SEA] dial.

The automatic sea clutter suppression mode is selected, and AUTO is displayed in sea clutter
suppression (Sea) mode switching.

2 Make adjustments by turning the [SEA] dial.

Even when the automatic sea clutter suppression mode is selected, turning the [SEA] dial can make
fine adjustments manually.

Cancellation

1 Press the [SEA] dial.

The automatic sea clutter suppression mode is cancelled, and MAN is displayed in the sea clutter
suppression (Sea) mode field.

5
 All manuals and user guides at all-guides.com

2.7 Suppress Rain / Snow Clutter [RAIN]

Using the manual rain / snow clutter suppression mode

Procedures

1 Turning the [RAIN] dial.

The rain / snow clutter suppression function suppress rain / snow clutter returns by decreasing the
receiving gain.
Since the rain / snow clutter suppression function also has the effect of suppressing sea clutter, the
suppression efficiency improves when the [RAIN] dial is used with the [SEA] dial.

Using the automatic rain / snow clutter suppression mode

Procedures

1 Press the [RAIN] dial.

The automatic rain / snow clutter suppression mode is selected, and AUTO is displayed in the sea
clutter suppression (Sea) mode switching and the rain / snow clutter suppression (Rain) mode
switching.

2 Make adjustments by turning the [RAIN] dial and the [SEA] dial.

Even when the automatic rain / snow clutter suppression mode is selected, turning the [RAIN] dial and
the [SEA] dial can make fine adjustments manually.

6
 All manuals and user guides at all-guides.com

Cancellation

1 Press the [RAIN] dial.

The automatic rain / snow clutter suppression mode is cancelled, and AUTO is changed to
MAN in the sea clutter suppression (Sea) mode field and the rain / snow clutter suppression (Rain)
mode field.

2.8 Using Electronic Bearing Line (EBL1 / EBL2)

[I] Operating EBL (EBL)

Procedures

1 Press the [EBL1] or [EBL2] key.

The EBL adjustment will be highlighted, and the selected EBL becomes operable.

2 Turn the [EBL] dial.

To turn the [EBL] dial to the right, turn the EBL dial clockwise, to turn the [EBL] dial to the left, turn
the EBL dial counterclockwise.

7
 All manuals and user guides at all-guides.com

Cancellation

1 Press the [EBL1] or [EBL2] key again.

The selected EBL display will disappear.

[II] Moving the Starting Point of EBL

The system provides three types of EBL starting points. Select one of them in accordance with
purpose.
:The EBL starting point is defined as the own ship's position.
C :The EBL starting point is moved and fixed on the radar display.
D :The EBL starting point is moved and fixed at the latitude and longitude.

To move the starting point of EBL

Procedures

1 Make EBL1 or EBL2 operable.

2 Press the [EBL] dial to set C or D for the EBL1 / EBL2 starting
point mode switching.

The selected EBL starting point mode is switched as shown below each time the dial is pressed.

3 Put the cursor on the EBL starting point is to be moved, and left-click.

The selected EBL starting point will be determined.

8
 All manuals and user guides at all-guides.com

To return the EBL starting point to own ship's position

Procedures

1 Make EBL1 or EBL2 operable.

2 Press the [EBL] dial to set for the EBL1 / EBL2 starting point mode
switching.

m
The selected EBL starting point will be set as the own ship's position.

.co
es
2.9 Using Variable Range Marker (VRM1 / VRM2)

To operate VRM

Procedures
uid

1 Press the [VRM1] or [VRM2] key.

-g

The VRM adjustment will be highlighted, and the selected VRM becomes operable.
all

2 Turn the [VRM] dial.

To turn the [VRM] dial to the right, the VRM control wide, to turn the [VRM] dial to the left, the
VRM control narrow.

9
 All manuals and user guides at all-guides.com

Cancellation

1 Press the [VRM1] or [VRM2] key again.

The selected VRM display will disappear.

2.10 Switch Transmitter Pulse Length [GAIN]

Procedures

1 Press the [GAIN] dial.

The selected pulse length will be displayed in the pulse length indication.

2.11 Switch Azimuth Display Mode (AZI Mode)

Procedures

1 Put the cursor on the azimuth display mode switching, and left-click.

The azimuth display modes are switched.

10
 All manuals and user guides at all-guides.com

2.12 Switch True / Relative Motion Display Mode (TM / RM)

Switching Motion Display Mode

Procedures

1 Put the cursor on the motion mode true TM / relative RM

switching, and left-click.

The motion display mode are switched.

Resetting Own Ship to its Initial Position in True Motion (TM) Mode

Procedures

1 Hold down the motion mode true / relative switching TM for

2 seconds.

Own ship will be reset to its initial position as established when the relative motion mode is changed to
the true motion mode. The ship starts moving from that position.

11
 All manuals and user guides at all-guides.com

2.13 Display Radar Trails (TRAILS)

Changing the length of the trail

Procedures

1 Put the cursor on the radar trails display time switching, and left-click.

Values of the length of the radar trail are switched.

Erasing Trails Data

Procedures

1 Hold down the radar trails display time switching for 5 seconds.

All the saved trails data will be erased. The system starts plotting trails in initial state.
If radar trails display time switching button is pushed for 2 seconds, a RADAR Trails Setting menu
will be displayed. Furthermore, data will be erased if it continues pressing.

Changing Motion Mode of Trails (Trails mode)

Procedures

1 Put the cursor on radar trails display true T / relative R switching,

and left-click.

The trails motion modes are switched.

If true motion (TM) mode is selected in azimuth display mode, only the true motion trails mode is
available.

12
 All manuals and user guides at all-guides.com

3 TARGET TRACKING OPERATION

3.1 Acquiring Target [ACQ MANUAL]

Procedures

1 Put the cursor on the target to be acquired, and press the

[ACQ MANUAL] key.

The target will be acquired and the initial acquisition symbol will be displayed. The vector will be
displayed within one minute.

3.2 Display Tracked Target Data [TGT DATA]

Procedures

1 Put the cursor on the tracked target for which numeric data is to be
displayed, and press the [TGT DATA] key.

The data of the selected target will be displayed.

13
 All manuals and user guides at all-guides.com

3.3 Canceling Tracked Targets [ACQ CNCL]

Canceling targets one by one [ACQ CNCL]

Procedures

1 Put the cursor on the tracked target to the desired for canceling target,
and press the [ACQ CNCL] key.

m
The vectors and symbols of the tracked targets will disappear, and only the radar video remain.

.co
es
Canceling all targets collectively [ACQ CNCL]

Procedures

1 Press the [ACQ CNCL] key for 5 seconds.

uid

The vectors and symbols of all the targets will disappear, and only the radar video remain.
-g
all

14
 All manuals and user guides at all-guides.com

4 AIS OPERATION
4.1 Setting AIS Display Function [AIS / TT]

Procedures

1 Press the [AIS / TT] key.

The received AIS information will be shown on the radar display.

4.2 Activate AIS Targets (ACT AIS)

Procedures

1 Put the cursor on the sleeping AIS target to be activated, and right-click.

The setting items for cursor modes will be displayed.

15
 All manuals and user guides at all-guides.com

2 Left-click 2. ACT AIS .

The selected AIS target will be activated.

4.3 Display Activated AIS Target Data [TGT DATA]

Procedures

1 Put the cursor on the AIS target of which data is to be displayed, and
press the [TGT DATA] key.

The data of the selected AIS target will be displayed.

16
 All manuals and user guides at all-guides.com

4.4 Deactivate AIS Targets (DEACT AIS)

Procedures

1 Put the cursor on the activated AIS target to be deactivated, and

right-click.

The setting items for cursor modes will be displayed.

2 Left-click 5. DEACT AIS .

The selected AIS target will be deactivated.

17
 All manuals and user guides at all-guides.com

5 TARGET TRACKING / AIS COMMON

OPERATION
5.1 Setting Vectors (Vector)

Setting vector mode [T / R / VECT]

Procedures

1 Press the [T / R / VECT] key.

The current vector mode T (true vector) or R (relative vector) will be displayed in the target
vector display true / relative switching.

Setting vector time on the display (Vector Time)

Procedures

1 Put the cursor on the target vector time setting, and left-click.

The Vector Time value input screen will appear.

2 Enter the value to be set as vector time.

For how to input numeric data on the numeric value input menu, see Section 6.2.

18
 All manuals and user guides at all-guides.com

5.2 Setting Collision Decision Criteria (CPA / TCPA Limit)

Input of CPA Limit

Procedures

1 Put the cursor on the CPA limit setting, and left-click.

m
The CPA Limit value input screen will appear.

.co
2 Enter the value to be set as a CPA limit.
es
For how to input numeric data on the numeric value input menu, see Section 6.2.

Input of TCPA Limit

uid

Procedures

1 Put the cursor on the TCPA limit setting, and left-click.

-g
all

The TCPA Limit value input screen will appear.

2 Enter the value to be set as a TCPA limit.

For how to input numeric data on the numeric value input menu, see Section 6.2.

19
 All manuals and user guides at all-guides.com

6 OTHER CONTENTS
6.1 Reset Alarm Buzzer [ALARM ACK]

Procedures

1 Press the [ALARM ACK] key.

The alarm will stop buzzing.

6.2 Operation on Numeric Value Input menu

Entered value

Numeric button

Enter button

Procedures

1 Put the cursor on the numeric button to the desired value, and left-click.

2 Make sure that the entered value is correct, put the cursor on the enter
button ENT , and left-click.

The set value is reflected to the operating state.

20
All manuals and user guides at all-guides.com
 All manuals and user guides at all-guides.com

For further information,contact:

Not use the asbestos

URL http://www.jrc.co.jp
Marine Service Department
Telephone : +81-3-3492-1305
Facsimile : +81-3-3779-1420
e-mail : [email protected]
AMSTERDAM Branch
Telephone : +31-20-658-0750
Facsimile : +31-20-658-0755
e-mail : [email protected]
SEATTLE Branch
Telephone : +1-206-654-5644
Facsimile : +1-206-654-7030
e-mail : [email protected]
CODE No.7ZPRD0711 01ETM ISO 9001, ISO 14001 Certified
JUN. 2008 Edition 1 JRC Printed in Japan