Analysis of Interactions Among The Barriers of Reverse Logistics

Download as pdf or txt
Download as pdf or txt
You are on page 1of 19

Technological Forecasting & Social Change 72 (2005) 1011 – 1029

Analysis of interactions among the barriers of reverse logistics


V. Ravi, Ravi Shankar*
Department of Management Studies, Indian Institute of Technology Delhi, Hauz Khas, New Delhi 110 016, India
Received 1 April 2004; received in revised form 30 June 2004; accepted 1 July 2004

Abstract

The aim of this article is to analyze the interaction among the major barriers, which hinder or prevent the
application of reverse logistics in automobile industries. A key task of top management is to diagnose those
barriers of reverse logistics that could be crucial to the survival of the organization in the future. Existing
models have focused on diagnosing these barriers independently. As a result, we lack a holistic view in
understanding the barriers that hinder reverse logistics. This paper utilizes the Interpretive Structural Modeling
(ISM) methodology to understand the mutual influences among the barriers so that those driving barriers, which
can aggravate few more barriers and those independent barriers, which are most influenced by driving barriers
are identified. By analyzing the barriers using this model, we may extract crucial barriers that hinder the reverse
logistics activities. It can be observed that there are some barriers, which have both high driving power and
dependency, thus needing more attention. An actual example of a small case automobile company provides
some managerial insights into the methodology. Finally, the implications for practice and future research are
discussed.
D 2004 Elsevier Inc. All rights reserved.

Keywords: Reverse logistics; Barriers; Interpretive Structural Modeling (ISM)

1. Introduction

Supply chains are undergoing radical transformations due to the mega-competition taking place on a
global scale. Technological changes are becoming a primary driver in the domain of businesses.

* Corresponding author. Tel.: +91 11 26596421 (O), 26564371 (R); fax: +91 11 26862620 (O).
E-mail addresses: r.s@rediffmail.com8 ravi1@dms.iitd.ernet.in (R. Shankar).

0040-1625/$ - see front matter D 2004 Elsevier Inc. All rights reserved.
doi:10.1016/j.techfore.2004.07.002
1012 V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029

Companies are finding that they must deal with a high level of uncertainty, which is not only technical
in nature. It is being observed by companies that there is an increase in the flow of returns of the
product due to product recalls, warranty returns, service returns, end-of-use returns, end-of-life returns,
and so on. Reverse logistics stands for all the operations related to the reuse of used products, excess
inventory of products and materials including collection, disassembly and processing of used products,
product parts, and/or materials [1]. Economic, environmental or legislative reasons have also increased
the relevance of reverse logistics in the present-day scenario. Many industries have adopted reverse
logistics practices. Fleischmann et al. [2] review the case studies on logistics network design in
different industries. Some industries have also engaged third parties for providing reverse logistics
services. Krumwiede and Sheu [3] have dealt with a model for reverse logistics entry by third-party
providers. Martino and Lenz [4] identify the major barriers that hinder the application of policy-
relevant information, derived from analytical techniques, to practical decisions by actual decision
makers. Ettlie [5] report a study of barriers, facilitators, and incentives to innovation among suppliers
to the U.S. automotive industry. Veloso and Fixson [6] provide a new framework to analyze the
decision of the automakers of whether to develop a new component in-house or to subcontract it to a
supplier.
The concept of reverse logistics has received growing attention in the last decades, due to a number of
factors. Competition and marketing motives, direct economic motives and concerns with the
environment are some of the important of them. With the legislative measures tightening up, there
are not many options left with the companies, but to go for reverse logistics practices. The
implementation of these may be a risky endeavor for the top management as it involves financial and
operational aspects, which determine the performance of the company in the long run. A critical analysis
of the barriers hindering reverse logistics and their interaction with the various aspects in integrative
planning can be a valuable source of information to decision makers.
The Indian automobile industry is flooded with automobile manufacturers like General Motors,
Hyundai, Fiat, Honda, etc., setting up manufacturing bases in India. These industries invest a great deal
of resources in terms of capital, labor, energy, and raw materials in delivering goods and services to
customer. When the products complete their life cycle, an important question that remains to be
answered is what would be the ultimate fate of these products. Thus, the reverse distribution of the
process of bringing products from the retailer level through the distributor back to the supplier or
manufacturer is an important factor, which needs consideration. The reverse logistics assumes
tremendous importance in this context. Reverse logistics is extensively used in the automobile industry
[7] and many other industries are following suit. However, the deployment of reverse logistics is not free
from barriers. Some of these barriers are lack of systems, management inattention, financial resources,
personnel resources, lesser importance of reverse logistics relative to other issues, and company policies
[8]. The above-mentioned barriers not only affect the operations of reverse logistics but also influence
one another. Thus, it is very essential to understand the mutual relationship among the barriers. The
identification of the barriers that are at the root of some more barriers (called driving barriers) and those
which are most influenced by the others (called driven barriers) would be helpful for the top
management implementing the reverse logistics programs. This can be a guide for taking appropriate
action to tackle barriers in reverse logistics.
Interpretive Structural Modeling (ISM) can be used for identifying and summarizing relationships
among specific variables, which define a problem or an issue [9,10]. It provides us a means by which
order can be imposed on the complexity of such variables [11,12]. Therefore, in this paper, the barriers of
V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029 1013

the reverse logistics in automobile industries have been analyzed using the ISM methodology, which
shows the interrelationships of the barriers and their levels. These barriers are also categorized depending
on their driving power and dependence.
After review of literature on reverse logistics and the opinion of experts, both from automobile
industry and the academia, 11 important barriers of reverse logistics have been identified. The literature
review, together with the experts’ opinion, was used in developing the relationship matrix, which is later
used in the development of an ISM model.
The main objectives of this paper are:

(i) to identify and rank the barriers of reverse logistics in automobile supply chains,
(ii) to find out the interaction among identified barriers using ISM, and
(iii) to discuss the managerial implications of this research.

This paper is further organized as follows. The next section discusses the identification of barriers of
reverse logistics in Indian automobile industries, which is followed by the discussion of ISM
methodology. MICMAC analysis of developed ISM model is carried out subsequently. The model is
subsequently applied to a decision that is being faced by a small automobile company. Finally, the results
of this research are presented, which is followed by discussion and conclusion.

2. Barriers of reverse logistics

Despite the fact that practices related to reverse logistics have helped the cause of environment
protection, practicing the much-needed approaches is not free from barriers. In this paper, 11 variables
for barriers to the reverse logistics have been selected from the literature primarily from Ref. [8] and also
from discussions with experts in the automobile industry, keeping the Indian automotive industry in
focus (Table 1). These barriers are explained as follows.

2.1. Lack of information and technological systems

A very serious problem faced by the firms in the implementation of reverse logistics is the dearth of
good information systems [8]. An efficient information and technological system is very necessary for
supporting the reverse logistics during various stages of the product life cycle. During the product
development phase, the important variables to be considered are the material content and the product
structure. The type of the materials and the technology used for manufacturing determine the extent of
the product recovery that is possible after the end-of-use/end-of-life of the product. Excellent
information and technological systems can be very useful for the product development programs
encompassing the design for the environment, recovery, reuse, and so on generally called as the Design
for X (DfX). Efficient information systems are needed for individually tracking and tracing the returns of
the product, linking with the previous sales. Relating the product return with a past sale can support
forecasting of product returns, thus helping in the inventory management [13]. It can be very useful for
the planning and control of the product recovery activities. Information support is necessary for
developing linkages to achieve efficient reverse logistics operations [14]. Landers et al. [15] describe a
concept of bvirtual warehousingQ where real-time information feeds expeditious algorithms to support
1014 V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029

Table 1
Structural Self-Interaction Matrix (SSIM)

decisions for tracking component’s order in the case of a closed-loop business telephones supply chain.
Maslennikova and Foley [16] describe the case of Xerox where bar code labels were used to track
packaging material with the aim of achieving resources preservation. Mok et al. [17] describe the use of
information and new technologies to improve processes in the reverse chain for the situation where
products and equipment need to be disassembled. Very few Indian firms have successfully automated the
information surrounding the returns process. There is a dearth of good reverse logistics information
management systems commercially available [8]. Thus, this is a very significant barrier affecting good
reverse logistics.

2.2. Problems with product quality

Another important barrier affecting reverse logistics is the condition of the quality of the end-of-use/
end-of-life returned products. The product quality is not uniform in reverse logistics compared to the
forward logistics where the product quality is uniform [18]. Thierry et al. [7] opine that the overall
quality targets for remanufactured/recycled products must be, at the least, equivalent to the virgin
products. Customers usually expect the same level of quality of product from the manufacturer
regardless of the nature of the returned product. Rudi et al. [19] describe the product recovery at the
Norwegian national insurance administration where the Technical Aid Centers (TACs) had the task of
distributing and servicing the wheelchairs, hearing aids, and speech synthesizers where depending upon
the product quality, the TACs reused some units, repaired others, and refurbished still others. When the
returned products arrive at the distribution center, a decision must be made for its disposition.
Gatekeeping, which is a process of screening of the defective and unwarranted returned products at the
V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029 1015

entry point into the reverse logistics, is a very critical factor in realizing the entire reverse flow
manageable and profitable. The returned product quality could be in any range; like that it could be
faulty, damaged, or simply unwanted by the customer. Thus, there could be variations in the pricing of
the products. The prices of the products in the forward channel could vary due to a lot of the factors like
the quantity of the products purchased. The quality of the returned products is inspected by gatekeeping
and a decision is then made to the disposition of the product. Thus, in the case of the returned product,
the pricing can be more difficult compared to the forward logistics.

2.3. Company policies

Restrictive company policies are an important barrier to the reverse logistics [8]. The lack of the
importance of the reverse logistics and the management inattention are related to the policies followed by
the companies. Companies want to create a brand image to the customers. They do not want to
compromise on the end-product quality by using the returned products. Thus, the policies developed by
companies of producing only virgin products also have a major effect of not handling the returned
products and to recover the hidden secondary value from the returns. Due to the advent of extended
producer responsibility [20], many companies have started to integrate the recovery options for the
products into their supply chain. There seems to be a paradigm shift by the companies to change their
rigid policies to incorporate the returns of the product to recover value economically that could give
them edge over their competitors.

2.4. Resistance to change to reverse logistics

A chief barrier seen in the implementation of the reverse logistics is the resistance to change, human
nature being a fundamental barrier. People avoid change when possible, and the reverse logistics require
a radical change in the mindset and practice. Resistance to change can also be caused especially in the
case for small business with limited purchasing power to influence contracts with suppliers [21]. The
company policies and organizational structures get in the way rather than facilitate change. The absence
of a clear reverse logistics vision further accelerates the problem. With increased competition in the
market and shrinked profit margin, companies are increasingly interested in savings with the recovery of
the used products. Most importantly, the adoption of the reverse logistics practices results in direct
benefits to the environment. The lack of awareness of the benefits of the reverse logistics both from
economic and environment angles could be a major factor for the resistance to change to reverse
logistics. Reverse logistics systems initially involve high economic investment. Financial constraints
could also lead to resistance to change to reverse logistics.

2.5. Lack of appropriate performance metrics

Lack of performance metrics is a major barrier to the reverse logistics programs. One of the barriers
for supply chain alignment is lack of appropriate performance metrics [22]. Performance metrics form
the basis of integrated work management systems. Simply stated, bWork not measured cannot be
managed.Q The performance measurement of any system is a key element in enabling the process of
performance management, performance improvement, performance documentation, etc. If the firms take
action linking their performance measurement system to their reverse logistics practices, they will be in a
1016 V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029

better position to succeed in their endeavor. Successful reverse logistics programs will effectively
coordinate all the processes, focus on recapturing value or proper disposal of products, create
environmental friendly products, and create performance measurement systems that provide data as to
whether the designed reverse logistics is performing up to the expectations.

2.6. Lack of training and education

A significant barrier to good reverse logistics is lack of personnel resources [8]. Lack of training and
education is a major challenge to commercial cycling [23]. Education and training are prime
requirements for achieving success in any organization. The need for training on reverse logistics
extends throughout the company and reaches up and downstream. New or revamped technology
necessitates change and the personnel should be given adequate training in the new technology and
processes that will be implemented. The training should be provided in critical business functions like
product development, customer account management, etc., so as which gives rise to new development
opportunities to improve integration of environmental issues.

2.7. Financial constraints

Financial constraints are a key barrier to good reverse logistics programs [8]. Cost considerations are a
prime challenge in commercial recycling [23]. Finance is essential to support the infrastructure and
manpower requirements of the reverse logistics. Companies require allocation of funds and other
resources for the implementation of reverse logistics. Efficient information and technological systems are
significant enabler for reverse logistics. Information and technological systems require more funds
because without these, the returns product tracking and tracing and product recovery by various process
like reuse, remanufacturing, recycling, etc. is not possible in the present environment. The training of
personnel related to the reverse logistics is also very important for efficiently managing and eventually
making the reverse logistics profitable. However, all these require financial support.

2.8. Lack of commitment by top management

Lack of commitment by top management is a chief barrier for successful reverse logistics [8].
Mintzberg [24] states that top management commitment is the dominant driver of corporate endeavors.
A major challenge seen in commercial recycling is the lack of commitment by top management [23].
Efficient leadership is needed to provide clear vision and value to reverse logistics programs. The top
management should demonstrate commitment to the reverse logistics activities on par with other
organizational goals by integrating all the members of the supply chain. They should provide
continuous support for reverse logistics in the strategic plans, action plans for successfully
implementing them.

2.9. Lack of awareness about reverse logistics

A chief barrier of reverse logistics seen in Indian automobile supply chain is lack of awareness
about the benefits of reverse logistics. Even if companies knew about it, giving relative unimportance
to reverse logistics was seen as the largest barrier to reverse logistics [8]. Firms are finding in a
V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029 1017

position irrespective of whatever industry they are, whether automobile, food processing, or paper
industry, there is an increasing case of product recalls. Today, many consumer products have a shorter
life cycle. While the customers have the benefits of greater product variety, it has resulted in an
increase in unsold products, rate of returns, packing materials, and also the waste [25]. This has given
rise to increase in the volume of product returns in the form of reverse logistics. Therefore, the
management of parts or product coming back into the supply chain network from its outbound side is
a matter of concern for many industries [26]. The reverse logistics can lead to economic benefits by
the recovery of the returned products for reuse, remanufacturing, recycling, or a combination of these
options for adding value to the product. The implementation of the reverse logistics leads to direct
benefits to the environment, too. Thus, the lack of the awareness of these benefits is a major barrier to
reverse logistics.

2.10. Lack of strategic planning

More than ever before, the economy and e-commerce are demanding that companies make reverse
logistics part of their strategic planning arsenal [27]. Reverse logistics can be used as a strategic
weapon in the present industrial environment [8]. Strategic planning is the identification of reverse
logistics goals and the specification of long-term plans for managing them. It involves the attempt on
the part of the manager on the course of action that has to be adopted for the realization of reverse
logistics. In the present scenario, due to the rapid changes in technology and also due to changes in the
behaviors of competitors, consumers, suppliers, etc., a sound strategic planning is necessitated for the
reverse logistics programs. For implementation of reverse logistics in any organization, the role of
strategic planning is very important to achieve the goals for the survival of the organization in the
global market.

2.11. Reluctance of the support of dealers, distributors, and retailers

Another important barrier to the reverse logistics is the reluctance of the support of the dealers,
distributors, and retailers towards the reverse logistics activities. A generous return policy leads to
improved risk sharing between sellers and consumers. The liberal returns policy can lead to the
consumers returning the product in any form to the retailers. The liberal returns policy occasionally turns
into bReturn abuseQ policies [8].

3. ISM methodology and model development

The methodology of ISM is an interactive learning process. In this a set of different and directly
related variables affecting the system under consideration is structured into a comprehensive systemic
model. The beauty of the ISM model is that it portrays the structure of a complex issue of the problem
under study, in a carefully designed pattern employing graphics as well as words. The methodology of
ISM can act as a tool for imposing order and direction on the complexity of relationships among
elements of a system [10,28]. Saxena et al. [29] applied the ISM methodology to the case of bEnergy
Conservation in Indian Cement IndustryQ and identified the key variables using direct as well as indirect
interrelationships amongst the variables. Sharma et al. [30] have employed ISM methodology to develop
1018 V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029

a hierarchy of actions required to achieve the future objective of waste management in India. Mandal and
Deshmukh [11] used the ISM methodology to analyze some of the important vendor selection criteria
and have shown the inter-relationships of criteria and their levels. These criteria have also been
categorized depending on their driver power and dependence. A number of barriers exist in the practice
of reverse logistics in automobile industry. An examination of the direct and indirect relationships
between the barriers of the reverse logistics can give a clearer picture of the situation than considering
individual factors alone in isolation. The ISM can be judiciously employed for getting better insights into
the system under consideration.
The ISM methodology is interpretive from the fact that as the judgment of the group decides whether
and how the variables are related. It is structural too, as on the basis of relationship; an overall structure
is extracted from the complex set of variables. It is a modeling technique in which the specific
relationships of the variables and the overall structure of the system under consideration are portrayed in
a digraph model. ISM is primarily intended as a group learning process, but it can also be used
individually. The various steps involved in the ISM methodology are as follows:

Step 1: Variables affecting the system under consideration are listed, which can be Objectives,
Actions, and Individuals etc.
Step 2: From the variables identified in step 1, a contextual relationship is established among
variables with respect to which pairs of variables would be examined.
Step 3: A Structural Self-Interaction Matrix (SSIM) is developed for variables, which indicates
pairwise relationships among variables of the system under consideration.
Step 4: Reachability matrix is developed from the SSIM and the matrix is checked for transitivity.
The transitivity of the contextual relation is a basic assumption made in ISM. It states that if a
variable A is related to B and B is related to C, then A is necessarily related to C.
Step 5: The reachability matrix obtained in Step 4 is partitioned into different levels.
Step 6: Based on the relationships given above in the reachability matrix, a directed graph is drawn
and the transitive links are removed.
Step 7: The resultant digraph is converted into an ISM, by replacing variable nodes with statements.
Step 8: The ISM model developed in Step 7 is reviewed to check for conceptual inconsistency and
necessary modifications are made.

These steps of ISM modeling are illustrated in Fig. 1.

3.1. Structural Self-Interaction Matrix

ISM methodology suggests the use of the expert opinions based on various management techniques
such as brain storming, nominal technique, etc., in developing the contextual relationship among the
variables. Thus, in this research for identifying the contextual relationship among the barriers of the
reverse logistics, two experts, one each from the automobile industry and the academia, were consulted
for the same. These experts from the industry and academia were well conversant with reverse logistics
practices in the automobile industry having an experience of over 10 years. For analyzing the barriers of
the reverse logistics variables, a contextual relationship of bleads toQ type is chosen. This means that one
variable leads to another variable. Based on this, contextual relationship between the variables is
developed.
V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029 1019

Fig. 1. Flow diagram for preparing ISM.

Keeping in mind the contextual relationship for each variable, the existence of a relation between any
two barriers (i and j) and the associated direction of the relation is questioned. Four symbols are used to
denote the direction of relationship between the barriers (i and j):

V: Barrier i will help alleviate Barrier j;


A: Barrier j will be alleviated by Barrier i;
1020 V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029

X: Barriers i and j will help achieve each other; and


O: Barriers i and j are unrelated.

The following would explain the use of the symbols V, A, X, and O in SSIM (Table 1).

(i) Barrier 8 helps alleviate Barrier 10. This means that as efforts are made to plug the gap in the top
management commitment towards the reverse logistics practices, effectiveness of strategic
planning improves. Thus, the relationship between Barriers 8 and 10 is denoted by dVT in the
SSIM (Table 1).
(ii) Barrier 8 can be alleviated by Barrier 9, i.e. removal of Barrier 9, namely, black of awareness about
reverse logisticsQ would help alleviate Barrier 8 (i.e. black of commitment by top managementQ).
Awareness about the various benefits of reverse logistics would promote the top management
commitment for implementing reverse logistics programs. Thus, the relationship between these
barriers is denoted by dAT in the SSIM (Table 1).
(iii) Barriers 4 and 6 help achieve each other. Barrier 4, namely, bresistance to change for activities
related to reverse logistics,Q and Barrier 6, namely, black of training related to reverse logistics,Q
help achieve each other. Thus, the relationship between these barriers is denoted by dXT in the
SSIM (Table 1).
(iv) No relationship exists between lack of appropriate performance metrics (Barrier 5) and financial
constraints (Barrier 7) and hence the relationship between these barriers is denoted by dOT in the
SSIM (Table 1).

Table 2
Initial reachability matrix
V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029 1021

Based on similar contextual relationships, the SSIM is developed for all the 11 barriers identified for
the reverse logistics (Table 1).

3.2. Reachability matrix

The SSIM is transformed into a binary matrix, called the initial reachability matrix by substituting V,
A, X, O by 1 and 0 as per the case. The rules for the substitution of 1’s and 0’s are the following:

1. If the (i, j) entry in the SSIM is V, then the (i, j) entry in the reachability matrix becomes 1 and the
( j, i) entry becomes 0.
2. If the (i, j) entry in the SSIM is A, then the (i, j) entry in the reachability matrix becomes 0 and the
( j, i) entry becomes 1.
3. If the (i, j) entry in the SSIM is X, then the (i, j) entry in the reachability matrix becomes 1 and the
( j, i) entry also becomes 1.
4. If the (i, j) entry in the SSIM is O, then the (i, j) entry in the reachability matrix becomes 0 and the
( j, i) entry also becomes 0.

Following these rules, initial reachability matrix for the barriers is shown in Table 2.

Table 3
Final reachability matrix
1022 V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029

Table 4
Iteration 1
Barrier Reachability set Antecedent set Intersection set Level
1 1, 4, 5, 6, 11 1, 2, 3, 4, 6, 7, 8, 9, 10 1, 4, 6
2 1, 2, 3, 4, 5, 6, 11 2, 8, 9, 10 2
3 1, 3, 4, 5, 6, 11 2, 3, 7, 8, 9, 10 3
4 1, 4, 5, 6, 11 1, 2, 3, 4, 6, 7, 8, 9, 10 1, 4, 6
5 5 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 5 I
6 1, 4, 5, 6, 11 1, 2, 3, 4, 6, 7, 8, 9, 10 1, 4, 6
7 1, 3, 4, 5, 6, 7, 11 7, 8, 9, 10 7
8 1, 2, 3, 4, 5, 6, 7, 8, 10, 11 8, 9 8
9 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 9 9
10 1, 2, 3, 4, 5, 6, 7, 10, 11 8, 9, 10 10
11 5, 11 1, 2, 3, 4, 6, 7, 8, 9, 10, 11 11

The final reachability matrix is obtained by incorporating the transitivities as enumerated in Step 4 of
the ISM methodology. This is shown in Table 3. In this table, the driving power and dependence of each
barrier are also shown. The driving power of a particular barrier is the total number of barriers (including
itself) which it may help achieve. The dependence is the total number of barriers which may help
achieving it. These driving power and dependencies will be used in the MICMAC analysis, where the
barriers will be classified into four groups of autonomous, dependent, linkage, and independent (driver)
barriers.

3.3. Level partitions

The reachability and antecedent set [9] for each barrier is found out from final reachability matrix.
The reachability set for a particular variable consists of the variable itself and the other variables,
which it may help achieve. The antecedent set consists of the variable itself and the other variables,
which may help in achieving them. Subsequently, the intersection of these sets is derived for all
variables. The variable for which the reachability and the intersection sets are the same is given the
top-level variable in the ISM hierarchy, which would not help achieve any other variable above their
own level. After the identification of the top-level element, it is discarded from the other remaining

Table 5
Iteration 2
Barrier Reachability set Antecedent set Intersection set Level
1 1, 4, 6, 11 1, 2, 3, 4, 6, 7, 8, 9, 10 1, 4, 6
2 1, 2, 3, 4, 6, 11 2, 8, 9, 10 2
3 1, 3, 4, 6, 11 2, 3, 7, 8, 9, 10 3
4 1, 4, 6, 11 1, 2, 3, 4, 6, 7, 8, 9, 10 1, 4, 6
6 1, 4, 6, 11 1, 2, 3, 4, 6, 7, 8, 9, 10 1, 4, 6, 11
7 1, 3, 4, 6, 7, 11 7, 8, 9, 10 7
8 1, 2, 3, 4, 6, 7, 8, 10, 11 8, 9 8
9 1, 2, 3, 4, 6, 7, 8, 9, 10, 11 9 9
10 1, 2, 3, 4, 6, 7, 10, 11 8, 9, 10 10
11 11 1, 2, 3, 4, 6, 7, 8, 9, 10, 11 11 II
V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029 1023

Table 6
Iteration 3
Barrier Reachability set Antecedent set Intersection set Level
1 1, 4, 6 1, 2, 3, 4, 6, 7, 8, 9, 10 1, 4, 6 III
2 1, 2, 3, 4, 6 2, 8, 9, 10 2
3 1, 3, 4, 6 2, 3, 7, 8, 9, 10 3
4 1, 4, 6 1, 2, 3, 4, 6, 7, 8, 9, 10 1, 4, 6 III
6 1, 4, 6 1, 2, 3, 4, 6, 7, 8, 9, 10 1, 4, 6 III
7 1, 3, 4, 6, 7 7, 8, 9, 10 7
8 1, 2, 3, 4, 6, 7, 8, 10 8, 9 8
9 1, 2, 3, 4, 6, 7, 8, 9, 10 9 9
10 1, 2, 3, 4, 6, 7, 10 8, 9, 10 10

variables. From Table 4, it is seen that lack of performance metrics (Barrier 5) is found at Level I.
Thus, it would be positioned at the top of the ISM model. This iteration is continued till the levels of
each variable are found out. The identified levels aids in building the digraph and the final model of
ISM. The barriers, along with their reachability set, antecedent set, intersection set and the levels, are
shown in Tables 4–10.

3.4. Formation of ISM-based model

From the final reachability matrix, the structural model is generated. If the relationship exists between
the Barriers j and i, an arrow pointing from i to j shows this. This resulting graph is called a digraph.
Removing the transitivities as described in the ISM methodology, the digraph is finally converted into
the ISM model as shown in Fig. 3.
It is observed from Fig. 3 that lack of awareness of reverse logistics (Barrier 9) is a very significant
barrier for the reverse logistics in the Indian automobile industries as it comes as the base of the ISM
hierarchy. Lack of appropriate performance metrics (Barrier 5) is the reverse logistics barrier on which
the effectiveness of the reverse logistics depends. This barrier has appeared at the top of the hierarchy.
The lack of awareness about reverse logistics (Barrier 9) leads to the lack of commitment by the top
management towards the reverse logistics activities (Barrier 8), which results in lack of strategic
planning pertaining to reverse logistics activities (Barrier 10). A good strategic planning should be in
place before allocating finance related to reverse logistics (Barrier 7) as otherwise it may lead to
problems with product quality (Barrier 2) which would be counter to the objectives of green supply

Table 7
Iteration 4
Barrier Reachability set Antecedent set Intersection set Level
2 2, 3 2, 8, 9, 10 2
3 3 2, 3, 7, 8, 9, 10 3 IV
7 3, 7 7, 8, 9, 10 7
8 2, 3, 7, 8, 10 8, 9 8
9 2, 3, 7, 8, 9, 10 9 9
10 2, 3, 7, 10 8, 9, 10 10
1024 V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029

Table 8
Iteration 5
Barrier Reachability set Antecedent set Intersection set Level
2 2 2, 8, 9, 10 2 V
7 7 7, 8, 9, 10 7 V
8 2, 7, 8, 10 8, 9 8
9 2, 7, 8, 9, 10 9 9
10 2, 7, 10 8, 9, 10 10

chain. Financial constraints (Barrier 7) force restrictive company policies as the reverse logistics systems
involve high investment, which small firms cannot afford. Problems with product quality (Barrier 2)
would lead to rigid company policies (Barrier 3) as the companies, in order to keep up their brand image
in the market, would be producing new products for attaining customer satisfaction. This could result
into bresistance to changeQ in the practices of reverse logistics (Barrier 4). Thus, awareness about reverse
logistics must be created at the grass roots level and should be disseminated to all the partners of the
supply chain such that effective reverse logistics practices can be implemented.
Lack of information and technological systems (Barrier 1) and resistance to change to reverse logistics
(Barrier 4) are interrelated. Good information and technological systems are very essential for successful
reverse logistics programs. Lack of these would cause a resistance to change by people, as the required
technologies are not available. The resistance to change related to reverse logistics would further result
in lack of procurement of information and technological systems for reverse logistics. bResistance to
changeQ during implementation of reverse logistics activities (Barrier 4) would have a negative impact on
the outcomes of training and education on these issues (Barrier 6). This would also result in reluctance to
gain support from the dealers, distributors, and retailers (Barrier 11). Without this support, it would be
difficult to evolve and implement performance metrics related to reverse logistics (Barrier 5).

4. MICMAC analysis

The objective of the MICMAC analysis is to analyze the driver power and the dependence power of
the variables [11]. The variables are classified into four clusters (Fig. 2). The first cluster consists of the
dautonomous barriersT that have weak driver power and weak dependence. These barriers are relatively
disconnected from the system, with which they have only few links, which may be strong. Second
cluster consists of the dependent barriers that have weak driver power but strong dependence. Third
cluster has the linkage barriers that have strong driving power and also strong dependence. These
barriers are unstable in the fact that any action on these barriers will have an effect on others and also a

Table 9
Iteration 6
Barrier Reachability set Antecedent set Intersection set Level
8 8, 10 8, 9 8
9 8, 9, 10 9 9
10 10 8, 9, 10 10 VI
V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029 1025

Table 10
Iteration 7
Barrier Reachability set Antecedent set Intersection set Level
8 8 8, 9 8 VII
9 8, 9 9 9 VIII

feedback on themselves. Fourth cluster includes the independent barriers having strong driving power
but weak dependence. It is observed that a variable with a very strong driving power called the key
variables, falls into the category of independent or linkage barriers. The driving power and the
dependence of each of these barriers are shown in Table 3. In this table, an entry of d1T along the columns
and rows indicates the dependence and driving power, respectively. Subsequently, the driver power–
dependence diagram is constructed which is shown in Fig. 2. As an illustration, it is observed from Table
3 that Barrier 7 is having a driver power of 7 and a dependence of 4. Therefore, in this figure, it is
positioned at a place corresponding to a driver power of 7 and a dependency of 4.

5. A small company example

The ISM model presented here has been evaluated in an actual automobile company that was
interested in implementing reverse logistics. Due to limited budget, the company wanted a systematic

Fig. 2. Driving power and dependence diagram.


1026 V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029

Fig. 3. ISM-based model for the barriers of reverse logistics.

way of analyzing the interaction of barriers that hinder implementation of reverse logistics. This case
experience allows us to see the benefits of the model in a practical setting.

6. Discussion and conclusion

The barriers hindering the reverse logistics programs pose considerable challenges both for managers
and policymakers in industries. Some of the major barriers have been highlighted here and put into an
ISM model, to analyze the interaction between the barriers. These barriers need to be overcome for the
success in reverse logistics programs. The driver–dependence diagram gives some valuable insights
about the relative importance and the interdependencies among the barriers. This can give better insights
V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029 1027

to the top management so that they can proactively deal with these barriers. Some of the observations
from the ISM model, which give important managerial implications, are discussed below.
Lack of the awareness of reverse logistics practices is a very significant barrier. From the ISM model,
it is observed that strategic management issues like lack of awareness of reverse logistics and lack of
commitment by top management are at the bottom level of the hierarchy implying higher driving power.
Therefore, top management should focus on developing strategies to create awareness about the use of
reverse logistics so that the benefits of it can be reaped.
There are no autonomous barriers seen in the driver–dependence diagram (Fig. 2). The absence of
these barriers brings light to the fact that all the considered barriers influence the reverse logistics in the
automobile supply chain. It is also observed that lack of performance metrics, reluctance of support by
supply chain partners, lack of information and technological systems, resistance to change during
deployment of reverse logistics practices, lack of training, and unconcerned company policies are weak
drivers but strongly dependent on other barriers such as lack of awareness, lack of commitment, lack of
strategic planning, quality problems, and financial constraints. The management should place a high
priority in tackling the barriers, which have a high driving power and thus possessing the capability to
influence other barriers, which are shown at the upper level of the ISM (Fig. 3). No barrier is found
under the linkage element category possessing a strong driving power along with strong dependence.
Therefore, among all the 11 selected barriers of reverse logistics, no barrier is unstable.
It is also observed from the ISM model that five barriers, namely, lack of awareness of reverse logistics,
lack of commitment by the top management, problems with product quality, lack of strategic planning,
and financial constraints have strong driver power and therefore, these are less dependent on the other
barriers. Thus, it can be inferred that these are strong drivers and may be treated as the root cause of
remaining barriers. To manage these barriers, a comprehensive strategic plan for reverse logistics should
to be initiated to achieve success. The decision maker, in this small company example, could potentially
target the barriers hindering reverse logistics so that the desired objectives could be met.
Despite the fact that the ISM model developed in this research is for the barriers prominently seen in
the automobile companies, some generalization of results are still possible. The corporate environment is
fast moving towards an environment-conscious supply chain and reverse logistics is an obvious
candidate for being managed better. Thus, the identification of the barriers affecting the implementation
of reverse logistics in any supply chain assumes great importance. This can aid the top management in
deciding the priority so that it can proactively take steps in combating these barriers. The barriers
identified in the ISM model are quite generic and, with marginal adjustments, can be used for many other
supply chains.
Thus, the ISM-based model proposed in this paper for identification of barriers of reverse logistics can
provide the decision maker a more realistic representation of the problem in the course of conducting
reverse logistics. A major contribution of this research lies in the development of linkages among various
barriers of a reverse logistics through a single systemic framework. The utility of the proposed ISM
methodology in imposing order and direction on the complexity of relationships among elements of a
system assumes tremendous value to the decision makers.
At the end, we examine the scope of further research. In this research, using the ISM methodology, a
relationship model among the barriers of reverse logistics in Indian automobile industries has been
developed. But this model has not been statistically validated. Structural equation modeling (SEM), also
referred to as linear structural relationship approach, has the capability of testing the validity of such
hypothetical models. Thus, this approach can be applied in the future research to test the validity of this
1028 V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029

model. It is worth mentioning here that while comparing ISM and SEM, although SEM has the
capability of statistically testing an already developed theoretical model, it cannot develop an initial
model for testing. ISM, on the other hand, has the capability to develop an initial model through
managerial techniques such as brain storming, nominal group techniques, etc. In this sense, ISM is a
supportive analytic tool for the discussed situation.

References

[1] A.I. Kokkinaki, R. Dekker, M.B.M. de Koster, C. Pappis, W. Verbeke, From e-trash to e-treasure: how value can be created
by the new e-business models for reverse logistics. Available at https://ep.eur.nl/retrieve/1010/feweco20010219160545.pdf
(2001).
[2] M. Fleischmann, H.R. Krikke, R. Dekker, S.D.P. Flapper, A characterization of logistics networks for product recovery,
Omega 28 (2000) 653 – 666.
[3] D.W. Krumwiede, C. Sheu, A model for reverse logistics entry by third-party providers, Omega 30 (2002) 325 – 333.
[4] J.P. Martino, R.C. Lenz, Barriers to use of policy-relevant information by decision makers, Technol. Forecast. Soc. Change
10 (4) (1977) 381 – 390.
[5] J.E. Ettlie, Stimulating the flow of innovations to the U.S. automotive industry, Technol. Forecast. Soc. Change 19 (1)
(1981) 33 – 55.
[6] F. Veloso, S. Fixson, Make–buy decisions in the auto industry: new perspectives on the role of the supplier as an innovator,
Technol. Forecast. Soc. Change 67 (2001) 239 – 257.
[7] M. Thierry, M. Salomon, V.J. Nunen, L.N.V. Wassenhove, Strategic issues in product recovery management, Calif.
Manage. Rev. 37 (1995) 114 – 135.
[8] D.S. Rogers, R.S. Tibben-Lembke, Going Backwards: Reverse Logistics Trends and Practices, Reverse Logistics
Executive Council, Pittsburgh, PA, 1998.
[9] J.W. Warfield, Developing interconnected matrices in structural modeling, IEEE Transcr. Syst. Men Cybern. 4 (1) (1974)
51 – 81.
[10] A.P. Sage, Interpretive Structural Modeling: Methodology for Large-Scale Systems, McGraw-Hill, New York, NY, 1977,
pp. 91 – 164.
[11] A. Mandal, S.G. Deshmukh, Vendor selection using interpretive structural modeling (ISM), Int. J. Oper. Prod. Manage. 14
(6) (1994) 52 – 59.
[12] S. Jharkharia, R. Shankar, IT-enablement of supply chains: understanding the barriers, J. Enterprise Inf. Manag.
(2005) (in press).
[13] M.P. de Brito, S.D.P. Flapper, R. Dekker, Reverse logistics: a review of case studies. Econometric Institute Report EI
2002-21. Available at http://www.eur.nl/WebDOC/doc/econometrie/feweco20020605160859.pdf (accessed 2002).
[14] P.J. Daugherty, M.B. Myers, R.G. Richey, Information support for reverse logistics: the influence of relationship
commitment, J. Bus. Logist. 23 (1) (2002) 85 – 106.
[15] T.L. Landers, M.H. Cole, B. Walker, R.W. Kirk, The virtual warehousing concept, Transp. Res. Part E Logist. Trans. Rev.
36 (2) (2000) 115 – 125.
[16] I. Maslennikova, D. Foley, Xerox’s approach to sustainability, Interfaces 30 (3) (2000) 226 – 233.
[17] H.S. Mok, H.J. Kim, K.S. Moon, Disassemblability of mechanical parts in automobile for recycling, Comput. Ind. Eng. 33
(3–4) (1997) 621 – 624.
[18] R.S. Tibben-Lembke, D.S. Rogers, Differences between forward and reverse logistics in a retail environment, Supply
Chain Manag. Int. J. 7 (5) (2002) 271 – 282.
[19] N. Rudi, D.F. Pyke, P.O. Sporsheim, Product recovery at the Norwegian National Insurance Administration, Interfaces 30
(3) (2000) 166 – 179.
[20] T. Lindhqvist, Extended producer responsibility in cleaner production; Policy principle to promote environmental
improvements of product systems. Unpublished PhD thesis, Lund University, Sweden, 2000.
[21] FoE Sydney, Reusable transport packaging. Available at http://www.sydney.foe.org.au/SustainableConsumption/
epr_pamphlets/reusable_pack.html (accessed 2001).
V. Ravi, R. Shankar / Technological Forecasting & Social Change 72 (2005) 1011–1029 1029

[22] S.E. Fawcett, G.M. Magnan, Achieving world-class supply chain alignment: Benefits, barriers, and bridges. Available at
http://www.capsresearch.org/publications/pdfs-public/fawcett2001es.pdf (accessed 2001).
[23] WSRA, Business Recycling Roundtable Tukwila Washington minutes. Available at http://www.wsra.net/pdf/
Minutes%201-12-01.doc (accessed January 12, 2001).
[24] H. Mintzberg, The Nature of Managerial Work, Harper & Row, New York, 1973.
[25] R.I. Van Hoek, From reverse logistics to green supply chains, Supply Chain Manag. Int. J. 4 (3) (1999) 129 – 134.
[26] R. Guintini, T. Andel, Advance in reverse logistics: Part 1, Transp. Distrib. 36 (2) (1995) 73 – 77.
[27] WERC, Reverse logistics: A Weapon in strategic planning. Available at http://www.werc.org/email/archive/email/
default.asp?EMAIL_ID=75 (accessed 2002).
[28] M.D. Singh, R. Shankar, R. Narain, A. Agarwal, An interpretive structural modeling of knowledge management in
engineering industries, J. Adv. Manage. Res. 1 (1) (2003) 28 – 40.
[29] J.P. Saxena, Sushil, P. Vrat, Scenario building: a critical study of energy conservation in the Indian cement industry,
Technol. Forecast. Soc. Change 41 (2) (1992) 121 – 146.
[30] H.D. Sharma, A.D. Gupta, Sushil, The objectives of waste management in India: a futures inquiry, Technol. Forecast. Soc.
Change 48 (1995) 285 – 309.

Dr. Ravi Shankar is currently Assistant Professor of Operations and Information Technology
management. He is Group Chair of Sectoral Management at the Department of Management Studies
at Indian Institute of Technology Delhi, India. He has nearly 23 years of teaching experience. His areas of
interest are Supply Chain Management, Knowledge Management, Flexible Manufacturing Systems,
TQM, etc. His publications have appeared in various journals including the European Journal of
Operational Research, International Journal of Production Research, Computers and Industrial
Engineering, International Journal of Production Economics, Computers and Operations Research,
International Journal of Supply Chain Management, etc. He is the executive editor of Journal of
Advances in Management Research.

V. Ravi is a currently a research scholar at Department of Management Studies, Indian Institute of


Technology Delhi, India. His areas of interest include reverse logistics and supply chain management.

You might also like