EDWARDS Catalog  Intelligent Initiating Devices

LIFE SAFETY & INCIDENT MANAGEMENT

Intelligent
Multisensor Smoke
and Heat Detector
SIGA-PHD

S853

Overview Standard Features

The Signature Series SIGA-PHD detector brings advanced multi- Note: Some features described here may not be supported by
sensor technology to a practical design that increases efficiency, all control systems. Check your control panel’s Installation and
saves installation time, cuts costs, and extends life safety and Operation Guide for details.
property protection capabilities. Continuous self-diagnostics en-
• Next Generation Detection Technology
sures reliability over the long-haul, while environmental compensa-
tion helps reduce maintenance costs. • Integrates optical smoke with rate-of-rise heat sensing
The SIGA-PHD provides an optical smoke sensor and a rate-of- • Wide 0.53 to 3.94 %/ft. (1.7 to 12.35 %/m) smoke obscuration
rise heat sensor with a fixed temperature setting. Together these • Uses existing wiring
sensors efficiently detect smoldering fires, as well as fast flaming
fires. • Automatic device mapping

Like all Signature Series detectors, the SIGA-PHD gathers analog • Sensor Markings Provide Easy Testing Identification
information from its sensing elements and converts this data into • Up To 250 Total Signature Adresses Per Loop
digital signals. To make an alarm decision, the detector’s on-board
microprocessor measures and analyzes smoke and heat sensor • Two levels of environmental compensation
readings and compares this information to historical data. Digital • Two levels of dirty detector warning
filters remove signal patterns that are not typical of fires, thus virtu-
ally eliminating unwanted alarms. • Twenty pre-alarm settings
• Five sensitivity settings
• Non-volatile memory
• Electronic addressing
• Environmental compensation
• Automatic day/night sensitivity adjustment
• Bicolor (green/red) status LED
• Standard, relay, fault isolator, and audible mounting bases

Page 1 of 4 D ATA S H E E T E85001-0650

Not to be used for installation purposes. Issue 1
Application Automatic Device Mapping - The loop controller learns where
each device’s serial number address is installed relative to other
Smoke detection devices on the circuit. The mapping feature provides supervision
The SIGA-PHD detects extremely small particles of combustion of each device’s installed location to prevent a detector from being
and triggers an alarm at the first sign of smoke. Thanks to its high- reinstalled (after cleaning etc.) in a different location from where it
performance forward-scattering reflective response technology, was originally.
the photoelectric smoke sensor responds quickly and reliably to
a wide range of fire types, espe­cially slow burning fires fuelled by Fast Stable Communication - On-board intelligence means less
combustibles typically found in modern multi-use buildings. information needs to be sent between the detector and the loop
controller. Other than regular supervisory polling response, the
Heat detection detector only needs to communicate with the loop controller when
SIGA-PHD’s on-board rate-of-rise heat sensor provides a 15 °F it has something new to report.
(9 °C) per minute for the detection of fast-developing fires while
also providing a 135 °F (57.2 °C) fixed detection threshold. The
heat sensors monitor the temperature of the air and determines Accessories
whether an alarm should be initiated. Detector mounting bases have wiring terminals that are acces-
sible from the “room-side” after mounting the base to the electrical
box. The bases mount to North American 1-gang boxes and to
3½ inch or 4 inch octagon boxes, 1½ inches (38 mm) deep. They
Compatibility also mount to European BESA and 1-gang boxes with 60.3 mm
The SIGA-PHD detector is compatible only with the Signature fixing centers. The SIGA-SB4, SIGA-RB4, and SIGA-IB4 mount to
Loop Controller. North American 4 inch sq. electrical boxes in addition to the above
boxes. They include the SIGA-TS4 Trim Skirt, which is used to
cover the “mounting ears” on the base. Sounder bases mount to a
4 inch square boxes only.
Installation
Signature Series detectors mount
to North American 1-gang boxes,
3-1/2 inch or 4 inch octagon
boxes, and to 4 inch square elec- Self-locking tab
SIGA-AB4G/T/LF SIGA-SB SIGA-IB SIGA-RB SIGA-LED
trical boxes 1-1/2 inches (38 mm) Audible Base Standard Base Isolator Base Relay Base Remote LED
deep. They mount to European
BESA and 1-gang boxes with 60.3 Remote LED SIGA-LED - The remote LED connects to the
mm fixing centers. See mounting SIGA-SB or SIGA-SB4 Standard Base only. It features a North
LED Indicator
American size 1-gang plastic faceplate with a white finish and red
base installation and wiring for
alarm LED.
more information.
SIGA-TS4 Trim Skirt - Supplied with 4 inch bases, it can also
be ordered separately to use with the other bases to help hide
surface imperfections not covered by the smaller bases.
Testing & Maintenance Sounder Bases - Signature Series sounder bases are designed
Scheduled maintenance (regular or selected) for proper detector for use where localized or group alarm signaling is required.
operation should be planned to meet the requirements of the Au- • SIGA-AB4G bases provide sounder capability to Signature
thority Having Jurisdiction (AHJ). Refer to current NFPA 72, NFPA Series smoke and heat detectors. They are not for use with
720, and ULC CAN/ULC 536 standards. devices that include a CO sensor.
Smoke Sensor Sensitivity • SIGA-AB4GT bases provide sounder capability to Signature
The SIGA-PHD determines when its optical sensor is dirty or Series smoke and heat detectors, as well as Signature detec-
defective and can transmit sensitivity data to the loop controller. tors that include a CO Sensor when used with a SIGA-TCDR
A sensitivity report can also be printed to satisfy NFPA sensitivity Temporal Pattern Generator to separate CO (TC4) and Fire
measurements which must be conducted at the end of the first (TC3) tone patterns.
year and every two years thereafter. The availability of maintenance • SIGA-AB4G-LF bases provide 520 Hz low frequency
features depends on the fire alarm system used. sounder capability to Signature Series smoke and heat detec-
tors, as well as Signature detectors that include a CO Sensor
when used with a SIGA-TCDR Temporal Pattern Generator to
separate CO (TC4) and Fire (TC3) tone patterns. The SIGA-
Sensing and reporting technology AB4G-LF is suitable for applications requiring low frequency
The microprocessor in each detector provides additional benefits - audible tones.
Self-diagnostics and History Log, Automatic Device Mapping, and
Fast, Stable Communication.
Self-diagnostics and History Log - Each Signature Series
detector constantly runs self-checks to provide important mainte-
nance information. The results of the self-check are automatically
updated and permanently stored in the detector’s non-volatile
memory.

Page 2 of 4 D ATA S H E E T E85001-0650

Not to be used for installation purposes. Issue 1
Typical Wiring
The detector mounting bases accept #18 AWG (0.75mm2), #16 Audible Sounder Bases, Fire Mode
(1.0mm2), #14 AWG (1.5mm2), and #12 AWG (2.5mm²) wire sizes. AB4GT, AB4G, AB4G-LF sounder bases
Sizes #16 AWG (1.0mm2) and #18 AWG (0.75mm2) are preferred
for ease of installation.
SIGA-AB4GT, SIGA-AB4G-LF:
Standard Detector Base, SIGA-SB, SIGA-SB4 SIGA-AB4G,
Jumper cuts
Output Mode
SIGA-AB4G-LF: Default = Fire
This is the basic mounting base Remote LED
Volume Setting
Default = High
Cut/remove jumper for
Fire plus CO
for EDWARDS Signature Series Max resistance Cut/remove
detectors. The SIGA-LED Re- per wire
must not exceed
jumper for SIGA-AB4G:
low dB Tone Setting
mote LED is supported by this 10 Ohms Default = Temporal
Base. DATA- DATA- DATA+
SIG+ SIG- OUT IN IN/OUT Cut/remove jumper for
Term Description Steady
1 Not Used
2 DATA IN/OUT (+) SIGA-AB4GT:
3 Not Used Not Used
4 DATA IN (-)
4 Remote LED (-) DATA IN (-) DATA OUT (-)
5 Remote LED (+)
6 Not Used 24 Vdc in
7 DATA OUT (-) DATA IN (+) DATA OUT (+) - - 24 Vdc out
From power supply
From Signature Controller To Next Device + To next base or EOL relay
or previous base +
or Previous Device
-
Data out
Data in -
From Signature Controller to next Signature device
Isolator Detector Base, SIGA-IB, SIGA-IB4 or previous device + +

This base includes a built-in line fault isolator for use on Class A
circuits. A detector must be installed for it to operate. The isolator
base does not support the SIGA-LED Remote LED.
The isolator operates as follows: Warnings & Cautions
- a short on the line causes all iso- • This detector does not operate without electrical power. As
lators to open within 23 msec fires frequently cause power interruption, discuss further safe-
- at 10 msec intervals, guards with the local fire protection specialist.
beginning on one side
of the Class A • This detector does not sense fires in areas where smoke or
circuit nearest the loop heat cannot reach the detector. Smoke or heat from fires in
controller, the isolators walls, roofs, or on the opposite side of closed doors may not
close to provide the reach the detector.
next isolator down the
line with power Term Description • Photoelectric detectors have a wide range of sensing capabili-
1 Not Used ties, and are best suited for detecting slow, smoldering fires.
- when the isolator next 2 DATA IN/OUT (+)
3 DATA IN (-) The heat sensor in this device provides a source of supplemen-
to the short closes, it reopens within 10 4 Not Used tal information. The heat sensor by itself does not provide life
msec. 5 Not Used
6 DATA OUT (-) safety protection.
The process repeats beginning on the 7 Not Used
other side of the loop controller. • In Canada, install according to the CAN/ULC-S524 Standard
for the Installation of Fire Alarm Systems, the CSA C22.1 Cana-
dian Electrical Code, and the local authority having jurisdiction.
Relay Detector Base, SIGA-RB, SIGA-RB4 • Upon completion of the original installation and following any
This base includes a relay. Nor- modifications or additions to the system, perform a calibrated
mally Open or Normally Closed sensitivity test per NFPA code. Signature Series devices can
operation is selected during in- perform this test and the panel can generate a system sensitiv-
stallation. The dry contact is rated ity report.
for 1 amp (pilot duty) @ 30 Vdc.
The relay’s position is supervised
to avoid accidentally jarring it out
of position. The SIGA-RB can be
operated as a control relay if pro-
grammed to do so at the control
panel. The relay base does not
Term Description
support the SIGA-LED Remote 1 Normally Open
LED. CONTACT RATING 2 DATA IN/OUT (+)
1.0 Amp @ 30 VDC 3 Common
(Pilot Duty) 4 DATA IN (-)
5 Not Used
6 Normally-Closed
7 DATA OUT (-)

Page 3 of 4 D ATA S H E E T E85001-0650

Not to be used for installation purposes. Issue 1
 Dimensions

L I F E S A F E TY & I NCI DE NT M AN AGEM EN T

Contact us...
Email: [email protected]
Web: Edwards-fire.com

EDWARDS is a UTC brand.

1016 Corporate Park Drive
Mebane, NC 27302

© 2016 United Technologies Corporation.

All rights reserved.

Specifications
Operating voltage 15.20 to 19.95 VDC
Normal operating current 32 µA
Alarm current 32 µA
Vibration level 10 to 35 Hz, with an amplitude of 0.01 in.
Smoke Sensitivity Range UL/ULC: 0.53 to 3.94 %/ft. (1.7 to 12.35 %/m) obscuration
Rate-of-rise rating 15°F/min (8°C/min)
Fixed temperature rating 135°F (57.2°C). Actual alarm point 129 to 141°F (53.9 to 60.6°C).
Air velocity 0 to 4,000 ft./min (0 to 20.32 m/s)
Wall mounting 12 in. (305 mm) max. from ceiling
Spacing, heat detectors Max. 50 ft. (15.2 m) centers
Compatible bases See Ordering Information
Compatible detector testers Testifire 1000, Testifire 2000
Operating environment 32 to 100°F (0 to 38°C), 0 to 93% RH, noncondensing
Construction High Impact Engineering Polymer, White
Storage temperature -4 to 140°F (-20 to 60°C)
Environmental compensation Automatic
Agency Listings CAN/ULC-S529, CAN/ULC-S530, UL 268, UL 268A, UL 521

Ordering Information
Catalog Ship Wt.
Description
Number lbs (kg)
SIGA-PHD Intelligent Multisensor Smoke and Heat Detector 0.4 (0.16)

Compatible Bases
SIGA-SB Detector Mounting Base - Standard
SIGA-SB4 4-inch Detector Mounting Base c/w Trim Skirt
SIGA-RB Detector Mounting Base w/Relay
SIGA-RB4 4-inch Detector Mounting Base w/Relay, c/w Trim Skirt 0.2 (.09)
SIGA-IB Detector Mounting Base w/Fault Isolator
SIGA-IB4 4-inch Detector Mounting Base w/ Fault Isolator, c/w Trim Skirt
SIGA-LED Remote Alarm LED (not for EN54 applications)
SIGA-AB4G-LF Low Frequency Audible (Sounder) Base for CO and Fire Detectors 0.3 (0.15)
SIGA-AB4GT Audible (Sounder) Base for CO and Fire Detectors 0.3 (0.15)
SIGA-TS4 Trim Skirt (supplied with 4-inch bases) 0.1 (.04)
SIGA-DMP Detector Mounting Plate 3.0 (1.4)
SIGA-RTA Detector Removal Tool
SIGA-VA Detector Cleaning Tool
10-11-16

Page 4 of 4 D ATA S H E E T E85001-0650

Not to be used for installation purposes. Issue 1