0% found this document useful (0 votes)

284 views42 pages

Installing The Software: Cisco 4000 Series Isrs Software Configuration Guide Ol-29328-03

Uploaded by

Anonymous XM3KoTUTg

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

284 views42 pages

Installing The Software: Cisco 4000 Series Isrs Software Configuration Guide Ol-29328-03

Uploaded by

Anonymous XM3KoTUTg

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 42

Installing the Software

This chapter includes the following sections:

• Overview, page 1
• ROMMON Images, page 2
• Provisioning Files, page 2
• File Systems, page 2
• Autogenerated File Directories and Files, page 3
• Flash Storage, page 4
• Configuring the Configuration Register for Autoboot, page 4
• Licensing, page 5

Overview
Installing software on the router involves installing a consolidated package (bootable image). This consists
of a bundle of subpackages (modular software units), with each subpackage controlling a different set of
functions.
These are the two main methods to install the software:
• Managing and Configuring a Router to Run Using a Consolidated Package, on page 13—This method
allows for individual upgrade of subpackages and generally has reduced boot times compared to the
method below. Use this method if you want to individually upgrade a module's software.
• Managing and Configuring a Router to Run Using Individual Packages, on page 17—This a simple
method that is similar to a typical Cisco router image installation and management that is supported
across Cisco routers.

It is better to upgrade software in a planned period of maintenance when an interruption in service is acceptable.
The router needs to be rebooted for a software upgrade to take effect.

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 1
Installing the Software
ROMMON Images

ROMMON Images
A ROMMON image is a software package used by ROM Monitor (ROMMON) software on a router. The
software package is separate from the consolidated package normally used to boot the router. For more
information on ROMMON, see the "ROM Monitor Overview and Basic Procedures" section in the Hardware
Installation Guide for the Cisco 4000 Series Integrated Services Routers.
An independent ROMMON image (software package) may occasionally be released and the router can be
upgraded with the new ROMMON software. For detailed instructions, see the documentation that accompanies
the ROMMON image.

Note A new version of the ROMMON image is not necessarily released at the same time as a consolidated
package for a router.

Provisioning Files
This section provides background information about the files and processes used in Managing and Configuring
a Router to Run Using Individual Packages, on page 17.
The consolidated package on a router consists of a collection of subpackages and a provisioning file titled
packages.conf. To run the software, the usual method used is to boot the consolidated package, which is
copied into memory, expanded, mounted, and run within memory. The provisioning file's name can be renamed
but subpackage file's names cannot be renamed. The provisioning file and subpackage files must be kept in
the same directory. The provisioning file does not work properly if any individual subpackage file is contained
within a different directory.

Note An exception to this is that if a new or upgraded module firmware package is subsequently installed, it
need not be in the same directory as the provisioning file.

Configuring a router to boot, using the provisioning file packages.conf, is beneficial because no changes have
to be made to the boot statement after the Cisco IOS XE software is upgraded.
Alternatively, for an example of booting using subpackages, see Configuring the Router to Boot Using
Subpackages.

File Systems
The following table provides a list of file systems that can be seen on the Cisco 4000 series routers.

Table 1: Router File Systems

File System Description

bootflash: Boot flash memory file system.

Cisco 4000 Series ISRs Software Configuration Guide

2 OL-29328-03
Installing the Software
Autogenerated File Directories and Files

File System Description

flash: Alias to the boot flash memory file system above.

harddisk: Hard disk file system (if NIM-SSD, NIM-HDD, or internal mSATA flash device is
present in the router).
Note The internal mSATA flash device is supported only on Cisco ISR4300 Series
routers.
cns: Cisco Networking Services file directory.

nvram: Router NVRAM. You can copy the startup configuration to NVRAM or from
NVRAM.

obfl: File system for Onboard Failure Logging (OBFL) files.

system: System memory file system, which includes the running configuration.

tar: Archive file system.

tmpsys: Temporary system files file system.

usb0: The Universal Serial Bus (USB) flash drive file systems.
usb1: Note The USB flash drive file system is visible only if a USB drive is installed
in usb0: or usb1: ports.

Use the ? help option, or use the copy command in command reference guides, if you find a file system that
is not listed in the table above.

Autogenerated File Directories and Files

This section discusses the autogenerated files and directories that can be created, and how the files in these
directories can be managed.

Table 2: Autogenerated Files

File or Directory Description

crashinfo files Crashinfo files may appear in the bootflash: file system.
These files provide descriptive information of a crash and may be useful for
tuning or troubleshooting purposes. However, the files are not part of router
operations, and can be erased without impacting the functioning of the router.

core directory The storage area for .core files.

If this directory is erased, it will automatically regenerate itself at bootup.
The .core files in this directory can be erased without impacting any router
functionality, but the directory itself should not be erased.

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 3
Installing the Software
Flash Storage

File or Directory Description

lost+found directory This directory is created on bootup if a system check is performed. Its
appearance is completely normal and does not indicate any issues with the
router.

tracelogs directory The storage area for trace files.

Trace files are useful for troubleshooting. If the Cisco IOS process fails, for
instance, users or troubleshooting personnel can access trace files using
diagnostic mode to gather information related to the Cisco IOS failure.
Trace files, however, are not a part of router operations, and can be erased
without impacting the router's performance.

Important Notes About Autogenerated Directories

Important information about autogenerated directories include:
• Autogenerated files on the bootflash: directory should not be deleted, renamed, moved, or altered in any
way unless directed by Cisco customer support.

Note Altering autogenerating files on the bootflash: may have unpredictable consequences
for system performance.

• Crashinfo, core, and trace files can be deleted.

Flash Storage
Subpackages are installed to local media storage, such as flash. For flash storage, use the dir bootflash:
command to list the file names.

Note Flash storage is required for successful operation of a router.

Configuring the Configuration Register for Autoboot

The configuration register can be used to change router behavior. This includes controlling how the router
boots. Set the configuration register to 0x0 to boot into ROM, by using one of the following commands:
• In Cisco IOS configuration mode, use the config-reg 0x0 command.
• From the ROMMON prompt, use the confreg 0x0 command.

Cisco 4000 Series ISRs Software Configuration Guide

4 OL-29328-03
Installing the Software
Licensing

For more information about the configuration register, see Use of the Configuration Register on All Cisco
Routers and Configuring a Router to Boot the Consolidated Package via TFTP Using the boot Command:
Example, on page 14.

Note Setting the configuration register to 0x2102 will set the router to autoboot the Cisco IOS XE software.

Note The console baud rate is set to 9600 after changing the confreg to 0x2102 or 0x0. If you cannot establish
a console session after setting confreg, or garbage output appears, change the setting on your terminal
emulation software to 9600.

Licensing
• Cisco Software Licensing, on page 5
• Consolidated Packages, on page 5
• Technology Packages, on page 6
• Feature Licenses, on page 7
• Unlicensed Feature: Example, on page 12

Cisco Software Licensing

Cisco software licensing consists of processes and components to activate Cisco IOS software feature sets by
obtaining and validating Cisco software licenses.
You can enable licensed features and store license files in the bootflash of your router. Licenses pertain to
consolidated packages, technology packages, or individual features.
An evaluation license is automatically converted to a Right to Use model after 60 days and this license is valid
permanently. The conversion to a permanent license applies only to evaluation licenses. For other features
supported on your router, you must purchase a permanent license.
See the "Configuring the Cisco IOS Software Activation Feature" chapter of the Software Activation
Configuration Guide, Cisco IOS XE Release 3S.

Consolidated Packages
One of the following two consolidated packages (images) is preinstalled on the router:
• universalk9—Contains the ipbasek9 base package and the securityk9, uck9, and appxk9 technology
packages.
• universalk9_npe—Contains the ipbasek9 base package and the securityk9_npe, uck9, and appxk9
technology packages. This image has limited crypto functionality.

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 5
Installing the Software
Technology Packages

Note The term npe stands for No Payload Encryption.

Note The terms super package and image also refer to a consolidated package.

To obtain software images for the router, go to http://software.cisco.com/download/navigator.html.

An image-based license is used to help bring up all the subsystems that correspond to a license. This license
is enforced only at boot time.
Apart from the universalk9 and universalk9_npe images, a Boot ROMMON image is available. For more
information, see ROMMON Images, on page 2.
For more information about identifying digitally signed Cisco software and how to show the digital signature
information of an image file, see the "Digitally Signed Cisco Software" section in the Loading and Managing
System Images Configuration Guide, Cisco IOS XE Release 3S.
The following examples show how to obtain software authenticity information and internal details of a package:
• Displaying Digitally Signed Cisco Software Signature Information
• Obtaining the Description of a Module or Consolidated Package

Many features within the consolidated package are contained in the ipbasek9 base package. The license key
for the ipbasek9 package is activated by default.

Technology Packages
Technology packages contain software features within a consolidated package. To use different sets of features,
enable the licenses of selected technology packages. You can enable the licenses for any combination of
technology packages.
Each technology package has an evaluation license that converts to a Right to Use (RTU) license after 60
days and is then valid permanently.
The following is a list of technology packages:
• securityk9, on page 6
• uck9, on page 7
• appxk9, on page 7

securityk9
The securityk9 technology package includes all crypto features, including IPsec, SSL/SSH, Firewall, and
Secure VPN.
The securityk9_npe package (npe = No Payload Encryption) includes all the features in the securityk9
technology package without the payload-encryption functionality. This is to fulfill export restriction
requirements. The securityk9_npe package is available only in the universalk9_npe image. The difference

Cisco 4000 Series ISRs Software Configuration Guide

6 OL-29328-03
Installing the Software
Feature Licenses

in features between the securityk9 package and the securityk9_npe package is therefore the set of
payload-encryption-enabling features such as IPsec and Secure VPN.

uck9
The uck9 technology package includes the following Cisco Unified Communications features:
• CUBE
• CME-SRST
• SBC

appxk9
The appxk9 technology package contains Application Experience features, which are similar to the features
in the DATA package of the Cisco Integrated Services Routers Generation 2 routers. For more information,
see: http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/
software-activation-on-integrated-services-routers-isr/white_paper_c11_556985.html#wp9000791.
There are many features in the appxk9 package, including MPLS, PfR, L2/L3 VPN, Broadband, and AVC.

Feature Licenses
To use each of the following features, enable a corresponding feature license, as explained in the following
sections:
• HSECK9, on page 7
• Performance, on page 8
• CME-SRST, on page 10

HSECK9
The HSECK9 license is required for a feature to have full crypto functionality. Without the HSECK9 license,
only 225 secure tunnels and 85 Mbps of crypto bandwidth would be available. The HSECK9 license allows
features in the securityk9 technology package to use the maximum number of secure tunnels and crypto
bandwidth. To enable the HSECK9 license, purchase the FL-44-HSEC-K9 license from Cisco.com and
install it using the license install license-files command. For further information on obtaining and installing
feature licenses, see Configuring the Cisco IOS Software Activation Feature.

Note The HSECK9 feature does not have an evaluation license that converts to an RTU license after 60 days;
a feature license must be obtained.

To enable the license for the HSECK9 feature, the securityk9 technology package is also required. For more
information about the securityk9 technology package, see securityk9, on page 6.

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 7
Installing the Software
Feature Licenses

Performance
The performance feature, which allows for increased throughput, is enabled by the performance license. This
feature is part of the ipbasek9 technology package. To enable the feature, order the performance license (part
number FL-44-PERF-K9). The license is displayed as the throughput license.
You can upgrade the throughput of the ESP from 2.5 Gbps to 5 Gbps by activating the right-to-use license
and then reloading the router. For more information on the right-to-use license activation, see Configuring
Cisco Right-To-Use License Configuration Guide. If you want to determine the current throughput level
of the ESP, run the show platform hardware throughput level command. The following example shows the
output of this command before the performance upgrade license is applied:
To configure the throughput level, perform the following steps and to upgrade the throughput level use the
platform hardware throughput level { 2500000 | 5000000} command.

1 In the user EXEC configuration mode, enter the enable command.

2 Enter configure terminal command to enter the global configuration mode.
3 To upgrade the throughput level, enter the platform hardware throughput level{2500000|5000000}
command.
4 To exit global configuration mode, enter exit.
5 To save the configuration, enter the copy running-config startup-config command.
6 To reload the router enter reload. A reload is required to activate the throughput level.

show platform hardware throughput level

The current throughput level is 2500000 kb/s
To configure the throughput level, perform the following steps and to upgrade the throughput level use the
platform hardware throughput level { 2500000 | 5000000} command.

1 In the user EXEC configuration mode, enter the enable command.

The following example shows how to upgrade the throughput level:

Router>enable
Router#configure terminal
Router(config)#platform hardware throughput level 5000000
% The config will take effect on next reboot
Router(config)#exit
Router#copy running-config startup-config
Router#reload

Cisco 4000 Series ISRs Software Configuration Guide

8 OL-29328-03
Installing the Software
Feature Licenses

Boost Performance License

The following two use-cases describe the processes of the boost performance licenses activation and deactivation
from the device.
Enable the boost performance license:
• Boot the device in Smart License mode. The boost performance command is not visible without registering
in the Smart Portal.
• After successfully registering to the Smart Portal, check the availability of the boost performance licenses
in the smart account.
• Use the platform hardware throughput level boost command to enable the feature. If a valid license is
still available in the smart account, the Boost Performance feature is enabled after the device is reloaded.
• To check for the platform hardware throughput level, use the show platform hardware throughput level
boost command. If there are not enough licenses, it shows an Out of Compliance (OOC) message, and
the throughput does not take effect even after the device is reloaded.

Return of license:
• The device is in the smart license mode with boost performance command configured.
• Use show running-config show license summaryand the license usage commands to display the boost
performance information from the smart account.
• Use the no platform hardware throughput level boost command to disable the functionality.

Note The command is removed from the configuration, but the license is released only after the device is
reloaded.
The throughput level does not take effect until the device is reloaded.
The license visibility is available till the device is reloaded.

One count of boost performance license is reduced from the usage pool, and one license is returned to its
original pool.
Cisco Software License to Smart Licensing
This is to describe a use-case when the device is moving from Cisco Software License(CSL) to Smart License
when boost performance license is on CSL. The boost performance behavior is determined by the availability
of the license in its Smart Account with Boost Performance activated in use in CSL:
To configure the throughput level, perform the following steps and to upgrade the throughput level use the
1 Configure the device with the platform hardware throughput level boost command and then use show
running-config to check if the boost performance license is activated.
2 Use show license to verify if boost performance is in use and in a permanent license mode.
3 Enable smart license by license smart enable command. After registration in success, the license request
is sent to the smart portal for validation. Boost performance is valid if successful, no reload is required.
Otherwise the platform hardware throughput level boost is unattached from configuration. Boost
performance functionality is disabled after reload.

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 9
Installing the Software
Feature Licenses

4 During the transition but before the registration, we have to maintain the Evaluation mode for the license
if the is existing to avoid an extra reload later.
5 To exit global configuration mode, enter exit.
6 To save the configuration, enter the copy running-config startup-config command.
7 To reload the router enter reload. A reload is required to activate the throughput level.

Smart Licensing to Cisco Software Licensing

Below are two use-cases that describe what happens during the transition from Smart License to Cisco Software
License.
When boost performance is in use:
• Device # platform hardware throughput level boost
• Device# show license to ensure that Smart License and Boost performance licenses are enabled.
• Check the Smart License Account if the boost performance license is consumed from the corresponding
device.
• Remove Smart License
• Device# no license smart enable
• Check the availability of the boost performance license, you may decide to retain the boost command.
• No extra reload is required.

When boost performance is not in use:

• Use no platform hardware throughput level boost in the show running-configuration.
• Device # show license to check if smart license is enabled, but boost performance license is not in the
list.
• Check the Smart License Account, the boost performance license is not used from the corresponding
device.
• To remove Smart License, use no license smart enable
• Check the availability of the boost permanent license to add the boost keyword.
• Boost Performance is activated and is in-use after reload

Note If there is no permanent license available, then no boost performancecommand and

functionality is likely to change.

CME-SRST
The CME-SRST feature requires the uck9 technology package. To activate the CME-SRST feature license,
see Activating the CME-SRST Feature License, on page 11.

Cisco 4000 Series ISRs Software Configuration Guide

10 OL-29328-03
Installing the Software
Activating the CME-SRST Feature License

Activating the CME-SRST Feature License

Before You Begin
Ensure the following:
• License for uck9 technology package is available.
• The CME-SRST feature is configured.

SUMMARY STEPS

1. show license detail cme-srst

2. configure terminal
3. license accept end user agreement
4. exit
5. show license detail cme-srst
6. write memory

DETAILED STEPS

Command or Action Purpose

Step 1 show license detail cme-srst Displays the available CME-SRST license.
Note The EULA should be in NOT ACCEPTED
Example: state.
Router# show license detail cme-srst

Step 2 configure terminal Enters global configuration mode.

Example:
Router# configure terminal

Step 3 license accept end user agreement Configures a one-time acceptance of the EULA for the
CME-SRST license.
Example: Accept the EULA by typing YES.
Router# license accept end user agreement

Step 4 exit Exits global configuration mode.

Example:
Router# exit

Step 5 show license detail cme-srst Displays the available CME-SRST license.
Note The EULA should be in ACCEPTED
Example: state.
Router# show license detail cme-srst

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 11
Installing the Software
Unlicensed Feature: Example

Command or Action Purpose

Step 6 write memory Saves configuration.

Example:
Router# write memory

Unlicensed Feature: Example

If you try to use a feature that is part of a package that is not enabled, an error message is displayed.
In the following example, the crypto map command is called during configuration and an error message is
displayed. This is because, the feature associated with crypto map is part of the securityk9 package and the
securityk9 package is not enabled.
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#crypto map
^
% Invalid input detected at '^' marker.
Use the show license feature command to view the license features that are enabled. In the following example,
the securityk9 and the uck9 packages are not enabled.

Note ipbasek9 is provided by default.

Router# show license feature

Feature name Enforcement Evaluation Subscription Enabled RightToUse
appxk9 yes yes no yes yes
uck9 yes yes no no yes
securityk9 yes yes no no yes
ipbasek9 no no no yes yes

LED Indicators
For information on LEDs on the router, see "LED Indicators" in the "Overview" section of the Hardware
Installation Guide for the Cisco 4000 Series Integrated Services Routers.
For information on LEDs on the SSD Carrier Card NIM, see "Overview of the SSD Carrier Card NIM
(NIM-SSD)" in the "Installing and Upgrading Internal Modules and FRUs" section of the Hardware Installation
Guide for the Cisco 4000 Series Integrated Services Routers.

Related Documentation
For further information on software licenses, see Software Activation on Cisco Integrated Services Routers
and Cisco Integrated Service Routers G2.
For further information on obtaining and installing feature licenses, see Configuring the Cisco IOS Software
Activation Feature.

Cisco 4000 Series ISRs Software Configuration Guide

12 OL-29328-03
Installing the Software
How to Install and Upgrade the Software

How to Install and Upgrade the Software

To install or upgrade the software, use one of the following methods to use the software from a consolidated
package or an individual package. Also see Overview, on page 1.
• Managing and Configuring a Router to Run Using a Consolidated Package, on page 13
• Managing and Configuring a Router to Run Using Individual Packages, on page 17

Managing and Configuring a Router to Run Using a Consolidated Package

Note Do not use these procedures if you also need to install any optional subpackages or plan to upgrade
individual subpackages. See Managing and Configuring a Router to Run Using Individual Packages, on
page 17.

• Managing and Configuring a Consolidated Package Using copy and boot Commands, on page 13
• Configuring a Router to Boot the Consolidated Package via TFTP Using the boot Command: Example,
on page 14

Managing and Configuring a Consolidated Package Using copy and boot Commands
To upgrade a consolidated package, copy the consolidated package to the bootflash: directory on the router
using the copy command. After making this copy of the consolidated package, configure the router to boot
using the consolidated package file.
The following example shows the consolidated package file being copied to the bootflash: file system via
TFTP. The config register is then set to boot using boot system commands, and the boot system commands
instruct the router to boot using the consolidated package stored in the bootflash: file system. The new
configuration is then saved using the copy running-config startup-config command, and the system is then
reloaded to complete the process.
Router# dir bootflash:
Directory of bootflash:/
11 drwx 16384 Dec 4 2007 04:32:46 -08:00 lost+found
86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 .ssh
14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 .rollback_timer
28801 drwx 4096 Mar 18 2008 17:31:17 -07:00 .prst_sync
43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 .installer

928862208 bytes total (712273920 bytes free)

Router# copy tftp: bootflash:

Address or name of remote host []? 172.17.16.81
Source filename []? /auto/tftp-users/user/isr4400-universalk9.03.10.00.S.153-3.S-ext.SPA.bin
Destination filename [isr4400-universalk9.03.10.00.S.153-3.S-ext.SPA.bin]?
Accessing
tftp://172.17.16.81//auto/tftp-users/user/isr4400-universalk9.03.10.00.S.153-3.S-ext.SPA.bin
...
Loading /auto/tftp-users/user/isr4400-universalk9.03.10.00.S.153-3.S-ext.SPA.bin from
172.17.16.81 (via GigabitEthernet0):
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!
[OK - 208904396 bytes]

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 13
Installing the Software
How to Install and Upgrade the Software

208904396 bytes copied in 330.453 secs (632176 bytes/sec)

Router# dir bootflash:
Directory of bootflash:/
11 drwx 16384 Dec 4 2007 04:32:46 -08:00 lost+found
86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 .ssh
14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 .rollback_timer
28801 drwx 4096 Mar 18 2008 17:31:17 -07:00 .prst_sync
43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 .installer
12 -rw- 208904396 May 28 2008 16:17:34 -07:00
isr4400-universalk9.03.10.00.S.153-3.S-ext.SPA.bin
928862208 bytes total (503156736 bytes free)
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)# boot system flash bootflash:isr4400-universalk9.03.10.00.S.153-3.S-ext.SPA.bin
Router(config)# config-reg 0x2102
Router(config)# exit
Router# show run | include boot
boot-start-marker
boot system flash bootflash:isr4400-universalk9.03.10.00.S.153-3.S-ext.SPA.bin
boot-end-marker
Router# copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Router# reload

Configuring a Router to Boot the Consolidated Package via TFTP Using the boot Command:
Example
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#boot system tftp://10.81.116.4/rtp-isr4400-54/isr4400.bin
Router(config)#config-register 0x2102
Router(config)#exit
Router# show run | include boot
boot-start-marker
boot system tftp://10.81.116.4/rtp-isr4400-54/isr4400.bin
boot-end-marker
license boot level adventerprise
Router# copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
Router# reload
Proceed with reload? [confirm]
Sep 13 17:42:54.445 R0/0: %PMAN-5-EXITACTION: Process manager is exiting: process exit with

reload chassis code

Initializing Hardware ...

System integrity status: c0000600

Failures detected:
Boot FPGA corrupt

Key Sectors:(Primary,GOOD),(Backup,GOOD),(Revocation,GOOD)
Size of Primary = 2288 Backup = 2288 Revocation = 300

ROM:RSA Self Test Passed

ROM:Sha512 Self Test Passed
Self Tests Latency: 58 msec

System Bootstrap, Version 12.2(20120618:163328) [username-ESGROM_20120618_GAMMA 101],

DEVELOPMENT SOFTWARE
Copyright (c) 1994-2014 by cisco Systems, Inc.

Cisco 4000 Series ISRs Software Configuration Guide

14 OL-29328-03
Installing the Software
How to Install and Upgrade the Software

Compiled Mon 05/27/2014 12:39:32.05 by username

Current image running: Boot ROM0

Last reset cause: LocalSoft

Cisco ISR 4400 platform with 4194304 Kbytes of main memory

IP_ADDRESS: 172.18.42.119
IP_SUBNET_MASK: 255.255.255.0
DEFAULT_GATEWAY: 172.18.42.1
TFTP_SERVER: 10.81.116.4
TFTP_FILE: rtp-isr4400-54/isr4400.bin
TFTP_MACADDR: a4:4c:11:9d:ad:97
TFTP_VERBOSE: Progress
TFTP_RETRY_COUNT: 18
TFTP_TIMEOUT: 7200
TFTP_CHECKSUM: Yes
ETHER_PORT: 0

ETHER_SPEED_MODE: Auto Detect

link up...
Receiving rtp-isr4400-54/isr4400.bin from 10.81.116.4
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
File reception completed.
Boot image size = 424317088 (0x194a90a0) bytes

ROM:RSA Self Test Passed

ROM:Sha512 Self Test Passed
Self Tests Latency: 58 msec

Package header rev 1 structure detected

Calculating SHA-1 hash...done
validate_package: SHA-1 hash:
calculated 7294dffc:892a6c35:a7a133df:18c032fc:0670b303
expected 7294dffc:892a6c35:a7a133df:18c032fc:0670b303
Signed Header Version Based Image Detected

Using FLASH based Keys of type = PRIMARY KEY STORAGE

Using FLASH based Keys of type = ROLLOVER KEY STORAGE
RSA Signed DEVELOPMENT Image Signature Verification Successful.
Package Load Test Latency : 5116 msec
Image validated
%IOSXEBOOT-4-BOOT_ACTIVITY_LONG_TIME: (local/local): load_modules took: 2 seconds,
expected max time 2 seconds

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software, ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Experimental Version

15.4(20140527:095327)
[v154_3_s_xe313_throttle-BLD-BLD_V154_3_S_XE313_THROTTLE_LATEST_20140527_070027-ios 156]
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Tue 27-May-14 21:28 by mcpre

Cisco IOS-XE software, Copyright (c) 2005-2014 by cisco Systems, Inc.

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 15
Installing the Software
How to Install and Upgrade the Software

GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

[email protected].

Warning: the compile-time code checksum does not appear to be present.

cisco ISR4451/K9 (2RU) processor with 1133585K/6147K bytes of memory.
Processor board ID FGL1619100P
4 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
7393215K bytes of Compact flash at bootflash:.
7816688K bytes of USB flash at usb0:.

Press RETURN to get started!

Router>
Router>
Router>enable
Router# show version
Cisco IOS XE Software, Version BLD_V154_3_S_XE313_THROTTLE_LATEST_20140527_070027-ext
Cisco IOS Software, ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Experimental Version
15.4(20140527:095327)
v154_3_s_xe313_throttle-BLD-BLD_V154_3_S_XE313_THROTTLE_LATEST_20140527_070027-ios 156]

IOS XE Version: BLD_V154_3_S_XE313_THROTTLE_LATEST

Cisco IOS-XE software, Copyright (c) 2005-2014 by cisco Systems, Inc.

All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.

ROM: IOS-XE ROMMON

Router uptime is 0 minutes

Uptime for this control processor is 3 minutes
System returned to ROM by reload
System image file is "tftp://10.81.116.4/rtp-isr4400-54/isr4400.bin"
Last reload reason: Reload Command

This product contains cryptographic features and is subject to United

Cisco 4000 Series ISRs Software Configuration Guide

16 OL-29328-03
Installing the Software
Managing and Configuring a Router to Run Using Individual Packages

compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

[email protected].

License Level: adventerprise

License Type: EvalRightToUse
--More-- Next reload license Level: adventerprise

cisco ISR4451/K9 (2RU) processor with 1133585K/6147K bytes of memory.

Processor board ID FGL1619100P
4 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
7393215K bytes of Compact flash at bootflash:.
7816688K bytes of USB flash at usb0:.

Configuration register is 0x2102

Managing and Configuring a Router to Run Using Individual Packages

To choose between running individual packages or a consolidated package, see Overview, on page 1.
The following topics are included in this section:
• Installing Subpackages from a Consolidated Package, on page 17
• Installing a Firmware Subpackage, on page 28
• Installing Subpackages from a Consolidated Package on a Flash Drive, on page 22

Installing Subpackages from a Consolidated Package

Perform the following procedure to obtain the consolidated package from a TFTP server.
Another variation of this procedure obtains the consolidated package from a USB flash drive. This is described
in Installing Subpackages from a Consolidated Package on a Flash Drive, on page 22.

Before You Begin

Copy the consolidated package to the TFTP server.

SUMMARY STEPS

1. show version
2. dir bootflash:
3. show platform
4. mkdir bootflash: URL-to-directory-name
5. request platform software package expand file URL-to-consolidated-package to URL-to-directory-name
6. reload
7. boot URL-to-directory-name/packages.conf
8. show version installed

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 17
Installing the Software
Managing and Configuring a Router to Run Using Individual Packages

DETAILED STEPS

Command or Action Purpose

Step 1 show version Shows the version of software running on the router. This
can later be compared with the version of software to be
Example: installed.
Router# show version
Cisco IOS Software, IOS-XE Software
(X86_64_LINUX_IOSD-UNIVERSALK9-M), Experimental
Version 15.3(20120627:221639) [build_151722 111]
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Thu 28-Jun-12 15:17 by mcpre
.
.
.

Step 2 dir bootflash: Displays the previous version of software and that a
package is present.
Example:
Router# dir bootflash:

Step 3 show platform Displays the inventory.

Example:
Router# show platform
Chassis type: ISR4451/K9

Step 4 mkdir bootflash: URL-to-directory-name Creates a directory to save the expanded software image.
You can use the same name as the image to name the
Example: directory.
Router# mkdir bootflash:mydir

Step 5 request platform software package expand file Expands the software image from the TFTP server
URL-to-consolidated-package to URL-to-directory-name (URL-to-consolidated-package) into the directory used
to save the image (URL-to-directory-name), which was
Example: created in Step 4.
Router# request platform software package expand
file
bootflash:isr4400-universalk9-NIM.bin to
bootflash:mydir

Step 6 reload Enables ROMMON mode, which allows the software in

the consolidated file to be activated.
Example:
Router# reload
rommon >

Step 7 boot URL-to-directory-name/packages.conf Boots the consolidated package, by specifying the path
and name of the provisioning file: packages.conf.
Example:
rommon 1 > boot bootflash:mydir/packages.conf

Step 8 show version installed Displays the version of the newly installed software.

Example:
Router# show version installed
Package: Provisioning File, version: n/a, status:
active

Cisco 4000 Series ISRs Software Configuration Guide

18 OL-29328-03
Installing the Software
Managing and Configuring a Router to Run Using Individual Packages

Examples
The initial part of the example shows the consolidated package, isr4400-universalk9.164422SSA.bin, being
copied to the TFTP server. This is a prerequisite step. The remaining part of the example shows the consolidated
file, packages.conf, being booted.
Router# copy tftp:isr4400/isr4400-universalk9.164422SSA.bin bootflash:
Address or name of remote host []? 1.1.1.1
Destination filename [isr4400-universalk9.164422SSA.bin]?
Accessing tftp://1.1.1.1/isr4400/isr4400-universalk9.164422SSA.bin...
Loading isr4400/isr4400-universalk9.164422SSA.bin from 1.1.1.1 (via GigabitEthernet0):
!!!!!!!!
[OK - 410506248 bytes]

410506248 bytes copied in 338.556 secs (1212521 bytes/sec)

Router# show version

Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Experimental Version

15.3(20120627:221639) [build_151722 111]

IOS XE Version: 2012-06-28_15.31_mcpre

Cisco IOS-XE software, Copyright (c) 2005-2012 by cisco Systems, Inc.

ROM: IOS-XE ROMMON

Router uptime is 0 minutes

Uptime for this control processor is 3 minutes
System returned to ROM by reload
System image file is "tftp:isr4400/isr4400.bin"
Last reload reason: Reload Command

This product contains cryptographic features and is subject to United

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

[email protected].

License Level: adventerprise

License Type: EvalRightToUse
Next reload license Level: adventerprise
cisco ISR4451/K9 (2RU) processor with 1136676K/6147K bytes of memory.
Processor board ID FGL161611AB
4 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 19
Installing the Software
Managing and Configuring a Router to Run Using Individual Packages

4194304K bytes of physical memory.

7393215K bytes of Compact flash at bootflash:.

Configuration register is 0x8000

Router# dir bootflash:

Directory of bootflash:/

11 drwx 16384 May 3 2012 19:58:37 +00:00 lost+found

178465 drwx 4096 Jun 6 2012 15:20:20 +00:00 core
584065 drwx 4096 Jul 13 2012 19:19:00 +00:00 .prst_sync
405601 drwx 4096 May 3 2012 19:59:30 +00:00 .rollback_timer
113569 drwx 40960 Jul 13 2012 19:19:32 +00:00 tracelogs
64897 drwx 4096 May 3 2012 19:59:42 +00:00 .installer
13 -rw- 1305 May 7 2012 17:43:42 +00:00 startup-config
14 -rw- 1305 May 7 2012 17:43:55 +00:00 running-config
15 -r-- 1541 Jun 4 2012 18:32:41 +00:00 debug.conf
16 -rw- 1252 May 22 2012 19:58:39 +00:00 running-config-20120522
519169 drwx 4096 Jun 4 2012 15:29:01 +00:00 vman_fdb

7451738112 bytes total (7067635712 bytes free)

Router# show platform

Chassis type: ISR4451/K9

Slot Type State Insert time (ago)

--------- ------------------- --------------------- -----------------
0 ISR4451/K9 ok 15:57:33
0/0 ISR4451-6X1GE ok 15:55:24
1 ISR4451/K9 ok 15:57:33
1/0 SM-1T3/E3 ok 15:55:24
2 ISR4451/K9 ok 15:57:33
2/0 SM-1T3/E3 ok 15:55:24
R0 ISR4451/K9 ok, active 15:57:33
F0 ISR4451-FP ok, active 15:57:33
P0 Unknown ps, fail never
P1 XXX-XXXX-XX ok 15:56:58
P2 ACS-4450-FANASSY ok 15:56:58

Slot CPLD Version Firmware Version

--------- ------------------- ---------------------------------------
0 12090323 15.3(01r)S [ciscouser-ISRRO...
1 12090323 15.3(01r)S [ciscouser-ISRRO...
2 12090323 15.3(01r)S [ciscouser-ISRRO...
R0 12090323 15.3(01r)S [ciscouser-ISRRO...
F0 12090323 15.3(01r)S [ciscouser-ISRRO...

Router# mkdir bootflash:isr4400-universalk9.dir1

Create directory filename [isr4400-universalk9.dir1]?
Created dir bootflash:/isr4400-universalk9.dir1
Router# request platform software package expand file bootflash:isr4400-universalk9.NIM.bin

to bootflash:isr4400-universalk9.dir1
Verifying parameters
Validating package type
Copying package files
SUCCESS: Finished expanding all-in-one software package.

Router# reload
Proceed with reload? [confirm]

*Jul 13 19:39:06.354: %SYS-5-RELOAD: Reload requested by console.Reload Reason: Reload

Command.

rommon 1 > boot bootflash:isr4400-universalk9.dir1/packages.conf

File size is 0x00002836

Located isr4400-universalk9.dir1/packages.conf
Image size 10294 inode num 324484, bks cnt 3 blk size 8*512
#
File is comprised of 1 fragments (33%)

Cisco 4000 Series ISRs Software Configuration Guide

20 OL-29328-03
Installing the Software
Managing and Configuring a Router to Run Using Individual Packages

is_valid_sha1hash: SHA-1 hash:

calculated 62f6235a:fc98eb3a:85ce183e:834f1cb3:8a1f71d1
expected 62f6235a:fc98eb3a:85ce183e:834f1cb3:8a1f71d1
File size is 0x04b3dc00
Located isr4400-universalk9.dir1/isr4400-mono-universalk9-build_164422SSA.pkg
Image size 78896128 inode num 324491, bks cnt 19262 blk size 8*512
##############################################################################################
File is comprised of 21 fragments (0%)
.....

Router# show version installed

Package: Provisioning File, version: n/a, status: active
File: bootflash:isr4400-universalk9.dir1/packages.conf, on: RP0
Built: n/a, by: n/a
File SHA1 checksum: ad09affd3f8820f4844f27acc1add502e0b8f459

Package: rpbase, version: 2012-07-10_16.22_mcpre, status: active

File: bootflash:isr4400-universalk9.dir1/isr4400-mono-universalk9-build_164422SSA.pkg, on:
RP0
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 5e95c9cbc4eaf5a4a5a1ac846ee2d0f41d1a026b

Package: firmware_attributes, version: 2012-07-10_16.22_mcpre, status: active

File: bootflash:isr4400-universalk9.dir1/isr4400-firmware_attributes_164422SSA.pkg, on:
RP0/0
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 71614f2d9cbe7f96d3c6e99b67d514bd108c6c99

Package: firmware_dsp_sp2700, version: 2012-07-10_16.22_mcpre, status: active

File: bootflash:isr4400-universalk9.dir1/isr4400-firmware_dsp_164422SSA.pkg, on: RP0/0
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 8334565edf7843fe246783b1d5c6ed933d96d79e
Package: firmware_fpge, version: 2012-07-10_16.22_mcpre, status: active
File: bootflash:isr4400-universalk9.dir1/isr4400-firmware_fpge_164422SSA.pkg, on: RP0/0
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: eb72900ab32c1c50652888ff486cf370ac901dd7

Package: firmware_sm_1t3e3, version: 2012-07-10_16.22_mcpre, status: active

File: bootflash:isr4400-universalk9.dir1/isr4400-firmware_sm_1t3e3_164422SSA.pkg, on: RP0/0
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 803005f15d8ea71ab088647e2766727ac2269871

Package: rpcontrol, version: 2012-07-10_16.22_mcpre, status: active

File: bootflash:isr4400-universalk9.dir1/isr4400-mono-universalk9_164422SSA.pkg, on: RP0/0
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 980fd58fe581e9346c44417b451d1c09ebb640c2

Package: rpios-universalk9, version: dir1, status: active

File: bootflash:isr4400-universalk9.dir1/isr4400-mono-universalk9_164422SSA.pkg, on: RP0/0
Built: 2012-07-10_16.23, by: mcpre
File SHA1 checksum: 27084f7e30a1d69d45a33e05d1b00345040799fb
Package: rpaccess, version: 2012-07-10_16.22_mcpre, status: active
File: bootflash:isr4400-universalk9.dir1/isr4400-mono-universalk9_164422SSA.pkg, on: RP0/0
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 0119802deda2da91c38473c47a998fb3ed423448

Package: firmware_attributes, version: 2012-07-10_16.22_mcpre, status: n/a

File: bootflash:isr4400-universalk9.dir1/isr4400-firmware_attributes_164422SSA.pkg, on:
RP0/1
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 71614f2d9cbe7f96d3c6e99b67d514bd108c6c99

Package: firmware_dsp_sp2700, version: 2012-07-10_16.22_mcpre, status: n/a

File: bootflash:isr4400-universalk9.dir1/isr4400-firmware_dsp_164422SSA.pkg, on: RP0/1
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 8334565edf7843fe246783b1d5c6ed933d96d79e

Package: firmware_fpge, version: 2012-07-10_16.22_mcpre, status: n/a

File: bootflash:isr4400-universalk9.dir1/isr4400-firmware_fpge-BLD-BLD_MCP_DEV_LATEST_20120710
_164422SSA.pkg, on: RP0/1

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 21
Installing the Software
Managing and Configuring a Router to Run Using Individual Packages

Built: 2012-07-10_16.22, by: mcpre

File SHA1 checksum: eb72900ab32c1c50652888ff486cf370ac901dd7

Package: firmware_sm_1t3e3, version: 2012-07-10_16.22_mcpre, status: n/a

File: bootflash:isr4400-universalk9.dir1/isr4400-firmware_sm_1t3e3-BLD-BLD_MCP_DEV_LATEST_
20120710_164422SSA.pkg, on: RP0/1
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 803005f15d8ea71ab088647e2766727ac2269871

Package: rpcontrol, version: 2012-07-10_16.22_mcpre, status: n/a

File: bootflash:isr4400-universalk9.dir1/isr4400-rpcontrol-BLD-BLD_MCP_DEV_LATEST_20120710_
164422SSA.pkg, on: RP0/1
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 980fd58fe581e9346c44417b451d1c09ebb640c2

Package: rpios-universalk9, version: 2012-07-10_16.23_mcpre, status: n/a

File: bootflash:isr4400-universalk9.dir1/isr4400-rpios-universalk9-BLD-BLD_MCP_DEV_LATEST_
20120710_164422SSA.pkg, on: RP0/1
Built: 2012-07-10_16.23, by: mcpre
File SHA1 checksum: 27084f7e30a1d69d45a33e05d1b00345040799fb

Package: rpaccess, version: 2012-07-10_16.22_mcpre, status: n/a

File: bootflash:isr4400-universalk9.dir1/isr4400-rpaccess-BLD-BLD_MCP_DEV_LATEST_20120710_
164422SSA.pkg, on: RP0/1
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 0119802deda2da91c38473c47a998fb3ed423448

Package: rpbase, version: 2012-07-10_16.22_mcpre, status: n/a

File: bootflash:isr4400-universalk9.dir1/isr4400-rpbase-BLD-BLD_MCP_DEV_LATEST_20120710_
164422SSA.pkg, on: RP1
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 5e95c9cbc4eaf5a4a5a1ac846ee2d0f41d1a026b

Package: firmware_attributes, version: 2012-07-10_16.22_mcpre, status: n/a

File: bootflash:isr4400-universalk9.dir1/isr4400-firmware_attributes-BLD-BLD_MCP_DEV_LATEST
_20120710_164422SSA.pkg, on: RP1/0
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 71614f2d9cbe7f96d3c6e99b67d514bd108c6c99

Package: firmware_dsp_sp2700, version: 2012-07-10_16.22_mcpre, status: n/a

File: bootflash:isr4400-universalk9.dir1/isr4400-firmware_dsp_sp2700-BLD-BLD_MCP_DEV_LATEST_
20120710_164422SSA.pkg, on: RP1/0
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 8334565edf7843fe246783b1d5c6ed933d96d79e

Package: firmware_fpge, version: 2012-07-10_16.22_mcpre, status: n/a

Installing Subpackages from a Consolidated Package on a Flash Drive

The steps for installing subpackages from a consolidated package on a USB flash drive are similar to those
described in Installing Subpackages from a Consolidated Package .

Step 1 show version

Step 2 dir usbn:
Step 3 show platform
Step 4 mkdir bootflash:URL-to-directory-name
Step 5 request platform software package expand fileusbn: package-name to URL-to-directory-name
Step 6 reload
Step 7 boot URL-to-directory-name/packages.conf
Step 8 show version installed

Cisco 4000 Series ISRs Software Configuration Guide

22 OL-29328-03
Installing the Software
How to Install and Upgrade the Software for Cisco IOS XE Denali Release16.3

How to Install and Upgrade the Software for Cisco IOS XE Denali Release16.3
To install or upgrade the software, use one of the following methods to use the software from a consolidated
package or an individual package. Also see Overview, on page 1.
• Managing and Configuring a Router to Run Using a Consolidated Package, on page 13
• Managing and Configuring a Router to Run Using Individual Packages, on page 17
• Configuring a Router to Boot the Consolidated Package via TFTP Using the boot Command: Example,
on page 14
• Upgrading to Cisco IOS XE Denali Release 16.3, on page 23

Upgrading to Cisco IOS XE Denali Release 16.3

Upgrading the device to Cisco IOS XE Denali Release 16.3 for the first time uses the same procedures as
specified in the earlier section. In addition, Cisco IOS XE Denali Release 16.3 requires a minimum ROMMON
version. When the device boots up with Cisco IOS XE Denali image for the first time, the device checks the
installed version of the ROMMON, and upgrades if the system is running an older version. During the upgrade,
do not power cycle the device. The system automatically power cycles the device after the new ROMMON
is installed. After the installation, the system will boot up with the Cisco IOS XE image as normal.

Note When the device boots up for first time and if the device requires an upgrade, the entire boot process may
take several minutes. This process will be longer than a normal boot due to the ROMMON upgrade.
The following example illustrates the boot process of a consolidated package:
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#boot system tftp://10.81.116.4/rtp-isr4400-54/isr4400.bin
Router(config)#config-register 0x2102
Router(config)#exit
Router# show run | include boot
boot-start-marker
boot system tftp://10.81.116.4/rtp-isr4400-54/isr4400.bin
boot-end-marker
license boot level adventerprise
Router# copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
Router# reload
Proceed with reload? [confirm]
Sep 13 17:42:54.445 R0/0: %PMAN-5-EXITACTION: Process manager is exiting: process exit with

reload chassis code

Initializing Hardware ...

System integrity status: c0000600

Key Sectors:(Primary,GOOD),(Backup,GOOD),(Revocation,GOOD)
Size of Primary = 2288 Backup = 2288 Revocation = 300

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 23
Installing the Software
How to Install and Upgrade the Software for Cisco IOS XE Denali Release16.3

ROM:RSA Self Test Passed

ROM:Sha512 Self Test Passed
Self Tests Latency: 58 msec

System Bootstrap, Version 12.2(20120618:163328) [username-ESGROM_20120618_GAMMA 101],

DEVELOPMENT SOFTWARE
Copyright (c) 1994-2014 by cisco Systems, Inc.
Compiled Mon 05/27/2014 12:39:32.05 by username

Current image running: Boot ROM0

Last reset cause: LocalSoft

Cisco ISR 4400 platform with 4194304 Kbytes of main memory

ETHER_SPEED_MODE: Auto Detect

link up...
Receiving rtp-isr4400-54/isr4400.bin from 10.81.116.4
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
File reception completed.
Boot image size = 504063931 (0x1e0b67bb) bytes

ROM:RSA Self Test Passed

ROM:Sha512 Self Test Passed
Self Tests Latency: 58 msec

Package header rev 1 structure detected

Using FLASH based Keys of type = PRIMARY KEY STORAGE

Using FLASH based Keys of type = ROLLOVER KEY STORAGE
RSA Signed DEVELOPMENT Image Signature Verification Successful.
Package Load Test Latency : 5116 msec
Image validated

Detected old ROMMON version 12.2(20150910:184432), upgrade required

Upgrading to newer ROMMON version required by this version of IOS-XE, do not power cycle
the system. A reboot will automatically occur for the new ROMMON to take effect.
selected : 1
Booted : 1
Reset Reason: 1

Info: Upgrading entire flash from the rommon package

Switching to ROM 0
Upgrade image MD5 signature is b702a0a59a46a20a4924f9b17b8f0887
Upgrade image MD5 signature verification is b702a0a59a46a20a4924f9b17b8f0887
Switching back to ROM 1
ROMMON upgrade complete.

To make the new ROMMON permanent, you must restart the RP.
ROMMON upgrade successful. Rebooting for upgrade to take effect.

Cisco 4000 Series ISRs Software Configuration Guide

24 OL-29328-03
Installing the Software
How to Install and Upgrade the Software for Cisco IOS XE Denali Release16.3

Initializing Hardware ...

System integrity status: 00300610

Key Sectors:(Primary,GOOD),(Backup,GOOD),(Revocation,GOOD)
Size of Primary = 2288 Backup = 2288 Revocation = 300

ROM:RSA Self Test Passed

Expected hash:
ddaf35a193617abacc417349ae204131
12e6fa4e89a97ea20a9eeee64b55d39a
2192992a274fc1a836ba3c23a3feebbd
454d4423643ce80e2a9ac94fa54ca49f

Obtained hash:
ddaf35a193617abacc417349ae204131
12e6fa4e89a97ea20a9eeee64b55d39a
2192992a274fc1a836ba3c23a3feebbd
454d4423643ce80e2a9ac94fa54ca49f
ROM:Sha512 Self Test Passed
Self Tests Latency: 418 msec
Rom image verified correctly

System Bootstrap, Version 12.2(20120618:163328) [username-ESGROM_20120618_GAMMA 101],

DEVELOPMENT SOFTWARE
Copyright (c) 1994-2014 by cisco Systems, Inc.
Compiled Mon 05/27/2014 12:39:32.05 by username

CPLD Version: 33 (MM/DD/YY): 06/23/14 Cisco ISR4351/K9 Slot:0

Current image running: Boot ROM1

Last reset cause: ResetRequest

Reading confreg 0x2102

Reading monitor variables from NVRAM

Enabling interrupts...done

Checking for PCIe device presence...done

Cisco ISR4351/K9 platform with 16777216 Kbytes of main memory

autoboot entry: NVRAM VALUES: bootconf: 0x0, autobootstate: 0

autobootcount: 0, autobootsptr: 0x0
Rommon upgrade requested
Flash upgrade reset 0 in progress
.......
Initializing Hardware ...

Checking for PCIe device presence...done

Reading confreg 2102
System integrity status: 0x300610
Key Sectors:(Primary, GOOD),(Backup,GOOD),(Revocation,GOOD)
Size of Primary = 2288 Backup = 2288 Revocation = 288
RSA Self Test Passed

Expected hash:
DDAF35A193617ABACC417349AE204131
12E6FA4E89A97EA20A9EEEE64B55D39A
2192992A274FC1A836BA3C23A3FEEBBD
454D4423643CE80E2A9AC94FA54CA49F

Obtained hash:
DDAF35A193617ABACC417349AE204131
12E6FA4E89A97EA20A9EEEE64B55D39A
2192992A274FC1A836BA3C23A3FEEBBD
454D4423643CE80E2A9AC94FA54CA49F
Sha512 Self Test Passed
Rom image verified correctly

System Bootstrap, Version 16.2(1r), RELEASE SOFTWARE

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 25
Installing the Software
How to Install and Upgrade the Software for Cisco IOS XE Denali Release16.3

Current image running: Upgrade in progress Boot ROM0

Last reset cause: BootRomUpgrade

ISR4351/K9 platform with 16777216 Kbytes of main memory

Cisco ISR 4400 platform with 4194304 Kbytes of main memory

ETHER_SPEED_MODE: Auto Detect

link up...
Receiving rtp-isr4400-54/isr4400.bin from 10.81.116.4
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
File reception completed.
Boot image size = 504063931 (0x1e0b67bb) bytes

Image Base is: 0x56834018

Image Size is: 0x1E089706
Package header rev 1 structure detected
Package type:30000, flags:0x0
IsoSize = 503874534
Parsing package TLV info:
000: 000000090000001D4B45595F544C565F - KEY_TLV_
010: 5041434B4147455F434F4D5041544942 - PACKAGE_COMPATIB
020: 494C495459000000000000090000000B - ILITY
030: 4652555F52505F545950450000000009 - FRU_RP_TYPE
040: 000000184B45595F544C565F5041434B - KEY_TLV_PACK
050: 4147455F424F4F544152434800000009 - AGE_BOOTARCH
060: 0000000E415243485F693638365F5459 - ARCH_i686_TY
070: 5045000000000009000000144B45595F - PE KEY_
080: 544C565F424F4152445F434F4D504154 - TLV_BOARD_COMPAT
090: 0000000900000012424F4152445F6973 - BOARD_is
0A0: 72343330305F54595045000000000009 - r4300_TYPE
0B0: 000000184B45595F544C565F43525950 - KEY_TLV_CRYP
0C0: 544F5F4B4559535452494E4700000009 - TO_KEYSTRING

TLV: T=9, L=29, V=KEY_TLV_PACKAGE_COMPATIBILITY

TLV: T=9, L=11, V=FRU_RP_TYPE
TLV: T=9, L=24, V=KEY_TLV_PACKAGE_BOOTARCH
TLV: T=9, L=14, V=ARCH_i686_TYPE
TLV: T=9, L=20, V=KEY_TLV_BOARD_COMPAT
TLV: T=9, L=18, V=BOARD_isr4300_TYPE
TLV: T=9, L=24, V=KEY_TLV_CRYPTO_KEYSTRING
TLV: T=9, L=10, V=EnCrYpTiOn
TLV: T=9, L=11, V=CW_BEGIN=$$
TLV: T=9, L=19, V=CW_FAMILY=$isr4300$
TLV: T=9, L=59, V=CW_IMAGE=$isr4300-universalk9.2016-06-29_23.31_paj.SSA.bin$
TLV: T=9, L=19, V=CW_VERSION=$16.3.1$
TLV: T=9, L=52, V=CW_DESCRIPTION=$Cisco IOS Software, IOS-XE Software$
TLV: T=9, L=9, V=CW_END=$$
Found DIGISIGN TLV type 12 length = 392
RSA Self Test Passed

Expected hash:
DDAF35A193617ABACC417349AE204131
12E6FA4E89A97EA20A9EEEE64B55D39A
2192992A274FC1A836BA3C23A3FEEBBD
454D4423643CE80E2A9AC94FA54CA49F

Cisco 4000 Series ISRs Software Configuration Guide

26 OL-29328-03
Installing the Software
How to Install and Upgrade the Software for Cisco IOS XE Denali Release16.3

Obtained hash:
DDAF35A193617ABACC417349AE204131
12E6FA4E89A97EA20A9EEEE64B55D39A
2192992A274FC1A836BA3C23A3FEEBBD
454D4423643CE80E2A9AC94FA54CA49F
Sha512 Self Test Passed
Found package arch type ARCH_i686_TYPE
Found package FRU type FRU_RP_TYPE
Calculating SHA-1 hash...Validate package: SHA-1 hash:
calculated 8B082C48:35C23C9E:8A091441:D6FACEE6:B5111533
expected 8B082C48:35C23C9E:8A091441:D6FACEE6:B5111533

Image validated

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

cisco Systems, Inc.

170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software, ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Experimental Version

16.3(20160527:095327)
[v163_throttle]
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Tue 27-May-16 21:28 by mcpre

Cisco IOS-XE software, Copyright (c) 2005-2016 by cisco Systems, Inc.

This product contains cryptographic features and is subject to United

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

[email protected].

Warning: the compile-time code checksum does not appear to be present.

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 27
Installing the Software
Installing a Firmware Subpackage

Press RETURN to get started!

Installing a Firmware Subpackage

Before You Begin
Obtain a consolidated package that contains your required firmware package and expand the package. (See
Managing and Configuring a Router to Run Using Individual Packages, on page 17.) Make a note of the
location and name of the firmware package and use this information in the steps below for
URL-to-package-name.
You can install a firmware subpackage if the router has been configured using, for example, Managing and
Configuring a Router to Run Using Individual Packages, on page 17.
Firmware subpackages are not released individually. You can select a firmware package from within a
consolidated package after expanding the consolidated package. The firmware package can then be installed
as shown in the procedure below.

Note Read the Release Notes document pertaining to the consolidated package to verify that the firmware within
the consolidated package is compatible with the version of Cisco IOS XE software that is currently installed
on a router.

SUMMARY STEPS

DETAILED STEPS

Command or Action Purpose

Cisco 4000 Series ISRs Software Configuration Guide

28 OL-29328-03
Installing the Software
Installing a Firmware Subpackage

Command or Action Purpose

.
.

Step 2 dir bootflash: Displays the previous version of software and that a
package is present.
Example:
Router# dir bootflash:

Step 3 show platform Checks the inventory.

Also see the example in Installing Subpackages from a
Example: Consolidated Package
Router# show platform
Chassis type: ISR4451/K9

Step 5 request platform software package expand file Expands the software image from the TFTP server
URL-to-consolidated-package to URL-to-directory-name (URL-to-consolidated-package) into the directory used to
save the image (URL-to-directory-name), which was
Example: created in the Step 4.
Router# request platform software package expand
file
bootflash:isr4400-universalk9-NIM.bin to
bootflash:mydir

Step 6 reload Enables ROMMON mode, which allows the software in

the consolidated file to be activated.
Example:
Router# reload
rommon >

Step 7 boot URL-to-directory-name /packages.conf Boots the consolidated package by specifying the path and
name of the provisioning file: packages.conf.
Example:
rommon 1 > boot bootflash:mydir/packages.conf

Step 8 show version installed Displays the version of the newly installed software.

Example:
Router# show version installed
Package: Provisioning File, version: n/a, status:
active

Examples
The initial part of the following example shows the consolidated package, isr4400-universalk9.164422SSA.bin,
being copied to the TFTP server. This is a prerequisite step. The remaining part of the example shows the
consolidated file, packages.conf, being booted.
Router# tftp:isr4400/isr4400-universalk9.164422SSA.bin bootflash:
Address or name of remote host []? 1.1.1.1
Destination filename [isr4400-universalk9.164422SSA.bin]?

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 29
Installing the Software
Installing a Firmware Subpackage

Accessing tftp://1.1.1.1/isr4400/isr4400-universalk9.164422SSA.bin...
Loading isr4400/isr4400-universalk9.164422SSA.bin from 1.1.1.1 (via GigabitEthernet0):
!!!!!!!!
[OK - 410506248 bytes]

410506248 bytes copied in 338.556 secs (1212521 bytes/sec)

Router# show version

Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Experimental Version

15.3(20120627:221639) [build_151722 111]

IOS XE Version: 2012-06-28_15.31_mcpre

Cisco IOS-XE software, Copyright (c) 2005-2012 by cisco Systems, Inc.

ROM: IOS-XE ROMMON

Router uptime is 0 minutes

Uptime for this control processor is 3 minutes
System returned to ROM by reload
System image file is "tftp:isr4400/isr4400.bin"
Last reload reason: Reload Command

This product contains cryptographic features and is subject to United

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

[email protected].

License Level: adventerprise

Configuration register is 0x8000

Router# dir bootflash:

Directory of bootflash:/

11 drwx 16384 May 3 2012 19:58:37 +00:00 lost+found

Cisco 4000 Series ISRs Software Configuration Guide

30 OL-29328-03
Installing the Software
Installing a Firmware Subpackage

14 -rw- 1305 May 7 2012 17:43:55 +00:00 running-config

15 -r-- 1541 Jun 4 2012 18:32:41 +00:00 debug.conf
16 -rw- 1252 May 22 2012 19:58:39 +00:00 running-config-20120522
519169 drwx 4096 Jun 4 2012 15:29:01 +00:00 vman_fdb

7451738112 bytes total (7067635712 bytes free)

Router# show platform

Chassis type: ISR4451/K9

Slot Type State Insert time (ago)

Slot CPLD Version Firmware Version

Router# mkdir bootflash:isr4400-universalk9.dir1

Create directory filename [isr4400-universalk9.dir1]?
Created dir bootflash:/isr4400-universalk9.dir1
Router# request platform software package expand file bootflash:isr4400-universalk9.NIM.bin
to
bootflash:isr4400-universalk9.dir1
Verifying parameters
Validating package type
Copying package files
SUCCESS: Finished expanding all-in-one software package.

Router# reload
Proceed with reload? [confirm]

*Jul 13 19:39:06.354: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload

Command.

rommon 1 > boot bootflash:isr4400-universalk9.dir1/packages.conf

File size is 0x00002836

Located isr4400-universalk9.dir1/packages.conf
Image size 10294 inode num 324484, bks cnt 3 blk size 8*512
#
File is comprised of 1 fragments (33%)

is_valid_sha1hash: SHA-1 hash:

Router# show version installed

Package: Provisioning File, version: n/a, status: active

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 31
Installing the Software
Installing a Firmware Subpackage

File: bootflash:isr4400-universalk9.dir1/packages.conf, on: RP0

Built: n/a, by: n/a
File SHA1 checksum: ad09affd3f8820f4844f27acc1add502e0b8f459

Package: rpbase, version: 2012-07-10_16.22_mcpre, status: active

File: bootflash:isr4400-universalk9.dir1/isr4400-mono-universalk9-build_164422SSA.pkg, on:
RP0
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 5e95c9cbc4eaf5a4a5a1ac846ee2d0f41d1a026b

Package: firmware_attributes, version: 2012-07-10_16.22_mcpre, status: active

File: bootflash:isr4400-universalk9.dir1/isr4400-firmware_attributes_164422SSA.pkg, on:
RP0/0
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 71614f2d9cbe7f96d3c6e99b67d514bd108c6c99

Package: firmware_dsp_sp2700, version: 2012-07-10_16.22_mcpre, status: active

Package: firmware_sm_1t3e3, version: 2012-07-10_16.22_mcpre, status: active

File: bootflash:isr4400-universalk9.dir1/isr4400-firmware_sm_1t3e3_164422SSA.pkg, on: RP0/0
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 803005f15d8ea71ab088647e2766727ac2269871

Package: rpcontrol, version: 2012-07-10_16.22_mcpre, status: active

File: bootflash:isr4400-universalk9.dir1/isr4400-mono-universalk9_164422SSA.pkg, on: RP0/0
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 980fd58fe581e9346c44417b451d1c09ebb640c2

Package: rpios-universalk9, version: dir1, status: active

Package: firmware_attributes, version: 2012-07-10_16.22_mcpre, status: n/a

File: bootflash:isr4400-universalk9.dir1/isr4400-firmware_attributes_164422SSA.pkg, on:
RP0/1
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 71614f2d9cbe7f96d3c6e99b67d514bd108c6c99

Package: firmware_dsp_sp2700, version: 2012-07-10_16.22_mcpre, status: n/a

File: bootflash:isr4400-universalk9.dir1/isr4400-firmware_dsp_164422SSA.pkg, on: RP0/1
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 8334565edf7843fe246783b1d5c6ed933d96d79e

Package: firmware_fpge, version: 2012-07-10_16.22_mcpre, status: n/a

File: bootflash:isr4400-universalk9.dir1/isr4400-firmware_fpge-BLD-BLD_MCP_DEV_LATEST_
20120710_164422SSA.pkg, on: RP0/1
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: eb72900ab32c1c50652888ff486cf370ac901dd7

Package: firmware_sm_1t3e3, version: 2012-07-10_16.22_mcpre, status: n/a

Package: rpcontrol, version: 2012-07-10_16.22_mcpre, status: n/a

Cisco 4000 Series ISRs Software Configuration Guide

32 OL-29328-03
Installing the Software
Upgrading the Firmware on xDSL NIMs

Package: rpios-universalk9, version: 2012-07-10_16.23_mcpre, status: n/a

Package: rpaccess, version: 2012-07-10_16.22_mcpre, status: n/a

Package: rpbase, version: 2012-07-10_16.22_mcpre, status: n/a

Package: firmware_attributes, version: 2012-07-10_16.22_mcpre, status: n/a

File: bootflash:isr4400-universalk9.dir1/isr4400-firmware_attributes-BLD-BLD_MCP_DEV_LATEST_
20120710_164422SSA.pkg, on: RP1/0
Built: 2012-07-10_16.22, by: mcpre
File SHA1 checksum: 71614f2d9cbe7f96d3c6e99b67d514bd108c6c99

Package: firmware_dsp_sp2700, version: 2012-07-10_16.22_mcpre, status: n/a

Package: firmware_fpge, version: 2012-07-10_16.22_mcpre, status: n/a

Upgrading the Firmware on xDSL NIMs

To upgrade the firmware on a xDSL Network Interface Module (NIM), perform these steps:

Before You Begin

When you boot the router in packages.conf mode with the Cisco IOS XE image (super package) during the
installation period, you can upgrade or downgrade the firmware without reloading the router. You need to
follow the steps described in Installing a Firmware Subpackage, on page 28 before proceeding with the
firmware upgrade.
If you do not boot the router in packages.conf mode with the Cisco IOS XE image, you need to follow the
below prerequisites before proceeding with the firmware upgrade:
• Copy the firmware subpackage (NIM firmware) into bootflash:/mydir.
• Send a request to the platform software package expand file boot flash:/mydir/<IOS-XE image> to
expand the super package.
• Reload the hardware module subslot to boot the module with the new firmware.
• Verify that the module is booted up with the new firmware using the show platform software subslot
x/y module firmware command.

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 33
Installing the Software
Upgrading the Firmware on xDSL NIMs

SUMMARY STEPS

1. copy Cisco IOS XE image into bootflash: mydir.

2. request platform software package expand file bootflash:/mydir /<IOS-XE image to expand super
package.
3. reload.
4. boot bootflash:mydir/ /packages.conf.
5. copy NIM firmware subpackage to the folder bootflash:mydir/.
6. request platform software package install rp 0 file bootflash:/mydir/<firmware subpackage>.
7. hw-module subslot x/y reload to boot the module with the new firmware.
8. show platform software subslot 0/2 module firmware to verify that the module is booted up with the
new firmware.

DETAILED STEPS

Command or Action Purpose

Step 1 copy Cisco IOS XE image into bootflash: mydir. Creates a directory to save the
expanded software image.
Example: You can use the same name as the
Router# mkdir bootflash:mydir
image to name the directory.

Step 2 request platform software package expand file bootflash:/mydir /<IOS-XE image Expands the platform software
to expand super package. package to super package.

Example:
Router# request platform software package expand file
bootflash:/mydir/isr4400-universalk9.03.14.00.S.155-1.S-std.SPA.bin

Step 3 reload. Enables ROMMON mode, which

allows the software in the super
Example: package file to be activated.
Router# reload
rommon >

Step 4 boot bootflash:mydir/ /packages.conf. Boots the super package by

specifying the path and name of the
Example: provisioning file: packages.conf.
rommon 1 > boot bootflash:mydir/packages.conf

Step 5 copy NIM firmware subpackage to the folder bootflash:mydir/. Copies the NIM firmware
subpackage into bootflash:mydir.
Example:
Router#copy
bootflash:isr4400-firmware_nim_xdsl.2014-11-17_11.05_39n.SSA.pkg
bootflash:mydir/

Step 6 request platform software package install rp 0 file bootflash:/mydir/<firmware Installs the software package.
subpackage>.

Cisco 4000 Series ISRs Software Configuration Guide

34 OL-29328-03
Installing the Software
Upgrading the Firmware on xDSL NIMs

Command or Action Purpose

Example:
Router#equest platform software package install rp 0 file
bootflash:mydir/isr4400-firmware_nim_xdsl.2014-11-17_11.05_39n.SSA.pkg

Step 7 hw-module subslot x/y reload to boot the module with the new firmware. Reloads the hardware module subslot
and boots the module with the new
Example: firmware.
Router#hw-module subslot 0/2 reload

Step 8 show platform software subslot 0/2 module firmware to verify that the module Displays the version of the newly
is booted up with the new firmware. installed firmware.

Example:
Router# show platform software subslot 0/2 module firmware
Pe

Examples
The following example shows how to perform firmware upgrade in a router module:
Routermkdir bootflash:mydir
Create directory filename [mydir]?
Created dir bootflash:/mydir
Router#c
Router#copy bootflash:isr4400-universalk9.03.14.00.S.155-1.S-std.SPA.bin bootflash:mydir/
Destination filename [mydir/isr4400-universalk9.03.14.00.S.155-1.S-std.SPA.bin]?
Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
CCCCC
425288648 bytes copied in 44.826 secs (9487544 bytes/sec)
Router#
Router#
Router#dir bootflash:mydir
Directory of bootflash:/mydir/

632738 -rw- 425288648 Dec 12 2014 09:16:42 +00:00

isr4400-universalk9.03.14.00.S.155-1.S-std.SPA.bin

7451738112 bytes total (474025984 bytes free)

Router#

Router#request platform software package

expand file bootflash:/mydir/isr4400-universalk9.03.14.00.S.155-1.S-std.SPA.bin
Verifying parameters
Validating package type
Copying package files
SUCCESS: Finished expanding all-in-one software package.

Router#reload
Proceed with reload? [confirm]

*Dec 12 09:26:09.874: %SYS-5-RELOAD: Reload requested by console. Reload Reason:

Reload Command.Dec 12 09:26:25.156 R0/0: %PMAN-5-EXITACTION: Process manager is exiting:
process exit with reload chassis code

Initializing Hardware ...

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 35
Installing the Software
Upgrading the Firmware on xDSL NIMs

System integrity status: 00000610

Rom image verified correctly
System Bootstrap, Version 15.3(3r)S1, RELEASE SOFTWARE
Copyright (c) 1994-2013 by cisco Systems, Inc.

Current image running: Boot ROM0

Last reset cause: LocalSoft

Cisco ISR4451-X/K9 platform with 4194304 Kbytes of main memory

rommon 1 boot bootflash:mydir/packages.conf

File size is 0x000028f1

Located mydir/packages.conf
Image size
10481 inode num 632741, bks cnt 3 blk size 8*512

#
File size is 0x150ae3cc
Located mydir/isr4400-mono-universalk9.03.14.00.S.155-1.S-std.SPA.pkg
Image size 353035212 inode num 356929, bks cnt 86191 blk size 8*512
###################################################################
######################################################################
Boot image size = 353035212 (0x150ae3cc) bytes

Package header rev 1 structure detected

Calculating SHA-1 hash...done
validate_package: SHA-1 hash:
calculated 8e966678:8afb08f4:8a88bb8f:fe591121:8bddf4b3
expected 8e966678:8afb08f4:8a88bb8f:fe591121:8bddf4b3

RSA Signed RELEASE Image Signature Verification Successful.

Package Load Test Latency : 3799 msec
Image validated
Dec 12 09:28:50.338 R0/0: %FLASH_CHECK-3-DISK_QUOTA: Flash disk quota exceeded
[free space is 61864 kB] - Please clean up files on bootflash.

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

cisco Systems, Inc.

170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software, ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.5(1)S,

RELEASE SOFTWARE (fc5)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Thu 20-Nov-14 18:28 by mcpre

Cisco 4000 Series ISRs Software Configuration Guide

36 OL-29328-03
Installing the Software
Upgrading the Firmware on xDSL NIMs

This product contains cryptographic features and is subject to United

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

[email protected].

cisco ISR4451-X/K9 (2RU) processor with 1681388K/6147K bytes of memory.

Processor board ID FTX1736AJUT
2 Ethernet interfaces
4 Gigabit Ethernet interfaces
2 ATM interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
7393215K bytes of flash memory at bootflash:.

Press RETURN to get started!

*Dec 12 09:28:58.922:
%IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL:
Module name = esg Next reboot level = appxk9 and License = appxk9
*Dec 12 09:28:58.943:
%IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL:
Module name = esg Next reboot level = ipbasek9 and License = ipbasek9
*Dec 12 09:28:58.981:
%ISR_THROUGHPUT-6-LEVEL: Throughput level has been set to 1000000 kbps
*Dec 12 09:29:13.302: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
*Dec 12 09:29:14.142: %LINK-3-UPDOWN: Interface Lsmpi0, changed state to up
*Dec 12 09:29:14.142: %LINK-3-UPDOWN: Interface EOBC0, changed state to up
*Dec 12 09:29:14.142: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to down
*Dec 12 09:29:14.142: %LINK-3-UPDOWN: Interface LIIN0, changed state to up
*Dec 12 09:28:51.438: %CMRP-3-PFU_MISSING:cmand: The platform does not detect a power
supply in slot 1
*Dec 12 09:29:01.256: %CMLIB-6-THROUGHPUT_VALUE:cmand: Throughput license found, throughput
set to 1000000 kbps
*Dec 12 09:29:03.223: %CPPHA-7-START:cpp_ha: CPP 0 preparing ucode
*Dec 12 09:29:03.238: %CPPHA-7-START:cpp_ha: CPP 0 startup init
*Dec 12 09:29:11.335: %CPPHA-7-START:cpp_ha: CPP 0 running init
*Dec 12 09:29:11.645: %CPPHA-7-READY:cpp_ha: CPP 0 loading and initialization complete
*Dec 12 09:29:11.711: %IOSXE-6-PLATFORM:cpp_cp:
Process CPP_PFILTER_EA_EVENT__API_CALL__REGISTER
*Dec 12 09:29:16.280:
%IOSXE_MGMTVRF-6-CREATE_SUCCESS_INFO:
Management vrf Mgmt-intf created with ID 1, ipv4 table-id 0x1, ipv6 table-id 0x1E000001
*Dec 12 09:29:16.330:
%LINEPROTO-5-UPDOWN: Line protocol on Interface Lsmpi0, changed state to up
*Dec 12 09:29:16.330:
%LINEPROTO-5-UPDOWN: Line protocol on Interface EOBC0, changed state to up
*Dec 12 09:29:16.330:
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Dec 12 09:29:16.330:
%LINEPROTO-5-UPDOWN: Line protocol on Interface LIIN0, changed state to up
*Dec 12 09:29:17.521: %SYS-5-LOG_CONFIG_CHANGE: Buffer logging disabled
*Dec 12 09:29:18.867: %SYS-5-CONFIG_I: Configured from memory by console
*Dec 12 09:29:18.870:
%IOSXE_OIR-6-REMSPA: SPA removed from subslot 0/0, interfaces disabled
*Dec 12 09:29:18.870:
%IOSXE_OIR-6-REMSPA: SPA removed from subslot 0/1, interfaces disabled
*Dec 12 09:29:18.871:
%IOSXE_OIR-6-REMSPA: SPA removed from subslot 0/2, interfaces disabled
*Dec 12 09:29:18.873:
%SPA_OIR-6-OFFLINECARD: SPA (ISR4451-X-4x1GE) offline in subslot 0/0
*Dec 12 09:29:18.874: %SPA_OIR-6-OFFLINECARD: SPA (NIM-VA-B) offline in subslot 0/1
*Dec 12 09:29:18.874: %SPA_OIR-6-OFFLINECARD: SPA (NIM-VAB-A) offline in subslot 0/2
*Dec 12 09:29:18.876: %IOSXE_OIR-6-INSCARD: Card (fp) inserted in slot F0

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 37
Installing the Software
Upgrading the Firmware on xDSL NIMs

*Dec 12 09:29:18.876: %IOSXE_OIR-6-ONLINECARD: Card (fp) online in slot F0

*Dec 12 09:29:18.882: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/0
*Dec 12 09:29:18.884: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/1
*Dec 12 09:29:18.884: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/2
*Dec 12 09:29:18.935: %SYS-5-RESTART: System restarted --
Cisco IOS Software, ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.5(1)S,
RELEASE SOFTWARE (fc5)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Thu 20-Nov-14 18:28 by mcpre
*Dec 12 09:29:18.895: %SPA-3-ENVMON_NOT_MONITORED:iomd: Environmental monitoring
is not enabled for ISR4451-X-4x1GE[0/0]
*Dec 12 09:29:19.878: %LINK-5-CHANGED: Interface GigabitEthernet0,

changed state to administratively down

*Dec 12 09:29:22.419: %SPA_OIR-6-ONLINECARD: SPA (ISR4451-X-4x1GE) online in subslot 0/0
*Dec 12 09:29:22.610: %SYS-6-BOOTTIME: Time taken to reboot after reload = 194 seconds
*Dec 12 09:29:24.354: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/0,
changed state to down
*Dec 12 09:29:24.415: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/2,
changed state to down
*Dec 12 09:29:24.417: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/3,
changed state to down
*Dec 12 09:29:30.919: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/0,
changed state to up
*Dec 12 09:29:30.925: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/2,
changed state to up
*Dec 12 09:29:30.936: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/3,
changed state to up
*Dec 12 09:29:31.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet0/0/0, changed state to up
*Dec 12 09:29:31.930: %LINEPROTO-5-UPDOWN: Line protocol on
Interface GigabitEthernet0/0/2, changed state to up
*Dec 12 09:29:31.936: %LINEPROTO-5-UPDOWN: Line protocol on
Interface GigabitEthernet0/0/3, changed state to up
*Dec 12 09:29:34.147: %SSH-5-ENABLED: SSH 1.99 has been enabled
*Dec 12 09:30:29.152: %SPA_OIR-6-ONLINECARD: SPA (NIM-VA-B) online in subslot 0/1
*Dec 12 09:30:29.470: %SPA_OIR-6-ONLINECARD: SPA (NIM-VAB-A) online in subslot 0/2
*Dec 12 09:30:31.152: %LINK-3-UPDOWN: Interface Ethernet0/1/0, changed state to down
*Dec 12 09:30:31.152: %LINK-3-UPDOWN: Interface ATM0/1/0, changed state to down
*Dec 12 09:30:31.470: %LINK-3-UPDOWN: Interface Ethernet0/2/0, changed state to down
*Dec 12 09:30:31.470: %LINK-3-UPDOWN: Interface ATM0/2/0, changed state to down
*Dec 12 09:31:03.074: %CONTROLLER-5-UPDOWN: Controller VDSL 0/2/0, changed state to up
*Dec 12 09:31:05.075: %LINK-3-UPDOWN: Interface Ethernet0/2/0, changed state to up
*Dec 12 09:31:06.076: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/2/0,
changed state to up
*Dec 12 09:31:12.559: %CONTROLLER-5-UPDOWN: Controller VDSL 0/1/0, changed state to up
*Dec 12 09:31:20.188: %LINK-3-UPDOWN: Interface ATM0/1/0, changed state to up
*Dec 12 09:31:21.188: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/1/0,
changed state to up
Router>
Router>en
Password:
Router#
Router#show controller vdsl 0/2/0
Controller VDSL 0/2/0 is UP

Daemon Status: UP

XTU-R (DS) XTU-C (US)

Chip Vendor ID: 'BDCM' 'BDCM'
Chip Vendor Specific: 0x0000 0xA41B
Chip Vendor Country: 0xB500 0xB500
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x4602 0x0000
Modem Vendor Country: 0xB500 0x0000
Serial Number Near: FOC18426DQ8 4451-X/K15.5(1)S
Serial Number Far:
Modem Version Near: 15.5(1)S
Modem Version Far: 0xa41b

Modem Status(L1): TC Sync (Showtime!)

DSL Config Mode: VDSL2

Cisco 4000 Series ISRs Software Configuration Guide

38 OL-29328-03
Installing the Software
Upgrading the Firmware on xDSL NIMs

Trained Mode(L1): G.993.2 (VDSL2) Profile 30a

TC Mode: PTM
Selftest Result: 0x00
DELT configuration: disabled
DELT state: not running

Failed full inits: 0

Short inits: 0
Failed short inits: 0

Modem FW Version: 4.14L.04

Modem PHY Version: A2pv6F039h.d24o_rc1

Line 1:

XTU-R (DS) XTU-C (US)

Trellis: ON ON
SRA: disabled disabled
SRA count: 0 0
Bit swap: enabled enabled
Bit swap count: 9 0
Profile 30a: enabled
Line Attenuation: 3.5 dB 0.0 dB
Signal Attenuation: 0.0 dB 0.0 dB
Noise Margin: 30.9 dB 12.4 dB
Attainable Rate: 200000 kbits/s 121186 kbits/s
Actual Power: 13.3 dBm 7.2 dBm
Per Band Status: D1 D2 D3 U0 U1 U2 U3
Line Attenuation(dB): 0.9 1.5 5.5 N/A 0.1 0.9 3.8
Signal Attenuation(dB): 0.8 1.5 5.5 N/A 0.0 0.2 3.2
Noise Margin(dB): 31.1 31.0 30.9 N/A 12.3 12.4 12.5
Total FECC: 0 0
Total ES: 0 0
Total SES: 0 0
Total LOSS: 0 0
Total UAS: 51 51
Total LPRS: 0 0
Total LOFS: 0 0
Total LOLS: 0 0

DS Channel1 DS Channel0 US Channel1 US Channel0

Speed (kbps): NA 100014 NA 100014
SRA Previous Speed: NA 0 NA 0
Previous Speed: NA 0 NA 0
Reed-Solomon EC: NA 0 NA 0
CRC Errors: NA 0 NA 0
Header Errors: NA 0 NA 0
Interleave (ms): NA 9.00 NA 0.00
Actual INP: NA 4.00 NA 0.00

Training Log : Stopped

Training Log Filename : flash:vdsllog.bin

Router#
Router#

Router#copy bootflash:isr4400-firmware_nim_xdsl.2014-11-17_11.05_39n.SSA.pkg
bootflash:mydir/
Destination filename [mydir/isr4400-firmware_nim_xdsl.2014-11-17_11.05_39n.SSA.pkg]?
Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
6640604 bytes copied in 1.365 secs (4864911 bytes/sec)
Router#

Router#request platform software package install rp 0 file

bootflash:mydir/isr4400-firmware_nim_xdsl.2014-11-17_11.05_39n.SSA.pkg
--- Starting local lock acquisition on R0 ---
Finished local lock acquisition on R0

--- Starting file path checking ---

Finished file path checking

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 39
Installing the Software
Upgrading the Firmware on xDSL NIMs

--- Starting image file verification ---

Checking image file names
Locating image files and validating name syntax
Found isr4400-firmware_nim_xdsl.2014-11-17_11.05_39n.SSA.pkg
Verifying image file locations
Inspecting image file types
Processing image file constraints
Creating candidate provisioning file
Finished image file verification

--- Starting candidate package set construction ---

Verifying existing software set
Processing candidate provisioning file
Constructing working set for candidate package set
Constructing working set for running package set
Checking command output
Constructing merge of running and candidate packages
Checking if resulting candidate package set would be complete
Finished candidate package set construction

--- Starting ISSU compatiblity verficiation ---

Verifying image type compatibility
Checking IPC compatibility with running software
Checking candidate package set infrastructure compatibility
Checking infrastructure compatibility with running software
Checking package specific compatibility
Finished ISSU compatiblity verficiation

--- Starting impact testing ---

Checking operational impact of change
Finished impact testing

--- Starting list of software package changes ---

Old files list:
Removed isr4400-firmware_nim_xdsl.03.14.00.S.155-1.S-std.SPA.pkg
New files list:
Added isr4400-firmware_nim_xdsl.2014-11-17_11.05_39n.SSA.pkg
Finished list of software package changes

--- Starting commit of software changes ---

Updating provisioning rollback files
Creating pending provisioning file
Committing provisioning file
Finished commit of software changes

--- Starting analysis of software changes ---

Finished analysis of software changes

--- Starting update running software ---

Blocking peer synchronization of operating information
Creating the command set placeholder directory
Finding latest command set
Finding latest command shortlist lookup file
Finding latest command shortlist file
Assembling CLI output libraries
Assembling CLI input libraries
Skipping soft links for firmware upgrade
Skipping soft links for firmware upgrade
Assembling Dynamic configuration files
Applying interim IPC and database definitions
rsync: getaddrinfo: cc2-0 873: Name or service not known rsync error:
error in socket IO (code 10) at /auto/mcpbuilds19/
release/03.14.00.S/BLD-V03_14_00_S_FC5/contrib/rsync/clientserver.c(104) [sender=2.6.9]
rsync: getaddrinfo: cc2-0 873: Name or service not known rsync error:
error in socket IO (code 10) at /auto/mcpbuilds19/
release/03.14.00.S/BLD-V03_14_00_S_FC5/contrib/rsync/clientserver.c(104) [sender=2.6.9]
rsync: getaddrinfo: cc2-0 873: Name or service not known rsync error:
error in socket IO (code 10) at /auto/mcpbuilds19
/release/03.14.00.S/BLD-V03_14_00_S_FC5/contrib/rsync/clientserver.c(104) [sender=2.6.9]
Replacing running software
Replacing CLI software
Restarting software

Cisco 4000 Series ISRs Software Configuration Guide

40 OL-29328-03
Installing the Software
Upgrading the Firmware on xDSL NIMs

Applying final IPC and database definitions

rsync: getaddrinfo: cc2-0 873: Name or service not known rsync error:
error in socket IO (code 10) at /auto/mcpbuilds19/
release/03.14.00.S/BLD-V03_14_00_S_FC5/contrib/rsync/clientserver.c(104) [sender=2.6.9]
Generating software version information
Notifying running software of updates
Unblocking peer synchronization of operating information
Unmounting old packages
Cleaning temporary installation files
Finished update running software

SUCCESS: Finished installing software.

Router#
Router#show platform software subslot 0/2 module firmware
Avg Load info
-------------------------------------------
1.83 1.78 1.44 3/45 607

Kernel distribution info

-------------------------------------------
Linux version 3.4.11-rt19 (sapanwar@blr-atg-001) (gcc version 4.6.2
(Buildroot 2011.11) ) #3 SMP PREEMPT Fri Nov 7 09:26:19 IST 2014

Module firmware versions

-------------------------------------------
Modem Fw Version: 4.14L.04
Modem Phy Version: A2pv6F039h.d24o_rc1

Boot Loader: Secondry

-------------------------------------------
Version: 1.1

Modem Up time
-------------------------------------------
0D 0H 25M 38S

Router#

Router#hw-module subslot 0/2 reload

Proceed with reload of module? [confirm]
Router#
*Dec 12 09:55:59.645: %IOSXE_OIR-6-SOFT_RELOADSPA: SPA(NIM-VAB-A)
reloaded on subslot 0/2
*Dec 12 09:55:59.646: %SPA_OIR-6-OFFLINECARD: SPA (NIM-VAB-A) offline in subslot 0/2
*Dec 12 09:55:59.647: %CONTROLLER-5-UPDOWN: Controller VDSL 0/2/0, changed state to down
*Dec 12 09:57:22.514: new extended attributes received from iomd(slot 0 bay 2 board 0)
*Dec 12 09:57:22.514: %IOSXE_OIR-6-SOFT_RELOADSPA: SPA(NIM-VAB-A)
reloaded on subslot 0/2
*Dec 12 09:57:22.515: %SPA_OIR-6-OFFLINECARD: SPA (NIM-VAB-A) offline in subslot 0/2
Router#
Router#
*Dec 12 09:58:35.471: %SPA_OIR-6-ONLINECARD: SPA (NIM-VAB-A) online in subslot 0/2
*Dec 12 09:58:37.470: %LINK-3-UPDOWN: Interface Ethernet0/2/0, changed state to down
*Dec 12 09:58:37.470: %LINK-3-UPDOWN: Interface ATM0/2/0, changed state to down
Router#

Router#show platform software subslot 0/2 module firmware

Avg Load info
-------------------------------------------
0.84 0.23 0.08 1/45 598

Kernel distribution info

-------------------------------------------
Linux version 3.4.11-rt19 (sapanwar@blr-atg-001) (gcc version 4.6.2 (Buildroot 2011.11) )
#6 SMP PREEMPT Mon Nov 17 10:51:41 IST 2014

Module firmware versions

-------------------------------------------
Modem Fw Version: 4.14L.04
Modem Phy Version: A2pv6F039n.d24o_rc1

Boot Loader: Secondry

-------------------------------------------

Cisco 4000 Series ISRs Software Configuration Guide

OL-29328-03 41
Installing the Software
Upgrading the Firmware on xDSL NIMs

Version: 1.1

Modem Up time
-------------------------------------------
0D 0H 0M 42S

Router#

Cisco 4000 Series ISRs Software Configuration Guide

42 OL-29328-03

Zorin OS Administration and User Guide: Definitive Reference for Developers and Engineers
From Everand
Zorin OS Administration and User Guide: Definitive Reference for Developers and Engineers
Richard Johnson
No ratings yet
TABELA DE PRODUTOS E SERVIÇOS INFORMATICA 13dez2021
No ratings yet
TABELA DE PRODUTOS E SERVIÇOS INFORMATICA 13dez2021
4 pages
Chalk Production Processe
No ratings yet
Chalk Production Processe
17 pages
READING
No ratings yet
READING
1 page
DFSDFSDFSDFSD SDF SDFSDF DSF SDF SD FS DF DSF SD F DSF SD FDS
No ratings yet
DFSDFSDFSDFSD SDF SDFSDF DSF SDF SD FS DF DSF SD F DSF SD FDS
1 page
04 Laboratory Exercise 1
No ratings yet
04 Laboratory Exercise 1
2 pages
Immediate Download Business Driven Information Systems Fifth Edition. Edition Baltzan - Ebook PDF Ebooks 2024
100% (1)
Immediate Download Business Driven Information Systems Fifth Edition. Edition Baltzan - Ebook PDF Ebooks 2024
62 pages
AGS Services For SAP MaxAttention
No ratings yet
AGS Services For SAP MaxAttention
41 pages
AML For Cross Border Payment
No ratings yet
AML For Cross Border Payment
21 pages
Buxin
No ratings yet
Buxin
2 pages
Software Assignment Final
No ratings yet
Software Assignment Final
9 pages
Case Study 9
No ratings yet
Case Study 9
9 pages
Finscan Checklist
No ratings yet
Finscan Checklist
6 pages
Meridium APM Asset Strategy Management V3.6.0.0.0
No ratings yet
Meridium APM Asset Strategy Management V3.6.0.0.0
469 pages
PM - Case Study 2 - New
No ratings yet
PM - Case Study 2 - New
5 pages
CSIII - Computer Fundamentals
No ratings yet
CSIII - Computer Fundamentals
5 pages
Developer Portal User Guide
No ratings yet
Developer Portal User Guide
232 pages
Mod 5
No ratings yet
Mod 5
26 pages
Fortigate Infrastructure: High Availability (Ha)
No ratings yet
Fortigate Infrastructure: High Availability (Ha)
49 pages
Free Open Source Linux OS For Data Recovery & Data Rescue Bilingual Version Ultimate
From Everand
Free Open Source Linux OS For Data Recovery & Data Rescue Bilingual Version Ultimate
Cyber Jannah Sakura
No ratings yet
SE Question Bank
No ratings yet
SE Question Bank
8 pages
Isr4400 SW Config Xe 17
No ratings yet
Isr4400 SW Config Xe 17
606 pages
Aec514 Lecture 1
No ratings yet
Aec514 Lecture 1
33 pages
TX Vending Machine Presentation1
No ratings yet
TX Vending Machine Presentation1
37 pages
CCNA 200-301 Official Cert Guide, Volume 2-229
No ratings yet
CCNA 200-301 Official Cert Guide, Volume 2-229
3 pages
Final Assesment - MGT7101 PBS21101107 (8.8.2022) - Final
No ratings yet
Final Assesment - MGT7101 PBS21101107 (8.8.2022) - Final
10 pages
Manish+Lakra+ +React+Native
No ratings yet
Manish+Lakra+ +React+Native
2 pages
PCI Requirements On Implementing Key Blocks - Migration Phases and Key Management Solutions
No ratings yet
PCI Requirements On Implementing Key Blocks - Migration Phases and Key Management Solutions
5 pages
#Rachit Shah Resume
No ratings yet
#Rachit Shah Resume
2 pages
What Is Scrum - An Introduction To The Scrum Framework
No ratings yet
What Is Scrum - An Introduction To The Scrum Framework
20 pages
International Business Module 1
No ratings yet
International Business Module 1
5 pages
Linux - a Secure Personal Computer for Beginners. Second Edition
From Everand
Linux - a Secure Personal Computer for Beginners. Second Edition
Mark Emerson
No ratings yet
Archana G Servicenow Admin: Incident Management, CMDB, Asset Etc. Actions, UI Policies, Client Scripts Etc.)
No ratings yet
Archana G Servicenow Admin: Incident Management, CMDB, Asset Etc. Actions, UI Policies, Client Scripts Etc.)
4 pages
Sysimgmgmt Install
No ratings yet
Sysimgmgmt Install
22 pages
CH 5
No ratings yet
CH 5
37 pages
Mulesoft Course & Exam Catalog: Training Delivery Methods
No ratings yet
Mulesoft Course & Exam Catalog: Training Delivery Methods
7 pages
CH 2
No ratings yet
CH 2
23 pages
ICND110S04 5 Managing Cisco Devices
No ratings yet
ICND110S04 5 Managing Cisco Devices
29 pages
Wave Management
No ratings yet
Wave Management
9 pages
Module 1 - Introduction To E-Commerce
No ratings yet
Module 1 - Introduction To E-Commerce
8 pages
Airbnb Report
No ratings yet
Airbnb Report
10 pages
Introduction To Routers
No ratings yet
Introduction To Routers
7 pages
Day 5
No ratings yet
Day 5
25 pages
Chapter 2-Final
No ratings yet
Chapter 2-Final
21 pages
Asr1000 Software Config Guide
No ratings yet
Asr1000 Software Config Guide
660 pages
Coma Dos
No ratings yet
Coma Dos
1 page
Linux for Beginners: Linux Command Line, Linux Programming and Linux Operating System
From Everand
Linux for Beginners: Linux Command Line, Linux Programming and Linux Operating System
Steve Will
4.5/5 (3)
748ASD
No ratings yet
748ASD
2 pages
Class IX I.T. Term-I
No ratings yet
Class IX I.T. Term-I
4 pages
Cisco Router Rommon
No ratings yet
Cisco Router Rommon
10 pages
SW Upgrade Highendrouters 23233
No ratings yet
SW Upgrade Highendrouters 23233
11 pages
C04 (En) (Managing Cisco IOS Software)
No ratings yet
C04 (En) (Managing Cisco IOS Software)
24 pages
Ch14 - Managing Cisco IOS Software
No ratings yet
Ch14 - Managing Cisco IOS Software
22 pages
Table Spaces
No ratings yet
Table Spaces
2 pages
Appendix Dconfigreg
No ratings yet
Appendix Dconfigreg
6 pages
Chapter 6 - Routers and Basic Configuration
No ratings yet
Chapter 6 - Routers and Basic Configuration
92 pages
Talking About Your Family: Questions Your Teacher Will Ask
No ratings yet
Talking About Your Family: Questions Your Teacher Will Ask
1 page
Isr 4400 SWCFG
No ratings yet
Isr 4400 SWCFG
336 pages
Arch Linux: Fast and Light!
From Everand
Arch Linux: Fast and Light!
Frank Cheung
3/5 (2)
MIS &amp Decision Making
No ratings yet
MIS &amp Decision Making
25 pages
Controllogix /studio 5000: Studio 5000 Logix Designer Level 4: Function Block Programming Course Description
No ratings yet
Controllogix /studio 5000: Studio 5000 Logix Designer Level 4: Function Block Programming Course Description
2 pages
Taller Cisco 1
No ratings yet
Taller Cisco 1
8 pages
Cnap - 2 - 05 - Routers and Routing Basics
No ratings yet
Cnap - 2 - 05 - Routers and Routing Basics
4 pages
CCNA 2 v3.1 Module 2 Introduction To Routers: © 2004, Cisco Systems, Inc. All Rights Reserved
No ratings yet
CCNA 2 v3.1 Module 2 Introduction To Routers: © 2004, Cisco Systems, Inc. All Rights Reserved
22 pages
Gmsi10 Um013 - en P
No ratings yet
Gmsi10 Um013 - en P
216 pages
Laboratorio 2@
No ratings yet
Laboratorio 2@
5 pages
Software Configuration Guide For The Cisco ISR 4400 Series
No ratings yet
Software Configuration Guide For The Cisco ISR 4400 Series
236 pages
6.3.2.7 Lab - Exploring Router Physical Characteristics PDF
No ratings yet
6.3.2.7 Lab - Exploring Router Physical Characteristics PDF
7 pages
Ccna 2 Router and Routing Basics: 5-Managing Cisco IOS Software
No ratings yet
Ccna 2 Router and Routing Basics: 5-Managing Cisco IOS Software
33 pages
Basic Config
No ratings yet
Basic Config
52 pages
Nexus5000config 00
No ratings yet
Nexus5000config 00
5 pages
Cisco Isr4400 Series Software Installation Guide
100% (1)
Cisco Isr4400 Series Software Installation Guide
304 pages
Introduction To Routers: CCNA 2 Version 3.0 Rick Graziani Cabrillo College
No ratings yet
Introduction To Routers: CCNA 2 Version 3.0 Rick Graziani Cabrillo College
25 pages
Introduction To Cisco Ios: Prepared By, Prof - Dhanalakshmi IT Dept, Scet
No ratings yet
Introduction To Cisco Ios: Prepared By, Prof - Dhanalakshmi IT Dept, Scet
90 pages
Chapter 5
No ratings yet
Chapter 5
22 pages
Ch. 5 - Managing Cisco IOS Software: CCNA 2 Version 3.0 Rick Graziani Cabrillo College
No ratings yet
Ch. 5 - Managing Cisco IOS Software: CCNA 2 Version 3.0 Rick Graziani Cabrillo College
45 pages
Cisco 4000 Series ISRs Software Configuration Guide
No ratings yet
Cisco 4000 Series ISRs Software Configuration Guide
330 pages
Fundamentals Xe 3se 3850 CR Book
No ratings yet
Fundamentals Xe 3se 3850 CR Book
212 pages
Use of The Configuration Register On All Cisco Routers
No ratings yet
Use of The Configuration Register On All Cisco Routers
7 pages
CCNA 2 v3.1 Module 5 Managing Cisco IOS Software: © 2004, Cisco Systems, Inc. All Rights Reserved
No ratings yet
CCNA 2 v3.1 Module 5 Managing Cisco IOS Software: © 2004, Cisco Systems, Inc. All Rights Reserved
21 pages
CCNA2 Chapter1
No ratings yet
CCNA2 Chapter1
100 pages
Resumen Procedimiento de Actualización Plataforma Cisco 7600
No ratings yet
Resumen Procedimiento de Actualización Plataforma Cisco 7600
5 pages
Upgrade 2900
No ratings yet
Upgrade 2900
26 pages
Installing or Upgrading Cisco IOS Software: Before You Begin
No ratings yet
Installing or Upgrading Cisco IOS Software: Before You Begin
6 pages
Router Basics
No ratings yet
Router Basics
18 pages
BASIC Commands of Routers
No ratings yet
BASIC Commands of Routers
17 pages
Workshop 9 - Cisco Router Configuration
No ratings yet
Workshop 9 - Cisco Router Configuration
10 pages
6.3.1.9 Lab - Exploring Router Physical Characteristics
0% (1)
6.3.1.9 Lab - Exploring Router Physical Characteristics
8 pages
The Purpose and Use of The Configuration Register On All Cisco Routers................................................... 1
No ratings yet
The Purpose and Use of The Configuration Register On All Cisco Routers................................................... 1
8 pages
CCNAv3.3 205
No ratings yet
CCNAv3.3 205
35 pages
Cisco ISO and Boot Process PDF
No ratings yet
Cisco ISO and Boot Process PDF
10 pages
Chpt.5.Supplemental Cisco - ppt.2
No ratings yet
Chpt.5.Supplemental Cisco - ppt.2
52 pages
Ios Upgrade
No ratings yet
Ios Upgrade
17 pages
Cisco® Router Configuration & Troubleshooting - 3 - Initial Router Setup
No ratings yet
Cisco® Router Configuration & Troubleshooting - 3 - Initial Router Setup
10 pages
Using The ROM
No ratings yet
Using The ROM
10 pages
Ios Router Commands
No ratings yet
Ios Router Commands
16 pages
Ch.2 - Introduction To Routers: CCNA 2 Version 3.0
No ratings yet
Ch.2 - Introduction To Routers: CCNA 2 Version 3.0
25 pages
WXES2106 Network Technology Semester 1 2004/2005: Routers
No ratings yet
WXES2106 Network Technology Semester 1 2004/2005: Routers
34 pages
Actualizacion de IOS (6500)
No ratings yet
Actualizacion de IOS (6500)
21 pages