Hino 700 Service Brake

SERVICE BRAKE BR02–1
SERVICE BRAKE
BR02
BR02-001
AIR DRYER ...............................................BR02-3 PROTECTION VALVE (WITH 4-WAY

DATA AND SPECIFICATIONS........................ BR02-3 PROTECTION VALVE) ............................BR02-31
DESCRIPTION ................................................ BR02-3 DATA AND SPECIFICATIONS...................... BR02-31
COMPONENT LOCATOR ............................... BR02-4 DESCRIPTION .............................................. BR02-31
OVERHAUL ..................................................... BR02-5 COMPONENT LOCATOR ............................. BR02-32
INSPECTION AND REPAIR ............................ BR02-7 OVERHAUL ................................................... BR02-33
ADJUSTMENT............................................... BR02-33
CHECK VALVE..........................................BR02-8 INSPECTION AND REPAIR .......................... BR02-35
DATA AND SPECIFICATIONS........................ BR02-8
DESCRIPTION ................................................ BR02-8 QUICK RELEASE VALVE .......................BR02-36
COMPONENT LOCATOR ............................... BR02-9 DATA AND SPECIFICATION ........................ BR02-36
INSPECTION AND REPAIR ............................ BR02-9 DESCRIPTION .............................................. BR02-36
cardiagn.com
COMPONENT LOCATOR ............................. BR02-37
DOUBLE CHECK VALVE .......................BR02-10 OVERHAUL ................................................... BR02-38
DATA AND SPECIFICATION ........................ BR02-10 INSPECTION AND REPAIR .......................... BR02-38
DESCRIPTION .............................................. BR02-10
COMPONENT LOCATOR ............................. BR02-11 LOAD SENSING VALVE .........................BR02-39
OVERHAUL ................................................... BR02-12 DATA AND SPECIFICATION ........................ BR02-39
INSPECTION AND REPAIR .......................... BR02-12 DESCRIPTION .............................................. BR02-40
COMPONENT LOCATOR ............................. BR02-42
SAFETY VALVE ......................................BR02-13 OVERHAUL ................................................... BR02-44
DATA AND SPECIFICATIONS...................... BR02-13 ADJUSTMENT............................................... BR02-47
DESCRIPTION .............................................. BR02-13 INSPECTION AND REPAIR .......................... BR02-48
INSPECTION AND REPAIR .......................... BR02-13
SPRING BRAKE CONTROL VALVE
BRAKE VALVE........................................BR02-14 (TYPE-A) .................................................BR02-50
DATA AND SPECIFICATION ........................ BR02-14 DATA AND SPECIFICATIONS...................... BR02-50
DESCRIPTION .............................................. BR02-14 DESCRIPTION .............................................. BR02-50
COMPONENT LOCATOR ............................. BR02-15 COMPONENT LOCATOR ............................. BR02-51
OVERHAUL ................................................... BR02-17 OVERHAUL ................................................... BR02-52
INSPECTION AND REPAIR .......................... BR02-23 INSPECTION AND REPAIR .......................... BR02-54
PROTECTION VALVE (TYPE-A) ............BR02-25 SPRING BRAKE CONTROL VALVE

DATA AND SPECIFICATIONS...................... BR02-25 (TYPE-B) .................................................BR02-55
DESCRIPTION .............................................. BR02-25 DATA AND SPECIFICATIONS...................... BR02-55
COMPONENT LOCATOR ............................. BR02-26 DESCRIPTION .............................................. BR02-55
OVERHAUL ................................................... BR02-27 COMPONENT LOCATOR ............................. BR02-56
INSPECTION AND REPAIR .......................... BR02-27 OVERHAUL ................................................... BR02-57
PROTECTION VALVE (TYPE-B) ............BR02-28
DATA AND SPECIFICATIONS...................... BR02-28 RELAY VALVE (TYPE-A) ........................BR02-60
DESCRIPTION .............................................. BR02-28 DATA AND SPECIFICATIONS...................... BR02-60
COMPONENT LOCATOR ............................. BR02-29 DESCRIPTION .............................................. BR02-60
OVERHAUL ................................................... BR02-30 COMPONENT LOCATOR ............................. BR02-61
INSPECTION AND REPAIR .......................... BR02-30 OVERHAUL ................................................... BR02-62
BR02–2 SERVICE BRAKE
RELAY VALVE (TYPE-B)........................ BR02-64 DESCRIPTION ...............................................BR02-95

DATA AND SPECIFICATIONS ......................BR02-64 COMPONENT LOCATOR..............................BR02-96
DESCRIPTION...............................................BR02-64
BR 02
OVERHAUL....................................................BR02-97
COMPONENT LOCATOR..............................BR02-65 INSPECTION AND REPAIR ..........................BR02-98
OVERHAUL....................................................BR02-66
INSPECTION AND REPAIR ..........................BR02-66 SPRING BRAKE CHAMBER
(MAKER: WABCO) ................................. BR02-99
CUT VALVE............................................. BR02-67 DATA AND SPECIFICATION.........................BR02-99
DATA AND SPECIFICATION.........................BR02-67 DESCRIPTION ...............................................BR02-99
DESCRIPTION...............................................BR02-67 COMPONENT LOCATOR............................BR02-100
COMPONENT LOCATOR..............................BR02-68 SPECIAL TOOL ...........................................BR02-100
OVERHAUL....................................................BR02-68 OVERHAUL..................................................BR02-101
INSPECTION AND REPAIR ..........................BR02-69 INSPECTION AND REPAIR ........................BR02-107
REDUCING VALVE (TYPE-A) ................ BR02-70 TRAILER HAND BRAKE

DATA AND SPECIFICATIONS ......................BR02-70 CONTROL VALVE.................................BR02-108
DESCRIPTION...............................................BR02-70 DATA AND SPECIFICATION.......................BR02-108
COMPONENT LOCATOR..............................BR02-71 DESCRIPTION .............................................BR02-108
OVERHAUL....................................................BR02-72 COMPONENT LOCATOR............................BR02-109
INSPECTION AND REPAIR ..........................BR02-72 OVERHAUL..................................................BR02-110
cardiagn.com
INSPECTION AND REPAIR ........................BR02-112
REDUCING VALVE (TYPE-B) ................ BR02-73
DATA AND SPECIFICATIONS ......................BR02-73 WHEEL BRAKE
DESCRIPTION...............................................BR02-73 (TYPE: S-CAM BRAKE) .......................BR02-114
COMPONENT LOCATOR..............................BR02-74
DATA AND SPECIFICATIONS ....................BR02-114
OVERHAUL....................................................BR02-75
DESCRIPTION .............................................BR02-115
INSPECTION AND REPAIR ..........................BR02-75
SPECIAL TOOL ...........................................BR02-121
COMPONENT LOCATOR............................BR02-122
BRAKE CHAMBER ................................ BR02-76 OVERHAUL..................................................BR02-132
DATA AND SPECIFICATION.........................BR02-76 ADJUSTMENT .............................................BR02-141
DESCRIPTION...............................................BR02-76 INSPECTION AND REPAIR ........................BR02-143
OVERHAUL....................................................BR02-78 WHEEL BRAKE
(TYPE: WEDGE BRAKE) .....................BR02-145
BRAKE CHAMBER DESCRIPTION .............................................BR02-145
(MAKER: WABCO) ................................. BR02-80 SPECIAL TOOL ...........................................BR02-147
DATA AND SPECIFICATION.........................BR02-80 COMPONENT LOCATOR............................BR02-148
DESCRIPTION...............................................BR02-80 OVERHAUL..................................................BR02-150
COMPONENT LOCATOR..............................BR02-81 ADJUSTMENT .............................................BR02-156
SPECIAL TOOL .............................................BR02-81 INSPECTION AND REPAIR ........................BR02-158
OVERHAUL....................................................BR02-82
INSPECTION AND REPAIR ..........................BR02-86 EXPANDER ...........................................BR02-159
DESCRIPTION .............................................BR02-159
SPRING BRAKE CHAMBER ................. BR02-87 SPECIAL TOOL ...........................................BR02-160
DATA AND SPECIFICATION.........................BR02-87 COMPONENT LOCATOR............................BR02-161
DESCRIPTION...............................................BR02-88 OVERHAUL..................................................BR02-162
SPECIAL TOOL .............................................BR02-89 INSPECTION AND REPAIR ........................BR02-165
OVERHAUL....................................................BR02-90 PRESSURE REGULATOR ...................BR02-167
DESCRIPTION .............................................BR02-167
SPRING BRAKE CHAMBER COMPONENT LOCATOR............................BR02-168
(MAKER: NABCO) ................................. BR02-95 OVERHAUL..................................................BR02-169
DATA AND SPECIFICATION.........................BR02-95 INSPECTION AND REPAIR ........................BR02-170
AIR DRYER
DATA AND SPECIFICATIONS
EN0680202I200001
Type Purge tank, desiccant, auto-purge valve.

Air and Water discharging time (Reclamation cycle) Approx. 50 sec.
DESCRIPTION
EN0680202C100001
SHTS068020200001 cardiagn.com
1 Chamber (Purge tank) 14 Plug
2 Case cover 15 Pressure regulator
3 Check valve 16 Adjusting screw
4 Spring 17 Piston
5 Body 18 Piston spring
6 Desiccant case 19 Heater (If so equipped)
7 Filter A Inlet (From air compressor)
8 Desiccant B Orifice
9 Oil separator filter C Outlet (Dried air to air tank)
10 Valve body D Purged air
11 Valve spring E Dehumidification
12 Piston F Reclamation
13 Purge valve
COMPONENT LOCATOR
EN0680202D100001
cardiagn.com
SHTS068020200002
1 O-ring 18 Desiccant
2 Cover 19 Desiccant case
3 Piston 20 Oil separator filter
4 Valve spring 21 Body
5 Valve body 22 Valve stopper
6 Purge valve 23 Governor valve
7 Silencer case 24 Piston assembly
8 Silencer plate 25 Exhaust stem spring
9 Silencer 26 Exhaust stem
10 Retainer ring 27 Pressure regulator assembly
11 Exhaust cover 28 Valve seat
12 Chamber 29 Plate
13 Check valve 30 Heater
14 Case cover 31 Thermostat
15 Set spring 32 Plug
16 Filter plate 33 Elbow connector
17 Filter 34 Tube
Tightening torque Unit: N⋅m {kgf⋅cm, lbf⋅ft}

A 3.9-6.9 {40-70, 2.9-5.0} D 6.9-7.8 {71-79, 5.1-5.7}
B 3.9-6.9 {40-70, 2.9-5.0} E 17.7-27.5 {181-280, 14-20}
C 4.9-5.9 {50-60, 3.7-4.3}
OVERHAUL
EN0680202H200001
IMPORTANT POINTS - ASSEMBLY
1. LUBRICATION
C (1) When assembling the air dryer, use new O-ring, gasket and seal.
(2) Apply grease (lithium base) to each sliding surface of the compo-
nent parts and O-ring groove.
A • A: O-ring
• B: Sliding surface
2. ASSEMBLY
A NOTICE
Before tighten the bolt with specified tightening torque, tap all
over the outer surface of the desiccant case with a plastic ham-
mer.
• C: Bolt
A
A
cardiagn.com
SHTS068020200003
IMPORTANT POINTS - MOUNTING
1. INSPECTION
(1) Operate the engine and raise the air pressure until the air dis-
charge from the purge valve, then stop the engine.
(The pressure reaches the valve opening pressure of the air pres-
sure regulator).
a. Check to see that there is no air leakage from the purge valve.
2. ADJUSTMENT
(1) Loosen the adjusting screw until the rod spring tension is
released, and start and idle the engine to charge the air for the air
tank.
SHTS068020200004
(2) Tighten the adjusting screw gradually till the air pressure gauge
cardiagn.com
indicate valve opening pressure shown below and the air starts to
discharge from purge valve.
Governor valve opening pressure:
960-1,000 kPa {9.8-10.2 kgf/cm2, 139.2-145.0 lbf/in.2}
(3) Tighten the adjusting screw lock nut.
SHTS068020200005
(4) Watch the air pressure gauge needle and see that it stops at the
valve closing pressure shown below.
Governor valve closing pressure:
860-900 kPa {8.8-9.2 kgf/cm2, 124.7-130.5 lbf/in.2}
SHTS068020200006
INSPECTION AND REPAIR

EN0680202H300001
Inspection Item Standard Limit Remedy Inspection Procedure
Check valve and valve — — Replace, Visual check

seat surface: if necessary.
Wear and damage
Valve body sliding surface — — Replace, Visual check

and purge valve seat sur- if necessary.
face:
Wear and damage
Piston sliding surface: — — Replace, Visual check

Wear and damage if necessary.
cardiagn.com
Purge valve seat surface: — — Replace, Visual check
Desiccant: — Discolored, Replace. Visual check

Contamination and deteri- more than 1/5
oration of the quantity.
CHECK VALVE
EN0680202I200002
Type Spring type

Valve opening pressure Outlet side pressure 14.7 kPa {0.15 kgf/cm2, 2.13 lbf/in.2}
DESCRIPTION
EN0680202C100002
cardiagn.com
SHTS068020200012
1 Valve body 5 Body cap

2 Conical spring A OUT
3 Valve seat B IN
4 O-ring
COMPONENT LOCATOR
EN0680202D100002
cardiagn.com
SHTS068020200013
1 Valve body 4 O-ring

2 Conical spring 5 Body cap
3 Valve seat

A 44.1-53.9 {450-550, 33-39}

EN0680202H300002
Unit: mm {in.}
Body cap: — — Replace, Visual check

Wear and any other dam- if necessary.
age
Conical spring: 17.5 {0.69} 16.5 {0.65} Replace. Measure and Visual check
Rust, damage and free
length
DOUBLE CHECK VALVE

DATA AND SPECIFICATION
EN0680202I200003
Type Piston type
DESCRIPTION
EN0680202C100003
cardiagn.com
SHTS068020200016
1 Valve body 5 Plug

2 Valve A Outlet
3 Guide B Inlet
4 Gasket
COMPONENT LOCATOR
EN0680202D100003
cardiagn.com
SHTS068020200017
1 Valve body 4 Gasket

2 Valve 5 Plug
3 Guide

A 34.3-44.1 {350-450, 25.3-32.5}
OVERHAUL
EN0680202H200002
IMPORTANT POINT - ASSEMBLY
1. LUBRICATION
(1) When assembling the double check valve, apply the ThreeBond:
TB-1101 or equivalent to the gasket.
NOTICE
Check to see that there is no air leakage from "A", when air is
charged from "B", and no air leakage from "B", when air is
charged from "A".
SHTS068020200018

EN0680202H300003
Valve and guide: — — Clean or replace, Visual check
cardiagn.com
Rust, wear and damage if necessary.
Valve body and plug: — — Clean or replace, Visual check

SAFETY VALVE
EN06802022600001
Type Spring type

Valve opening pressure 1,029-1,068 kPa {10.5-10.9 kgf/cm2, 149.2-154.9 lbf/in.2}
DESCRIPTION
EN0680202C100004
cardiagn.com
SHTS068020200021
1 Valve 5 Compression spring

2 Body A Exhaust
3 Nut B From air tank (Pressure air)
4 Bolt

EN0680202H300004
Unit: kPa {kgf/cm2, lbf/in.2}
Valve opening pressure 1,029-1,068 — Replace. Measure

{10.5-10.9,
149.2-154.9}
BRAKE VALVE
EN0680202I200004
Type Dual pistons and valves with a plunger type pedal
DESCRIPTION
EN0680202C100005
cardiagn.com
SHTS068020200022
1 Boot 16 Primary piston return spring

2 Plunger 17 Primary valve body
3 Brake valve cover 18 Primary feed valve
4 Retainer ring 19 Retainer
5 Guide ring 20 Primary feed valve return spring
6 Spring seat 21 Primary feed valve retainer
7 Sub spring 22 Secondary piston
8 Shim 23 Secondary piston return spring
9 Stem 24 Secondary valve body
10 Main spring 25 Secondary feed valve
11 Shim 26 Retainer
12 Guide ring 27 Secondary feed valve return spring
13 O-ring 28 Secondary feed valve retainer
14 Primary piston 29 C-ring
15 Guide 30 Exhaust port
COMPONENT LOCATOR
EN0680202D100004
cardiagn.com
SHTS068020200023
1 Stop lamp switch 10 Push rod

2 Bushing 11 Seal
3 Bracket 12 Clip
4 Buffer 13 Shaft
5 Pin 14 Pedal bracket
6 R-pin 15 Brake valve
7 Pedal pad 16 Connector
8 Brake pedal 17 Clutch master cylinder
9 Return spring

A 9.5-18.5 {97-188, 7.1-13.6} C 24.4-34.5 {249-351, 18-25}
B 18-31 {184-316, 14-22}
cardiagn.com
SHTS068020200024
1 Boot 16 Primary piston return spring

2 Plunger 17 Primary valve body
3 Brake valve cover 18 Primary feed valve
4 Retainer ring 19 Retainer
5 Guide ring 20 Primary feed valve return spring
6 Spring seat 21 Primary feed valve retainer
7 Sub spring 22 Secondary piston
8 Shim 23 Secondary piston return spring
9 Stem 24 Secondary valve body
10 Main spring 25 Secondary feed valve
11 Shim 26 Retainer
12 Guide ring 27 Secondary feed valve return spring
13 O-ring 28 Secondary feed valve retainer
14 Primary piston 29 C-ring
15 Guide 30 Exhaust port

A 2.9-4.9 {30-50, 2.2-3.6} B 5.9-7.4 {60-75, 4.3-5.4}
NOTICE
The parts in 4 and 13 are not the ones to be reusable.
OVERHAUL
EN0680202H200003
IMPORTANT POINTS - DISMOUNTING
1. REMOVE THE CLUTCH MASTER CYLINDER.

HINT
Even if without removing the clutch master cylinder, pedal bracket
can be removed only to the length of the clutch hose.
2. DISCONNECT THE NYLON TUBE.

NOTICE
Before disconnecting, apply aligning marks on the brake valve
SHTS068020200025
assembly and nylon tube.
3. REMOVE THE PEDAL BRACKET ASSEMBLY.

(1) Loosen the bolt and nut to remove the pedal bracket assembly.
NOTICE
WIPER LINK Before removing the pedal bracket, put the wiper link upward.
cardiagn.com
SHTS068020200026
4. REMOVE THE BRAKE PEDAL.

(1) Tap the shaft lightly using a brass rod and a hammer, remove the
brake pedal from the pedal bracket assembly.
NOTICE
Do not pull out the shaft because the brake pedal and the clutch
pedal are installed by one shaft.
SHTS068020200027
5. REMOVE THE BRAKE VALVE ASSEMBLY.

ALIGNING MARK (1) Apply aligning marks on the brake valve assembly and pedal
bracket assembly.
SHTS068020200028
IMPORTANT POINTS - DISASSEMBLY

ALIGNING NOTICE
MARK
Before disassembling the brake valve, apply aligning marks on
the brake valve cover, primary valve body and secondary valve
body.
SHTS068020200029
ALIGNING MARK
cardiagn.com
SHTS068020200030
1. REMOVE THE PRIMARY PISTON ASSEMBLY.
2. REMOVE THE SECONDARY VALVE BODY.
3. REMOVE THE SECONDARY PISTON.

NOTICE
Pull out with hands to prevent the seat part of the secondary pis-
ton from being damaged by using a pryer etc. If not with hands,
secondary piston should not be reused.
4. REMOVE THE PRIMARY FEED VALVE.

SHTS068020200031
5. REMOVE THE EXHAUST PORT.
6. REMOVE THE SECONDARY FEED VALVE.

NOTICE
In order to prevent from incorrect assembling, keep in stock
respectively primary feed valve assembly and secondary feed
valve assembly.
1. LUBRICATION
(1) When reassembling the brake valve, replace the O-rings and
retainer rings with new ones.
(2) Apply adequate amount of silicone grease on the grooves for the
O-ring and to the sliding surfaces of the component parts.
1. Secondary feed valve retainer O-ring
2. Secondary feed valve retainer
3. Secondary feed valve
4. Exhaust port O-ring
5. Primary feed valve retainer O-ring
6. Primary feed valve retainer
7. Secondary piston O-ring
8. Secondary piston
9. Primary valve body
10. Primary piston
11. Primary piston O-ring
12. Plunger
cardiagn.com
SHTS068020200032
2. ASSEMBLE THE STEM, SPRING, SPRING SEAT AND SHIM.

LOCK NUT
(1) Assemble the sub spring. At this time, adjust dimension "A" and
NUT "B" the spring compression "P" by means of the nut "B" and the shim.
Tightening Torque (Lock nut):
2.9-4.9 N⋅m {30-50 kgf⋅cm, 2.2-3.6 lbf⋅ft}
Dimension "A": 27.55-27.95 mm {1.0847-1.1003 in.}
Setting load "P": 0-9.8 N {0-1 kgf, 0-2.2 lbf}
DIMENSION
"A" NOTICE
In adjusting the spring compression, the axial play of the spring
must be removed.
SHTS068020200033
3. ALIGN THE VALVE COVER AND VALVE BODIES.

ALIGNING (1) When assemble the brake valve cover, primary body and second-
MARK ary body, align the marks which were applied at disassembly.
SHTS068020200029
ALIGNING MARK
cardiagn.com
SHTS068020200030
4. INSPECTION AND ADJUSTMENT

(1) Brake valve
a. Measure the secondary feed valve stroke (Dimension "A"
from starting to release the plunger to completing to fully
release the plunger).
A dimension: 0.6 mm {0.0236 in.} or above
DIMENSION "A"
SHTS068020200034
b. Connect the brake valve, nylon tube, air pressure gauge, and
air tank as shown in the figure.
c. Set the air tank pressure at 830 kPa {8.5 kgf/cm2, 120.87 lbf/
in.2}.
PRIMARY d. Apply soap water to the exhaust port and check to see there
is no air leakage.
AIR TANK
SECONDARY
SHTS068020200035
e. Drive in slowly the plunger. Measure the plunger stroke and

supply pressure at the point where the primary and second-
PLUNGER
ary air pressure gauges start to rise. If the measurements do
not match with the standard values, adjust by the shim of the
main spring.
PRIMARY
SUPPLY
PRESSURE Measurement item Standard value
AIR TANK
Plunger stroke 0.8-1.6 mm {0.0315-0.0630 in.}
19-41 kPa
Supply pressure
SECONDARY
{0.20-0.41 kgf/cm2, 2.76-5.94 lbf/in.2}
SHTS068020200036
f. Drive in further the plunger. Measure the plunger stroke and

supply pressure at the point immediately before that the pri-
PLUNGER
mary and secondary pressure increases rapidly (bending
point). If the measurements do not match with the standard
values, replace each spring.
PRIMARY
SUPPLY
PLUNGER Measurement item Standard value
AIR TANK
Supply pressure 196 kPa {2.00 kgf/cm2, 28.42 lbf/in.2}
cardiagn.com
SECONDARY
SHTS068020200037
g. Drive in further the plunger. Measure the plunger stroke and

supply pressure at the point where the primary and second-
PLUNGER
ary pressures increase rapidly. If the measurements do not
match with the standard values, replace each spring.
PRIMARY
SUPPLY Measurement item Standard value
PLUNGER
AIR TANK
Supply pressure 624 kPa {6.36 kgf/cm2, 90.50 lbf/in.2}
SECONDARY
SHTS068020200038
h. Drive in further the plunger. Measure the pedal stepping down

angle and supply pressure at the point where the primary and
PLUNGER
secondary pressure are maximum. If the measurements do
not match with the standard values, replace each spring.
PRIMARY
SUPPLY Measurement item Standard value
PLUNGER Plunger stroke 8.34-9.76 mm {0.3284-0.3842 in.}
AIR TANK
980 kPa
Supply pressure
{9.99 kgf/cm2, 142.14 lbf/in.2}
SECONDARY
SHTS068020200039
(2) Brake pedal

a. Make sure that the installing height of the brake pedal "C" and
the pedal play "B".
"B": 2-5 mm {0.0788-0.1968 in.}
"C": 147.7-157.7 mm {5.815-6.208 in.}
C
B
SHTS068020200040
b. If the pedal play is out of the standard value, loosen the lock
nut and turn the push rod to adjust the pedal play to the stan-
dard value.
Tightening Torque (Lock nut):
LOCK NUT 14-26 N⋅m {143-265 kgf⋅cm, 11-19 lbf⋅ft}
PUSH ROD
BOOT
PLUNGER
cardiagn.com
SHTS068020200041
(3) Check the clearance between stop lamp switch and buffer.
"D": 0.5-1.5 mm {0.0197-0.0590 in.}
STOP LAMP SWITCH
BUSHING
BUFFER
SHTS068020200042

EN0680202H300005
Main and sub spring: Main: 28.5 mm Replace, Measure and visual check
Free length/ 29.3 mm {1.15 in.}/ {1.12 in.} if necessary.
setting length/ 27.5 mm {1.08 in.}/ (Free length)
setting load 176.5 N
Crack, rust and damage {18 kgf, 39.68 lbf}
MAIN
Sub: 20.5 mm
21.6 mm {0.85 in.}/ {0.81 in.}
21.6 mm {0.85 in.}/ (Free length)
9.8 N SUB
{1.0 kgf, 2.20 lbf}
or more
Primary and secondary Primary: 40.5 mm Replace, measure and visual check
piston return spring: 43.2 mm {1.70 in.}/ {1.59 in.} if necessary.
Free length/ 16.5 mm {0.65 in.}/ (Free length)
setting length/ 95.1 N
setting load {9.7 kgf, 21.38 lbf}
Crack, rust and damage PRIMARY
cardiagn.com
Secondary: 43.2 mm
45.8 mm {1.80 in.}/ {1.70 in.}
49.0 N
{5.0 kgf, 11.02 lbf}
SECONDARY
Primary and secondary — — Replace, Visual check

piston: if necessary.
Wear and damage
SECONDARY PRIMARY
Primary and secondary — — Replace, Visual check

feed valve: if necessary.
Wear and damage
Primary and secondary Primary: 20.4 mm Replace, Measure and visual check
feed valve return spring: 21.4 mm {0.84 in.}/ {0.80 in.} if necessary.
Free length/ 12.5 mm {0.49 in.}/ (Free length)
setting length/ 52.0 N
setting load {5.3 kgf, 11.68 lbf}
Crack, rust and damage PRIMARY
Secondary: 21.8 mm
22.8 mm {0.90 in.}/ {1.13 in.}
49.0 N
{5.0 kgf, 11.02 lbf} SECONDARY
Secondary valve body: — — Replace, Visual check

Primary valve body: — — Replace, Visual check

cardiagn.com
PROTECTION VALVE (TYPE-A)

EN0680202I200005
Type Spring type

Open 637 kPa {6.5 kgf/cm2, 92.4 lbf/in.2}
Operating pressure
Close 510 kPa {5.2 kgf/cm2, 74.0 lbf/in.2}
DESCRIPTION
EN0680202C100006
cardiagn.com
SHTS068020200050
1 Valve body 5 Dust seal plate

2 O-ring 6 Retainer ring
3 Valve A Inlet
4 Compression spring B Outlet
COMPONENT LOCATOR
EN0680202D100005
cardiagn.com
SHTS068020200051
1 Body 4 Spacer 7 Dust seal plate

2 O-ring 5 Shim 8 Retainer ring
3 Piston 6 Spring 9 Dust seal
OVERHAUL
EN0680202H200004
1. LUBRICATION
(1) When reassembling the protection valve, replace the O-rings and
valve with new ones.
(2) Apply adequate amount of silicone grease to the sliding surface of
the component parts.
SHTS068020200052

EN0680202H300006
Unit: mm {in.}
Valve contact surface of — — Clean or Visual check
cardiagn.com
body cap 1: replace,
Sliding surface of valve — — Clean or

body 2: replace,
Valve spring: 60.0 {2.36} — Replace, Measure

Free length if necessary.
PROTECTION VALVE (TYPE-B)

EN0680202I200006
Type Spring type

Open 540 kPa {5.5 kgf/cm2, 78.3 lbf/in.2}
Operating pressure
Close 390 kPa {4.0 kgf/cm2, 56.6 lbf/in.2}
DESCRIPTION
EN0680202C100007
cardiagn.com
SHTS068020200055
1 Valve body 5 Dust seal plate

3 Valve A Inlet
4 Compression spring B Outlet
COMPONENT LOCATOR
EN0680202D100006
cardiagn.com
SHTS068020200056
1 Body 5 Spring
2 O-ring 6 Dust seal plate
3 Piston 7 Retainer ring
4 Shim
OVERHAUL
EN0680202H200005
1. LUBRICATION
(1) When reassembling the protection valve, replace the O-rings and
valve with new ones.
(2) Apply adequate amount of silicone grease to the sliding surface of
the component parts.
SHTS068020200057

EN0680202H300007
Unit: mm {in.}
Sliding surface of valve: — — Clean or Visual check
cardiagn.com
Rust, wear and damage replace,
if necessary.
Valve spring: 47.5 {1.87} — Replace, Measure

Free length if necessary.
PROTECTION VALVE (WITH 4-WAY PROTECTION VALVE)

EN0680202I200007
Type Spring type (4-way protection)

Opening pressure Open: Port 21, 22, 23 620-660 kPa {6.4-6.7 kgf/cm2, 89.93-95.72 lbf/in.2}
Port 24 570-610 kPa {5.9-6.2 kgf/cm2, 82.67-88.47 lbf/in.2}
Close: Port 21, 22, 24 440-480 kPa {4.5-4.8 kgf/cm2, 63.82-69.61 lbf/in.2}
Port 23 490-530 kPa {5.0-5.4 kgf/cm2, 71.07-76.87 lbf/in.2}
DESCRIPTION
EN0680202C100008
cardiagn.com
SHTS068020200059
1 Main spring A Port 21 (Outlet)

2 Dust cover B Port 22 (Outlet)
3 Check valve C Port 23 (Outlet)
4 Dust seal rubber D Port 24 (Outlet)
5 Piston E Inlet port
6 Valve spring F No.1 side
G Center check valve
H No.2 side
COMPONENT LOCATOR
EN0680202D100007
8 3
4
9
5
10
11 6
7
12
13
cardiagn.com
9
11
10
SHTS068020200060
1 Dust cover 6 Shim 11 Valve

2 Dust seal rubber 7 Spacer 12 Body
3 Retainer ring 8 Piston 13 Check valve
4 Dust seal plate 9 O-ring
5 Main spring 10 Valve spring
NOTICE
The parts in 3, 9 and 11 are not the ones to be reusable.
OVERHAUL
EN0680202H200006
1. LUBRICATION
(1) When assembling the protection valve use the new O-rings and
valves.
(2) Apply the silicone grease on the each sliding surface of the com-
ponent parts and O-ring groove.
• A: O-ring
• B: Sliding surface
cardiagn.com
SHTS068020200061
ADJUSTMENT
EN0680202H300008
AIR LEAKAGE
1. CHECK VALVE
(1) By-pass check valve at No.1 side.
a. Confirm no leakage of air at inlet port, when applying air pres-
sure 49 kPa {0.5 kgf/cm2, 7.11 lbf/in.2} and 392 kPa {4 kgf/
cm2, 56.89 lbf/in.2} from outlet port No.21 and No.22.
SHTS068020200062
(2) Center check valve

a. Confirm no leakage of air at the outlet port No.21 and No.22,
when applying air pressure 49 kPa {0.5 kgf/cm2, 7.11 lbf/in.2}
and 980 kPa {10 kgf/cm2, 142 lbf/in.2} from the inspection
port.
SHTS068020200063
(3) Check valve at No.2 side

a. Confirm no leakage of air at the inspection port, when apply-
ing air pressure 49 kPa {0.5 kgf/cm2, 7.11 lbf/in.2} and 980
kPa {10 kgf/cm2, 142 lbf/in.2} from the outlet port No.23 and
No.24.
2. OTHER AIR TIGHTNESS

(1) When applying air pressure 0-980 kPa {0-10 kgf/cm2, 0-142 lbf/
in.2}, confirm that any leakage of air should be 0 cm3min.
SHTS068020200064
PERFORMANCE CHRACTERISTIC
1. OPENING VALVE PRESSURE

(1) No.1 side
a. Releasing the compressed air at the outlet port No.21 and
No.22 to air, when applying the compressed air at the speed
specified below, confirm that air pressure of the compressed
air, saturated at the inlet should be of opening valve pressure,
which should be 620-660 kPa {6.3-6.7 kgf/cm2, 89.61-95.29
cardiagn.com
lbf/in.2}.
Charging speed: From 295 kPa {3.0 kgf/cm2, 42.66 lbf/in.2} to
490 kPa {5.0 kgf/cm2, 71.10 lbf/in.2} within 3-7 seconds.
(2) No.2 side
a. When applying air at charging speed specified below from the
inlet side under air pressure "0" at the outlet port No.23 and
No.24, confirm that a pressure at the inspection port when it
starting to go up at the outlet should be of opening valve pres-
sure, which should be 570-610 kPa {5.8-6.2 kgf/cm2, 82.49-
88.18 lbf/in2}.
Opening valve pressure

620-660 kPa
Port No.23
{6.3-6.7 kgf/cm2, 89.61-95.29 lbf/in.2}
570-610 kPa
Port No.24
{5.8-6.2 kgf/cm2, 82.67-88.47 lbf/in.2}
Charging speed: From 295 kPa {3.0 kgf/cm2, 42.66 lbf/in.2} to

490 kPa {5.0 kgf/cm2, 71.10 lbf/in.2} within 8-22 seconds.
2. CLOSING VALVE PRESSURE

(1) When discharging air through respective No.1 side and No.2 side
inlet under a pressure of 980kPa {10 kgf/cm2, 142 lbf/in.2} at the
inlet and the outlet, at discharging speed specified below, confirm
that a pressure when the pressures saturated should be of closing
valve pressure, which should be 440-480 kPa {4.5-4.8 kgf/cm2,
64.01-68.27 lbf/in.2} (Port No.21, 22 and 24), and 490-530 kPa
{5.0-5.4 kgf/cm2, 71.07-76.87 lbf/in.2} (Port No.23).
Discharging speed: From 590 kPa {6.0 kgf/cm2, 85.32 lbf/in.2} to
295 kPa {3.0 kgf/cm2, 42.66 lbf/in.2} within less than 3 seconds.
NOTICE
• Perform test again by increasing sims, when the respective
pressures is low and by decreasing it when high in the above
inspection.
• After inspecting, make sure to tighten the inspection port
securely.

EN0680202H300009
Unit: mm {in.}
Sliding surface and contact — — Replace, Visual check

surface of body: if necessary.
Wear and damage
Sliding surface and contact — — Replace, Visual check
cardiagn.com
surface of valve seat and if necessary.
piston:
Wear and damage
Main spring and valve spring: Main spring 137.3 N Replace, Measure and Visual check
Free length/ (Port 21, 22, 24): {14.0 kgf, if necessary.
Setting length/ 42.4 {1.67}/ 30.87 lbf}
Setting load 27.5 {1.08}/ (Setting load)
Crack, rust and damage 158.9 N
{16.2 kgf, 35.72 lbf}
Main spring
(Port 23):
35.3 {1.39}/ MAIN
27.5 {1.08}/
169.7 N
{17.3 kgf, 38.15 lbf}
VALVE
Valve spring: 0.69 N
20.0 {0.79}/ {0.07 kgf,
9.0 {0.35}/ 0.155 lbf}
0.78 N (Setting load)
{0.08 kgf, 0.175 lbf}
QUICK RELEASE VALVE

EN0680202I200008
Type Diaphragm type
DESCRIPTION
EN0680202C100009
cardiagn.com
SHTS068020200068
1 Cover 6 Bolt
2 Filter A Inlet
3 Gasket B Outlet
4 Diaphragm C Exhaust
5 Valve body
COMPONENT LOCATOR
EN0680202D100008
cardiagn.com
SHTS068020200069
1 Cover 4 Diaphragm
2 Filter 5 Valve body
3 Gasket 6 Bolt
OVERHAUL
EN0680202H200007
IMPORTANT POINT - DISASSEMBLY

NOTICE
Before disassemble the relay valve apply the aligning mark "A" for
the cover and valve body.
SHTS068020200070
1. ASSEMBLE THE RELAY VALVE.

(1) When assembly the relay valve, use the new diaphragm and gas-
ket.
cardiagn.com
• A: Gasket
• B: Diaphragm
(2) Coincide the aligning mark "A" which were applied at disassem-
bly.
SHTS068020200071

EN0680202H300010
Valve body and cover — — Replace, Visual check

surface: if necessary.
Rust and damage
LOAD SENSING VALVE

EN0680202I200009
Type Piston with diaphragm type
cardiagn.com
DESCRIPTION
EN0680202C100010
LOAD SENSING VALVE
cardiagn.com
SHTS068020200073
1 Cover 13 Operating arm

2 Air pipe 14 Body
3 Piston 15 Plunger return piston
4 Diaphragm guide 16 Plunger spring
5 Diaphragm A Inlet (From Brake valve)
6 Connecting rod B Outlet (To Relay valve)
7 Check valve (Exhaust) C Breathing
8 Cam D Exhaust
9 Cap E MAX.
10 Valve spring F Half
11 Valve G MIN.
12 Plunger
LINKAGE
cardiagn.com
SHTS068020200074
1 Load sensing valve 6 Connecting rod

2 Operating arm 7 Push rod
3 Adjuster A Rear axle
4 Holder B Rear-front axle
5 Damper assembly C Rear-rear axle
COMPONENT LOCATOR
EN0680202D100009
LOAD SENSING VALVE
cardiagn.com
SHTS068020200075
1 Cover 12 Piston seal 23 Plunger spring

2 O-ring 13 Piston 24 Cap
3 O-ring retainer 14 Diaphragm protector 25 Hexagonal socket screw
4 Air pipe 15 Diaphragm 26 Cam
5 Pipe retainer 16 Piston guide 27 Connecting rod
6 Filter 17 Plunger 28 Indicator
7 Diaphragm retainer 18 Body 29 Operating arm
8 Retainer ring 19 Oil seal 30 Cotter pin
9 Spring seat 20 Bushing 31 Washer
10 Valve spring 21 Check valve (Exhaust) 32 Valve No. plate
11 Valve 22 Plunger return piston 33 Diaphragm guide

A 7.8-9.8 {80-100, 5.76-7.22} B 3.4-4.9 {35-50, 2.51-3.61}
LINKAGE
cardiagn.com
SHTS068020200076
1 Load sensing valve 8 Pin 15 Supporter

2 Adjuster (Wire type) 9 Bracket (To Rear-front axle) 16 Spring seat
3 Lock plate 10 Holder assembly 17 Cover
4 Cotter pin 11 Bracket (To Rear-rear axle) 18 Spring
5 Damper assembly 12 Connector 19 Retainer
6 Bracket (To Rear axle) 13 Clamp band
7 Push rod 14 Connecting rod

A 35.3-52.0 {360-530, 27-38} C 19.6-39.2 {200-400, 15-28}
B 17.7-26.5 {180-270, 14-19} D 62.8-91.2 {640-930, 47-67}
OVERHAUL
EN0680202H200008
1. REMOVE THE OPERATING ARM.

(1) Measure and record the fixing length A of the operating arm
before removing.
SHTS068020200077
1. LUBRICATION
(1) When reassembling the L.S.V. replace all rubber parts (Piston
seal, Valves, Diaphragm, Dust seals and O-rings) with new ones.
cardiagn.com
(2) Apply lithium grease to each sliding surface of the components
parts and the O-ring groove.
A: O-ring
*L.S.V.: Load sensing valve
SHTS068020200078
2. ASSEMBLE THE OPERATING ARM.

(1) Set the dimension "A" of operating arm to the original length or
according to table below.
Unit: mm {in.}
Valve No. 47640-1280 47640-1080
A 84-86 {3.307-3.385} 59-61 {2.323-2.401}
NOTICE
Valve No. is indicated on the cover.
SHTS068020200077
3. INSPECTION OF THE LOAD SENSING VALVE

(1) Connect the L.S.V., nylon tube, air pressure gauge and air tank as
shown in the figure.
SHTS068020200079
(2) Set operating arm to the "A" position and close the outlet port;
then hold a charge with air at a pressure of 686 kPa {7.0 kgf/ cm2,
99.541 lbf/in.2} into the inlet port.
Let the operating arm swing over the entire range.
At this time, check for air leak by applying soapy water around the
body and pipe joint.
Valve No. 47640-1280 47640-1080

A +30° +15°
B -30° -15°
SHTS068020200080
NOTICE
(3) Set the air tank pressure at 686 kPa {7.0 kgf/cm2, 99.54 lbf/in2.},
fix the angle of the operating arm as specified below, and mea-
sure the pressure on the outlet port when compressed air is sup-
plied to the inlet port by using of the cock.
(4) For your information, the relation between angle of the operating
arm and pressure on the outlet port is shown in the adjacent dia-
grams.
Unit: kPa {kgf/cm2, lbf/in.2}
Operating arm Rated pressure on
cardiagn.com
Valve No.
angle outlet port
+30° 686 {7.0, 99.50}
47640-1020 0° C: 301-359 {3.1-3.6, 43.66-52.06}
47640-1280 -30° B: 170-210 {1.8-2.1, 24.66-30.45}
-40° A: 150-190 {1.6-1.9, 21.76-27.55}
+15° 686 {7.0, 99.50}
0° F: 321-379 {3.3-3.8, 46.56-54.96}
47640-1080
-15° E: 190-230 {2.0-2.3, 27.56-33.35}
SHTS068020200081
-20° D: 160-200 {1.7-2.0, 23.21-29.00}
NOTICE
12
690
DELIVERY PRESSURE (kPa)
590
490
390
290 F
200
E
98 D
0
–20 –15 –10 –5 0 5 10 15 20
OPERATING ARM ANGLE ( ) O
For: 47640-1080
SHTS068020200082
4. DAMPER ASSEMBLY
(1) Before installing the connecting rod to the spring seat, apply the
lock agent to the threads of the rod.
SHTS068020200083
5. PUSH ROD AND HOLDER ASSEMBLY (For tandem axle)

(1) When assembling the push rod and holder assembly, insert the
push rod ends to the connectors so that the groove on the push
rod and connector end will be flush as shown in the figure.
(2) Clamp band should be placed as shown in the figure.
cardiagn.com
SHTS068020200084
1. ADJUSTER (For single axle)

(1) Position of the lock plate:
After connection the operating arm of the L.S.V., adjust the
adjuster (wire) on the connecting rod then lock the wire as shown
in the figure.
A = 60 mm {2.36 in.}
SHTS068020200085
2. PUSH ROD WITH HOLDER ASSEMBLY (For tandem axle)

(1) Position of bolt for clamp band:
Set the clamp bands so that the bolts for clamp bands will be on
opposite sides of the propeller shaft and differential carrier.
(2) Inserting direction of the pin:
Connect the pin to the push rod as shown in the figure.
SHTS068020200086
ADJUSTMENT
EN0680202H300011
1. ADJUSTER
(1) With the vehicle unloaded, adjust the length of the wire to align
the indicator of the L.S.V. with the mark "•".
SHTS068020200087
(2) Lock the wire as shown in the figure.

a = 60 mm {2.36 in.}
cardiagn.com
SHTS068020200088
SHTS068020200089

EN0680202H300012
Inner surface of cover: — — Replace, Visual check

Wear, damage and rust if necessary.
Valve contact surface 1 — — Replace, Visual check

and friction surface 2 of if necessary.
piston:
Wear and damage
Friction surface of dia- — — Replace, Visual check

phragm guide: if necessary.
cardiagn.com
Wear and damage
Friction surface of piston — — Clean or replace. Visual check

guide:
Wear, damage and rust
Valve contact surface 1 — — Clean or replace, Visual check

plunger:
Friction surface of rod 1 — — Clean or replace, Visual check

and cam 2: if necessary.
Valve contact surface 1 — — Clean or replace, Visual check

plunger return piston:
Valve spring and plunger — — Replace, Visual check

spring: if necessary.
Elastic distortion and
damage
Friction surface of body 1 — — Clean or replace, Visual check

and bushing: if necessary.
Friction surface of cap: — — Clean or replace, Visual check

Wear, damage and rust if necessary.
Indicator 1, — — Repair or Visual check

Operating arm 2: replace.
Deformation
cardiagn.com
Connector: — — Replace, Visual check
Deterioration and damage if necessary.
Components of damper: — — Replace, Visual check

Deformation and damage if necessary.
Push rod assembly — — Replace, Visual check

(Tandem axle): if necessary.
Deformation
SPRING BRAKE CONTROL VALVE (TYPE-A)

EN0680202I200010
Type Variable pressure control type

Outlet pressure difference between parking and releas-
Within 147 kPa {1.5 kgf/cm2, 21.32 lbf/in.2}
ing stroke at a specified lever angle
DESCRIPTION
EN0680202C100011
1
2
Body cover
Feed valve spring
11
12
Handle return spring
Pull rod
SHTS068020200104
cardiagn.com
3 Piston 13 Knob
4 Feed valve 14 Compression spring
5 Valve seat 15 Release knob
6 Valve body 16 Handle body
7 Piston spring A Inlet
8 Valve spring B Outlet
9 Cam C Exhaust (PARK)
10 Cam holder
COMPONENT LOCATOR
EN0680202D100010
cardiagn.com
SHTS068020200105
1 Body cover 8 Valve spring

2 Shim 9 Valve seat
3 Piston spring 10 Handle body
4 Valve body 11 Stopper
5 Cam holder 12 Compression spring
6 O-ring 13 Knob sub assembly
7 Piston sub assembly 14 Pull rod

A 5.4-7.4 {55-75, 4.0-5.4} B 3.4-4.9 {35-50, 2.6-3.6}
OVERHAUL
EN0680202H200009

a
1. LUBRICATION
(1) When assembling the spring brake control valve, replace the feed
valve, valve seats and O-rings.
(2) Apply silicone grease to each sliding surface of the assembly
parts, O-rings and O-ring grooves.
a. O-ring
b. Feed valve
c. Piston
b c d e f
d. Valve seat
SHTS068020200106
e. Cam
f. Cam holder
2. ASSEMBLE THE CAM ASSEMBLY.

(1) When assembling the cam and cam holder, make sure that the
cam holder pin and spiral groove of the cam are aligned.
(2) When installing the cam assembly to the valve body, the valve
cardiagn.com
body pin and straight groove of the cam must be aligned.
SHTS068020200107
(3) Adjust dimension "A" with the shim.

a Assembly standard: 33.8-34.2 mm {1.331-1.346 in.}
a. Cam
A b. Cam holder
c. Shim
b c
SHTS068020200108
3. SPRING BRAKE CONTROL VALVE PERFORMANCE TEST

SPRING BRAKE (1) First, connect the pressure gauge to the outlet line and apply an
AIR
CONTROL VALVE
PRESSURE air pressure of 980 kPa {10.0 kgf/cm2, 142 lbf/in.2} to the inlet line.
GAUGE
TANK
SHTS068020200109
(2) Move the spring brake control lever towards the OFF position,
gradually and confirm that the air pressure in the outlet line meets
the characteristic shown in figure.
Standard:
Handle angle: Outlet pressure: kPa {kgf/cm2, lbf/in.2}
15° 275 {2.8, 39.9}
35° 441.6-500.4 {4.5-5.1, 64.0-72.6}
Over 42° 980 {10.0, 142}
NOTICE
The characteristic shown is under the inlet pressure of 480 kPa
{10.0 kgf/cm2, 142 lbf/in2.}
SHTS068020200110
(3) Confirm the following functions.

980
DISCHARGE PRESSURE (kPa)
a. The control handle is locked at PARK position.

883
785
b. The control handle automatically turn to OFF position when the
686
275 kPa lever is released at PARK position.
588 471 29.4 kPa
490
392
294
196
42
cardiagn.com
98
0
0 10 20 30 40 45 50 55
PARK 15 35
RELEASE
POSITION HANDLE ROTATION POSITION
ANGLE ( )
(AIR TANK PRESSURE: 980 kPa)
SHTS068020200111

EN0680202H300013
Unit: mm {in.}
Piston and valve body: — — Replace, Visual check

Cam, pin and cam — — Replace, Visual check

holder: if necessary.
Wear and damage
Piston spring, valve Piston spring 500.1 N Replace, Measure and visual check
spring and handle 27.9 {1.10}/ {51.0 kgf, 112.43 lbf} if necessary.
return spring: 25.0 {0.98}/ (Setting load)
Free length/ 553.1 N
cardiagn.com
Setting length/ {56.4 kgf, 124.34 lbf}
Setting load
Crack, rust and damage Valve spring 17.6 N
19.6 {0.77}/ {1.8 kgf, 3.96 lbf}
10.5 {0.41}/ (Setting load)
19.6 N
{2.0 kgf, 4.41 lbf}
VALVE SPRING
Handle return 6.9 N
spring {0.7 kgf, 1.55 lbf}
13.5 {0.53}/
7.8 N
{0.8 kgf, 1.76 lbf} PISTON SPRING
HANDLE RETURN
SPRING
Feed valve spring: — — Replace, Visual check

Rust and damage if necessary.
SPRING BRAKE CONTROL VALVE (TYPE-B)

EN0680202I200011

Outlet pressure difference between parking and releas-
Within 196 kPa {2.0 kgf/cm2, 28.43 lbf/in.2}
ing stroke at a specified lever angle
DESCRIPTION
EN0680202C100012
cardiagn.com
SHTS068020200116
1 Body cover 10 Cam holder 19 Retainer

2 Feed valve spring 11 Handle return spring 20 Feed valve
3 Piston 12 Pull rod 21 Plunger
4 Feed valve 13 Knob A Inlet
5 Valve seat 14 Compression spring B Outlet (To spring brake line)
6 Valve body 15 Release knob C Exhaust (PARK)
7 Piston spring 16 Handle body D Outlet (To multiple relay valve)
8 Valve spring A 17 Valve spring B
9 Cam 18 Return spring
COMPONENT LOCATOR
EN0680202D100011
cardiagn.com
SHTS068020200117
1 Body cover 11 Stopper

2 Shim 12 Compression spring
3 Piston spring 13 Knob sub-assembly
4 Valve body 14 Pull rod
5 Cam holder 15 Retainer
6 O-ring 16 Valve spring B
7 Piston sub-assembly 17 Feed valve
8 Valve spring A 18 Return spring
9 Valve seat 19 Plunger
10 Handle body

A 5.4-7.4 {55-75, 4.0-5.4} B 3.4-4.9 {35-50, 2.6-3.6}
OVERHAUL
EN0680202H200010
1. LUBRICATION
(1) When assembling the spring brake control valve, replace the feed
valve, valve seats and O-rings.
(2) Apply silicone grease to each sliding surface of the assembly
parts, O-rings and O-ring grooves.
a. O-ring
b. Feed valve
c. Piston
d. Valve seat
e. Cam
f. Cam holder
g. Plunger
cardiagn.com
SHTS068020200118
2. ASSEMBLE THE CAM ASSEMBLY.

(1) When assembling the cam and cam holder, make sure that the
cam holder pin and spiral groove of the cam are aligned.
(2) When installing the cam assembly to the valve body, the valve
body pin and straight groove of the cam must be aligned.
SHTS068020200119
(3) Adjust dimension "A" with the shim.

a Assembly standard: 33.8-34.2 mm {1.331-1.346 in.}
a. Cam
A b. Cam holder
c. Shim
b c
SHTS068020200108
3. SPRING BRAKE CONTROL VALVE PERFORMANCE TEST

SPRING BRAKE (1) First, connect the pressure gauge to the outlet line and apply an
AIR
CONTROL VALVE
PRESSURE air pressure of 980 kPa {10.0 kgf/cm2, 142 lbf/in.2} to the inlet line.
GAUGE
TANK
SHTS068020200109
(2) Move the spring brake control handle towards the OFF position,
gradually and confirm that the air pressure in the outlet line meets
the characteristic shown in figure below.
cardiagn.com
SHTS068020200120
NOTICE
The characteristic shown is under the inlet pressure of 980 kPa
B {10.0 kgf/cm2, 142 lbf/in.2}
DISCHARGE PRESSURE (kPa)
980
A- Outlet pressure (To multiple relay valve)
883 B- Outlet pressure (To spring brake line and multiple relay valve)
786 A
686
(3) Confirm the following functions.
588 a. The control handle is locked at PARK position.
490
392
b. The control handle automatically turn to OFF position when the
294 handle is released PARK position.
29.4
196
98
29.4
0
0 10 20 30 40 50 60
TEST 7 15 32.5 2 52 70
POSITION
HANDLE RELEASE
PARK ROTATION POSITION
POSITION ANGLE ( )
(AIR TANK PRESSURE: 980 kPa)
SHTS068020200121

EN0680202H300014
Unit: mm {in.}
Piston and valve body: — — Replace, Visual check

Cam, pin and cam — — Replace, Visual check

holder: if necessary.
Wear and damage
Piston spring, valve Piston spring 588.0 N Replace, Measure and visual check
spring, handle return 26.8 {1.06}/ {60.0 kgf, 132.19 lbf} if necessary.
spring: 24.8 {0.98}/ (Setting load)
Free length/ 651.7 N
cardiagn.com
Setting length/ {66.5 kgf, 146.50 lbf}
Setting load
Crack, rust and damage Valve spring A 17.6 N
19.6 {0.77}/ {1.8 kgf, 3.96 lbf}
19.6 N
{2.0 kgf, 4.41 lbf}
VALVE SPRING "A"
Handle return spring 6.9 N
19.3 {0.76}/ {0.7 kgf, 1.54 lbf}
7.8 N
{0.8 kgf, 1.76 lbf}
PISTON SPRING
Valve spring B 18.0 N HANDLE RETURN
11.2 {0.44}/ {1.8 kgf, 4.05 lbf} SPRING
19.6 N
{2.0 kgf, 4.41 lbf} RETURN
SPRING
Return spring 8.8 N
32.0 {1.26}/ {0.9 kgf, 1.98 lbf}
29.0 {1.14}/ (Setting
VALVE SPRING "B"
9.8 N load)
{1.0 kgf, 2.20 lbf}
Feed valve spring and — — Replace, Visual check

valve seat spring: if necessary.
Rust and damage
RELAY VALVE (TYPE-A)

EN0680202I200012
Type Diaphragm type with double check valve combined

Pressure difference between signal and outlet pressure 29.4 kPa {0.29 kgf/cm2, 4.26 lbf/in.2} or less
DESCRIPTION
EN0680202C100013
cardiagn.com
SHTS068020200123
1 Cover 9 Valve
2 Diaphragm 10 Plug
3 Valve body 11 Silencer
4 Valve sub assembly A Signal
5 Valve cap B Outlet
6 Spring C Exhaust
7 Valve D Inlet
8 Filter
COMPONENT LOCATOR
EN0680202D100012
cardiagn.com
SHTS068020200124
1 Valve sub assembly 9 Valve

2 Cover 10 O-ring
3 Guide 11 Spring
4 Valve 12 Valve cap
5 Gasket 13 Clip
6 Plug 14 Silencer
7 Filter 15 Pipe
8 Valve body 16 Dust cover

A 11.8-14.7 {120-150, 9-10} C 58.8-78.4 {600-800, 44-57}
B 34.3-44.1 {350-450, 26-32}
OVERHAUL
EN0680202H200011

NOTICE
Before disassembling the relay valve, mark the aligning marks "A"
cardiagn.com
on the cover and valve body.
SHTS068020200125
1. LUBRICATION
(1) When assembling the relay valve, use new O-rings and valves.
(2) Apply the silicone grease to each sliding surface of the compo-
A: O-ring
B: Apply the silicone grease
(3) When installing the cover to the body, align the aligning marks
which were applied at disassembly.
SHTS068020200126

EN0680202H300015
Unit: mm {in.}
Check valve: — — Replace, Visual check

Cover, guide and plug: — — Clean or Visual check

Damage, wear and rust replace,
if necessary.
Spring: 46 {1.81}/ 52.0 N Replace, Measure and Visual check

Free length/ 30 {1.18}/ {5.30 kgf, 11.69 lbf} if necessary.
cardiagn.com
Setting length/ 59.3 N (Setting load)
Setting load {6.05 kgf, 13.33 lbf}
Crack, rust and damage
Relay valve body and — — Clean or Visual check

cap replace,
sliding surface: if necessary.
Damage, wear and rust
RELAY VALVE (TYPE-B)

EN0680202I200013
Type Diaphragm type with double check valve combined

34 kPa {0.34 kgf/cm2, 4.93 lbf/in.2} or less
Pressure difference between signal and outlet pressure (At output pressure is 50 kPa {0.51 kgf/cm2, 7.25 lbf/
in.2} or more)
DESCRIPTION
EN0680202C100014
1 Piston 10 Body
SHTS068020200131
cardiagn.com
2 O-ring 11 Retainer
3 Valve spring 12 Inlet valve
4 Valve retainer 13 Piston spring
5 Valve guide 14 Cover
6 Valve seat A Signal
7 Exhaust valve B Outlet
8 Rivet C Exhaust
9 Retainer ring D Inlet
COMPONENT LOCATOR
EN0680202D100013
cardiagn.com
SHTS068020200132

2 Inlet valve 4 Silencer

A 12-19 {123-193, 8.9-14}
OVERHAUL
EN0680202H200012
1. LUBRICATION
A: O-ring
cardiagn.com
SHTS068020200133

EN0680202H300016
Unit: mm {in.}
Piston and sliding — — Replace, Visual check

surface of cover if necessary.
and valve body:
Wear and damage
Inlet valve, valve — — Clean or replace, Visual check

guide, valve retainer if necessary.
VALVE
and valve body slid- RETAINER
ing surface:
Wear and damage
VALVE
GUIDE
INLET
VALVE
Valve spring and Valve spring 21.8 N Replace, Measure and visual check
piston spring: 23.5 {0.93}/ {2.22 kgf, 4.90 lbf} if necessary.
Free length/ 15.7 {0.62}/ (Setting load)
Setting length/ 29.0 N
Crack, rust and
damage Piston spring 41.0 N
34.5 {1.36}/ {4.18 kgf, 9.22 lbf}
54.6 N
{5.57 kgf, 12.27 lbf}
CUT VALVE
EN0680202I200014
Type Spring type
DESCRIPTION
EN0680202C100015
cardiagn.com
SHTS068020200137
1 Valve cap 6 Conical spring

2 Piston A Signal
3 Valve body B Outlet
4 Compression spring C Inlet
5 Valve sub assembly D Exhaust
COMPONENT LOCATOR
EN0680202D100014
cardiagn.com
SHTS068020200138
1 Valve cap 4 Compression spring 7 Valve body

2 O-ring 5 Ring retainer 8 Valve sub assembly
3 Piston 6 Filter 9 Conical spring

A 49.04-58.83 {500-600, 36.2-43.3} B 49.04-58.83 {500-600, 36.2-43.3}
OVERHAUL
EN0680202H200013
1. LUBRICATION
(1) When assembling the cut valve, use the new O-ring and retainer
ring.
(2) Apply the silicone grease to the each sliding surface of the com-
ponent parts and O-ring groove.
NOTICE
Check the air leakage from exhaust port, with the piston at the
released position.
A: Sliding surface
SHTS068020200139
B: O-ring
PERFORMANCE CHARACTERISTIC
1. When the inlet pressure is 686 kPa {7.0 kgf/cm2, 99.54 lbf/
in.2}, the valve should be opened with the signal pressure of
below 343 kPa {3.5 kgf/cm2, 49.77 lbf/in.2} and the valve
should be closed with the signal pressure of 147-245 kPa
{1.5-2.4 kgf/cm2, 21.32-35.53 lbf/in.2}.
2. When the inlet and signal pressure are decreasing at same

time, the valve should be closed at pressure of 99-196 kPa
{1.0-2.0 kgf/cm2, 14.22-28.44 lbf/in.2}.
3. When the inlet and signal pressure are increasing at same

time, the valve should be opened with the pressure of 148-
245 kPa {1.5-2.5 kgf/cm2, 21.33-35.55 lbf/in.2}.

EN0680202H300017
Sliding surface and — — Replace, Visual check

valve contact sur- if necessary.
face of piston:
cardiagn.com
Wear and damage
Conical spring and Conical spring: 16.6 mm {0.66 in.} Replace, Visual check
compression 17.6 mm {0.69 in.}/ (Free length) if necessary.
spring: 15.4 mm {0.61 in.}/
Free length/ 0.08 N
setting length/ {0.008 kgf, 0.0180 lbf}
setting load
Crack, rust and Compression spring: 20.5 mm {0.81 in.} CONICAL
damage 22.5 mm{0.90 in.}/ (Free length)

15.5 mm {0.51 in.}/ 6.7 N
7.0 N {0.684 kgf, 1.5063 lbf}
{0.714 kgf, 1.5737 lbf} (Setting load) COMPRESSION
Valve body: — — Replace, Visual check

Sliding surface and if necessary.
contact surface:
Wear and damage
REDUCING VALVE (TYPE-A)

EN0680202I200015
Type Piston
520.4-559.6 kPa {5.4-5.7 kgf/cm2, 75.5-81.1 lbf/in.2} at inlet pressure 690 kPa {7.0
Outlet pressure
kgf/cm2, 100.0 lbf/in.2}
DESCRIPTION
EN0680202C100016
cardiagn.com
SHTS068020200143
1 Bracket 10 Spring
2 Cover 11 Spring seat
3 O-ring 12 Retainer
4 Valve body 13 Ring retainer
5 Spring 14 Valve seat
6 Piston 15 Check valve
7 Shim A Inlet
8 Valve B Outlet
9 Retainer C Exhaust
COMPONENT LOCATOR
EN0680202D100015
cardiagn.com
SHTS068020200144
1 Bracket 9 Retainer
2 Cover 10 Spring
3 O-ring 11 Spring seat
4 Valve body 12 Retainer
5 Spring 13 Ring retainer
6 Piston 14 Valve seat
7 Shim 15 Check valve
8 Valve

A 9.8-19.6 {100-200, 7.3-14.4}
OVERHAUL
EN0680202H200014
1. LUBRICATION
A: O-ring
cardiagn.com
SHTS068020200145

EN0680202H300018
Spring: — — Replace, Visual check

Valve body and piston — — Clean or replace, Visual check

Valve contact surface: — —

REDUCING VALVE (TYPE-B)

EN0680202I200016
Type Piston
784-824 kPa {8.0-8.4 kgf/cm2, 113.8-119.5 lbf/in.2} at inlet pressure 980 kPa {10.0
Outlet pressure
DESCRIPTION
EN0680202C100017
cardiagn.com
SHTS068020200148
1 Retainer ring 8 Piston

2 O-ring 9 Body
3 Valve spring 10 Valve
4 Shim 11 Valve cover
5 Lower cover A Inlet
6 Check valve B Outlet
7 Main spring C Exhaust
COMPONENT LOCATOR
EN0680202D100016
cardiagn.com
SHTS068020200149
1 Retainer ring 7 Piston

2 Cover 8 Shim
3 O-ring 9 Main spring
4 Valve spring 10 Lower cover
5 Valve 11 Check valve
6 Body

A 6.2-7.8 {64-79, 4.6-5.7}
OVERHAUL
EN0680202H200015
1. LUBRICATION
A: O-ring
cardiagn.com
SHTS068020200150

EN0680202H300019
Spring: — — Replace, Visual check

Valve body and piston — — Clean or replace, Visual check

Valve contact surface: — —

BRAKE CHAMBER
EN0680202I200017
Type Diaphragm type
DESCRIPTION
EN0680202C100018
cardiagn.com
SHTS068020200152
1 Push rod 5 Diaphragm

2 Return spring 6 Chamber cover
3 Chamber A Inlet
4 Clamp B Drain hole
COMPONENT LOCATOR
EN0680202D100017
cardiagn.com
SHTS068020200153
1 Push rod 6 Chamber cover

2 Return spring 7 Clamp nut
3 Chamber 8 Clamp bolt
4 Clamp 9 Spacer
5 Diaphragm

A 26.5-32.3 {270-330, 19.9-24.1}
OVERHAUL
EN0680202H200016
IMPORTANT POINT - DISMOUNTING
1. DISMOUNTING OF THE BRAKE CHAMBER

(1) Before dismounting, apply aligning mark A to the chamber, clamp
and chamber cover.
(2) Apply a position mark R or L to identify the side where the cham-
ber was installed.
SHTS068020200154
1. ASSEMBLING THE BRAKE CHAMBER

(1) Replace the diaphragm with new one.
(2) Align the aligning mark A of the chamber, clamp and chamber
cardiagn.com
cover.
(3) Insert the bolt from opposite side of drain hole and tighten the
bolts evenly with nut within the specified torque.
SHTS068020200155
2. CHECKING FOR AIR LEAKAGE

(1) Apply soapy water to the chamber as shown and charge with
compressed air of 830 kPa {8.5 kgf/cm2, 121 lbf/in.2} from the
inlet port A then check for leakage.
SHTS068020200156
3. INSTALLING CLEVIS
(1) Install the clevis to the push rod and adjust dimension A to the
specified value.
Assembly Standard: 84-86 mm {3.31-3.38 in.}
SHTS068020200157
IMPORTANT POINT - MOUNTING
1. INSTALLING THE BRAKE CHAMBER

(1) The chamber must be mounted on the side as marked when dis-
mounting.
NOTICE
• See the position mark (R or L) which was applied when dis-
mounting.
• When connecting the clevis with the slack adjuster, lubricate
the clevis pin hole and clevis pin with sufficient chassis
grease.

EN0680202H300020
Cover, clamp, push rod, — — Replace, Visual check

return spring and cham- if necessary.
ber:
Wear and damage
cardiagn.com
BRAKE CHAMBER (MAKER: WABCO)

EN0680202I200018
Type Diaphragm type
DESCRIPTION
EN0680202C100019
cardiagn.com
6 5
1 3 2 4
SHTS068020200159
1 Pressure plate 4 Push rod

2 Clamp ring 5 Base
3 Diaphragm 6 Push rod guide
COMPONENT LOCATOR
EN0680202D100018
cardiagn.com
SHTS068020200160
1 Pressure plate 8 Oil seal

2 Clamp ring 9 Tolerance ring
3 Diaphragm 10 Washer
4 Push rod 11 Guide
5 Base 12 Plate
6 Push rod guide 13 Bushing
7 Snap ring

A 25-30 {260-310, 18.8-22.4}
SPECIAL TOOL
EN0680202K100001
Prior to starting a brake chamber overhaul, it is necessary to have this special tool.
Illustration Part number Tool name Remarks
WEDGE CHAMBER STROKE

09714-1030
TOOL
OVERHAUL
EN0680202H200017
1. REMOVAL OF PRESSURE PLATE

CLAMP RING (1) Make a matching mark to base, clamp ring and pressure plate.
MARK
PRESSURE PLATE BASE

SHTS068020200162
(2) Mark clamp ring not to forget the inserting direction of clamp ring
bolt and remove clamp ring.
NOTICE
When removing clamp ring, do not expand the inserting portion of
clamp ring bolt by more than 80 mm {3.15 in.}.
cardiagn.com
DO NOT EXPAND MORE THAN 80 mm {3.15 in.}.
SHTS068020200163
(3) Remove pressure plate from base.
SHTS068020200164
2. REMOVAL OF DIAPHRAGM AND PUSH ROD

(1) Remove diaphragm and push rod from base.
NOTICE
• Push rod should be removed out, holding plate and repeating
to push and pull it straightly for a few times.
• When removing, push rod should not be pulled out up or
downward, toward right or left, not hammering from the
square flange side.
SHTS068020200165
3. REMOVAL OF PUSH ROD GUIDE

(1) Take out push rod guide out of the square flange.
NOTICE
When removing push rod guide, do not drop off a washer in it.
SHTS068020200166
4. REMOVAL OF GUIDE
(1) Remove snap ring, plate and oil seal with snap ring pliers.
NOTICE
Make sure not to jump out a snap ring.
(2) Remove guide, using a pipe having outer diameter of about φ37
mm {1.46 in.} and tapping with plastic hammer by making the
square flange of base upside.
cardiagn.com
SHTS068020200167
5. DISASSEMBLY OF PUSH ROD GUIDE ASSEMBLY

(1) Remove bushing and tolerance ring from push rod guide.
TOLERANCE RING
NOTICE
WASHER • Keep it surely as washer in the push rod guide may be
BUSHING reused when assembling it.
• There is a case that tolerance ring may be in the fitting hole
at the tip of push rod, in case of which, pick it up with screw-
driver, etc.
PUSH ROD GUIDE
SHTS068020200168
1. INSTALLATION OF GUIDE, OIL SEAL AND PLATE

(1) Apply lightly grease (stored in the repair kit) at moving portion of
push rod guide on base.
NOTICE
Never fail to use the grease, stored in the "REPAIR KIT".
SHTS068020200169
(2) Facing the flat side of new guide to diaphragm side, insert it until it
RING TYPE SPRING RETAINER touches down to base by tapping lightly with stick having an outer
diameter of about φ37 mm {1.46 in.} or box-socket.
NOTICE
• Confirm that ring type spring is installed on oil seal.
• Confirm that retainer is in its groove.
PLATE
OIL SEAL
GUIDE
SHTS068020200170
2. INSTALLATION OF PUSH ROD AND DIAPHRAGM

(1) Insert it to base by applying grease (stored in the "REPAIR KIT")
at the rod portion of push rod.
NOTICE
• Never fail to use grease, stored in the "REPAIR KIT".
• When installing push rod, make sure not to damage oil seal.
cardiagn.com
SHTS068020200171
3. INSTALLATION OF PRESSURE PLATE

(1) Putting pressure plate on base, align those matching marks.
SHTS068020200172
4. INSTALLATION OF CLAMP RING

(1) Matching clamp ring with the fitting mark, catch the both end at
bolt inserting portion of clamp ring with the vice gradually and
make its both end of ring come closer to approx. 15-20 mm {0.60-
0.78 in.} in the distance. After that, removing the vice, tighten tem-
MATCHING MARK
porally them toward inserting direction with the bolt and nut.
(2) Tap all periphery of clamp ring with plastic hammer and tighten
15-20 mm securely the nut. Repeat this 2-3 times for gradual tightening.
{0.60-0.78 in.} CATCH IT IN THE VICE.
SHTS068020200173
5. INSTALLATION OF PUSH ROD GUIDE

(1) Putting new bush into pushing rod guide, insert it deeply to base
SPECIAL TOOL
until push rod guide contacts with the internal hole of push rod
guide by special tool.
SST: Wedge Chamber Stroke Tool (09714-1030)
NOTICE
In this case, do not install tolerance ring and washer.
THE SURFACE TO
CHECK THE DIMENSION
SHTS068020200174
(2) Under the status that the special tool remains pushed against
138 Unit: mm push rod guide, piling washers on the depression for adjustment
at the end-face of special tool and picking out one top washer
102.1
piled up, determine Max. quantity of washers, installable in the
30
internal diameter of base.
NOTICE
37
30
The washer quantity at this time is adjusted one for setting dimen-
sion of push rod guide. Accordingly, keep them securely.
13
THE SURFACE TO CHECK DIMENSION HINT
cardiagn.com
DEPRESSION FOR WASHER ADJUSTMENT • Do not mind to use the washers picked out in dismounting.
SHTS068020200175 • Target for washer quantity: 0-4 pcs.
• Washer thickness (1 pierce): 0.5 mm {0.02 in.}
(3) Picking out special tool and push rod guide for a while and install-
ing the washer of quantities determined in the above (3) and new
tolerance ring on push rod guide, insert it deeply with special tool
again until push rod guide contacts with the bottom.
NOTICE
• Be careful not to drop off the washers.
• After installing, confirm that, under the status that the spe-
cial tool remains pushed against push rod guide, the end-
face of base side is almost identical with the surface to check
setting dimension of special tool.
(4) Apply grease at the depression portion of push rod guide.
Using grease:
COSMO Heat-resistant grease B No. 2 or equivalent.
6. INSPECTION AFTER INSTALLATION

(1) When adding air of 700-800 kPa {7.2-8.2 kgf/cm2, 102-116 lbf/
SERVICE BRAKE PORT in2.} to service brake port, check that push rod moves smoothly.
(2) Make sure not to leak air from diaphragm.
SHTS068020200176

EN0680202H300021
Pressure plate, clamp, — — Replace, Visual check

push rod, diaphragm and if necessary
base:
Wear and damage
cardiagn.com
SPRING BRAKE CHAMBER

EN0680202I200019
Spring and piston type brake chamber combined with diaphragm type chamber
Type
with breather tube
cardiagn.com
DESCRIPTION
EN0680202C100020
cardiagn.com
SHTS068020200178
1 Retainer 15 Clamp band

2 Release bolt 16 Diaphragm
3 Slotted nut 17 Service brake chamber
4 Spring pin 18 Compression spring
5 Dust cover 19 Push rod
6 Spring brake chamber 20 Clevis
7 Spring 21 Breather tube
8 Piston ring A Spring brake air port
9 O-ring (Emergency and parking) - for releasing air
10 Piston B Service brake air port (Service) - for braking air
11 Retainer ring C Spring brake portion
12 Bushing D Service brake portion
13 Piston follower E Drain hole
14 Bulkhead
SPECIAL TOOL
EN0680202K100002
Prior to starting a spring brake chamber overhaul, it is necessary to have this special tool.
SPRING BRAKE PISTON

09683-1051
RELEASE BOLT
COMPONENT LOCATOR
EN0680202D100019
1 Dust cover 10 Retainer 19 Push rod

SHTS068020200180
cardiagn.com
2 Spring pin 11 Plain washer 20 Spring retainer
3 Slotted nut 12 Release bolt 21 Compression spring
4 Caution plate 13 Retainer ring 22 Clamp band
5 Spring brake chamber 14 Bushing 23 Spacer
6 Spring 15 Bulkhead 24 Clamp band bolt
7 Piston ring 16 Chamber cover bolt 25 Service brake chamber
8 Piston 17 Piston follower 26 Clevis
9 O-ring 18 Diaphragm 27 Breather tube

A 39.0-44.0 {400-450, 29-32} D 39.0-49.0 {400-500, 29-36}
B 9.8-17.6 {100-180, 7.3-13.0} E 26.5-32.3 {270-330, 20-23}
C 39.0-49.0 {400-500, 29-36}
OVERHAUL
EN0680202H200018
IMPORTANT POINT - DISMOUNTING
1. DISMOUNTING THE CHAMBER ASSEMBLY

(1) Before dismounting the chamber, turn the release bolt counter-
clockwise to release the spring brake.
(2) Apply a position mark R or L to make clear the side where the
chamber was installed.
SHTS068020200181

NOTICE
Before disassembling, put aligning marks to the clamp band, ser-
vice brake chamber, bulkhead and spring brake chamber.
cardiagn.com
SHTS068020200182
1. DISASSEMBLING THE SPRING BRAKE CHAMBER

(1) Remove the piston follower and then remove the dust cover,
spring pin and release bolt.
SHTS068020200183
(2) Use a press or special tool to hold the spring in compression then
remove the chamber cover bolt.
SST: Spring Brake Piston Release Bolt (09683-1051)
SHTS068020200184
1. LUBRICATION
(1) When assembling the spring brake chamber, replace the piston
ring, bushing and O-ring with new ones.
(2) Apply grease or oil to each point.
• a Silicone grease: O-ring, Bushing, Piston ring and

Spring brake chamber inner side.
• b Bearing grease: Release bolt
• c Rust preventive oil: Spring
SHTS068020200185
2. ASSEMBLING THE SPRING BRAKE CHAMBER

(1) Attach guide bolts to align the holes.
NOTICE
Align the aligning marks of the spring brake chamber and bulk-
head.
cardiagn.com
SHTS068020200186
(2) Use a press or special tool to compress the spring then tighten
the chamber cover with the bolts.
SST: Spring Brake Piston Release Bolt (09683-1051)
SHTS068020200187
(3) Screw in the release bolt until its head contacts the piston flange,
then return the release bolt one or two turns, then install the slot-
ted nut and spring pin.
NOTICE
The spring pin should be installed as shown in the figure.
SHTS068020200188
(4) Install the piston follower on the piston.

NOTICE
Apply locking adhesive (LOCTITE 242 or equivalent) to the thread
of the piston follower.
SHTS068020200189
3. ASSEMBLING THE SERVICE BRAKE CHAMBER

(1) Turn the release bolt counterclockwise to compress the spring of
the spring brake chamber.
NOTICE
To make turning easy, apply compressed air to the spring brake
chamber.
cardiagn.com
SHTS068020200190
(2) When reassembling the chamber, replace the diaphragm with

new one.
NOTICE
Align the aligning marks of the chamber, clamp band and bulk-
head.
(3) Insert the clamp band bolts from opposite side of drain hole and
tighten the bolts evenly with nuts within specified torque.
SHTS068020200191
(4) Turn the release bolt clockwise to release the spring of the spring
brake chamber.
SHTS068020200192
4. INSPECTION FOR AIR LEAKAGE

(1) Apply compressed air of 834 kPa {8.5 kgf/cm2, 121 lbf/in.2} to
both inlet ports marked "E" and "S", and make sure that there is
no air leakage from the joints of the assembly.
SHTS068020200193
5. INSPECTION FOR PISTON MOVEMENT

(1) Apply compressed air of 640-830 kPa {6.5-8.5 kgf/cm2, 93-120
lbf/in.2} to the inlet port with mark E gradually and make sure that
the push rod is completely returned.
Piston stroke: 64 mm {2.52 in.}
for spring brake chamber parts No.
47850 -4290/ -4300/ -4310/ -4320/ -4330/
-4340/ -4350/ -4360
: 56 mm {2.20 in.}
cardiagn.com
47850 -4370/ -4380/ -4390/ 4400
SHTS068020200194
6. INSTALLING THE CLEVIS

(1) Install the clevis to the push rod and adjust dimension "A" to the
specified value.
A: 261-263 mm {10.28-10.35 in.}
47850-4290/ -4300/ -4330/ -4340
A: 84-86 mm {3.31-3.38 in.}
47850-4310/ -4320/ -4350/ -4360/ -4370/ -4380/ -4390/ -4400
SHTS068020200360
1. INSTALLING THE CHAMBER ASSEMBLY

(1) Before mounting, turn the release bolt counterclockwise to
release the spring brake.
NOTICE
• Note the position mark R or L on the chamber which mark
was applied when dismounting and install it to its former
side.
• When connecting the clevis with slack adjuster, lubricate cle-
vis pin-hole and clevis pin with sufficient chassis grease.
SHTS068020200181
(2) After mounting, the release bolt must be set at the specified
torque.

EN0680202H300022
Inspection item Standard Limit Remedy Inspection procedure

Piston: — — Replace, Visual check
Chamber: — — Replace, Visual check

Spring and compression spring: — — Replace, Visual check

cardiagn.com
SPRING BRAKE CHAMBER (MAKER: NABCO)

EN0680202I200020
Type Spring and piston type brake chamber combined with diaphragm type chamber
DESCRIPTION
EN0680202C100021
cardiagn.com
SHTS068020200199
1 Elbow 4 Diaphragm
2 Clamp 5 Push rod assembly
3 Piggyback 6 Base
COMPONENT LOCATOR
EN0680202D100020
11
10
6
7
9
8
3
1
A
2
cardiagn.com
4
12
: Apply grease (Dynamax No.2: COSMO OIL CO., LTD product or equivalent).
SHTS068020200200
1 Elbow 7 Pin
2 Clamp 8 Bushing
3 Piggyback 9 Push rod guide
4 Diaphragm 10 Push rod boot
5 Push rod assembly 11 Push rod
6 Spring 12 Base

A 14.7-20.0 {150-204, 11.0-14.8}
OVERHAUL
EN0680202H200019
1. DISASSEMBLY OF THE SPRING BRAKE CHAMBER
! WARNING
Piggyback is very dangerous because there is very strong spring
inside it. Never disassemble the piggyback.
SHTS068020200201
(1) Disconnect the breather tube from the service chamber side
ELBOW BREATHER TUBE elbow.
NOTICE
• Do not disconnect the breather tube from the piggyback side.
• Pulling the center of the elbow obliquely can easily discon-
cardiagn.com
nect the breather tube from the elbow.
SHTS068020200202
(2) Apply the aligning mark on the clamp, piggyback and base.
(3) Remove the clamp, the piggyback and diaphragm from the
bracket.
(4) Remove the ring and pin, then disassemble the push rod assem-
bly.
SHTS068020200203
1. ASSEMBLY OF THE PUSH ROD ASSEMBLY

(1) Before assembling, apply grease (Dynamax No.2: COSMO OIL.,
LTD. product or equivalent) to each component parts.
SHTS068020200204
2. ASSEMBLY OF THE SPRING BRAKE CHAMBER

(1) Apply grease to inside of the bracket, and install the push rod
assembly, new diaphragm, piggyback and clamp.
NOTICE
• Do not adhere grease to the diaphragm.
• Before assembling, align the aligning marks on the clamp,
piggyback and bracket.
• Spring cylinder (piggyback) portion should be changed every
3 years, even though it does not fail.
• Diaphragm, dust cover and bushing, etc. are the parts to be
SHTS068020200203
changed periodically.
(2) After wiping the breather tube, apply lock agent (LOCTITE 414 or
equivalent) on the tube open end.
13 mm {0.512 in.} (3) Insert the breather tube in the elbow as shown in the figure.
ELBOW or MORE BREATHER TUBE
cardiagn.com
SHTS068020200205
3. INSPECTION FOR AIR LEAKAGE

lbf/in.2} to both inlet ports marked "E" and "S", and make sure that
there is no air leakage from the joints of the assembly.
SHTS068020200206
4. INSPECTION FOR PISTON MOVEMENT

lbf/in.2} to the inlet port marked "E" gradually and measure the
service chamber stroke.
Piston stroke: 58-61 mm {2.28-2.40 in.}

EN0680202H300023
Bracket, push rod, dia- — — Replace, Visual check

phragm and piggyback: if necessary
Wear and damage
SPRING BRAKE CHAMBER (MAKER: WABCO)

EN0680202I200021
Type Spring and piston type brake chamber combined with diaphragm type chamber
DESCRIPTION
EN0680202C100022
cardiagn.com
3 7 2 6 5 4
SHTS068020200208
1 Elbow 5 Push rod guide

2 Clamp 6 Push rod
3 Spring brake cylinder 7 Diaphragm
4 Base
COMPONENT LOCATOR
EN0680202D100021
cardiagn.com
SHTS068020200209
1 Elbow 10 Plate
2 Plug 11 Oil seal
3 Filter 12 Guide
4 Tube 13 Tolerance ring
5 Spring brake cylinder 14 Washer
6 Clamp ring 15 Push rod guide
7 Diaphragm 16 Bushing
8 Push rod 17 Base
9 Snap ring

A 25-30 {260-310, 18.8-22.4}
SPECIAL TOOL
EN0680202K100003
Prior to starting a spring brake chamber overhaul, it is necessary to have this special tool.
WEDGE CHAMBER STROKE

09714-1030
TOOL
OVERHAUL
EN0680202H200020

SPRING CYLINDER SERVICE CHAMBER
! WARNING
• Before disassembling it, check and verify that the release
bolt is extruded.
• Spring cylinder is very dangerous because there is very
strong spring inside it. Never disassembly the spring cylin-
der.
RELEASE BOLT
SHTS068020200210
1. REMOVAL OF BREATHER TUBE

BREATHER TUBE (1) Remove off breather tube from service chamber side.
NOTICE
When carrying or moving to other place it, don't hold breather
ELBOW tube.
cardiagn.com
(2) Remove the filter in the elbow.
SERVICE
CHAMBER
SHTS068020200211
2. REMOVAL OF SPRING CYLINDER

SPRING CYLINDER (1) Make a matching mark to base, clamp ring and spring cylinder.
MARK
CLAMP RING
BASE
SHTS068020200212
(2) Mark clamp ring not to forget the inserting direction of clamp ring
bolt and remove clamp ring.
NOTICE
When removing clamp ring, do not expand the inserting portion of
clamp ring bolt by more than 80 mm {3.15 in.}.
DO NOT EXPAND MORE THAN 80 mm {3.15 in.}.

SHTS068020200163
(3) Remove spring cylinder from base.
SHTS068020200213
3. REMOVAL OF DIAPHRAGM AND PUSH ROD

(1) Remove diaphragm and push rod from base.
NOTICE
• Push rod should be removed out, holding plate and repeating
to push and pull it straightly for a few times.
• When removing, push rod should not be pulled out up or
downward, toward right or left, not hammering from the
square flange side.
cardiagn.com
SHTS068020200165
4. REMOVAL OF PUSH ROD GUIDE

(1) Take out push rod guide out of the square flange.
NOTICE
When removing push rod guide, do not drop off a washer in it.
SHTS068020200166
5. REMOVAL OF GUIDE
(1) Remove snap ring, plate and oil seal with snap ring pliers.
! WARNING
Make sure not to jump out a snap ring.
(2) Remove guide, using a pipe having outer diameter of about φ37
mm {1.46 in.} and tapping with plastic hammer by making the
square flange of base upside.
SHTS068020200167
6. DISASSEMBLY OF PUSH ROD GUIDE ASSEMBLY

(1) Remove bushing and tolerance ring from push rod guide.
TOLERANCE RING
NOTICE
WASHER • Keep it surely as washer in the push rod guide may be
BUSHING reused when assembling it.
• There is a case that tolerance ring may be in the fitting hole
at the tip of push rod, in case of which, pick it up with screw-
driver, etc.
PUSH ROD GUIDE
SHTS068020200168
7. REMOVAL OF ELBOW
(1) By inserting a stick of φ6 - φ8 mm {0.24-0.31 in.} or screw-driver
from inserting side of elbow hose, remove the plug from base,
tapping with plastic hammer.
cardiagn.com
SHTS068020200214
1. MOUNTING OF ELBOW
(1) Install new elbow on base. In that case, set the direction of elbow
tip to be faced toward diaphragm side and put plug in from the tip
of elbow. Inserting the stick used in dismounting it or screw-driver,
insert it so that both tips of plug and elbow may be aligned by tap-
ping lightly with plastic hammer.
NOTICE
• Check and verify if the direction of plug and its installing
condition are shown in the figure.
• When inserting the stick or the screw-driver, make sure not
to damage elbow with their tips.
• After installing plug, make sure that elbow is not taken out by
a force of 60 N {6.1 kgf, 27 lbf}.
ELBOW REVERSE INSTALLED
PLUG
NOT ALIGNED
CORRECT INCORRECT INCORRECT
SHTS068020200215
2. INSTALLATION OF GUIDE, OIL SEAL AND PLATE

(1) Apply lightly grease (stored in the repair kit) at moving portion of
push rod guide on base.
NOTICE
Never fail to use the grease, stored in the "REPAIR KIT".
SHTS068020200216
(2) Facing the flat side of new guide to diaphragm side, insert it until it
RING TYPE SPRING RETAINER touches down to base by tapping lightly with stick having an outer
diameter of about φ37 mm {1.46 in.} or box-socket.
NOTICE
• Confirm that ring type spring is installed on oil seal.
• Confirm that retainer is in its groove.
PLATE
OIL SEAL
GUIDE
cardiagn.com
SHTS068020200217
3. INSTALLATION OF PUSH ROD AND DIAPHRAGM

(1) Insert it to base by applying grease (stored in the "REPAIR KIT")
at the rod portion of push rod.
NOTICE
• Never fail to use grease, stored in the "REPAIR KIT".
• When installing push rod, make sure not to damage oil seal.
SHTS068020200171
4. INSTALLATION OF SPRING CYLINDER

(1) Putting spring cylinder on base, align those matching marks.
SHTS068020200218
5. INSTALLATION OF CLAMP RING

(1) Matching clamp ring with the fitting mark, catch the both end at
bolt inserting portion of clamp ring with the vice gradually and
make its both end of ring come closer to approx. 15-20 mm {0.60-
0.78 in.} in the distance. After that, removing the vice, tighten tem-
MATCHING MARK
porally them toward inserting direction with the bolt and nut.
(2) Tap all periphery of clamp ring with plastic hammer and tighten
15-20 mm securely the nut. Repeat this 2-3 times for gradual tightening.
{0.60-0.78 in.} CATCH IT IN THE VICE.
SHTS068020200219
6. INSTALLATION OF PUSH ROD GUIDE

LEFT WHEEL (1) Add into the parking brake side port a compressed air of 700-800
SERVICE BRAKE SIDE PORT kPa {7.2-8.2 kgf/cm2, 102-116 lbf/in.2}
BREATHER TUBE
cardiagn.com
PARKING BRAKE SIDE PORT
SHTS068020200220
RIGHT WHEEL
BREATHER TUBE
SERVICE BRAKE SIDE PORT

SHTS068020200221
(2) Putting new bushing into push rod guide, insert it deeply to base
until push rod guide contacts with the internal hole of push rod
SPECIAL TOOL guide by special tool.
SST: Wedge Chamber Stroke Tool (09714-1030)
NOTICE
In this case, do not install tolerance ring and washer.
THE SURFACE TO
CHECK THE DIMENSION
SHTS068020200222
(3) Under the status that the special tool remains pushed against
138 Unit: mm push rod guide, piling washers on the depression for adjustment
at the end-face of special tool and picking out one top washer
102.1
piled up, determine Max. quantity of washers, installable in the
30
internal diameter of base.
NOTICE
37
30
The washer quantity at this time is adjusted one for setting dimen-
sion of push rod guide. Accordingly, keep them securely.
13
THE SURFACE TO CHECK DIMENSION HINT

DEPRESSION FOR WASHER ADJUSTMENT • Do not mind to use the washers picked out in dismounting.
SHTS068020200175 • Target for washer quantity: 0-4 pcs.
• Washer thickness (1 pierce): 0.5 mm {0.02 in.}
(4) Picking out special tool and push rod guide for a while and install-
ing the washer of quantities determined in the above (3) and new
tolerance ring on push rod guide, insert it deeply with special tool
again until push rod guide contacts with the bottom.
NOTICE
• Be careful not to drop off the washers.
• After installing, confirm that, under the status that the spe-
cial tool remains pushed against push rod guide, the end-
face of base side is almost identical with the surface to check
cardiagn.com
setting dimension of special tool.
(5) Exhaust the air of parking brake side port.
(6) Apply grease at the depression portion of push rod guide.
Using grease:
COSMO Heat-resistant grease B No. 2 or equivalent.
7. INSTALLATION OF BREATHER TUBE

BREATHER TUBE (1) Insert new filter into the tip of breather tube, after which it should
ELBOW be inserted into elbow. In this case, make sure that the hose
bulge should come to the center between two protuberant por-
tions, located at the end of elbow.
NOTICE
• Pay attention to the direction of filter. (Its small path side
should be tube side)
• When inserting breather tube into elbow, do not apply any
grease or the like.
SHTS068020200223
8. INSPECTION AFTER INSTALLATION

LEFT WHEEL (1) When adding air of 700-800 kPa {7.2-8.2 kgf/cm2, 102-116 lbf/
SERVICE BRAKE SIDE PORT in.2} to service brake side port or parking brake side port, check
that push rod moves smoothly.
BREATHER TUBE
(2) Make sure not to leak air from diaphragm.

SHTS068020200224
RIGHT WHEEL
BREATHER TUBE
cardiagn.com
SERVICE BRAKE SIDE PORT
SHTS068020200225

EN0680202H300024
Base, push rod, dia- — — Replace, Visual check

phragm and spring brake if necessary
cylinder:
Wear and damage
TRAILER HAND BRAKE CONTROL VALVE

EN0680202I200022
DESCRIPTION
EN0680202C100023
SHTS068020200227
cardiagn.com
1 Cam 7 Feed valve 13 Steel ball
2 Spring 8 Piston 14 Holder
3 Handle 9 Inner spring A Inlet
4 Shim 10 Cover B Outlet
5 Conical spring 11 Outer spring C Exhaust
6 Valve body 12 Exhaust valve
COMPONENT LOCATOR
EN0680202D100022
cardiagn.com
SHTS068020200228
1 Valve body 8 Cam 15 Retainer ring

2 O-ring 9 Holder 16 Valve seat
3 Exhaust valve 10 Spring 17 Feed valve
4 Conical spring 11 Cover 18 Piston
5 Spring seat 12 Pin 19 Inner spring
6 Shim 13 Handle 20 Outer spring
7 Steel ball 14 Connector

A 9.8-19.6 {100-200, 8-14} C 2.5-3.9 {25-40, 1.9-2.8}
B 5.4-7.4 {55-75, 4.0-5.4}
OVERHAUL
EN0680202H200021

NOTICE
Before disassembling the hand brake valve, mark the aligning
mark "A" on the holder and valve body.
SHTS068020200229
1. LUBRICATION
(1) When assembling the hand brake valve, use new O-ring and feed
valve.
cardiagn.com
(2) Apply silicone grease to each sliding surface of the component
parts and O-ring groove.
a. O-ring
b. Contact of steel ball
c. Sliding surface
(3) Align the aligning mark of the holder and valve body.
SHTS068020200230
IMPORTANT POINTS - ADJUSTMENT
1. EXHAUST VALVE FITTING HEIGHT

(1) Measure the exhaust valve fitting height "L" and adjust it.
NOTICE
Adjust this dimension with shims.
L: 38.3-38.7 mm {1.508-1.523 in.}
SHTS068020200231
2. HAND BRAKE VALVE PERFORMANCE CHARACTERISTIC

a. Air pressure at outlet port (kPa {kgf/cm2, lbf/in.2})
b. Handle turning angle (°)
Part No. -1341
(a1) (a2)
a 19.6-68.6 313.6-411.8
{0.2-0.7, 2.8-9.9} {3.2-4.2, 45.5-59.7}
(b1) (b2)
b
7-13 37-43
cardiagn.com
SHTS068020200232 Part No. -1350/ -1360
(a1) (a2)
a 19.6-68.6 421-559
{0.2-0.7, 2.8-9.9} {4.3-5.7, 61.1-81.0}
(b1) (b2)
b
7-13 42-48
NOTICE
The characteristic shown in both diagrams are for inlet air pres-
sure of 690 kPa {7.0 kgf/cm2, 99.54 lbf/in.2}.
The characteristic can be adjusted by changing the shim thick-
ness of the steel ball and of the outer spring.

EN0680202H300025
Unit: mm {in.}
Sliding surface of — — Replace, Visual check

exhaust valve: if necessary.
Wear and damage
Conical spring: 28.5 {1.12}/ 29.4 N Replace, Measure and visual check
Free length/ 18 {0.71}/ {3.0 kgf, if necessary.
Setting length/ 31.4 N 6.61 lbf}
Crack, rust and damage {3.2 kgf, 7.06 lbf} (Setting load)
cardiagn.com
Spring, outer spring and Spring 44.1 N Replace, Measure and Visual check
inner spring: 25 {0.98}/ {4.5 kgf, 9.92 lbf} if necessary.
Free length/ 15 {0.59}/ (Setting load)
Setting length/ 50.0 N
Crack, rust and damage
SPRING
Outer spring 29.5 {1.16}
31.3 {1.23}/ (Free length)
30.5 {1.20}/ 122.6 N
152.0 N {12.5 kgf, 27.56 lbf}
{15.5 kgf, 34.17 lbf} (Setting load) OUTER SPRING
Inner spring 27.5 {1.08}

28.5 {1.12}/ (Free length) INNER SPRING
18 {0.71}/ 28.4 N
31.4 N {2.9 kgf, 6.39 lbf}
{3.2 kgf, 7.06 lbf} (Setting length)
Piston and valve seat: — — Replace, Visual check

Cam and steel ball: — — Replace, Visual check

Valve body: — — Replace, Visual check

cardiagn.com
WHEEL BRAKE (TYPE: S-CAM BRAKE)

EN0680202I200023
Drum brake with internally expanding, leading-trailing shoes

Type
operating by cam shaft and slack adjuster in all wheels.
Brake drum inside With ISO type wheel 406.4 mm {16.0 in.} for both front and rear
diameter With spoke type wheel 440.0 mm {17.3 in.} for both front and rear
Front 152 x 15.5 mm {6.0 x 0.61 in.}

With ISO type wheel
Brake lining Rear 216 x 15.5 mm {8.5 x 0.61 in.}
Width x Thickness Front 127 x 15.5 mm {5.0 x 0.61 in.}
With spoke type wheel
Rear 203 x 15.5 mm {8.0 x 0.61 in.}
cardiagn.com
DESCRIPTION
EN0680202C100024
FRONT (With ISO type wheel)
cardiagn.com
SHTS068020200239
1 Brake shoe return spring 10 Spring brake chamber

2 Lubrication fitting 11 Hole plug
3 Slack adjuster 12 Brake shoe
4 Cam shaft 13 Brake lining
5 Anchor pin 14 Wheel sensor (If so equipped)
6 Brake spider 15 Sensor ring (If so equipped)
7 Brake drum 16 Brake chamber
8 Brake drum cover A Front
9 Brake chamber bracket
FRONT (With spoke type wheel)
cardiagn.com
SHTS068020200240
1 Brake shoe return spring 8 Brake drum cover

2 Lubrication fitting 9 Brake chamber bracket
3 Slack adjuster 10 Spring brake chamber
4 Cam shaft 11 Hole plug
5 Anchor pin 12 Brake shoe
6 Brake spider 13 Brake lining
7 Brake drum A Front
REAR-FRONT (With ISO type wheel)
cardiagn.com
SHTS068020200241
1 Anchor pin 9 Lubrication fitting

2 Brake spider 10 Brake shoe return spring (Inner)
3 Brake drum 11 Brake shoe return spring (Outer)
4 Brake drum cover 12 Brake lining
5 Cam shaft 13 Brake shoe
6 Slack adjuster 14 Wheel sensor (If so equipped)
7 Spring brake chamber 15 Sensor ring (If so equipped)
8 Brake chamber bracket A Front
REAR-FRONT (With spoke type wheel)
cardiagn.com
SHTS068020200242
1 Anchor pin 8 Brake chamber bracket

2 Brake spider 9 Lubrication fitting
3 Brake drum 10 Brake shoe return spring (Inner)
4 Brake drum cover 11 Brake shoe return spring (Outer)
7 Spring brake chamber A Front
REAR-REAR (With ISO type wheel)
cardiagn.com
SHTS068020200243

2 Brake spider 10 Brake shoe return spring (Inner)
3 Brake drum 11 Brake shoe return spring (Outer)
4 Brake drum cover 12 Brake lining
5 Cam shaft 13 Brake shoe
6 Slack adjuster 14 Wheel sensor (If so equipped)
7 Brake chamber 15 Sensor ring (If so equipped)
8 Brake chamber bracket A Front
REAR-REAR (With spoke type wheel)
cardiagn.com
SHTS068020200244
1 Anchor pin 8 Brake chamber bracket

2 Brake spider 9 Lubrication fitting
3 Brake drum 10 Brake shoe return spring (Inner)
4 Brake drum cover 11 Brake shoe return spring (Outer)
7 Brake chamber A Front
SPECIAL TOOL
EN0680202K100004
Prior to starting a wheel brake overhaul, it is necessary to have these special tools.
09683-1070 SPRING PULL BACK TOOL
09420-1510 ANCHOR PIN PULLER
09684-1010 ANCHOR PIN TOOL
cardiagn.com
COMPONENT LOCATOR
EN0680202D100023
FRONT (With ISO type wheel)
cardiagn.com
SHTS068020200248
1 Retainer ring 17 Anchor pin 33 Seal

2 Thrust washer 18 Brake shoe assembly (Trailing) 34 Roller
3 Slack adjuster 19 Brake drum 35 Brake shoe
4 Collar 20 Spring cover 36 Bracket (If so equipped)
5 Oil seal 21 Brake shoe return spring 37 Auto slack adjuster
(If so equipped)
6 Brake chamber bracket 22 Brake shoe assembly (Leading) 38 Pin (If so equipped)
7 Pin 23 Cam shaft 39 Spacer (If so equipped)
8 Washer 24 Collar 40 Plate (If so equipped)
9 Cotter pin 25 O-ring 41 Indicator (If so equipped)
10 Clevis 26 Bushing 42 Lock washer (If so equipped)
11 Spring brake chamber 27 Lubrication fitting 43 Wheel sensor (If so equipped)
12 Hole plug 28 Spacer 44 Sleeve (If so equipped)
13 Brake drum cover 29 Rivet 45 Brake chamber
14 Brake spider 30 Brake lining 46 Roller pin
15 Retainer 31 Spring pin
16 Lock plate 32 Retainer ring

A 119-225 {1,214-2,294, 88-165} D 246-324 {2,509-3,303, 182-238}
B 109-147 {1,112-1,498, 81-108} E 20.5-39.5 {210-402, 16-29}
C 34.5-51.5 {352-525, 26-37}
FRONT (With spoke type wheel)
cardiagn.com
SHTS068020200249
1 Retainer ring 16 Lock plate 31 Spring pin

2 Thrust washer 17 Anchor pin 32 Retainer ring
3 Slack adjuster 18 Brake shoe assembly (Trailing) 33 Seal
4 Collar 19 Brake drum 34 Roller
5 Oil seal 20 Spring cover 35 Brake shoe
6 Brake chamber bracket 21 Brake shoe return spring 36 Bracket (If so equipped)
7 Pin 22 Brake shoe assembly (Leading) 37 Auto slack adjuster
(If so equipped)
8 Washer 23 Cam shaft 38 Pin (If so equipped)
9 Cotter pin 24 Collar 39 Spacer (If so equipped)
10 Clevis 25 O-ring 40 Plate (If so equipped)
11 Spring brake chamber 26 Bushing 41 Indicator (If so equipped)
12 Hole plug 27 Lubrication fitting 42 Lock washer (If so equipped)
13 Brake drum cover 28 Spacer 43 Roller pin
14 Brake spider 29 Rivet
15 Retainer 30 Brake lining

A 119-225 {1,214-2,294, 88-165} D 246-324 {2,509-3,303, 182-238}
B 109-147 {1,112-1,498, 81-108} E 393-471 {4,008-4,802, 290-347}
C 34.5-51.5 {352-525, 26-37}
REAR-FRONT (With ISO type wheel)
cardiagn.com
SHTS068020200250
1 Retainer ring 19 Lock plate 37 Holder (If so equipped)

2 Slack adjuster 20 Brake shoe assembly (Trailing) 38 Pin (If so equipped)
3 Thrust washer 21 Brake shoe return spring 39 Brake lining
(Inner)
4 Collar 22 Brake shoe return spring 40 Rivet
(Outer)
5 Oil seal 23 Spring cover 41 Cotter pin
6 Bushing 24 Brake drum 42 Pivot pin
7 Plate (If so equipped) 25 Spring pin 43 Spring pin
8 Auto slack adjuster 26 Brake shoe assembly (Leading) 44 Retainer ring
(If so equipped)
9 Bracket (If so equipped) 27 Cam shaft 45 Seal
10 Brake chamber bracket 28 Collar 46 Roller
11 Cotter pin 29 O-ring 47 Roller pin
12 Washer 30 Bushing 48 Brake shoe
13 Pin 31 Brake spider 49 Bushing
14 Spring brake chamber 32 Spacer 50 Lock washer (If so equipped)
15 Hole plug 33 Connector 51 Indicator (If so equipped)
16 Brake drum cover 34 Lubrication fitting 52 Spacer (If so equipped)
cardiagn.com
17 Anchor pin 35 Wheel sensor (If so equipped)
18 Retainer 36 Sleeve (If so equipped)

A 109-147 {1,112-1,498, 81-108} D 168-226 {1,714-2,304, 124-166}
B 119-225 {1,214-2,294, 88-165} E 20.5-39.5 {210-402, 16-29}
C 34.5-51.5 {352-525, 26-37}
REAR-FRONT (With spoke type wheel)
cardiagn.com
SHTS068020200251
1 Retainer ring 18 Retainer 35 Indicator (If so equipped)

2 Slack adjuster 19 Lock plate 36 Spacer (If so equipped)
3 Thrust washer 20 Brake shoe assembly (Trailing) 37 Pin (If so equipped)
4 Collar 21 Brake shoe return spring 38 Plate (If so equipped)
(Inner)
5 Oil seal 22 Brake shoe return spring 39 Brake lining
(Outer)
6 Bushing 23 Spring cover 40 Rivet
7 Lock washer (If so equipped) 24 Brake drum 41 Cotter pin
8 Auto slack adjuster 25 Spring pin 42 Pivot pin
(If so equipped)
9 Bracket (If so equipped) 26 Brake shoe assembly (Leading) 43 Spring pin
10 Brake chamber bracket 27 Cam shaft 44 Retainer ring
11 Cotter pin 28 Collar 45 Seal
12 Washer 29 O-ring 46 Roller
13 Pin 30 Bushing 47 Roller pin
14 Spring brake chamber 31 Brake spider 48 Brake shoe
15 Hole plug 32 Spacer 49 Bushing
16 Brake drum cover 33 Connector
cardiagn.com

A 109-147 {1,112-1,498, 81-108} D 34.5-51.5 {352-525, 26-37}
B 119-225 {1,241-2,294, 88-165} E 168-226 {1,714-2,304, 124-166}
C 393-471 {4,008-4,802, 290-347}
REAR-REAR (With ISO type wheel)
cardiagn.com
SHTS068020200252
1 Brake chamber 19 Brake spider 37 Bushing

2 Pin 20 Cam shaft 38 Retainer ring
3 Washer 21 Retainer 39 Roller pin
4 Cotter pin 22 Lock plate 40 Seal
5 Brake chamber bracket 23 Brake shoe assembly (Leading) 41 Roller
6 Retainer ring 24 Brake shoe return spring 42 Lock washer (If so equipped)
(Inner)
7 Slack adjuster 25 Brake shoe return spring 43 Indicator (If so equipped)
(Outer)
8 Thrust washer 26 Brake shoe assembly (Trailing) 44 Spacer (If so equipped)
9 Collar 27 Spring pin 45 Pin (If so equipped)
10 Oil seal 28 Brake drum 46 Auto slack adjuster
(If so equipped)
11 Bushing 29 Brake lining 47 Plate (If so equipped)
12 O-ring 30 Cotter pin 48 Bracket (If so equipped)
13 Spacer 31 Washer 49 Sleeve (If so equipped)
14 Hole plug 32 Clamp 50 Holder (If so equipped)
15 Brake drum cover 33 Brake shoe 51 Wheel sensor (If so equipped)
16 O-ring 34 Pivot pin 52 Cam shaft bracket
cardiagn.com
17 Lubrication fitting 35 Rivet
18 Anchor pin 36 Spring pin

A 50-68 {510-693, 37-50} D 34.5-51.5 {352-525, 26-37}
B 119-225 {1,214-2,294, 88-165} E 168-226 {1,714-2,304, 124-166}
C 109-147 {1,112-1,498, 81-108} F 20.5-39.5 {210-402, 16-29}
REAR-REAR (With spoke type wheel)
cardiagn.com
SHTS068020200253
1 Brake chamber 18 Anchor pin 35 Rivet

2 Pin 19 Brake spider 36 Spring pin
3 Washer 20 Cam shaft 37 Bushing
4 Cotter pin 21 Retainer 38 Retainer ring
5 Brake chamber bracket 22 Lock plate 39 Roller pin
6 Retainer ring 23 Brake shoe assembly (Leading) 40 Seal
7 Slack adjuster 24 Brake shoe return spring 41 Roller
(Inner)
8 Thrust washer 25 Brake shoe return spring 42 Lock washer (If so equipped)
(Outer)
9 Collar 26 Brake shoe assembly (Trailing) 43 Indicator (If so equipped)
10 Oil seal 27 Spring pin 44 Spacer (If so equipped)
11 Bushing 28 Brake drum 45 Pin (If so equipped)
12 O-ring 29 Brake lining 46 Auto slack adjuster
(If so equipped)
13 Spacer 30 Cotter pin 47 Plate (If so equipped)
14 Hole plug 31 Washer 48 Bracket (If so equipped)
15 Brake drum cover 32 Clamp 49 Cam shaft bracket
16 O-ring 33 Brake shoe
cardiagn.com
17 Lubrication fitting 34 Pivot pin

A 50-68 {510-693, 37-50} D 34.5-51.5 {352-525, 26-37}
B 119-225 {1,214-2,294, 88-165} E 168-226 {1,714-2,304, 124-166}
C 109-147 {1,112-1,498, 81-108} F 393-471 {4,008-4,802, 290-347}
OVERHAUL
EN0680202H200022
1. REMOVAL OF TIRE
(1) Refer to chapter for WHEEL & TIRE.
2. REMOVAL OF BRAKE DRUM WITH WHEEL HUB AND WHEEL

HUB BEARINGS.
(1) Refer to chapter FRONT AXLE and REAR AXLE.
3. REMOVAL OF BRAKE SHOE RETURN SPRING

(1) Using the special tool, remove the return spring.
(FRONT WHEEL)
SST: Spring Pull Back Tool (09683-1070)
SHTS068020200254
cardiagn.com
(2) Using the special tool, remove the outer return spring.
(REAR WHEEL)
SHTS068020200255
(3) Turn the pivot pin and pull out the spring pin then remove the
return spring, inner. (REAR WHEEL)
SHTS068020200256
4. REMOVAL OF ANCHOR PIN

(1) Remove the lock plate and anchor pin retainer.
(2) Using the special tool, remove the pin and the brake shoe assem-
bly.
SST: Anchor pin puller (09420-1510)
SHTS068020200257
5. REMOVAL OF CAM SHAFT AND SLACK ADJUSTER

(1) If the vehicle is equipped with spring brake chamber, before
removing the cam shaft and slack adjuster, release the spring
brake.
NOTICE
Before removing the slack adjuster and cam shaft, apply a mark to
them to make clear the side (Left or Right) where they were
installed.
SHTS068020200258
1. INSPECTION OF SLACK ADJUSTER

(1) Measure the axial play and if the play exceed the limit, inspect the
spline of cam shaft and disassemble the adjuster.
Dimension "A": 150 mm {5.9 in.}
Assembly Standard: 1.5 mm {0.06 in.}
Service Limit: 3.0 mm {0.12 in.}
cardiagn.com
SHTS068020200259
(2) Measure the circumference play and if the play exceed the limit,
inspect the spline of cam shaft and disassemble the adjuster.
Dimension "A": 150 mm {5.9 in.}
Assembly Standard: 3.0 mm {0.12 in.}
Service Limit: 10.0 mm {0.39 in.}
SHTS068020200260
2. ASSEMBLY OF SLACK ADJUSTER

(1) Install the body cover.
(2) Use new rivets and caulk the rivet ends.
NOTICE
Apply enough chassis grease on the worm gear shaft before
installing the cover.
SHTS068020200261
(3) Tighten the worm gear shaft stopper fully then loose it by 1/12-1/6
turn.
NOTICE
• Replace the O-ring with new one.
• Apply enough chassis grease on the worm gear shaft before
installing the worm gear shaft.
SHTS068020200262
(4) Install the lock ball, spring and plug.

(5) After tighten the plug, caulk it to the body by a punch.
NOTICE
Apply enough chassis grease on the lock ball and spring.
cardiagn.com
SHTS068020200263
3. REPLACEMENT OF BRAKE LINING

(1) Remove the brake lining from the brake shoe.
a. Drill the rivet caulking section with a drill smaller than the rivet
diameter.
NOTICE
At this time, be careful not to scratch the brake shoe.
SHTS068020200264
b. After drilling, remove the remaining portion of the rivet with a

fine chisel or a riveting machine.
SHTS068020200265
(2) Install the brake lining to the brake shoe.

NOTICE
If a notched lining is used, the brake shoe and brake lining should
be installed as shown in figure.
SHTS068020200266
a. Set the lining on the shoe and insert the rivets into all holes,
then hold them in place with adhesive tape "A".
cardiagn.com
SHTS068020200267
b. Caulk the rivets lightly in a circular pattern as shown in figure

"B", repeat several times assure proper seating of the lining.
Recommended configuration of punch: shown in "C".
Recommended force of staking the rivet: 2.4 tons.
c. Remove adhesive tape.
SHTS068020200268
4. ASSEMBLY OF BRAKE SHOE

(1) Seals "A" for roller "B" should be replaced with new ones.
(2) Apply adequate amount of heat resistance grease on the roller
and seals.
SHTS068020200269
5. INSTALLATION OF O-RING AND OIL SEAL

(1) When assembling the wheel brake, replace the O-rings and oil
seals with new ones.
NOTICE
• The lip parts of the seal should always be facing outside.
• The seal should be caulked to the bracket (or bracket spider)
with a punch.
cardiagn.com
SHTS068020200270
6. INSTALLATION OF CAM SHAFT AND SLACK ADJUSTER

(1) Apply adequate amount of chassis grease on the O-ring, oil seal
and bushing before installing the cam shaft.
(2) If the clearance "A" between the retainer ring and slack adjuster
exceed 2.0 mm {0.078 in.}, install the washer between them.
NOTICE
Install the cam shaft and slack adjuster on the correct side (Left or
Right) according to the mark on them which were applied when
disassembling.
SHTS068020200271
NOTICE
• Make sure that the slack adjuster is installed, so that the
arrow on the adjuster points to the direction of the brake
chamber rod stroke as shown in figure.
• When connecting the slack adjuster with the brake chamber
and/or spring brake chamber, lubricate the clevis pin-hole
and the pin with sufficient chassis grease.
SHTS068020200272
(3) If the vehicle is equipped with a spring brake chamber, after con-
necting the slack adjuster with the brake chamber push rod, turn
the spring brake release bolt clockwise and securely tighten (with
mechanical released device).
SHTS068020200273
7. INSTALLATION OF CAM SHAFT AND AUTO SLACK

ADJUSTER (IF SO EQUIPPED)
(1) Apply adequate amount of chassis grease on the O-ring, oil seal
and bushing before installing the cam shaft.
(2) Make sure that the auto slack adjuster is installed so that the
arrow on the adjuster points in the direction of the brake chamber
rod stroke, as shown in figure.
NOTICE
Install the cam shaft and auto slack adjuster on the correct side
(Left or Right) according to the mark which was applied when dis-
cardiagn.com
assembly.
SHTS068020200274
(3) Make sure that clearance "A" between the spacer and auto slack
adjuster is 0.5-2.0 mm {0.020-0.078 in.}. Install or remove the
washer to maintain the required clearance.
SHTS068020200275
(4) When connection the auto slack adjuster with the brake chamber
and/or spring brake chamber, lubricate the clevis pin-hole and pin
with sufficient chassis grease.
(5) If the clevis pin-hole and auto slack adjuster pin-hole are mis-
aligned, turn the set screw of auto slack adjuster for clockwise.
SHTS068020200276
(6) Rotate by hand, the control arm as for as possible in the direction
of the arrow on the adjuster point.
(7) Make sure that clearance between set bolt and control arm is cor-
rect, and tighten the nut.
SHTS068020200277
(8) If the spring brake chamber is the equipped, after connecting the
auto slack adjuster with the brake chamber push rod, turn the
spring brake release bolt for clockwise fully (with mechanical
released device).
cardiagn.com
SHTS068020200273
8. INSTALLATION OF BRAKE SHOE ASSEMBLY

(1) Apply adequate amount of heat resistance grease on the bushing
of the brake shoe.
(2) Set the brake shoe assembly in place, then insert the anchor pins.
SHTS068020200278
(3) Using the special tool, set the grooves of the two anchor pin paral-
lel and then insert the retainer in the grooves so that the retainer
hole and brake spider hole are aligned.
SST: Anchor Pin Tool (09684-1010)
SHTS068020200279
(4) Place the lock plate on the retainer so that its hole is aligned with
the lock plate hole, then insert the bolt and tighten it.
SHTS068020200280
9. INSTALLATION OF BRAKE SHOE RETURN SPRING

(1) Hook the inner spring to the clamp and turn the pivot pin to align
the holes, then insert the spring pin. (REAR WHEEL)
NOTICE
Painted part of the spring must be placed in the upper side.
cardiagn.com
SHTS068020200281
(2) Use the special tool to install the return spring. (FRONT WHEEL,
REAR WHEEL - OUTER SPRING).
NOTICE
The folded part of the spring cover must be placed in the upper
side.
SHTS068020200282
10. INSTALL THE WHEEL SENSOR. (IF SO EQUIPPED)

(1) Push in the clamping bushing until the stopper makes contact with
the wheel sensor holder.
(2) Push the wheel sensor forcefully into the clamping bushing until
you feel that the wheel sensor has contact with the sensor ring.
NOTICE
When inserting the wheel sensor, do not tap on it with a hammer
or attempt to pry it into place using a screwdriver, or the like.
Doing so could damage the wheel sensor.
(FRONT)
SHTS068020200283
(3) Arrange the wire harness.
(REAR)
SHTS068020200284
11. ASSEMBLE THE BRAKE DRUM AND WHEEL HUB.

(FRONT WHEEL)
(1) See the mark located at 1 or 1' on the brake drum as shown in fig-
ure. Install the drum according to NOTICE.
NOTICE
• The drums, number with R or L.
With R: Install in right side.
With L: Install in left side.
• The drums, with no R or L.
cardiagn.com
New drums: Install in any side.
Reused drums: Install in the side originally installed.
SHTS068020200285
(2) When assembling the brake drum and wheel hub, make sure that
their aligning marks are aligned as close to each other as possi-
ble.
NOTICE
Position of marks are located at 2 as shown in the figure. (Broken
line shows alternative position).
12. MOUNTING OF WHEEL HUB WITH BRAKE DRUM

(1) Refer to chapter FRONT AXLE and REAR AXLE.
NOTICE
1. Be careful not to push back the wheel sensor too far when
mounting the wheel hub and brake drum. Also, make sure
they are straight so that you do not bump the tip of the wheel
sensor.
2. When inserting the outer hub bearing, avoid tapping on it
with a hammer as this will expose the wheel sensor to
bumps. Insert the outer hub bearing carefully using a lock
nut.
(2) Slowly turn the wheel hub and brake drum and confirm that they
move smoothly.
13. MOUNTING OF TIRE

(1) Refer to chapter WHEEL & TIRE.
14. GREASING
(1) After completion of assembly, lubricate the bushings of the brake
spider, cam shaft bracket (REAR WHEEL) and slack adjuster wire
with chassis grease from the lubrication fittings.
15. ADJUSTMENT
(1) Finally, adjust the brake chamber rod stroke as explained in Sec-
tion "ADJUSTMENT".
ADJUSTMENT
EN0680202H300026
1. REMAINING THICKNESS OF THE BRAKE LINING

(1) Check remaining thickness of lining through the inspection hole of
the brake drum cover. If the lining has been worn to the limit
marking or if it is foreseen that the lining will be worn to the limit by
the time the next inspection is made, replace the lining.
SHTS068020200286
2. AIR PRESSURE IN THE AIR TANK

(1) Operate the engine and obtain an air pressure of the 690 kPa {7.0
NOTICE
The specified air pressure in the air tank should be maintained
when making the adjustment.
cardiagn.com
SHTS068020200287
3. ADJUST THE BRAKE CHAMBER STROKE

(1) Lift the wheel to be adjusted off the ground.
(2) Step on the brake pedal several times while turning the wheel in
the forward direction to make sure that the brake shoes are cor-
rectly positioned.
NOTICE
In the case of spring brake chamber, set the spring brake control
valve to the "OFF" position.
SHTS068020200288
(3) Turn the worm gear shaft of the slack adjuster clockwise fully and
then turn it back at least two notches.
SHTS068020200289
(4) Depress the brake pedal fully and measure the brake chamber
push rod stroke "A".
Assembly standard: 22-30 mm {0.87-1.18 in.}
Repair limit: Brake chamber: 40 mm {1.57 in.}
Spring brake chamber: 45 mm {1.77 in.}
SHTS068020200290
(5) While turning the wheel by hand in the forward direction, step on
the brake pedal several times to make sure that the brake shoes
are correctly positioned.
cardiagn.com
SHTS068020200288
(6) Make sure that there is no dragging, when turning the wheel by
hand. If there is any dragging, repeat the operation over again
from (2).
NOTICE
In accordance with the same procedure as above, adjust the
stroke for all wheels.
SHTS068020200291

EN0680202H300027
Unit: mm {in.}
Slack adjuster body: — — Replace, Visual check

Wear and damage. if necessary.
Slack adjuster, worm — — Replace, Visual check

gears: if necessary.
Wear and damage.
Slack adjuster, body cover: — — Replace, Visual check

cardiagn.com
Cam shaft: 39.8 {1.57} 39.5 {1.56) Replace. Measure
Diameter.
Clearance between cam 0.23-0.30 0.6 Replace

shaft and bushing of brake {0.0091-0.0110} {0.024} bushing and/
spider, chamber bracket, or cam shaft.
cam shaft bracket.
Cam shaft collar and — — Replace, Visual check

spacer: if necessary.
Wear and damage.
Brake drum: — — Regrind or Visual check

Cracks and damage. replace,
if necessary.
Brake drum: 406.4 {16.0} Regrind Regrind or Visual check

Inside diameter. 409.4 replace.
{16.12}
Service
410.4
{16.16}
440.0 {17.3} Regrind

443.0
{17.44}
Service
444.0
{17.48}
Brake drum: 0-0.1 0.2 Regrind or Measure

Run out. {0-0.0039} {0.0079} replace.
cardiagn.com
Brake shoe assembly: — — Replace, Visual check
Cracks and damage. if necessary.
Brake lining: 15.5 {0.61} 5.5 Replace. Visual check

Thickness. {0.217}
Clearance between brake 0.02-0.07 0.25 Replace the Visual check

shoe bushing and anchor {0.0008-0.0027} {0.0098} brake shoe
pin. bushing and/
or anchor
pin.
Brake shoe roller and pin: — — Replace, Visual check

Brake shoe return spring — — Replace, Visual check

and spring cover: if necessary.
Damage, Lacking elastic
strength distortion.
WHEEL BRAKE (TYPE: WEDGE BRAKE)

EN0680202I200024
Drum brake with internally expanding, leading-trailing shoes operating by expander in

Type
all wheels.
Brake drum inside diameter 406.4 mm {16.0 in.} for both front and rear.
Front 152 x 15.5 mm {6.0 x 0.61 in.}
216 x 15.5 mm {8.5 x 0.61 in.} (Models: FR, FS, FY, ZS)
Frontward
Brake lining 203 x 15.5 mm {8.0 x 0.61 in.} (Models: SH, SS)
Width x Thickness Rear 152 x 15.5 mm {6.0 x 0.61 in.} (Model: FR)
Rearward 216 x 15.5 mm {8.5 x 0.61 in.} (Models: FS, FY)
203 x 15.5 mm {8.0 x 0.61 in.} (Model: SS)
DESCRIPTION
EN0680202C100025
cardiagn.com
FRONT
SHTS068020200305
1 Brake shoe return spring 7 Brake chamber

2 Expander 8 Brake lining
3 Brake shoe 9 Anchor pin retainer
4 Anchor pin 10 Lock plate
5 Brake spider A Front
6 Brake drum
REAR
cardiagn.com
SHTS068020200306
1 Brake shoe return spring 7 Spring brake chamber

2 Expander 8 Brake lining
3 Brake shoe 9 Anchor pin retainer
4 Anchor pin 10 Lock plate
5 Brake spider A Front
6 Brake drum
SPECIAL TOOL
EN0680202K100005
Prior to starting a wheel brake overhaul, it is necessary to have these special tools.
09420-1510 ANCHOR PIN PULLER
cardiagn.com
COMPONENT LOCATOR
EN0680202D100024
FRONT
cardiagn.com
SHTS068020200308
1 Brake chamber 11 Brake shoe return spring

2 O-ring 12 Brake drum cover
3 Hole plug 13 Brake drum
4 Brake spider 14 Rivet
5 Anchor pin 15 Brake lining
6 Anchor pin retainer 16 Retainer spring
7 Lock plate 17 Return spring pin
8 Brake shoe assembly (Leading) 18 Bushing
9 Brake shoe assembly (Trailing) 19 Wheel sensor (If so equipped)
10 Expander 20 Sleeve (If so equipped)

A 35.8-51.4 {366-524, 26.4-37.9} D 20.1-33.9 {205-345, 14.9-24.9}
B 36.2-51.8 {370-528, 26.7-38.1} E 20.5-39.5 {210-402, 15.2-29.1}
C 14.1-23.9 {144-243, 10.4-17.6}
REAR
cardiagn.com
SHTS068020200309
1 Brake chamber 10 Expander 19 Sensor holder (If so equipped)

2 O-ring 11 Brake shoe return spring 20 Pivot pin
3 Hole plug 12 Brake drum cover 21 Washer
4 Brake spider 13 Brake drum 22 Cotter pin
5 Anchor pin 14 Rivet 23 Return spring hanger
6 Anchor pin retainer 15 Brake lining 24 Wheel sensor (If so equipped)
7 Lock plate 16 Retainer spring 25 Sleeve (If so equipped)
8 Brake shoe assembly (Trailing) 17 Return spring pin
9 Brake shoe assembly (Leading) 18 Bushing

A 35.8-51.4 {366-524, 26.4-37.9} D 20.5-39.5 {210-402, 15.2-29.1}
B 14.1-23.9 {144-243, 10.4-17.6} E 34.5-51.5 {352-525, 25.5-37.9}
C 20.1-33.9 {205-345, 14.9-24.9}
OVERHAUL
EN0680202H200023
1. REMOVAL OF TIRE
(1) Refer to chapter for WHEEL AND TIRE.
2. REMOVAL OF BRAKE DRUM, WHEEL HUB AND WHEEL HUB

BEARINGS
(1) Refer to chapter for FRONT AXLE and for REAR AXLE.
3. COMPRESSION OF SPRING IN SPRING BRAKE CHAMBER

BY RELEASE BOLT
(1) Remove the release bolt, washer and release nut from the cham-
ber.
SHTS068020200310
cardiagn.com
(2) Remove the end cap. Insert the release bolt to the brake cham-
SPRING BRAKE CHAMBER ber, then turn the release bolt by 1/4.
NOTICE
2
1 • Make sure that the release bolt can not be pulled out.
• When the release bolt is pulled out, insert the release bolt
again and turn it by 1/4 similarly.
RELEASE BOLT
END CAP
SHTS068020200311
(3) Apply compressed air of 640 kPa {6.5 kgf/cm2, 92.5 lbf⋅in.2} to the
spring brake port.
NOTICE
When compressed air cannot be applying, coat grease to the
release bolt.
(4) Install the washer and release nut to the release bolt and pull out
the release bolt by 85 mm {3.34 in.}.
NOTICE
Do not turn the release nut at the strong torque (68.6 N⋅m {700
kgf⋅cm, 50.6 lbf⋅ft} or more).
SHTS068020200312
4. REMOVAL OF BRAKE SHOE RETURN SPRING

(1) Using the special tool, remove the return spring.
(FRONT WHEEL)
SHTS068020200313
(2) Using the special tool, remove the outer return spring.
(REAR WHEEL)
SHTS068020200314
(3) Turn the pivot pin and pull out the return spring pin then remove
the inner return spring (REAR WHEEL).
cardiagn.com
SHTS068020200315
5. REMOVAL OF ANCHOR PIN

(1) Remove the lock plate and anchor pin retainer.
(2) Using the special tool, remove the pin and brake shoe assembly.
SST: Anchor Pin Puller (09420-1510)
SHTS068020200316
6. REMOVAL OF BRAKE CHAMBER AND EXPANDER

(1) Remove the air hose.
(2) Remove the brake chamber and O-ring from the brake spider.
(3) Using a hexagon wrench, remove the expander from the brake
spider.
SHTS068020200317
1. REPLACEMENT OF BRAKE LINING

(1) Remove the brake lining from the brake shoe.
a. Drill the rivet caulking section with a drill smaller than the rivet
diameter.
NOTICE
At this time, be careful not to scratch the brake shoe.
SHTS068020200264
b. After drilling, remove the remaining portion of the rivet with a

fine chisel or a riveting machine.
cardiagn.com
SHTS068020200265
(2) Install the brake lining to the brake shoe.

a. Set the lining on the shoe and insert the rivets into all holes,
then hold them in place with adhesive tape "A".
SHTS068020200267
b. Caulk the rivets lightly in a circular pattern as shown in figure

"B", repeat several times assure proper seating of the lining.
Recommended configuration of punch: shown in "C".
Recommended force of staking the rivet: 2.4 tons.
c. Remove adhesive tape.
SHTS068020200268
2. INSTALLATION OF EXPANDER AND BRAKE CHAMBER

(1) Apply grease (Darina Grease: Showa Shell Sekiyu K.K. product
or equivalent) to the expander as shown in the figure.
SHTS068020200318
(2) Using a hexagon wrench, install the expander to the brake spider.
Tightening Torque:
14.1-23.9 N⋅m {144-243 kgf⋅cm, 10.4-17.6 lbf⋅ft}
NOTICE
Pay attention to assembling way.
(3) Install the new O-ring and brake chamber to the brake spider.
cardiagn.com
SHTS068020200319
3. INSTALLATION OF BRAKE SHOE ASSEMBLY

(1) Apply adequate amount of heat resistance grease on the brake
LOCK WASHER
shoe bushing and anchor pin.
(2) Set the brake shoe assembly in place, then insert the anchor pins.
(3) Insert the anchor pin retainer in the grooves of the two anchor
pins.
(4) Place the lock plate on the anchor pin retainer so that its hole is
aligned with the lock plate hole, then insert the bolt and tighten it.
LOCK PLATE
SHTS068020200320
4. INSTALLATION OF BRAKE SHOE RETURN SPRING

(1) Hook the inner spring to the clamp and turn the pivot pin to align
the holes, then insert the spring hanger.
(REAR WHEEL)
NOTICE
Painted part of the spring must be placed in the upper side.
SHTS068020200315
(2) Use the special tool to install the return spring.

(FRONT WHEEL, REAR WHEEL OUTER SPRING)
NOTICE
The folded part of the spring cover must be placed in the upper
side.
SHTS068020200313
5. INSTALL THE WHEEL SENSOR. (IF SO EQUIPPED)

(1) Push in the clamping bushing until the stopper makes contact with
the wheel sensor holder.
(2) Push the wheel sensor forcefully into the clamping bushing until
you feel that the wheel sensor has contact with the sensor ring.
NOTICE
When inserting the wheel sensor, do not tap on it with a hammer
or attempt to pry it into place using a screwdriver, or the like.
Doing so could damage the wheel sensor.
cardiagn.com
(FRONT)
SHTS068020200321
(3) Arrange the wire harness.
(REAR)
SHTS068020200322
6. ASSEMBLE THE BRAKE DRUM AND WHEEL HUB.

(FRONT WHEEL)
(1) See the mark located at 1 or 1' on the brake drum as shown in fig-
ure. Install the drum according to NOTICE.
NOTICE
• The drums, number with R or L.
With R: Install in right side.
With L: Install in left side.
• The drums, with no R or L.
New drums: Install in any side.
Reused drums: Install in the side originally installed.
SHTS068020200285
(2) When assembling the brake drum and wheel hub, make sure that
their aligning marks are aligned as close to each other as possi-
ble.
NOTICE
Position of marks are located at 2 as shown in the figure. (Broken
line shows alternative position).

RELEASE
BOLT 1. REMOVAL OF THE RELEASE BOLT
FITTING
POSITION (1) After mounting, turn the release bolt counterclockwise to release
the spring brake.
NOTICE
Note the position mark R or L on the chamber which mark was
applied when dismounting and install it to its former side.
(2) After mounting, the release bolt must be set at the specified
torque.
Tightening Torque:
SHTS068020200323 13.7-15.7 N⋅m {140-160 kgf⋅cm, 10.2-11.5 lbf⋅in.}
2. MOUNTING OF WHEEL HUB AND BRAKE DRUM

(1) Refer to chapter for FRONT AXLE and for REAR AXLE.
NOTICE
1. Be careful not to push back the wheel sensor too far when
mounting the wheel hub and brake drum. Also, make sure
they are straight so that you do not bump the tip of the wheel
sensor.
2. When inserting the outer hub bearing, avoid tapping on it
with a hammer as this will expose the wheel sensor to
cardiagn.com
bumps. Insert the outer hub bearing carefully using a lock
nut.
(2) Slowly turn the wheel hub and brake drum and confirm that they
move smoothly.
3. MOUNTING OF TIRE
(1) Refer to chapter for WHEEL AND TIRE.
4. ADJUSTMENT
(1) Finally, adjust the brake shoe clearance as explained in Section
WHEEL BRAKE.
ADJUSTMENT
EN0680202H300028
1. REMAINING THICKNESS OF THE BRAKE LINING

(1) Check remaining thickness of lining through the inspection hole of
the brake drum cover. If the lining has been worn to the limit
marking or if it is foreseen that the lining will be worn to the limit by
the time the next inspection is made replace the lining.
SHTS068020200286
2. AIR PRESSURE IN THE AIR TANK

(1) Operate the engine and obtain an air pressure of the 740-840 kPa
{7.5-8.5 kgf/cm2, 107-121 lbf/in.2}
NOTICE
The specified air pressure in the air tank should be maintained
while making the adjustment.
cardiagn.com
3. INSPECTION OF THE CLEARANCE BETWEEN BRAKE LIN-
ING AND BRAKE DRUM
(1) Step on the brake pedal several times to make sure that the brake
shoes are correctly positioned.
SHTS068020200287
(2) Insert a thickness gauge from the inspection hole to inspect the
clearance between brake lining and brake drum. If the clearance
exceeds standard value, disassemble auto adjuster and perform
maintenance service because auto adjuster possibly may be out
of order.
STANDARD (mm {in.})

FRONT 0.2-1.0 {0.0079-0.0393}
REAR 0.2-1.0 {0.0079-0.0393}
4. ADJUSTMENT OF THE CLEARANCE BETWEEN BRAKE LIN-

ING AND BRAKE DRUM
NOTICE
As this brake has auto adjuster function, it is not necessary to
adjust the clearance between brake lining and brake drum. Adjust
the clearance in accordance with the following method, if the
brake lining is replaced and maintenance service is performed.
(1) Lift the wheel to be adjusted off the ground.
(2) While turning the wheel in the forward direction and step on the
brake pedal several times to make sure that the brake shoes are
correctly positioned.
SHTS068020200288 NOTICE
When adjusting the clearance between brake lining and brake
drum, set spring brake control valve to the OFF position.
(3) Remove the brake drum cover.

(4) Insert the thickness gauge and turn the adjusting screw with
screwdriver so that brake shoe clearance come to the standard
value.
SHTS068020200324
(5) While turning the wheel by hand in the forward direction, step on
the brake pedal several times to make sure that the brake shoes
are correctly positioned.
(6) See to it that there is no dragging, when turning the wheel by
hand. If there is any dragging, repeat the operation over again
from 2.
NOTICE
Using the same procedure as above, adjust the clearance for all
wheels.
cardiagn.com
SHTS068020200288

EN0680202H300029
Unit: mm {in.}
Brake drum: — — Regrind or Visual check

Cracks and damage replace,
if necessary.
Brake drum: 406.4 {16.0} Regrind Regrind or Measure

Inside diameter 409.4 {16.12} replace.
Service
410.4 {16.16}
cardiagn.com
Brake drum: 0-0.1 {0-0.0039} 0.2 {0.0079} Regrind or Measure
Runout replace.
Brake shoe assembly: — — Replace, Visual check

Cracks and damage if necessary.
Brake lining: 15.5 {0.610} 5.5 {0.217} Replace. Measure

Thickness
Clearance between brake 0.02-0.07 0.25 {0.0098} Replace the Measure

shoe bushing and anchor {0.0008-0.0027} brake shoe
pin bushing and/
or anchor
pin.
Brake shoe return spring — — Replace, Visual check

and spring cover: if necessary.
Damage, lacking elastic
strength distortion
EXPANDER
DESCRIPTION
EN0680202C100026
1 2
4
3
5
6
11 12 10 9
8
7
cardiagn.com
13
SHTS068020200331
1 Clip 8 E-retainer
2 Adjusting screw 9 Spring retainer
3 Boot 10 Wedge spring
4 Case 11 Retainer ring
5 Adjusting spring 12 Wedge
6 Drive ring 13 Body
7 Sleeve assembly
SPECIAL TOOL
EN0680202K100006
Prior to starting an expander overhaul, it is necessary to have these special tools.
09657-2330 GUIDE
cardiagn.com
09685-1020 BOOT SETTING TOOL
09659-1610 ADAPTER
COMPONENT LOCATOR
EN0680202D100025
cardiagn.com
SHTS068020200336
1 Clip 11 Retainer ring

2 Adjusting screw 12 Wedge assembly
3 Boot 13 Wedge boot
4 Case 14 Wedge cap
5 Adjusting spring 15 Wedge
6 Drive ring 16 Cage
7 Sleeve assembly 17 Roller
8 E-retainer 18 Expander body
9 Spring retainer 19 Locating screw
10 Wedge spring

A 12-18 {120-180, 9-13}
OVERHAUL
EN0680202H200024
1. DISASSEMBLY OF THE EXPANDER

(1) Remove the boot from the body.
(2) Turn the adjusting bolt counterclockwise and remove the boot
with adjusting bolt.
SHTS068020200337
(3) Remove the boot and retainer from the adjusting bolt.
NOTICE
When removing the retainer, take care not to damage it.
(4) Using the screwdriver, remove the cover and then remove the
adjust lock spring and adjust ring.
cardiagn.com
! WARNING
Pay attention to adjusting lock spring jump-out.
SHTS068020200338
(5) Remove the screw and then remove the sleeve assembly.
NOTICE
Sleeve assembly can not be disassembly.
SHTS068020200339
(6) Install the special tool to the body and tighten the bolt.
(7) Remove the E-ring.
(8) Remove the special tool and then remove the retainer, return
spring and wedge assembly.
! WARNING
Pay attention to return spring jump-out when removing the special
tool.
SHTS068020200340
2. DISASSEMBLY OF THE WEDGE ASSEMBLY

(1) Remove the retainer ring and then remove the boot, retainer and
HOLDER wedge assembly.
(2) Remove the holder and the roller from the wedge.
NOTICE
ROLLER Do not expand open end of holder 26 mm {1.023 in.} or more.
26 mm {1.023 in.}
SHTS068020200341
IMPORTANT POINTS - INSPECTION
1. INSPECTION FOR SLEEVE ASSEMBLY

(1) Fix the sleeve assembly in a vise and install the special tool to the
tappet part.
SST: Adapter (09659-1610)
(2) Install the torque wrench to the special tool to measure the start-
ing torque of the tappet part. Replace the sleeve assembly if the
cardiagn.com
torque exceeds the standard value.
Standard (N⋅m {kgf⋅cm, lbf⋅ft})

SHTS068020200342
Clockwise (Right turn) 0.6 {6.0, 0.433} or less
Counterclockwise (Left turn) 2.0 {20.0, 1.447} or more
2. INSPECTION FOR RETAINER KEEP TORQUE OF ADJUSTING

BOLT ASSEMBLY
(1) Fix the adjusting bolt fitted retainer in a vise and install the special
tool to clip.
NOTICE
Take care not to damage thread of the adjusting bolt when fixing
adjusting bolt in a vise.
SST: Adapter (09659-1610)
(2) Install the torque wrench to the special tool to measure the start-
ing torque of the retainer. Replace the adjusting bolt if the torque
SHTS068020200343 exceeds the standard value.
Standard: 2.0-5.5 N⋅m {20-55 kgf⋅cm, 1.45-3.97 lbf⋅ft}

HOLDER 1. ASSEMBLY OF THE WEDGE ASSEMBLY
(1) Assemble the roller to the holder and assemble them to the
wedge.
ROLLER NOTICE
Do not expand open end of holder 26 mm {1.023 in.} or more.
(2) Apply grease (Darina Grease 2: Showa Shell Sekiyu K.K. product
or equivalent) to engaged part and contact part of the roller,
holder and wedge.
26 mm {1.023 in.}
(3) Assemble the boot and retainer to the wedge, applying grease to
SHTS068020200341 wedge axle part and boot contact surface.
2. ASSEMBLY OF THE EXPANDER

(1) Fill up grease (Darina Grease 2: Showa Shell Sekiyu K.K. product
or equivalent) to the "A" part of body.
(2) Apply grease (Darina Grease 2: Showa Shell Sekiyu K.K. product
or equivalent) to the following part.
1. Adjust ring seat surface of body
2. Sleeve sliding part of body and tappet part stabbing part
3. Roller contact surface of tappet part and outer periphery
4. Sleeve assembly outer periphery and gear part
5. Sleeve assembly thread part.
SHTS068020200344
(3) Assemble wedge assembly to body, and install the new retainer
ring using the snap ring pliers.
(4) Install the return spring and then install the special tool.
(5) Install the new E-ring and remove the special tool.
cardiagn.com
SHTS068020200340
(6) After assembling the sleeve assembly to the body, tighten the
screw applied the LOCTITE 202 or ThreeBond 2415 or equiva-
lent.
NOTICE
Align the screw setting hole of body with the groove of tappet
part.
SHTS068020200339
(7) Install the adjust ring and adjust lock spring.

(8) Using the special tool, Install the cover.
NOTICE
• Be sure to install by hand using such as hammer.
• Before driving cover into sleeve assembly, assemble the
cover to the body groove.
• After assembling the cover, turn the cover while pushing it
and make sure that the cover turns smoothly in order to con-
firm the cover fits securely to the groove of the body.
SST: Guide (09657-2330)
SHTS068020200345
(9) Assemble the new boot to the adjusting bolt. Apply grease
(Darina Grease 2: Showa Shell Sekiyu K.K. product or equivalent)
to contact part of boot and adjusting bolt, and thread part of
adjusting bolt.
NOTICE
Be sure to assemble the boot to the groove of the adjusting bolt
securely.
SHTS068020200346
(10) Screw adjusting bolt into the sleeve assembly until the dimension
of end surfaces from adjusting bolt to body is about 20 mm {0.787
in.}.
(11) Pull the adjusting bolt lightly to confirm the sleeve slides.
(12) Using the plastic hammer and special tool, press a new boot in.
SST: Boot setting tool (09685-1020)
(13) Install the retainer to the adjusting bolt.

NOTICE
• Do not cut the boot.
• Pay attention to installing direction of the retainer.
SHTS068020200347

EN0680202H300030
Adjust lock spring: 78.3 N 73.6 N Replace. Measure

Setting load at the specified {8.0 kgf, 17.6 lbf} {7.5 kgf,
setting length at 11.3 {0.45} 16.5 lbf}
Return spring: 147 N 132 N
cardiagn.com
Setting load at the specified {15 kgf, 33.1 lbf} {13.5 kgf,
setting length at 105.8 {4.17} 29.8 lbf}
Sliding parts of sleeve — — Replace, Visual check

assembly and roller: if necessary.
Wear and damage
Axle dent of sleeve assembly — 0.010 mm Replace, Visual check

and roller: {0.0004 in.} sleeve
Wear and damage or less assembly or
roller.
Sliding parts of wedge and — — Replace, Visual check

roller: if necessary.
Wear and damage
Body inside diameter 38.05 mm 38.10 mm Replace. Measure

{1.498 in.} {1.5 in.}
or less
Sleeve assem- Clockwise 0.6 N⋅m — Replace. Measure

bly turning {6.0 kgf⋅cm,
torque 0.433 lbf⋅ft}
or less
Counter- 2.0 N⋅m

clockwise {20.0 kgf⋅cm,
1.447 lbf⋅ft}
or more
Retainer keep torque of 2.0-5.5 N⋅m — Replace. Measure

adjusting bolt assembly {20-55 kgf⋅cm,
1.45-3.97 lbf⋅ft}
cardiagn.com
PRESSURE REGULATOR
EN0680202I200025
Spring type, regulates air pressure together with

Type
unloader valve on compressor
Regulating pressure:
860-980 kPa {8.8-10.0 kgf/cm2, 125-142 lbf/in.2}
Regulator No. 44530-1420
DESCRIPTION
EN0680202C100027
1 Dust cover 7 Main spring 13 Valve spring

SHTS068020200352
cardiagn.com
2 Retainer ring 8 Valve rod 14 Filter
3 Adjusting screw 9 Rod spring 15 Piston
4 Lock nut 10 O-ring A To Unloader valve
5 Spring seat 11 Washer B From Air tank
6 Valve body 12 Valve seat C Exhaust
COMPONENT LOCATOR
EN0680202D100026
cardiagn.com
SHTS068020200353
1 Dust cover 6 Main spring 11 Valve seat

2 Adjusting screw 7 Valve rod 12 Valve spring
3 Lock nut 8 Washer 13 Filter
4 Retainer ring 9 O-ring 14 Rod spring
5 Spring seat 10 Piston 15 Valve body

A 2.4-3.5 {24-36, 1.8-2.6} B 0.29-0.49 {3-5, 0.22-0.36}
OVERHAUL
EN0680202H200025
1. LUBRICATION
(1) When reassembling the pressure regulator, replace all rubber
parts with new ones.
(2) Apply adequate amount of silicone grease to the O-rings, and
sliding surface S of the piston and valve rod.
cardiagn.com
SHTS068020200354
1. ADJUSTMENT
(1) Loosen the adjusting screw until the rod spring tension is
released, and start and idle the engine to charge the air for the air
tank.
SHTS068020200355
(2) Stop the engine when the gauge indicates valve opening pres-
sure shown below.
Valve opening pressure Pressure kPa {kgf/cm2, lbf/in.2}

44530-1420 940-980 {9.6-10.0, 136.3-142.1}
SHTS068020200356
(3) Tighten the adjusting screw gradually till the air starts to leak from
the port to the unloader valve side.
(4) Tighten the adjusting screw lock nut.
SHTS068020200357
(5) Watch the pressure gauge needle and see that it stops at the
valve closing pressure shown below.
(6) Connect the pipe and pressure regulator.
Valve closing pressure Pressure kPa {kgf/cm2, lbf/in.2}

44530-1420 820-860 {8.4-8.8, 118.9-124.7}
cardiagn.com
SHTS068020200358

EN0680202H300031
Valve body 1, piston 2 and — — Replace, Visual check

valve rod 3. Sliding surface: if necessary.
Valve rod 4.
Valve contact surface:
Wear and any other dam-
ages
Main spring 5. rod spring 6. — — Replace,

and valve spring 7: if necessary.
Rust and damage

Hino 700 Service Brake

Uploaded by

Copyright:

Available Formats

Hino 700 Service Brake

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hino 700 Service Brake

Uploaded by

Copyright:

Available Formats

SERVICE BRAKE BR02–1

AIR DRYER ...............................................BR02-3 PROTECTION VALVE (WITH 4-WAY

PROTECTION VALVE (TYPE-A) ............BR02-25 SPRING BRAKE CONTROL VALVE

RELAY VALVE (TYPE-B)........................ BR02-64 DESCRIPTION ...............................................BR02-95

REDUCING VALVE (TYPE-A) ................ BR02-70 TRAILER HAND BRAKE

Type Purge tank, desiccant, auto-purge valve.

Tightening torque Unit: N⋅m {kgf⋅cm, lbf⋅ft}

IMPORTANT POINTS - ASSEMBLY

IMPORTANT POINTS - MOUNTING

INSPECTION AND REPAIR

Inspection Item Standard Limit Remedy Inspection Procedure

Check valve and valve — — Replace, Visual check

Valve body sliding surface — — Replace, Visual check

Piston sliding surface: — — Replace, Visual check

Desiccant: — Discolored, Replace. Visual check

Type Spring type

1 Valve body 5 Body cap

1 Valve body 4 O-ring

Tightening torque Unit: N⋅m {kgf⋅cm, lbf⋅ft}

INSPECTION AND REPAIR

Inspection Item Standard Limit Remedy Inspection Procedure

Body cap: — — Replace, Visual check

DOUBLE CHECK VALVE

Type Piston type

1 Valve body 5 Plug

1 Valve body 4 Gasket

Tightening torque Unit: N⋅m {kgf⋅cm, lbf⋅ft}

IMPORTANT POINT - ASSEMBLY

INSPECTION AND REPAIR

Inspection Item Standard Limit Remedy Inspection Procedure

Valve and guide: — — Clean or replace, Visual check

Valve body and plug: — — Clean or replace, Visual check

Type Spring type

1 Valve 5 Compression spring

INSPECTION AND REPAIR

Unit: kPa {kgf/cm2, lbf/in.2}

Inspection Item Standard Limit Remedy Inspection Procedure

Valve opening pressure 1,029-1,068 — Replace. Measure

Type Dual pistons and valves with a plunger type pedal

1 Boot 16 Primary piston return spring

1 Stop lamp switch 10 Push rod

Tightening torque Unit: N⋅m {kgf⋅cm, lbf⋅ft}

1 Boot 16 Primary piston return spring

Tightening torque Unit: N⋅m {kgf⋅cm, lbf⋅ft}

IMPORTANT POINTS - DISMOUNTING

1. REMOVE THE CLUTCH MASTER CYLINDER.

2. DISCONNECT THE NYLON TUBE.

3. REMOVE THE PEDAL BRACKET ASSEMBLY.

4. REMOVE THE BRAKE PEDAL.

5. REMOVE THE BRAKE VALVE ASSEMBLY.

IMPORTANT POINTS - DISASSEMBLY

1. REMOVE THE PRIMARY PISTON ASSEMBLY.

2. REMOVE THE SECONDARY VALVE BODY.

3. REMOVE THE SECONDARY PISTON.

4. REMOVE THE PRIMARY FEED VALVE.

5. REMOVE THE EXHAUST PORT.

6. REMOVE THE SECONDARY FEED VALVE.

IMPORTANT POINTS - ASSEMBLY

2. ASSEMBLE THE STEM, SPRING, SPRING SEAT AND SHIM.

3. ALIGN THE VALVE COVER AND VALVE BODIES.