Hardness, Total DOC316.53.

01158

Titration Method with EDTA1,2 Method 8226

0–25,000 mg/L as CaCO3 Buret Titration
Scope and application: For water, wastewater and seawater.
1 USEPA accepted when 0.020 N titrant is used.
2 Adapted from Standard Methods for the Examination of Water and Wastewater.

Test preparation

Before starting
As an alternative to the ManVer 2 Hardness Indicator Powder Pillow, use 4 drops of Hardness 2 Indicator Solution or a 0.1-g
scoop of ManVer 2 Hardness Indicator Powder.
The optional TitraStir Titration Stand can hold the buret and stir the sample.
Review the Safety Data Sheets (MSDS/SDS) for the chemicals that are used. Use the recommended personal protective
equipment.
Dispose of reacted solutions according to local, state and federal regulations. Refer to the Safety Data Sheets for disposal
information for unused reagents. Refer to the environmental, health and safety staff for your facility and/or local regulatory
agencies for further disposal information.

Items to collect
Description Quantity

ManVer 2 Hardness Indicator Powder Pillow 1

Hardness 1 Buffer Solution 1 mL
TitraVer Hardness Titrant (use a concentration that is applicable to the selected sample
varies
volume)
Buret, Class A, 25 mL 1
Graduated cylinder (use a size that is applicable to the selected sample volume), or TenSette
1
pipet with tips
Erlenmeyer flask, 250 mL 1
Funnel, micro 1
Support stand with buret clamp 1
Water, deionized varies

Refer to Consumables and replacement items on page 7 for order information.

Sample collection and storage

• Collect samples in clean glass or plastic bottles that have been cleaned with a
detergent and rinsed with 1:1 nitric acid and deionized water.
• To preserve samples for later analysis, adjust the sample pH to 2 or less with
concentrated nitric acid (about 2 mL per liter). No acid addition is necessary if the
sample is tested immediately.
• Keep the preserved samples at or below 6 °C (43 °F) for a maximum of 7 days.
• Before analysis, adjust the pH to 7 with sodium hydroxide solution.
• Correct the test result for the dilution caused by the volume additions.

1
Test procedure

1. Select a sample volume 2. Fill a 25-mL buret to the 3. Use a graduated cylinder 4. Pour the sample into a
and titrant from Table 1 zero mark with the titrant. or pipet1 to measure the clean, 250-mL Erlenmeyer
on page 3. sample volume from Table 1 flask.
on page 3.

5. If the sample volume is 6. Add 1 mL of Hardness 1 7. Swirl to mix. 8. Add the contents of one
less than 50 mL, dilute to Buffer Solution. ManVer 2 Hardness
approximately 50 mL with Indicator Powder Pillow.
deionized water.

9. Swirl to mix. 10. Put the flask under the 11. Use the multiplier in
buret. Swirl the flask. Add Table 1 on page 3 to
titrant until the color calculate the concentration.
changes from red to pure mL of titrant × multiplier =
blue. mg/L total hardness as
CaCO3.

Sample volumes and multipliers

Select a range in Table 1, then read across the table row to find the applicable
information for this test. Use the multiplier to calculate the concentration in the test
procedure.

1 Titration accuracy has a direct relation to the accuracy of the sample volume measurement. For smaller
volumes, it is recommended to use a pipet to increase accuracy.

2 Hardness, Total (25,000 mg/L)

 Example: A 50-mL sample was titrated with 0.020 N titrant and 12 mL of titrant was used
at the endpoint. The concentration is 12 mL × 20 = 240 mg/L total hardness as CaCO3.
Table 1 Sample volumes and multipliers
Range (mg/L) Sample volume (mL) Titrant—TitraVer hardness Multiplier
0–500 50 0.020 N 20
400–1000 25 0.020 N 40
1000–2500 10 0.020 N 100
2000–5000 5 0.020 N 200
1000–5000 50 0.200 N 200
4000–10,000 25 0.200 N 400
10,000–25,000 10 0.200 N 1000

Conversions
To change the units or chemical form of the test result, multiply the test result by the
factor in Table 2.
Table 2 Conversions
mg/L as CaCO3 to... multiply by... Example
mg/L as Ca 0.40 1000 mg/L as CaCO3 x 0.40 = 400 mg/L Ca
mg/L as Mg 0.243 1000 mg/L as CaCO3 x 0.243 = 243 mg/L Mg
Grains per gallon (gpg) 0.058 1000 mg/L as CaCO3 x 0.058 = 58 gpg
German degrees hardness (Gdh) 0.056 1000 mg/L as CaCO3 × 0.056 = 56 Gdh

Interferences

WARNING
Chemical hazard. Potassium cyanide is toxic. Make sure to add potassium cyanide to the
sample after the Hardness 1 Buffer Solution has been added. Keep cyanide solutions at
more than pH 11 to prevent exposure to hydrogen cyanide gas. Dispose of reacted
solutions according to local, state and federal regulations.

An interfering substance can prevent the color change at the titration endpoint. A smaller
sample volume can often dilute the interfering substance to a level at which the
substance does not interfere. Table 3 shows the substances that can interfere with this
test.
Table 3 Interferences
Interfering Interference level
substance
Acidity 10,000 mg/L acidity as CaCO3 does not interfere.
Alkalinity 10,000 mg/L alkalinity as CaCO3 does not interfere.
Aluminum Interferes when the sample contains more than 0.20 mg/L aluminum. Add 0.5 grams of potassium
cyanide after the Hardness 1 Buffer Solution during the test procedure to remove the interference
from a maximum of 1 mg/L aluminum.
As an alternative, add a CDTA powder pillow to remove the interference. Refer to Use CDTA to
remove metal interferences on page 4.
Barium Barium is titrated at the same time with calcium and interferes with this test, but it is unusual to find
high levels of Barium in natural waters.
Chloride The chloride level in seawater does not interfere. Solutions that are saturated with chloride do not
show a sharp endpoint.

Hardness, Total (25,000 mg/L) 3

 Table 3 Interferences (continued)
Interfering Interference level
substance
Cobalt Interferes directly at all levels. Add 0.5 grams of potassium cyanide after the Hardness 1 Buffer
Solution during the test procedure to remove the interference from a maximum of 20 mg/L cobalt.
As an alternative, add a CDTA powder pillow to remove the interference. Refer to Use CDTA to
remove metal interferences on page 4.
Copper Interferes when the sample contains 0.1 mg/L copper. Add 0.5 grams of potassium cyanide after the
Hardness 1 Buffer Solution during the test procedure to remove the interference from a maximum of
100 mg/L copper.
As an alternative, add a CDTA powder pillow to remove the interference. Refer to Use CDTA to
remove metal interferences on page 4.
Iron More than 8 mg/L iron causes an orange-red to green endpoint. Results are accurate to 20 mg/L iron
with this endpoint. For more accurate endpoints in solutions that have higher levels of iron, use
HexaVer Hardness Titrant (CDTA) and not TitraVer Hardness Titrant (EDTA).
Manganese Interferes when the sample contains more than 5 mg/L manganese. Add a 0.10-gram scoop of
Hydroxylamine Hydrochloride Monohydrate to increase the interference level to 200 mg/L
manganese.
Nickel Interferes directly at all levels. Add 0.5 grams of potassium cyanide after the Hardness 1 Buffer
Solution during the test procedure to remove the interference from a maximum of 200 mg/L nickel.
As an alternative, add a CDTA powder pillow to remove the interference. Refer to Use CDTA to
remove metal interferences on page 4.
Orthophosphate Forms calcium phosphate and causes a slow endpoint. If sufficient time is given to let the calcium
phosphate dissolve during the titration, the orthophosphate will not interfere with the test.
Polyphosphates Interferes at all levels.
Polyvalent metal ions Although less common than calcium and magnesium, other polyvalent metal ions are titrated with the
calcium and magnesium and are included in the results.
Strontium Strontium is titrated at the same time with calcium and magnesium and interferes with this test, but it
is unusual to find high levels of Strontium in natural waters.
Zinc Interferes directly and is included in the test result. Add 0.5 grams of potassium cyanide after the
Hardness 1 Buffer Solution during the test procedure to remove the interference from a maximum of
100 mg/L zinc.
As an alternative, add a CDTA powder pillow to remove the interference. Refer to Use CDTA to
remove metal interferences on page 4.
Highly buffered Can prevent the correct pH adjustment (of the sample) by the reagents. Sample pretreatment may
samples or extreme be necessary. Before analysis, adjust the pH to 7.
sample pH

Use CDTA to remove metal interferences

Add one CDTA Magnesium Salt Powder Pillow to remove the interference from metals at
or below the levels shown in Table 4. If more than one metal is in the sample at or more
than the concentration in Table 4, add an additional CDTA Magnesium Salt Powder
Pillow.
The results given with CDTA Magnesium Salt include the hardness from these metals. If
the concentration of each metal is known, a correction can be made to get the hardness
from calcium and magnesium only. The hardness value from different metal ions is shown
in Table 5.
Metal hardness = (mg/L of metal in the sample) x (hardness equivalence factor)
Calcium and magnesium hardness = (total hardness) – (metal hardness)

4 Hardness, Total (25,000 mg/L)

 Table 4 Interference level with one CDTA pillow
Interfering substance Interference level
Aluminum 50 mg/L
Cobalt 200 mg/L
Copper 100 mg/L
Iron 100 mg/L
Manganese 200 mg/L
Nickel 400 mg/L
Zinc 300 mg/L

Table 5 Hardness equivalence factors (mg/L as CaCO3)

Interfering substance Hardness equivalence factor
Aluminum 3.710
Barium 0.729
Cobalt 1.698
Copper 1.575
Iron 1.792
Manganese 1.822
Nickel 1.705
Strontium 1.142
Zinc 1.531

Accuracy check
Standard additions method (sample spike)—0.020 N titrant
Use the standard additions method to validate the test procedure, reagents, apparatus,
technique and to find if there is an interference in the sample.
Items to collect:
• Calcium Hardness Standard Solution, 10,000 mg/L as CaCO3, 10-mL Voluette
ampule
• Ampule Breaker
• Pipet, TenSette, 0.1–1.0 mL and pipet tips

1. Use the test procedure to measure the concentration of the standard solution. Use
the 0.020 N titrant.
2. Use a TenSette pipet to add 0.1 mL of the standard solution to the titrated sample.
3. Titrate the spiked sample to the endpoint. Record the mL of titrant added.
4. Add one more 0.1-mL addition of the standard solution to the titrated sample.
5. Titrate the spiked sample to the endpoint. Record the mL of titrant added.
6. Add one more 0.1-mL addition of the standard solution to the titrated sample.
7. Titrate the spiked sample to the endpoint. Record the mL of titrant added.
8. Compare the actual result to the correct result. The correct result for this titration is
1.0 mL of titrant for each 0.1-mL addition of the standard solution. If much more or
less titrant was used, there can be a problem with user technique, reagents,
apparatus or an interference.

Hardness, Total (25,000 mg/L) 5

Standard additions method (sample spike)—0.200 N titrant
Use the standard additions method to validate the test procedure, reagents, apparatus,
technique and to find if there is an interference in the sample.
Items to collect:
• Calcium Hardness Standard Solution, 10,000 mg/L as CaCO3, 10-mL Voluette
ampule
• Ampule Breaker
• Pipet, TenSette, 0.1–1.0 mL and pipet tips

1. Use the test procedure to measure the concentration of the standard solution. Use
the 0.200 N titrant.
2. Use a TenSette pipet to add 1.0 mL of the standard solution to the titrated sample.
3. Titrate the spiked sample to the endpoint. Record the mL of titrant added.
4. Add one more 1.0-mL addition of the standard solution to the titrated sample.
5. Titrate the spiked sample to the endpoint. Record the mL of titrant added.
6. Add one more 1.0-mL addition of the standard solution to the titrated sample.
7. Titrate the spiked sample to the endpoint. Record the mL of titrant added.
8. Compare the actual result to the correct result. The correct result for this titration is
1.0 mL of titrant for each 1.0-mL addition of the standard solution. If much more or
less titrant was used, there can be a problem with user technique, reagents,
apparatus or an interference.

Standard solution method—0.020 N titrant

Use the standard solution method to validate the test procedure, reagents, apparatus and
technique.
Items to collect:
• Calcium Chloride Standard Solution, 1000 mg/L as CaCO3
• Pipet, TenSette, 1.0–10.0 mL and pipet tips

1. Use the test procedure to measure the concentration of the standard solution. Use
25.0 mL of the standard solution and the 0.020 N titrant.
2. Compare the actual result to the correct result. The correct result for this titration is
25 mL of titrant.

Standard solution method—0.200 N titrant

Use the standard solution method to validate the test procedure, reagents, apparatus and
technique.
Items to collect:
• Calcium Hardness Standard Solution, 10,000 mg/L as CaCO3, 10-mL Voluette
ampule
• Ampule Breaker
• Pipet, TenSette, 1.0–10.0 mL and pipet tips

1. Use the test procedure to measure the concentration of the standard solution. Use
10.0 mL of the standard solution and the 0.200 N titrant.
2. Compare the actual result to the correct result. The correct result for this titration is
10 mL of titrant.

Summary of method
A buffer solution (an organic amine and one of its salts) is added to the sample to adjust
the pH to 10.1. An organic dye, calmagite, is then added as the indicator for the test. The
organic dye reacts with calcium and magnesium ions to give a red-colored complex. The
EDTA (ethylenediaminetetraacetic acid) titrant is added, which reacts with all of the free
calcium and magnesium ions in the sample. After the EDTA has reacted with all of the

6 Hardness, Total (25,000 mg/L)

 free magnesium ions, the EDTA removes the magnesium ions from the indicator. The
indicator color then changes from red to blue.
Consumables and replacement items
Required reagents

Description Quantity/Test Unit Item no.

Hardness (Total) Reagent Set (approximately 100 tests): — each 2447600

ManVer 2 Hardness Indicator Powder Pillows 1 pillow 100/pkg 85199
Buffer Solution, Hardness 1 1 mL 1L 42432
®
TitraVer Hardness Titrant, 0.020 N varies 1L 20553
Hardness (Total) Reagent Set (approximately 100 tests): — each 2447700
ManVer 2 Hardness Indicator Powder Pillows 1 pillow 100/pkg 85199
Buffer Solution, Hardness 1 1 mL 1L 42432
®
TitraVer Hardness Titrant, 0.200 N varies 500 mL 102149

Required apparatus

Description Quantity/test Unit Item no.

Buret clamp, double 1 each 32800

Buret, Class A, 25 mL 1 each 2636540
Support stand 1 each 56300
Funnel, micro 1 each 2584335
Graduated cylinders—Select one or more for the sample volume:
Cylinder, graduated, 5 mL 1 each 50837
Cylinder, graduated, 10 mL 1 each 50838
Cylinder, graduated, 25 mL 1 each 50840
Cylinder, graduated, 50 mL 1 each 50841
Cylinder, graduated, 100 mL 1 each 50842
®
Tensette pipets and pipet tips—Select one or more for the sample volume:
®
Pipet, TenSette , 0.1–1.0 mL 1 each 1970001
®
Pipet tips, TenSette Pipet, 0.1–1.0 mL varies 50/pkg 2185696
®
Pipet, TenSette , 1.0–10.0 mL 1 each 1970010
®
Pipet tips, TenSette Pipet, 1.0–10.0 mL varies 50/pkg 2199796
Flask, Erlenmeyer, 250 mL 1 each 50546

Recommended standards

Description Unit Item no.

Calcium Chloride Standard Solution, 1000 mg/L as CaCO3 1L 12153

Calcium Hardness Standard Solution, 10,000 mg/L as CaCO3, 10-mL Voluette ampule 16/pkg 218710

Hardness, Total (25,000 mg/L) 7

Optional reagents and apparatus

Description Unit Item no.

®
Ampule Breaker, 10-mL Voluette Ampules each 2196800
CDTA Magnesium Salt Powder Pillow 100/pkg 1408099
Delivery tube for Digital Titrator, 90-degree bend for use with TitraStir Titration Stand 5/pkg 4157800
ManVer Hardness Indicator Solution 100 mL 42532
ManVer 2 Hardness Indicator Powder 113 g 28014
Nitric Acid, concentrated 500 mL 15249
Nitric Acid Solution, 1:1 500 mL 254049
Potassium Cyanide, ACS 100 g 76714
Bottle, sampling, with cap, low density polyethylene, 250 mL 12/pkg 2087076
Sodium Hydroxide Solution, 5 N 50 mL 245026
Spoon, measuring, 0.1 g each 51100
Spoon, measuring, 0.5 g each 90700
Stir bar, octagonal each 2095352
TitraStir® Titration Stand, 115 VAC each 1940000
TitraStir® Titration Stand, 230 VAC each 1940010

FOR TECHNICAL ASSISTANCE, PRICE INFORMATION AND ORDERING: HACH COMPANY

In the U.S.A. – Call toll-free 800-227-4224 WORLD HEADQUARTERS
Outside the U.S.A. – Contact the HACH office or distributor serving you. Telephone: (970) 669-3050
On the Worldwide Web – www.hach.com; E-mail – [email protected] FAX: (970) 669-2932

© Hach Company/Hach Lange GmbH, 2007–2015. All rights reserved. 05/2015, Edition 8