TELESCOPIC BORESCOPE
eheV2-USB-T
USER’S MANUAL
Introduction
Functions and applications
The TELESCOPIC BORESCOPE is a new electronic product for the industry
inspections. It is a telescopic imaging system consisting of an optical lens, an image
sensor, an illumination mechanism, and an image transfer control circuit connected
to a computer. User can display the images captured by the TELESCOPIC
BORESCOPE on the computer screen, store them on the computer, print them, or
send them over the Internet.
The TELESCOPIC BORESCOPE can be used at different lengths by pull out or
draw back the telescopic tubing. And also can change the adapters that attached with
this borescope for different purposes.
As a TELESCOPIC BORESCOPE, it can be used to inspect the inside of
engines, machines, tubing and so on. And also it can be used as a USB pen style
microscope to magnify stamps, coins, antiques, insects, electric circuits, machines,
fabrics, food, decorations, etc.
Attention
Before use of this product, please read the instructions in this manual to ensure
its correct use.
Safety instructions
Before using this product, please carefully read the following safety instructions.
1. The socket that the computer is plugged in must be properly grounded, as the
computer supplies power to this product. If in any doubt, please have a professional
electrician check and verify the grounding to ensure safety.
2. Never use this product in stormy weather.
3. This product contains delicate and precision components. Be gentle when using
it and avoid harsh handling or excessive force that may cause damage to the product.
4. The temperature of the handle increases slightly during use and it feels a little
warm. This is normal. If the product is overheated and hot to the touch, immediately
cut off the power and contact us for repair.
5. Never leave the product on unattended. Unplug from the USB port after use.
6. Do not disassemble this product. Disassembling this product will result in
irreparable damage. The company is not responsible for damage resulting from
disassembly of the product by the user. In case of any difficulties in using the
product, please contact us.
7. This product may only be used by children under supervision of an adult. Never
give this product to a child to use or play by him or herself. Keep this product out of
reach of children.
8. Do not let this product come in direct contact with steam, vapor, water, or
liquids of any kind. Such contact can cause irreparable damage that is not covered
by warranty.
9. When not in use, put the handle in the transparent sleeve and store it in a tightly
sealed box to avoid moisture and decay. Damages resulting from improper storage
are not covered by the warranty.
10. Never use this product to examine the eyes.
11. Examination or cleaning of the ear canal, nasal cavity and oral cavity should
only be undertaken by adults who have mastered the depth and force required for
such a task.
12. The cable in this product have been strictly tested. To ensure safe use, do not
replace it.
System Requirements
For best picture quality, the following specifications are recommended:
1. Windows XP，Vista or 7.
2. At least 3 USB ports (For best effect, USB 2.0 port is recommended).
Technical Specifications
1. DSP: High Quality Digital Image Monarch Processor.
2. Sensor: high-quality CMOS sensor
3. Resolution: 1280X1024
4. Interface: USB2.0.
5. Frame rate: 30 frames/sec (CIF and VGA).
6. Focal distance: 10mm - infinity
7. Magnification: 1× to 100× adjusable
8. Length and Diameter( in millimeter):
SECTIONS 1 2 3 4 5 TOTAL
LENGTH 130 113 113 112 132 605
DIAMETER 8.03 9.03 10.03 11.03 12.15 -
LENGTH in full pull out situation: 605mm
LENGTH in draw back situation: 155mm
10. USB cable length: 4.4 meters at the full pull out situation
Packing List
ITEM QTY.
TELESCOPIC BORESCOPE 1
CURETTE 1
REFLECTOR TUBE 1
RUBBER SLEEVE 1
TRIPOD 1
CD 1
MODEL PACKAGE ITEM USB
SIZE 20 X 14 X 7
GIFT BOX QTY 1
WEIGHT 310g
eheV2-USB-T
SIZE 55 X 40 X 40
CARTON BOX QTY 40
WEIGHT 17Kg
SIZE SCALE: centimeters
Package Box
The package may be changed without notice.
Directions for Use
Properly connect the
TELESCOPIC
BORESCOPE to the
computer USB PORT and
to rotate the DIMMER on
the USB cable to controls
the brightness of the LEDs
on the TELESCOPIC
BORESCOPE.
Double click on the
icon of “My PC” on the computer desktop and then double click on the icon of
‘Camera’. After a short while you should see the image captured by the
TELESCOPIC BORESCOPE on the computer monitor.
Or user may find the software in the CD that is come with TELESCOPIC
BORESCOPE in the box. The software named ‘ehe.exe’ you should copy it (JUST
COPY NOT INSTALL) from the CD into your computer. And then double click on
the icon to RUN the software (without any installing procedure).
OPEN IMAGE WINDOW
Double click on the icon ‘ehe.exe’ and open an image window on the screen.
After a few seconds the TELESCOPIC BORESCOPE will begin to take still image
in the window.
Click on ‘OPTIONS’ and click on ‘VIDEO CAPTURE PIN’ on the top line of
the image window. Click one of image window size in the drop-down menu and
click on ‘OK’ to confirm. The 640 X 480 is recommended.
FOCUSING
The focus distance is already fixed on the 30mm from lens surface to
the objective you want to magnify by the TELESCOPIC BORESCOPE .
User may slightly rotate the focusing ring that located on the top of
TELESCOPIC BORESCOPE for adjusting the focal distance. Please pay
attention to that any of
rough operation or over
focusing adjustment will
cause damage of
TELESCOPIC
BORESCOPE.
Please ask us for a
help on any focusing
distance adjustment.
USE RUBBER SLEEVE
First of all, focus the
image of the TELESCOPIC
BORESCOPE at the proper
distance that you feel the
magnification is satisfied. Put
the rubber sleeve on the top of
TELESCOPIC BORESCOPE
and to adjust the sleeve to a
position that the focus point is
at little bit of inner place of the sleeve. While you are using the TELESCOPIC
BORESCOPE you may touch the objective with the end of sleeve and slightly
push the sleeve down to find
the clear focused image. This is
what we called “soft
focus(SF)”.
By using the SF you can
look into a small hole or slit by
focusing on many different
distance levels.
SF can be used for the
inspection of electronic parts, machine parts, skin, hair and so on.
PULL OUT AND DRAW BACK
See follow photos to pull out and draw back the TELESCOPIC BORESCOPE.
Hold two ends of the TELESCOPIC
BORESCOPE to pull it out slightly.
User may pull half or any length you
want to get any length of the borescope
for proper inspection.
User may adjust the length of every
section by pull it out or draw it back.
Total is 605mm in length by pulling all
of the sections out.
For draw back the sections, hold the
last section by the left hand and right
hand pull the USB cable slightly to get the section draw back.
Should be slightly and slowly draw
back the sections.
REFLECTOR TUBE
Reflector tube is
used for side view of
any tubing inspection.
For the side view
the TELESCOPIC BORESCOPE should be focused on any surface that is at
the distance of 10mm to
100mm far from the opening of
the reflector before it be put
into a tubing.
Take the reflector tube
out of the peel pouch and put it
on the TELESCOPIC
BORESCOPE like the photo
shows.
Push the reflector tube to the end all the way and turn a little bit to
confirm it is well fixed. Please pay much attention to this procedure to avoid
the tube falling off during the use.
CURETTE
By using the curette user
can look into tubing or tank to
scratch the surface for rusting
inspections. Put the curette on the
top of the TELESCOPIC
BORESCOPE (see the left photo) and
focus on the end of the small scoop.
TAKE PHOTOS
Push down the snap key on the handle or push down
the button of the dimmer that located on the USB
cable to freeze an image. Or click ‘snap’ on the top
of image window, or push down the ‘return key’ of
keyboard to take a photo.
The photos you have taken will be saved in the
computer and display an icon on the screen.
If your system could not freeze an image please
follow steps to make it works:
1, click on ‘file’ that is on the top of image window.
2, click on the ‘set photo folder’
3, designate the folder you want to save the photos
4, click OK to confirm
IMAGE FREEZ
Please rap the space bar for freezing an image and rap again to activate the
image.
TIMING SNAP
Rap the F5 key to arouse a timing snap.
The snap will be delayed 10 seconds after the key was rapped company with beep
per second.
If you could not get a clear photo by push down the snap button the timing snap
may be a help.
WARNING
The top line of the image window will be blue color while it works properly. It
will be changed into light blue when user operates on background and the snap
function will be lost during this color.
Just click any where inside of the image window to change it back to blue.
MOVIE RECORD
For taking a video:
1, click on ‘video capture’
2, click on ‘Set Time Limit’ and input how many seconds the video you want to
take and tick the ‘use time limit’
3, click on the ‘capture’ again
4, click on ‘start capture’
5, click on ‘OK’ to start a record
The video will be taken and stopped automatically when time out.
The video is an AVI format.
User may move the AVI file to any folder like other documents.
TRIPOD
User may feel hand shake while
using the TELESCOPIC BORESCOPE
especially when taking photos. The
tripod can be a very good help.
The tripod can be adjusted to many
directions and locked for the stable
photos and videos.
Post-Sale Services
Limitations and exclusions
Please keep all the receipts of your purchase in a safe place. You need to produce the
unaltered and original receipts to receive warranty coverage. Otherwise, the
warranty is voided.
The warranty only covers the product if it is used under normal operation conditions.
However, the following are not covered by the warranty:
Damages resulting from unauthorized disassembly or assembly of the products by
the customer
Damages caused by fitting of improper components to the product
Damages resulting from unauthorized attempts to repair or to alter the product
Gross distortion, scratches, discoloration, or damage of the covering
Cracks, scratches, and mold spots on the lens
COMS sensor is burned or apparently scratched
Damages to the PCB board (such as burned PCB board) due to misuse
Repair Service Card
Product model:
Date of repair
Customer’s name
phone number
Description of faults
Place of repair
Results
Warranty Card
Name of customer Address of customer
Purchase date Customer phone number
Labeling of Sales Company
Product model
Serial number
