Scribd
Upload
512 views3 pages

ZTE Notes

This document contains configuration commands for a ZTE OLT, including commands to clear an ONU configuration, add/remove IP addresses from VLANs, check interfaces, routes, VLAN configurations, ONU profiles, optical power levels, and more. It also includes instructions for remotely accessing ONUs via web or telnet, checking performance and real-time data, adding/deleting cards, changing WiFi SSIDs, searching for ONUs, and viewing alarms.

Uploaded by

Myo Zaw Oo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
512 views3 pages

ZTE Notes

This document contains configuration commands for a ZTE OLT, including commands to clear an ONU configuration, add/remove IP addresses from VLANs, check interfaces, routes, VLAN configurations, ONU profiles, optical power levels, and more. It also includes instructions for remotely accessing ONUs via web or telnet, checking performance and real-time data, adding/deleting cards, changing WiFi SSIDs, searching for ONUs, and viewing alarms.

Uploaded by

Myo Zaw Oo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 3

zte notes

=========

-clear onu config

conf t
interface gpon-onu_1/2/1:3
clear
*only serial number left(no need to re-add onu)*
====================================================
-to add ip in vlan 1000

conf t
#interface vlan 1000
#ip address 192.168.100.11 255.255.255.0
====================================================
-to remove ip in vlan 1000

#conf t
#interface vlan 1000
#no ip address
====================================================
-to check vlan ip

#show ip interface bri


====================================================
-to check ip route

#show ip route
====================================================
-to check gpon vlan

#show run | begin gpon


====================================================
-to check vlan database

#show run | begin vlan database


=====================================================
-to check gpon traffic

#show gpon profile traffic (or) tcont


=====================================================
-to check onu profile vlan

#show gpon onu profile vlan


=====================================================
-to check onu optical power

#show pon power attenuation gpon_onu_1/2/1:1


=====================================================
-to check onu wan ip

#show gpon remote-onu wan-ip gpon-onu_1/2/1:1


=====================================================
-to enter with wifi or remote

#ip route 0.0.0.0 0.0.0.0 172.18.6.2


=====================================================
-to check snmp

#show snmp config


=====================================================
-to autosave the config

#auto-write enable
#auto-write 12:00:00 everyday
=====================================================
-to enter onu remote by web

#pon-onu-mng gpon-onu_1/2/1:1
#security-mgmt 1 state enable mode forward ingress-type wan protocol https
#security-mgmt 1 state enable mode discard ingress-type wan protocol https (to
shutdown)
#show gpon remote-onu wan-ip gpon-onu_1/2/1:1 (check onu ip)

in web https://ip
============================================================
-to enter onu remote by telnet

#pon-onu-mng gpon-onu_1/2/1:1
#security-mgmt 1 state enable mode forward ingress-type wan protocol telnet
#security-mgmt 1 state enable mode discard ingress-type wan protocol telnet (to
shutdown)

telnet onu ip
login-root
password-Zte521
============================================================
-to check MTU

#show eth-switch
======================================================
-to add new card

#add-card slotno 9 GUFQ


======================================================
-to check interface

#show interface gei_1/19/1


#show interface vlan 1102
======================================================
-to check smartgroup bandwidth

#show interface smartgroup


(BW 200000000 kb)
======================================================
-to check battery percentage (in ems)

R.click on olt/ System Management/ Environmental Power Monitor/


Rated Capacity or Remaining Capacity
======================================================
-to check onu real time performance

Performance/ Real Time Performance Data Monitoring/


Select Indices (Rx/Tx Octet Rated(bps))
Select Locations (ONU ID)
======================================================
-to delete/add card

#del-card slotno 6
#add-card slotno 6 GTGH
======================================================
-to change ssid name

#pon-onu-mng gpon-onu_1/2/1:1
ssid ctrl wifi_0/1 name testssid1

ssid auth wpa wifi_0/1 wpa2-psk key 12345678

interface wifi wifi_0/2 state unlock (for SSID 2,3,4)


======================================================
-to search onu by name

r.click on olt/search onu/onu name/S121200232


======================================================
-to check onu detail

#show gpon detail


======================================================
-to check uplink power

show interface optical-module-info gei_1/19/1


======================================================
-to check onu config

show onu running config gpon-onu_1/2/3:2


======================================================
-to check protocol

show ip interface bri


======================================================
-to check alarm

show alarm pool


======================================================

You might also like