How To Build A DIY Awning

How to Build a DIY Awning
Written by
James Fitzgerald
Published 08/03/21
 Pin
 Share
 Email
poplasen / Getty Images
Overview
 Working Time: 4 - 8 hrs

 Total Time: 1 - 2 days
 Skill Level: Intermediate

 Estimated Cost: $100 to $300
Serving as both a functional shade covering and an attractive design feature, an awning can make a lovely
contribution to any outdoor living space. Unfortunately, it can also be expensive to purchase and install. That is,
unless you build one yourself.
Building a DIY awning gives you the freedom to customize the design features while constructing an awning to
the exact specifications you desire. Most notably, you get to choose among a variety of covering materials, such
as awning fabric, corrugated plastic, and corrugated metal.
If you're interested in making an attractive and affordable awning with minimal time and effort, read on to learn
how it's done.
Safety Considerations
Building an awning requires the use of power tools, including a miter saw. You should only attempt this project
if you know how to safely handle these tools, and if you possess the necessary safety equipment. Always wear
eye and hearing protection.
This project may also involve the use of a ladder, depending on how high your awning is going to be placed.
Again, you should only attempt this project if you can safely and effectively work off a ladder. Consider
recruiting a helper to stabilize the ladder while you’re working, and to be on hand to call for help in case of an
accident or emergency.
What You'll Need

Equipment / Tools
 Miter saw
 Tape measure
 Carpenter's pencil
 Speed square
 Framing square
 Caulking gun
 Power drill
 Impact Driver
 Spirit level
 Hearing protection
 Safety glasses
Materials
 Exterior-grade 2x4 lumber (cedar, pine, or redwood)

 3-inch exterior-grade structural screws
 2 1/2-inch exterior-grade structural screws
 4-inch lag bolts
 6-inch lag bolts
 Exterior caulking
 Exterior-grade wood filler (optional)
 Paint and primer or wood stain (optional)
Instructions
1. Locate Wall Studs
The awning will have one board attached to the wall (ledger board) along with two diagonal braces that
run from the wall to the front of the awning. All three of these pieces need to be anchored to a wall stud
for sufficient structural support.
Locating these studs on the exterior wall of your home can be tricky, since conventional methods—like
using a stud finder—won’t work through exterior siding.
The best ways to find and mark the stud locations on your exterior wall is by:
o Locating the studs from the interior wall, and transferring those measurements outside.
o Using standard framing layouts and building component reference points. Most studs are located
16 inches away from one another, but older homes may have a 24-inch framing layout. Building
components like doors, windows, and walls have framing members surrounding and supporting
them which can often be measured off of to find surrounding studs. Exterior electrical outlets can
also be measured from, since they’re attached to the side of a stud.
o Siding nail and seam locations. The nail heads used to secure siding to the exterior wall are often
visible through the paint. If you see a vertical row of nail heads on your siding, there may be a
stud behind it. Visible seams where two pieces of siding meet—especially when combined with
a vertical row of nails—is another good indicator. However, this isn’t the most reliable method,
since some siding is “blind nailed,” which conceals the nail heads.
Mark the stud locations on your siding with a carpenter’s pencil throughout the entire length of the area
the awning will cover. Verify the presence of a stud by drilling a small hole through the siding. It’s best
to drill in the spot you’re going to install your awning, since the holes will get covered by the ledger
board. Otherwise, the holes can be patched by exterior-grade wood filler and painted over.
2. Measure the Awning's Width
Determine the length of your ledger board by measuring the width of the area you want to cover with the
awning. Measure from stud to stud. Since your diagonal braces need to be secured to a stud on one end,
and to the inside surface of an end rafter on the other end, add three inches to this measurement to
account for both end rafters. Otherwise, each diagonal brace will miss the wall stud by the width of the
rafter, or 1 1/2 inches.
Next, measure from the wall to the farthest point you want the awning to cover. This will be the size of
your rafters.
3. Cut the Ledger and Fascia Board to Length
Use a miter saw to cut two 2x4s to the length you obtained in the last step. One will be the ledger board,
and the other will be the fascia board—the outward facing vertical board on the opposite end of the
ledger board.
4. Mark the Rafter Layout
Ideally, your awning should have evenly spaced rafters at least every 24 inches. Subtract 1 1/2 inches
from your ledger board length to account for the outside rafters, and divide that figure—in inches—by
24 to determine how many inside rafters you’ll need. If the sum isn’t a whole number, round it up or
down to the nearest whole number. For example, a 66-inch board divided by 24 inches is 2.75, which
rounds up to 3. Combined with the two outside rafters, you end up with a total of 5 rafters.
Next, divide the number of rafters by the length of the ledger board to determine the distance between
rafters. For a 66-inch ledger board, the distance between your rafters is 22 inches (66 / 3).
Place the end of your tape measure on the end of the ledger board and mark out the distance between the
rafters with a carpenter’s pencil. Use a speed square to mark a straight line through this mark, and mark
an X on the outside—on the opposite side you’re pulling the tape measure from—of the line. That will
be where the end of your rafters go.
Lay ledger board and fascia board edge to edge, and transfer the marks from the ledger board onto the
fascia board with a framing square. Finally, transfer the measurements of your wall studs onto the center
of the ledger board.
5. Cut the Rafters to Length
Cut the rafters to length with a miter saw.
6. Make the Diagonal Braces
Place the end of one rafter board flush to the outside surface of the ledger board. Screw two 3-inch
structural screws through the back of the ledger board into the end of the rafter. Repeat on the other end
of the ledger board.
Secure the inside rafters to the ledger board by holding them flush onto the layout marks you made, and
drive two 3-inch structural screws into each.
Once all the rafters are in place, place the other end of the rafters onto the corresponding layout marks
on the fascia board. Secure two 3-inch structural screws through the fascia into the end of each rafter.
7. Assemble the Frame
Using one or more helpers, hold the frame’s ledger board on the wall where the awning will be installed.
Line up the stud marks on the ledger board to the stud marks on the wall. Starting at one end of the
awning, drill a 4-inch-deep pilot hole through the ledger board and into the wall on the mark you made
for the stud location. Use an impact driver to drive a 4-inch lag bolt into the pilot hole.
Use a spirit level to verify the ledger board is level, and drive another lag bolt into the opposite end of
the board. Then, drive lag bolts into each of the remaining stud marks on the inside of the ledger board.
8. Hang the Awning Frame
Use your miter saw to cut 45-degree angles (miters) on one end of two 2x4s. Hold the mitered end of
one of the braces flush to the wall, below one of the outside rafters. Hold the other end of the brace
against the inside surface of the rafter. For optimal structural integrity, the top end of the brace should be
secured as close as possible to the fascia board on the front of the awning.
Using the top edge of the rafter as a guide, mark a straight line on the surface of the diagonal brace
where it meets the rafter. Once the brace is cut at this mark, the end of the brace should be flush with the
top edge of the rafter. Repeat this step on the other side for the second brace.
Use a miter saw to cut the brace at the marks you made.
9. Secure the Diagonal Braces
Hold the diagonal brace back in place, with one end against the wall and the other end flush to the top of
the rafter’s inside surface. Drive three 2 1/2-inch structural screws through the brace, into the rafter.
On the other end of the brace, drill a pilot hole through the bottom edge of brace into the wall stud. The
pilot hole should be 6 inches deep, and you should drill at a roughly 45-degree angle to accommodate
the brace’s miter angle. Use an impact driver to screw a 6-inch lag bolt through the brace into the wall.
Repeat these steps on the other side.
10.Cut and Secure the Covering Material
Cut the covering material to the dimensions of your awning, and secure it to the top. The exact process
will vary depending on the material you use.
11.Finishing Touches
Use a caulking gun to run a bead of caulk in the gap where the top of the ledger board meets the wall.
For extra aesthetic appeal, you can also fill in the exposed screw heads in the fascia board with exterior-
grade wood filler and prime, paint, or stain the awning.

How To Build A DIY Awning

Uploaded by

Copyright:

Available Formats

How To Build A DIY Awning

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

How To Build A DIY Awning

Uploaded by

Copyright:

Available Formats

How to Build a DIY Awning

poplasen / Getty Images

 Working Time: 4 - 8 hrs

 Skill Level: Intermediate

What You'll Need

 Exterior-grade 2x4 lumber (cedar, pine, or redwood)

2. Measure the Awning's Width

3. Cut the Ledger and Fascia Board to Length

4. Mark the Rafter Layout

5. Cut the Rafters to Length

Cut the rafters to length with a miter saw.

6. Make the Diagonal Braces

7. Assemble the Frame

8. Hang the Awning Frame

9. Secure the Diagonal Braces

10.Cut and Secure the Covering Material

You might also like