Description J

Digital controller RK 4004 en

Software: RK 4004-0003 F_ZG

1. Function 2
2. Type overview 7
3. Assembly 7
4. Installation 8
4.1 Terminal assignments X 1 to X 21 9
4.2 Setup operation 10
5. Parameters 13
5.1 Parameter list 13
5.2 Explanation of parameters 20
5.3 "Three position controller" upgrade 57
6. Setting values 59
7. Technical data 61

BEA--250482-EN-03

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

Explanation of symbols ➜ = jobs to be performed

= important information and instructions

1. Function
1.1 Purpose Controller card RK 4004 is used to control a DC actuator with speed
and position feedback. For this purpose a current controller, speed
controller, position controller and motor output stage are integrated
on the card. Appropriate sensors may be attached via a CAN bus for
the position controlling of running webs and following-up of tools.
Operation is via a command device with text display and/or a digital
input-output card.

1.2 Design The controller card consists of the following modules:

- a processor with data memory
- several JST plug sockets
- several terminals
- a green LED for "output stage on stand-by"
- a red LED for the "overcurrent" display
- three segment displays
- and three keys (setup, increase value, decrease value)

Green LED Red LED JST plug sockets

Segment displays

Keys:
Data memory
"Setup"

"Decrease value"

"Increase value"

JST plug sockets

JST plug sockets

Terminals

U Page 2

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

1.3 Operating principle The operating principle depends on the mode selected. The following
operating modes are possible:

Actuator manual:
In manual mode the actuator may moved to the left or right to a re-
quired position. The speed may be set in the appropriate parameter.

Actuator center position:

The actuator is positioned at the set center whereby first of all it is
moved to the reference switch and the internal position controller is
adjusted. The actuator is then moved to the set center position. The
reference switch should be mounted so that when the actuator is in
its center position the switching point of the reference is crossed thus
assuring that the actuator may be center-positioned without any ma-
jor positioning movement.

Automatic mode:
In automatic mode the web or tool is guided to the set position. Pre-
requisite to guiding is that guider lock is released.
Guider lock in automatic mode:
Guider inhibiting is only effective in automatic mode and may be acti-
vated on controller card RK 4... or via an interface.

Web offset:
A web offset may be set in automatic mode. A web offset means that
the set position value may be changed positively or negatively.
In the case of fixed sensors or a single motor support beam with two
positioning carriages, web offsetting is limited to 75 % of the sensor
measuring range. On the remaining applications with support beams
the web offset may be extended to include the entire support beam
position range.

Oscillation:
In automatic mode a oscillating set value is additionally added to the
set position value. The oscillating mode, period and path may be set
in the appropriate parameters or via a command station. In the case
of fixed sensors oscillation is only possbile within 75 % of the
measuring range.

Park sensor:
When using a support beam the positioning carriage along with the
sensor/tool located on it are moved (outwards) to the outer end posi-
tion.

Search for edge:

The sensor searches for and follows the web edge until the operating
mode is changed by, e.g. a guider enable.

U Page 3

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

1.4 Control structure with In a control structure for proportional actuators the web or tool actual
constant controlling for position value is compared with the required set position value and, in
proportional actuators the event of a deviation, it is transmitted to a P position controller as a
control difference. The resultant set speed value is compared with the
actual speed value and transmitted to the PI speed controller. The lat-
ter emits a pulse width-modulated signal at the output stage.
The following are available as proportional actuators:
DRS pivoting frame, VWS turning rod, SRS steering roller, WSS win-
ding station, SVS push roller SVS and VSS positioning and follow-up
controller.

Control structure legend

1 Operating mode 14 Actual speed value recording
2 Actuator position controller 15 Counter
3 Max. variable actuating speed in manual 16 Incremental encoder
4 Speed controller 17 Web position controller
5 Variable current controller 18 Max. variable actuating speed in automatic
6 Power output stage 19 Memory command at stop
7 Gearing with spindle 20 Right edge sensor
8 Right end position 21 Left edge sensor
9 Center position 22 Sensor selection (right web edge, left web edge, web center)
10 Left end position 23 Web offset
11 Right offset 24 Oscillation generator
12 Left offset 25 Current controller
13 Actual position memory

U Page 4

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

1.5 Control structure with In a control structure for a support beam a set speed value is deter-
constant controlling for mined on the basis of the sensor signal via the P position controller
support beams that is transmitted to the speed controller. The resulting set speed va-
lue is compared to the actual speed value and transmitted to the PI
speed controller. The latter emits a pulse width-modulated signal at
the output stage. In "search for edge" or "hybrid" modes the sensor is
driven to follow-up the web edge.
Available as proportional actuator:
Support beam VSS

Control structure legend

1 Operating mode 10 Park position
2 Sensor 11 Support beam position controller
3 Counter 12 Actual speed value recording
4 Web offset 13 Incremental encoder
5 Edge sensor position controller 14 Max. variable actuating speed in search for edge mode
6 Support beam speed controller 15 Variable current controller
7 Power output stage 16 Current controller
8 Sensor zero point detector 17 Variable actuating speed during positioning
9 Memory for edge position 18 Oscillation generator

U Page 5

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

1.6 Control structure with con- In the case of a control structure for integral actuators the web actual
stant controlling for inte- position value is compared to the required web set position value
gral actuators and, in the event of a deviation, it is transmitted as a control diffe-
rence to a P position controller. The latter provides the necessary set
position value for the actuator. The current actual actuator position
value is compared to the required set position value and transmitted
as a control difference to the actuator position controller. The latter
generates the set speed value which is compared to the actual speed
value, the difference being fed to the PI speed controller which emits
a pulse width-modulated signal at the output stage.
Available integral actuators:
SWS segmented roller guider, VGA pivoting roller, BCS edge and
width spreader

Control structure legend

1 Operating mode 14 Actual speed value recording
2 Actuator position controller 15 Counter
3 Max. variable actuating speed in manual 16 Incremental encoder
4 Speed controller 17 Web position controller
5 Variable current controller 18 Max. variable actuator speed in automatic
6 Power output stage 19 Memory command at stop
7 Gearing with spindle 20 Right edge sensor
8 Right end position 21 Left edge sensor
9 Center position 22 Sensor selection (right web edge, left web edge, web center)
10 Left end position 23 Web offset
11 Right offset 24 Oscillation generator
12 Left offset 25 Current controller
13 Actual position memory

U Page 6

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

The following table provides an overview of the most common digital

2. Type overview controllers. The individual digital controllers (DC) are listed in the ver-
tical column. The crosses mark the components belonging to them
(AK ...., LK ...., etc.).

Type RK 4004 AK 4002 LK 4203 RT 4019 DO 2000 AK 4014

DC 0310 X X
DC 0311 X X X
DC 0340 X
DC 0341 X X
DC 0360 X X
DC 0361 X X X
DC 1310 X X X
DC 1340 X X
DC 2340 X X
DC 2341 X X X

Controller card RK 40.. is usually mounted in a sheet steel housing or

3. Assembly E+L device.
If the controller card is supplied on its own it should be mounted in a
control cabinet away from heavy current-carrying modules.
The maximum distance to the DC actuator must not exceed
10 m.

U Page 7

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

➜ Connect electrical leads according to the attached wiring diagram.

4. Installation
➜ Shield and run signal lines away from heavy current-carrying
leads.
The DC actuator motor line must be run separately (separate ca-
ble) from the incremental encoder line.
The connection line between the controller card and DC actuator
may be run in one lead up to a length of 3 m. From a distance of
3 m to 10 m the motor and incremental encoder lines must be
run separately.

X5 Right X6 Left
X 12 CAN connection
digital digital
without LED display
X 15 Fan sensor sensor
for internal device
networking
X7 CAN connection
with LED display
for CAN device
X 21 Supply voltage connector
for further E+L
X 11 SPI bus
modules
X9 serial bus

X 13 Supply voltage
for further E+L
modules X8 Analogue card
AK 4002
(only when ana-
logue sensors are
X1 Operating volta-
used)
ge
X 14 External configu-
ration adapter

X 10 Optical incre-
mental encoder

X2 DC actuator X3 Command sta- X4 Reference X 20 End switch

and incre- tion for web switch, guider
mental en- offset RE .... or lock and end
coder signal for path- position signal
dependent
oscillation

RK 40.. terminal assignments

The wiring diagram indicates which connectors are assigned.
The guider lock is intended for on-site requirements where the actua-
tor is to be stopped in its current position. If the guider lock is closed
(make contact) the actuator remains in this position until the contact
is open again.

U Page 8

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

4.1 Terminal assign-

ments X 1 to X 21
Terminal No. Input Output Assignment
X1 1 X +24 V DC supply voltage
2 X 0V
3 X Ground
X2 1 X DC actuator
2 X DC actuator
3 X Incremental encoder on DC actuator track A
4 X Incremental encoder on DC actuator track B
5 X +24 V DC
6 X 0V
X3 1 X +24 V DC
2 X Web offset or path-dependent or
Oscillation signal or
automatic mode signal (for minimum operation only)
3 X 0V
4 X Sensor range limit
X4 1 X Guider lock
2 X 0 V potential 0 V for controller lock
3 X +24 V DC reference switch
4 X Reference switch signal
5 X 0 V reference switch
6 X +24 V DC
7 X Actuator end position signal
8 X 0V
X7 1 X X CAN High
2 X X CAN Low
3 X LED +
4 X LED -
X 10 1 X GND (0 V)
2 X (Index) -
3 X Track A
4 X +5 V
5 X Track B
X 12 1 X X CAN High
2 X X CAN Low
3 - - free
4 - - free
X 13 1 X +24 V
2 X GND 0 V
X 15 1 X +12 V
2 X Switch output
X 20 1 X +24 V
2 X Actuator 2nd end position signal
3 X 0V
4 X system on stand-by
X 21 1 X +24 V
2 X 0V

U Page 9

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

4.2 Setup operation The three keys and the displays are used as the setup control panel.
The key assignment (setup, decrease/increase value) is indicated in
the illustration opposite. The following applications are possible:
4.2.1 Setting the controller card device address
4.2.2 Current error display
4.2.3 Setting parameters

4.2.1 Set controller card Prior to commissioning the device address of controller card
device address RK 4004 must be checked and changed as necessary.
➜ Press both keys "decrease value" and "increase value" at the
same time. The group number is indicated via the "decrease value
" key and the device number via the "increase value" key. If both
keys are held down for longer than approx. 4 seconds the device
address will start to flash.
➜ If the device address deviates from the required address it may be
changed via the keys.
If none of the keys are actuated the device address will be saved
after approx. 20 seconds have elapsed and a software reset is
triggered.

U Page 10

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

4.2.2 Current error display In normal circumstances the display on the controller card indicates
only three dots. These three dots signal that no errors are present .
A flashing number signals an error. The number indicates the error
code. If several errors are present at the same time, the error with the
highest priority will be indicated. If this error is no longer present, the
display will indicate the next error.
Below is a list of possible errors:

No. Error display in Description Output at

CANMON terminal X 20.4
1 UDC-power low 19.5 VDC operating voltage not attained 0
2 UDC-power high 30.5 VDC operating voltage exceeded 0
3 I motor high set maximum cut-off current exceeded -
o
4 temp case high heat sink over 70 C 0
5 encoder fault incremental encoder motor fault -
6 encoder invers incremental encoder motor inverted -
7 sensor R fault no message from right sensor -
8 sensor L fault no message from left sensor -
9 gearconstant fault calculated gear constant produces impermissible value -
10 motor line fault motor line interrupted 0
12 power stage defect motor power stage defective 0
13 motor blocked motor blocked due to overloading (I = max. & n = 0)
Attention! output is set after 5 seconds only 0
14 ref. switch error several reference switch errors detected. -
15 end switch error end position proximity switches incorrectly configured -
16 24Vext. fault ext. supply voltage overloaded. 0

4.2.3 Output X 20.4 In the case of certain errors (see table) output X 20.4 is switched to
"0". The internal switch on the controller card that furnishes a con-
nection to ground is opened.
The following circuit variants are recommended:

Lamp "ON" = system on stand-by PLC "1" = system on stand-by

Lamp "OFF" = error PLC "0" = error

U Page 11

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

4.2.3 Parameter setting All parameters in the CAN network may be selected and changed by
the three keys. The following flow diagram illustrates basic operation
with the setup editor:

Basic operation in setup mode:

Para- Para-
meter meter-
Start setup mode: press the setup and additio- value
nally the increase value key (press the setup key +
first). The green LED on the setup key will flash . Start setup mode

Enter device number: press and hold down the

setup key and select parameter 0 via the increase
value key. Release the setup key again and enter
the device number via the increase or decrease +
value keys (device number is specificed in the Enter device number
block diagram) or
Enter group number: press and hold down the
setup key and select parameter 1 via the increase
value key. Release the setup key again and enter
the group number via the increase or decrease +
Enter group number
value keys (group number is specified in the
or
block diagram)

Select and change parameters: press and hold

down the setup key and select the required para-
meter via the increase value key. Release the set- +
up key again and enter the required parameter Select parameter
value via the increase or decrease keys.
Change parameter value
Incorrect parameter changes may impair or
the function of the entire system !

May parame- yes

ter value be
changed

no

Select expanded setup mode: select device +

number X.5, then press and hold down the setup
Expanded setup mode
key and select parameter 3 by pressing the
increase value key. Release the setup key again
and enter parameter value 42 via the increase or or
decrease value keys.

Select
further ja
parameters

no
Quit setup mode: select device number X.5, then
press and hold down the setup key and select +
parameter 3 by pressing the increase value key.
Release the setup key again and enter parameter
1 by pressing the increase or decrease value key. Quit setup mode
or
Press and hold down the setup key
and press the increase value key once. Release +
the setup key again.

X is used as a place retainer

U Page 12

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

In setup mode parameters may be displayed and to some extent

5. Parameters changed as well. In order to access the controller card setup
mode a command station DO .... , a operating panel RT .... or an
E+L CANMON program is required.

5.1 Parameter list The parameter numbers are listed in the Number field of the table, in
the Name field the abbreviation. The Default field indicates the stan-
dard settings, Min and Max are the permissible limit values respec-
tively. The unit is indicated in the Unit field. The Description explains
the parameter function. If a dot (•) comes after the parameter number
this indicates that it is a display parameter, the value of which cannot
be changed.

No. Name Default Min. Max. Unit Description

..0. edit device 5 1 F hex select device number

see block diagram for device number

..1. edit group 0 0 7 hex select group number

see block diagram for group number

..2. reset settings 0 0 2 Works settings

0 = no function
1 = perform customer settings
2 = perform internal default setting

..3. start service 0 0 199 Starting a function

0 = no function
1 = reset controller
2 = save parameter
10 = actuator initialisation run (device X.5)
11 = support beam initialisation run
(device x.6, x.7, x.8, x.9, x.10, x.11)
12 = actuator initialisation run, with specification
of the gear constants (device x.5)
13 = actuator guiding criterion photo
(for integral controller only)
22 = saving of application parameters
30 = preset for general web guider parameters
31 = preset for sensor support beam VS 35 parameters
32 = preset for 3-position controller parameters
33 = preset for DR 11.. / DR 12.. parameters
34 = preset for support beam VS 50.. parameters
42 = select expanded setup
44 = save customer settings
98 = delete error memory
99 = delete data memory

..4. • RK 4004 1.6 1.2 1.6 E+L Software version

..5. • webedge offset Parameter title

..6. weboffset 0.00 -325.00 325.00 mm Web offset

..7. step width 0.10 0.01 10.00 mm Step width for web offset

..8. osc. amplitude 0.0 0.0 500.0 mm Oscillation amplitude +/-

..9. osc. cycl. time 20 1 700 sec. Oscillation cycle time

cycle-dependent = sec/ cycle
path-dependent = pulse/ cycle

U Page 13

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

No. Name Default Min. Max. Unit Description

.1.0. osc. wave form 95 5 95 % Oscillation progression

5% = square wave
50% = trapezoidal wave
95% = delta wave

.1.1. >osc. trigger mode 2 0 7 Oscillation operation

0 (4) = operation via keyboard
1 (5) = operation via AUTO key
2 (6) = oscilation OFF
3 (7) = oscillation ON

Values in () for path-dependent oscillation

.1.2. • webedge controller Parameter title

.1.3. prop range +/- 10.0 -2000.0 2000.0 mm Guider proportional range
Web offset in mm at which the DC actuator
runs at maximum speed.
Decrease value in case of inaccurate guiding!
Increase value in case of uneven guiding!

.1.4. dual-rate width 30 10 90 % Window width in % in relation to the sensor scan range
This value is used to establish the switch point for
determing the dual rate characteristic curve.

.1.5. dual-rate level 100 0 150 % Positioning velocity reduction

This value is used to determine % motion speed at
the switch-over point.

.1.6. velocity auto 20 0 1000 mm/s Max. positioning velocity speed in automatic mode

.1.7. velocity pos 50 0 1000 mm/s Positioning velocity speed in positioning mode

.1.8. velocity jog 10 1 1000 mm/s Positioning velocity speed in jog mode

.1.9. velocity defect 1 1 1000 mm/s Positioning velocity when exceeding the set threshold

.2.0. • derated velocity 1000 mm/s Display of velocity limited by internal functions
(only active for selecting in parameter 1.1.8.)

.2.1. reserved 21 not assigned at present

.2.2. defect range ± 10.0 0.0 2000.0 mm range for detecting a web fault
if not attained switching to the set "velocity defect" speed
will be performed

.2.3. • servo configuration Parameter title

.2.4. motion direction 0 0 1 Motion effective direction

0 = normal
1 = inverted
Depends on mounting position and web direction of travel

.2.5. motion range total 0.0 0.0 3270.0 mm Total motor position range on calibration
AG positioning path must be entered prior to calibration

.2.6. positionrange + 0.0 0.0 3270.0 mm Positive motor position range

.2.7. positionrange - 0.0 -3270.0 0 mm Negative motor position range

.2.8. alarm limit % 75 0 100 % Limit value for end position early warning

U Page 14

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

No. Name Default Min. Max. Unit Description

.2.9. reserved 29 not assigned at present

.3.0. reference offset 0.0 -3270.0 3270.0 mm Reference switch offset

Distance between reference switching point and
AG- positioning range center

.3.1. center offset 0.0 -3270.0 3270.0 mm Centring offset

Distance between actuator positioning range center and
required actuator 0-position in „center position“ mode.

.3.2. system offset 0.0 -3270.0 3270.0 mm System offset

Distance between set actuator 0-position and the
reference point (e.g. machine center).

.3.3. • total resolution 0.0 0.0 3270.0 p/mm Motor gear constant
display only.

.3.4. encoder resolution 8 8 9999 p/revrev encoder resolution

entry of rev encoder resolution pulse/rev
(without 4-fold evaluation)

.3.5. rotation gear 8.0 0.1 100.0 Gear transmission on motor

Entry of gear transmission

.3.6. linear gear 4.0 0.1 250.0 mm/rev Linear gear transmission
Entry of transmission ratio from
rotational to linear movement

.3.7. mech. gearfactor 1.00 0.10 5.00 - Mechanical ratio

.3.8. reserved 38 not assigned at present

.3.9. reserved 39 not assigned at present

.4.0. • pos. controller Parameter title

.4.1. pos prop +/- 5.0 0.1 200.0 mm Position controller proportional range

.4.2. • act position 0.0 -3270.0 3270.0 mm Actual position (display only)

.4.3. • set position 0.0 -3270.0 3270.0 mm Set position (display only)

.4.4. pos source adress 00 00 7F - Master address

Address from which the master set position is received

.4.5. prop stroke +/- 100 0 2000.0 mm Actuator correction path in the event of
a web fault of (.1.3. prop range +/-)

.4.6. • photo auto offset 0 -2000.0 2000.0 mm Actuator offset between set center and set operating
point during automatic mode
is set for <SETUP>+<AUTO>.
Only if function is activated via „Configuration SYS“.

.4.7. • speed controller Parameter title

.4.8. max. motor speed 1250 100 4000 rpm Motor speed characteristic value
Value is required for speed limiting

.4.9. • act. speed rpm Current motor speed (display only)

.5.0. speed_P 2.00 0.01 10.00 P component for speed controller

.5.1. speed_I 0.10 0.01 5.00 I component for speed controller

U Page 15

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

No. Name Default Min. Max. Unit Description

.5.2. accel. time 0.0 0.1 10.0 sec. Acceleration time

.5.3. • I-PWM Current I-PWM-value (display only)

.5.4. reserved 54 not assigned at present

.5.5. • current controller Parameter title

.5.6. cut-off current 8.0 0.0 10.0 A Cut-off current of motor output stage

.5.7. motorcurrent 1.0 0.0 7.0 A Max. permissible nominal motor current

.5.8. dyn. currentfactor 150 100 200 % Dynamic motor current rise
Motor is overloaded briefly by the variable factor

.5.9. therm. timeconst. 60 1 200 sec. Thermal time constant for brief motor current excess

.6.0. • limited current - -7.00 7.00 A Current permissible motor current

.6.1. • act. current - -20.00 20.00 A Actual measured motor current

.6.2. current_P 2.6 0.0 100.0 P component for current controller

.6.3. current_I 0.4 0.0 50.0 I component for current controller

.6.4. • set current Set motor current display

.6.5. reserved 65 not assigned at present

.6.6. reserved 66 not assigned at present

.6.7. reserved 67 not assigned at present

.6.8. • diagnostics Parameter title

.6.9. • system error xx Error display

1 = supply voltage < 20 V DC
2 = supply voltage > 30 V DC
3 = cut-off current exceeded
4 = heat sink temperature > 70 °C
5 = incremental encoder defective
6 = incremental encoder inverted
7 = no message from right sensor
8 = no message from left sensor
10 = motor line interrupted
11 = motor blocked
12 = motor output stage defective
13 = motor blocked
14 = reference switch has several switching points
15 = end pos. proximity switches incorrectly configured
16 = external voltage output overloaded

.7.0. reserved 70 not assigned at present

.7.1. reserved 71 not assigned at present

.7.2. • running time meter x h Running time meter

.7.3. • supplyvoltage 24DC xx.x V Operating voltage

o
.7.4. • temperature case xx C Heat sink temperature

U Page 16

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

No. Name Default Min. Max. Unit Description

o
.7.5. • temp. case max. xx C Maximal heat sink temperature reached

.7.6. reserved 76 not assigned at present

.7.7. reserved 77 not assigned at present

.7.8. • mainloops/sec. - 0 32000 Hz For internal evaluation only

.7.9. • I/O configuration Parameter title

.8.0. • >digi input status - 00 FF HEX Display of current digital inputs

.8.1. reserved 81 not assigned at present

.8.2. >usage input X4.1 2 -10 10 Use of input X4.1

.8.3. >usage input X4.4 3 -10 10 Use of input X4.4

.8.4. >usage input X4.7 4 -10 10 Use of input X4.7

.8.5. >usage input X20.2 - -10 10 Use of input X20.2

.8.6. >usage input X.3.2 - -10 10 Use of input X3.2

.8.7. reserved 87 not assigned at present

.8.8. reserved 88 not assigned at present

.8.9. reserved 89 not assigned at present

.9.0. reserved 90 not assigned at present

.9.1. • system config. Parameter title

.9.2. >controller type 0 0 3 Controller type

0 = Proportional actuators
1 = Integral actuators
2 = Slave drive
3 = 3 position controller

.9.3. control mode 0 0 99 Control mode

.9.4. >auto address 1 0 2 Automatic sensor address assignment

0 = display only of sensor addresses
1 = automatic setting of the sensor addresses to
x.1/x.2
2 = setting of the sensor addresses to those set in
parameters .95. and .96.

.9.5. CAN connector 0.0 0.0 7.F Address of the sensor at the right slot
Right

.9.6. CAN connector Left 0.0 0.0 7.F Address of the sensor at the left slot

U Page 17

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

No. Name Default Min. Max. Unit Description

.9.7. >function config 1 0801 0000 FFFF System configuration1

[X] Frame limit check 0x0001
[ ] N~ / M control 0x0002
[ ] Center direct 0x0004
[ ] Ref on power on 0x0008
[ ] Watch webedge R 0x0010
[ ] Watch webedge L 0x0020
[ ] Photo on autokey 0x0040
[ ] Sens. err. > Center 0x0080
[ ] MCP active 0x0100
[ ] Auto. SensorFree 0x0200
[ ] Support 2 motor 0x0400
[X] Weboffset 1/10 mm 0x0800
[ ] Weboffset inverted 0x1000
[ ] Defect detection 0x2000
[ ] ext. system mode 0x4000
[ ] RE 1721 0x8000

.9.8. >function config 2 0000 0000 FFFF System configuration 2

(*) No Controller output 0x0000
( ) N-target -> CAN 0x0001
( ) Delta N -> CAN 0x0002
( ) Pos-target -> CAN 0x0003
( ) Delta Pos -> CAN 0x0004
( ) I-target -> CAN 0x0005
[ ] Disable I loop 0x0008
[ ] Send targetpos. 0x0010
[ ] Lock webspeed 0x0020
[ ] Start AUTO slow 0x0040

.9.9. >operatorkey config 0000 0000 FFFF Operator key

[ ] use all sensors 0x0001
[ ] Auto -> take photo 0x0002
[ ] force support free 0x0004
[ ] Cente -> supp. free 0x0008
[ ] unused sup. free 0x0010
[ ] no edge -> sens free 0x0020
[ ] sens sel. direct 0x0040
[ ] emergency sensor L 0x0080
[ ] emergency sensor R 0x0100
(*) lost web: ---- 0x0000
( ) lost web: Center 0x1000
( ) lost web: Manual 0x2000

1.0.0. reserved 100 not assigned at present

1.0.1. delaytime 1 1.0 0.0 10.0 s Delay time 1 (for switching to emergency sensor)

1.0.2. delaytime 2 1.0 0.0 10.0 s Delay time 2 (for switching to main sensor)

1.0.3. subsystem 0 adress 00 00 7F hex Serial bus card 0 address

1.0.4. subsystem 1 adress 00 00 7F hex Serial bus card 1address

1.0.5. subsystem 2 adress 00 00 7F hex Serial bus card 2 address

1.0.6. subsystem 3 adress 00 00 7F hex Serial bus card 3 address

1.0.7. • calibration Parameter title

1.0.8. calib. UDC 1.00 0.80 1.20 Operating voltage calibration

1.0.9. offset. I-act 0 -50 50 Motor current measurement offset

1.1.0. calib. I-act 1.00 0.80 1.20 Motor current measurement calibration

U Page 18

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

No. Name Default Min. Max. Unit Description

1.1.1. reserved 111 not assigned at present

1.1.2. • webspeed config. Parameter title

1.1.3. webspeed constant 10 10 100 I/m Normalisation of web speed recording

Value corresponds to the input pulse figure per
running meter of the web

1.1.4. webspeed max. 0 0 4000 m/min Maximum web speed

1.1.5. webspeed limit 0 0 4000 m/min Web speed limit

1.1.6. • actual webspeed 0 0 4000 m/min Current measured web speed

1.1.7. • adaptive controle Parameter title

1.1.8. adaptive function 0 0 3 Selection of the adaptive amplification functions

0 = no intervention in the proportional range
1 = proportional range depends on an
external CAN signal
2 = proportional range depends on the
web speed
0 = no intervention in the positioning velocity
4 = positioning velocity depends on an
external CAN signal
8 = positioning velocity depends on the web
speed
0 = no intervention in the positioning path
16 = the positioning path depends on an external
CAN signal
32 = the positioning path depends on the web speed

1.1.9. • adaptive ratio 0 0 409,6 % Display of the current control loop amplification

1.2.0. max webspeed ratio 0 0 409,6 % Adaptive factor in % at maximum web speed

1.2.1. lim webspeed ratio 0 0 409,6 % Adaptive factor in % at web speed limit

1.2.2. reserved 122 not assigned at present

1.2.3. reserved 123 not assigned at present

1.2.4. reserved 124 not assigned at present

1.2.5. • !! Service !! Parameter title

1.2.6. service off / on 0 0 1 Switching on service mode

1.2.7. >service mode 0 0 9 Service mode

! for service personnel only !
(*) Square current controller test 2
( ) Delta current controller test 3
( ) Speed controller test 4
( ) Speed controller test 5
( ) PWM square bridge signal 6
( ) PWM delta bridge signal 7
( ) Square position set value 8
( ) Delta position set value 9

1.2.8. testvalue 1 0 -100 100 % Test value 1 for service mode ! for service personnel only!

1.2.9. testvalue 2 0 -100 100 % Test value 2 for service mode ! for service personnel only!

1.3.0. testcycletime 0.01 0.01 10.00 s Test cycle time for service mode ! for ser. personnel only !

U Page 19

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

If the following sign ">" is set in front of the parameter it may be

edited with the help of a parameter value list (selection list) in
CANMON or DO 200. .
Editing with Canmon:
Select the "Value" field and open the parameter list via the enter key.
Select the required parameter value with the cursor keys, to mark the
parameter value press the space bar .
Parameter value list (selection list)
Editing with command station DO 200.:
Select the required parameter value via the "increase value"/"decrea-
se value" keys, to mark the parameter value press the acknowledge
key.

5.2 Explanation of parameters ..0. edit device

..1. edit group
The device address consists of the device and group numbers. Each
device with a CAN connection (serial or parallel) possesses its own
device address that may only be assigned once in the entire CAN
network .
In order for a specific device to be addressed in the control loop the
device number must be set in parameter "..0. edit device" and the
group number in parameter "..1. edit group". The device and group
numbers are specified in the block diagram for each device with a
CAN address.

..2. reset settings

In the event of incorrect functioning or parameter entries, the E+L ba-
sic settings or default values may be reloaded. The following settings
are possible:
1 = perform customer settings. This customer setting is only possible
on compact systems set by E+L prior to delivery where all para-
meter settings were saved in a backup list. The setting values
are thus reloaded.
2 = perform basic settings. The default values specified in the para-
meter list are loaded. The default values are however only loaded
for the currently selected device. No parameter values are chan-
ged on the remaining devices.

..3. start service

Use this parameter to start various processes that are particularly re-
quired on commissioning the system. The following functions are pos-
sible:

U Page 20

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

1 = Reset guider
In this reset all parameter values for the selected device are sa-
ved and a restart performed. Every time parameter values are
changed setup mode should always be quit via 1 to assure that
all changed parameter values are saved.
2 = Save parameters
Function 2 is identical to function 1, the only difference is that
no restart is performed for the selected device.
10 = Actuator initialisation run (with specification of the motion
path)
Prior to the initialisation run the actual positioning path must be
established and entered in parameter ".2.5. total motion range".
The actuator initialisation run is started by entering the value
10. Prior to starting the actuator should be located in its center
position for this start position is saved as the new center positi-
on. The latter may also be corrected manually at any time via
parameter ".3.1. center offset".
11 = Initialisation run-support beam
By entering value 11 the initialisation run for all support beams
featured in this group is performed.
12 = Initialisation run-actuator (with specification of motor and
gear data)
In this initialisation run by first entering the motor and gear data
(parameter .3.4./.3.5./.3.6. and .3.7.) the maximum positioning
path is established and entered in parameter ".2.5. total motion
range".
13 = Capture of guiding criterion photo
On follow-up control systems the position of the actuator/tool is
controlled according to the detected web position. In order to
calibrate the offset, a guiding criterion photo of the actuator
must be taken. To this end, the actuator is moved to the requi-
red location manually. While the actuator guiding criterion photo
is being taken, the offset is calculated on the basis of the cur-
rent actuator position and the web position and entered in para-
meter ".4.6. photo auto offset".
22= Save system parameters
The parameter values of certain parameters are additionally
stored and not deleted in the case of possible data memory de-
letion. The following parameters are saved: .8.2. / .8.3. / .8.4. /
.8.5. / .8.6. / .9.2. / .9.7. / .9.8. und .9.9. .
30 = general web guider basic parameter setting
31 = VS 35 .. support beam basic parameter setting
32 = 3 position controller basic parameter setting
33 = VS 50.. support beam basic parameter setting
The device-specific parameters are preset for the specified de-
vices by entering the appropriate value.

U Page 21

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

42 = Expanded setup-mode
In setup mode all existing parameters may be selected and the
parameter values viewed. Some of the parameter values may
be changed immediately. The protected parameters may only
be changed once value 42 has been entered. This entry furnis-
hes access to what is known as "expanded setup-mode". In ex-
panded setup mode all parameters that can be changed, may
be changed.
44 = Save customer settings
In this form of saving all parameter settings are stored in a
backup list. If necessary, all customer-specific settings may be
reloaded using parameter "..2. reset settings" .
98 = Delete error memory
This command should only be used by E+L service personnel.
The controller card can store up to 100 errors that have occur-
red. If the number of errors exceeds the 100 mark, the error
messages are pushed out at the back of the error memory and
are thus deleted.
99 = Delete data memory
This command should be used by E+L service personnel. The
entire data memory of the controller card is deleted. Once the
controller card is switched on the default values are automati-
cally loaded.
No commands are performed until a parameter change has
been executed!

U Page 22

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

Parameter value Software version ..4. RK 4004

1.0 A The current software version of the controller card is displayed. The
1.1 B number after the dot indicates the software version.
1.2 C
1.3 D
1.4 E
1.5 F
etc.

..5. webedge offset

Parameter block for setting the web offset.

..6. web offset

The web offset permits the displacement of the set web position to
Sensor zero point
the left or right during automatic mode. The offset is set directly in
this parameter by a command station or via a digital interface. The
step width for web offsetting may be set in parameter ". .7. step
width". The offsetting of the set position is displayed on the command
station in mm. A set web offset is preserved, even when the opera-
ting voltage is switched off, until a new entry is saved, .
Web offset to the right in the In the case of fixed sensors or a single motor support beam with
direction of web travel two positioning carriages the web offset is limited to 75 % of the
sensor measuring range. For the remaining applications with sup-
port beams and cameras the web offset may be increased to the
maximum parameter value .

..7. step width

The step width of the web offset per key push may be be set in
1
/100 mm. The web offset is changed by this set value by pressing a
key on the command station.

..8. osc. amplitude

During the oscillation stroke it is determined by how far to the left and
right the actuator will swing in oscillation mode. The oscillation stroke
may be entered directly in this parameter or via a command station
with oscillation feature. Entering is performed in 1/10 mm.
In the case of fixed sensors or a single motor support beam with
two positioning carriages the oscillation stroke is limited to 75 % of
Oscillation the sensor measuring range.
stroke

U Page 23

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

..9. osc. cycl. time

Cycle-dependent:
The cycle time (oscillation time tc) for an oscillation period is esta-
blished here. The longer the period, the slower the actuator oscillates.
Entry may be directly in the parameter or via a command station with
oscillation function.

Oscillation time tc

Path-dependent:
In path-dependent oscillation the oscillation period is determined by
path-dependent, external pulses. The oscillation period is divided up
into n-sections. The maximum number of pulses must not exceed 20
pulses per second.
The number of pulses to be set may be calculated as follows:
1. Establish path length per oscillation period

n-sections

web length s

s s = web length per oscillation period

2. Establish maximum oscillation frequency

fc max = maximum oscillation frequency (1/s)

Vmax
fc max = Vmax = maximum web speed (m/min)
s x 60
s = web length per oscillation period (m)

3. Establish no. of pulses

The maximum number of pulses per period is limited by the maxi-
mum input frequency of fe max 20 Hz.

fe max = maximum input frequency 20 Hz

fe max
n= fc max = oscillation frequency (Hz)
fc max
n = no. of pulses per period

The no. of pulses n is entered in the parameter.

Dimensioning of the external pulse generator may be determined as

follows:
fa max = maximum pulse generator output frequency (Hz)
n
fa max = s = web length per oscillation period (m)
s
n = no. of pulses per period
The external pulse generator must emit the calculated no. of pulses
fa max at maximum web speed.

U Page 24

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

.1.0. osc. wave form

s Oscillation mode determines the oscillation course. By entering a va-
lue of between 5 and 95 oscillation progression may be changed
from square to delta wave.
"5" t 5 = Square-wave (steep rise/drop of the oscillation signal, long
dwelling period in the oscillation end position
s
95 = Delta-wave (shallow rise/drop of the oscillation signal, short
dwelling period in the oscillation end position
"95"

.1.1. >osc. trigger mode

Depending on the command station featured, oscillation may be star-
ted in different manners. In addition, the differentiation must be made
of whether cycle or path-dependent oscillation is concerned.
In the case of cycle-dependent oscillation the duration of an oscillati-
on cycle depends on the set time and in the case of path-dependent
oscillation on the external pulses (see parameter "..9. osc. cycl.
time").
On switching-off oscillation the cycle in progress is continued to
the next zero pass. In the case of path-dependent oscillation the
corresponding pulses must be supplied up to the zero pass. For
path-dependent oscillation the digital input X 3.2 must be pro-
grammed to "web speed measuring" (see parameter .8.6.).
The following table illustrated the various setting options:

Parameter value: Explanation:

Cycle Path-
dependent dependent
0 4 Oscillation is switched on together with automatic mode or off via a command
station with oscillation key or digital interface (command code), independently
of the automatic key.
1 5 If no command station with oscillation key is featured, oscillation may in this
case be switched on or off via the automatic key. After starting automatic mode,
by pressing the automatic key oscillation is started or stopped while the actua-
tor always remains in "automatic" mode.
2 6 Oscillation is generally switched off. Even if an oscillation key is featured, oscil-
lation cannot be started.
3 7 Oscillation is always active. Automatic mode without oscillation is not possible.
Oscillation is started together with automatic mode!

.1.2. webedge guider

Parameter block for setting the web guider.

U Page 25

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

.1.3. prop range +/-

On proportional actuators the amplification of the position con-
troller is set via the two parameters ".1.3. Prop range ±" and ".1.6.
velocity auto". On integral actuators amplification is set via the
two parameters ".1.3. Prop range ±" and ".4.5. prop stroke".
With regard to the following considerations please always take into
account that a change to one of the two parameters will always in-
fluence amplification.
Amplification is correctly set if, after brief overshooting the error is
Amplification too high
corrected. If the position controller is set with too great a degree of
sensitivity, the guider will overshoot as well. In the case of too little
amplification the control loop will be too slow. Optimum amplification
Amplification right may be determined with a characteristic curve tracer. In practice, am-
Amplification too low plification may also be determined by trial and error.

Proportional actuator:
The smaller the set proportional range at a constant maximum posi-
tioning velocity (Parameter ".1.6. velocity auto") is, the greater the
amplification of the web guider will be.
A negative proportional range causes negative amplification, the
effective direction is thus inverted in automatic mode.

Velocity correction
Proportional range
.1.3. prop range ±
established correction 2,0 3,5
positioning velocity de-
pending on proportional
range 15 mm/s
8 mm/s

Control deviation

Positioning velocity
.1.6. velocity auto
20 mm/s

Set position
(sensor measuring range cen- Control deviation of
ter ) 1.5 mm

U Page 26

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

By reducing the proportional range the characteristic curve (see fig.)

will become steeper. The steeper the characteristic curve the greater
the positioning velocity will be in the case of a control deviation and
the system thus more sensitive. The positioning velocity of the actua-
tor may be determined on the basis of the characteristic curve re-
gardless of the control deviation.

In this example a proportional range of 2 mm or 3.5 mm has been

assumed at a maximum motion speed of 20 mm/s.
Given a control deviation of 1.5 mm the positioning velocity is
15 mm/s for a proportional range of 2 mm and 8.0 mm/s for a pro-
portional range of 3.5 mm.
The values may also be calculated arithmetically:
Amplification (G) = parameter .1.6. / Parameter .1.3.
Correction velocity (VK) = control deviation * amplification (G)

Example 1: Example 2:
1
G = 20/2 = 10 /s G = 20/3.5 = 5.71 1/s
VK = 1.5 mm * 10 1/s VK = 1.5 mm * 5.71 1/s
VK = 15 mm/s VK = 8.6 mm/s

Proportional actuator optimisation:

Reduce the proportional range by small steps only. Following each
change of the parameter value a web deviation should be produced
manually in automatic mode so that oscillation may be detected im-
mediately.
Reduce the proportional range until the guider starts to oscillate. The
increase the proportional range again until no more oscillation may
be observed.

U Page 27

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

Integral actuator:
The smaller the set proportional range is for the maximum correction
path of the actuator (parameter ".4.5. prop stroke ±"), the greater the
amplification of the web guider.
A negative proportional range causes negative amplification, the
effective direction in automatic mode is thus inverted.

Correction Proportional range

positioning path .1.3. prop range ±
2.0 3.5
established correction
positioning path depen-
ding on proportional 18 mm
range
10.5 mm

Control deviation

Correction positioning
path
.4.5. prop stroke ±
25 mm

Set position
(Sensor measuring range
Control deviation of
center)
1.5 mm

By reducing the proportional range the characteristic curve (see fig.)

becomes steeper. The steeper the characteristic curve the greater
the positioning path of the actuator given a control deviation and the
more sensitive the system becomes. The correction positioning path
of the actuator may be established on the basis of the characteristic
curve independently of the control deviation.
In this example a proportional range of 2 mm or 3.5 mm has been
assumed with a correction positioning path of 25 mm.
Given a control deviation of 1.5 mm the correction positioning path
amounts to approx. 18 mm with a proportional range of 2 mm and
with a proportional range of 3.5 mm approx. 10.5 mm .

U Page 28

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

The values may also be calculated arithmetically:

Amplification (G) = parameter .4.5. / parameter .1.3.
Correction positioning path (SK) = control deviation * amplication (G)

Example 1: Example 2:
G = 25/2 = 12.5 G = 25/3.5 = 7.14
SK = 1.5 mm * 12.5 SK = 1.5 mm * 7.14
VK = 18.75 mm VK = 10.71 mm
Integral actuator optimisation:
Reduce the proportional range by small steps only. Following each
change of the parameter value the a web deviation should be produ-
ced manually in automatic mode so that oscillation may be detected
immediately.
Reduce the proportional range until the guider starts to oscillate. The
increase the proportional range again until no more oscillation may
be observed.

.1.4. dual rate width

.1.5. dual rate level
These two parameters have no function with an integral guider.
If the web edge is subject to certain fluctuations (uneven edges) the-
Window width se two parameters may be used to determine a range in which, given
.1.4. dual rate width a deviation from the set position, the correction velocity of the actua-
tor is reduced in the case of proportional guiders.
Positioning velocity
reduction Given a web edge progression as illustrated opposite, the actuator
.1.5. dual rate level would normally try to correct the deviation according to the broken
line. The actuator would only oscillate and the control result would not
be satisfactory. The broken line represents the controller amplification
(parameter .1.3. / .1.6.).
Within the set window width ".1.4. dual rate width" the positioning
velocity is reduced in the case of a control deviation. The positioning
Set position velocity reduction is set in parameter ".1.5. dual rate level". Potential
oscillation due to edge errors may thus be reduced. If the edge error
exceeds the set window width range the positioning velocity is
increased (see fig. on left).
Both parameter values are % entries and are related to the set valu-
es of parameter ".1.3. prop range ±" and ".1.6. velocity auto"
Example:
The following values are set in the parameters.
Error of uneven
edge .1.3. prop range ± : 10.0 mm
.1.6. velocity auto : 20 mm/s

U Page 29

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

.1.4. dual-rate width : 50 %

.1.5. dual-rate level : 70 %
Window width = 10.0 mm * 50 % / 100 = 5 mm
Reduced pos. velocity = 20 mm/s * 70 % / 100 = 14 mm/s
Within ±5 mm of the set web position a web error is corrected at a
maximum motion speed of 14 mm/s.

.1.6. velocity auto

The greater the set maximum positioning velocity is given a constant
proportional range (parameter ".1.3. prop range ±"), the greater the
amplification of the web guider will be in automatic mode.

Correction Proportional range

velocity .1.3. prop range ±
established correction 2.0
velocity depending on
the positioning velocity
15 mm/s
11 mm/s

Control deviation Positioning velocity

.1.6. velocity auto
15 mm/s
20 mm/s

Set position
(Sensor measuring range Control deviation of
center ) 1.5 mm

By increasing the maximum positioning velocity the characteristic

curve becomes steeper (see fig.). The steeper the characteristic cur-
ve the greater the positioning velocity will be given a control deviation
and the more sensitive the system will become. The positioning
velocity with which the actuator tries to correct the error may be de-
duced from the characteristic curve.

U Page 30

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

In this example a maximum positioning velocity of 15 mm/s or

20 mm/s has been assumed with a proportional range of 2 mm.
Given a maximum positioning velocity of 15 mm/s the positioning
velocity amounts to approx. 11 mm/s with a control deviation of
1.5 mm and approx. 15 mm/s with a maximum positioning velocity of
20 mm/s.
The values may also be calculated arithmetically:
Amplification (G) = parameter .1.6. / parameter .1.3.
Correction velocity (VK) = control deviation * amplification (G)

Example 1: Example 2:
1
G = 15/2 = 7.5 /s G = 20/2 = 10.0 1/s
VK = 1.5 mm * 7.5 1/s VK = 1.5 mm * 10.0 1/s
VK = 11.25 mm/s VK = 15.0 mm/s

If the positioning velocity is too high the web guider will begin to oscil-
late.
The maximum positioning velocity must be set higher than the
maximum error velocity, yet must not exceed the nominal posi-
tioning velocity the DC actuator.

.1.7. velocity pos

The positioning velocity is determined in this parameter for the follo-
wing operating modes:
- actuator "center position"
- support beam "park sensor"
- support beam"search for edge"
The step width of the speed setting is 1 mm/s.

.1.8. velocity jog

The positioning velocity with which the actuator or support beam is
positioned in "manual" mode may be set in this parameter with a step
width of 1 mm/s.

U Page 31

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

.1.9. velocity defect

".2.2. defect range ±"
Switching threshold So that, in the event of a web displacement (e.g. seam joint) the ac-
for reducing the po- tuator no longer follows up at maximum positioning velocity in "auto-
sitioning velocity
matic" mode, the positioning velocity may be reduced to a required
".1.9. velocity value.
emergence"
Value of the re- From which degree of control deviation (web offset) onwards the re-
duced posi- duction is activated, must be set in parameter ".2.2. defect range ±" .
tioning velocity
In the case of a support beam this velocity setting is determined in
"search for edge" mode.
This parameter is only active if "defect detection" is selected in pa-
rameter .9.7..

Web edge progression in

the sensor

.2.0. derated velocity

Not assigned at present.

.2.1. reseved 21
Not assigned at present.

.2.2. defect range ±

If the set value is exceeded, the positioning velocity will be reduced to
the value set in parameter ".1.9. velocity defect". In the event of a
sudden web displacement (seam joint) this prevents the actuator fol-
lowing up at maximum positioning velocity which might lead to a web
tear.
This parameter is only active if "defect detection" is selected in pa-
rameter .9.7. .

.2.3. servo configuration

Parameter block for setting the motor data.

U Page 32

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

.2.4. motion direction

The positioning direction of the DC actuator drive may be inverted via
this parameter.
Following inversion of the positioning direction an initialisation run
must be performed.

.2.5. motion range total

The actual positioning path (dimension K) covered by the actuator at
the outfeed (transfer roller) must be entered in this parameter. As on
certain actuators (e.g. pivoting frames) the actuator positioning path
is not identical to that of the DC actuator drive, the exact value must
be entered.
The mechanical ratio (".3.7. mech. gear factor") is determined via this
setting during the initialisation run and the motor gear constant calcu-
Transfer rol- lated. The latter effects the normalisation of the positioning speed
ler and path.

.2.6. positonrange +
.2.7. positionrange -
Via the position range limit the DC actuator drive is prevented from
reaching its mechanical spindle stop or the actuator its mechanical
stop.
On compact systems the maximum actuator positioning path (see
parameter ".2.5. total motion range") is shortened at the factory by
approx. 2 mm. In the case of on-site mounting of the DC actuator
drive the position range limit must be set by the customer.
Especially in the case of large moved masses, please ensure that the
actuator does not come to a standstill at once. The positioning range
must be reduced accordingly.
The set values are always in relation to the set center.
The positioning path must entered for both sides (right/left) of the
center position in parameter .2.6. and .2.7. of the positioning range.
These position range limits must not be used as safeguards for
persons or appliances. For the safety of persons or appliances the
end position limits must be fitted with additional limit switches or a
suitable mechanical stop.

.2.8. alarm limit %

If necessary a range may be defined that, once exceeded, triggers
the output of a limit alarm. The value is entered in % and is in relation
to the two parameters ".2.6. positionrange +" and ".2.7. positionrange
-". If the actuator exceeds this calculated value the "end position ex-
ceeded" message is output. The end position early warning is always
in relation to the center of the positioning range. The warning is out-
put for both sides (positive and negative).

U Page 33

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

Example:
Entered value in parameter .2.8. = 75 %
Entered value in parameter .2.6. / .2.7. = 15 mm
15 mm * 75 / 100 = 11.25 mm
If the positioning range of 11.25 mm is exceeded the end position ex-
ceeded message will be output.
.2.6. = 15 mm .2.7. = 15 mm

11.25 mm end position

early warning in relation
to theoretical center

If the values differ in parameters .2.6. / .2.7. a theoretical center will

be deduced from the sum of the two values. The end position early
warning is in relation to this center.
Example:
Entered value in parameter .2.8. = 75 %
Entered value in parameter .2.6. = 15 mm
.2.6. = 15 mm .2.7. = 10 mm Entered value in parameter .2.7. = 10 mm
9.375 mm end position (15 mm + 10 mm) / 2 * 75 / 100 = 9.375 mm
early warning in relation
to theoretical center

.2.9. reserved 29
Not assigned at present.

.3.0. reference offset

In this parameter the distance between the reference switch switching
point and the center of the DC actuator drive is set.
To calibrate the internal position counter the actuator moves first to
the reference switch, then center position (neutral position) in "center
position" operating mode .
To assure that the positioning movement is as slight as possible in
"center position" mode the reference switch switching point should be
the same as neutral position.
This parameter is automatically determined and entered during the
actuator initialisation run.

U Page 34

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

DC actuator drive center

.3.1. center offset
Center
What is termed the "center offset" is the difference between the DC
offset
actuator drive center and the actuator neutral position. If this neutral
position deviates from the positioning path center the former may be
changed by entering the "center offset". In the case of a pivoting fra-
me, neutral position means that the positioning roller is parallel to the
guide roller.
If the guider is in "center position" mode while the "center offset" is
changed, the change of parameter value will be performed immedia-
tely by the DC actuator drive. Checking of the actuator neutral positi-
Actuator neutral position on is possible at once.

.3.2. system offset

If the DC actuator is located in the center of its positioning range the
actual position value "0" will be transmitted via the CAN bus. For spe-
cial applications an offset value may be set in this parameter which is
added to the transmitted actual position value.

.3.3. total resolution

The motor gear constant is displayed in this parameter. It is calcula-
ted on the basis of the following four parameters:
.3.4. encoder resolution, .3.5. rotation gear, .3.6. linear gear,
.3.7. mech. gear factor;

.3.4. encoder resolution

.3.5. rotation gear
.3.6. linear gear
.3.7. mech. gear factor
The motor gear constant is calculated via these parameters.

DC actuator drive se- Outfeed point

curing point

Center of
rotation
.3.4. .3.5. .3.6. .3.7.
encoder rotation linear mech.
resolution gear gear gear factor
S 2/S 1

.3.3. total resolution

U Page 35

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

The values for the three parameters .3.4./.3.5./.3.6. must be determi-

ned using the table in chapter 6.

The mechanical ratio is specified in parameter ".3.7. mech. gear fac-

tor".
The ratio may be established as follows:
Measure distance S 1 between the center of rotation and DC actua-
tor drive securing point. Equally, measure distance S 2 between the
center of rotation and the outfeed point. These two values are set in
relation to one another and the value calculated produces the me-
chanical ratio (parameter .3.7.).
Example:
measured distance S 1 450 mm
measured distance S 2 850 mm
850 mm / 450 mm = 1.89
In this example the entry in parameter .3.7. is 1.89.
During the initialisation run (parameter ..3. / Wert 10) parameter
".3.7. mech. gearfactor" is established automatically.

U Page 36

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

.3.8. reserved 38
Not assigned at present.

.3.9. reserved 39
Not assigned at present.

.4.0. pos. controlling

Parameter block for setting the positioning control loop.

.4.1. pos prop ±

If the position error is greater than the set "position controller propor-
tional range" the correction velocity will thus correspond to the maxi-
mum positioning velocity. If the position error is within the set "positi-
on controller proportional range" a lesser positioning velocity accor-
ding to the one of the characteristic curves is produced.
Via this parameter the P component of the actuator drive position
controller is indirectly set.

Example:
A web set position deviation of 1 mm produces an actuator set positi-
Positioning velocity on of 15 mm based on the set values (parameter .1.3. und .4.5.).
The DC actuator drive covers the first 10 mm at maximum positioning
velocity as these values are outwith the grey range. Once the 10 mm
are passed, only 5 mm remain. These 5 mm lie within the grey range
Position
error and the velocity is thus reduced linearly to 0 until the 15 mm position
range is reached.
In the case of uneven edges (textile) this parameter may be
increased to dampen the DC actuator drive position controller. The
static precision of the web guider is hereby preserved.
Position con-
Maximum posi- troller propor-
The value of parameter .4.1. should amount at most to half of the
tioning velocity tional range sensor scanning range.
in automatic (Parameter
(parameter .4.1.)
.1.6.) .4.2. act position
The actual position of the actuator at the outfeed, in relation to the set
center, is displayed.

.4.3. set position

The set position of the actuator at the outfeed, in relation to the set
center, is displayed.

U Page 37

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

.4.4. pos source adress

In the case of follow-up controlling (master/slave) a second actuator
(slave) without sensor scanning precisely follows up a freely selecta-
ble actuator (master). The device address of the master's guider must
be entered on the controller card of the second actuator (slave).
Master Slave
address address Example:
1.5 2.5 The master's address is 1.5
The slave's address is 2.5
Value 15 (address 1.5) must be entered in parameter .4.4. of the sla-
ve controller card (address 2.5).

.4.5. prop stroke ±

In the case of integral actuators the correction path is set in relation
to the set proportional range (parameter ".1.3. prop range ±").
This parameter has no function for proportional actuators.
The greater the set correction path is for a constant proportional ran-
ge (parameter ".1.3. prop range ±"), the greater the amplification
(steep characteristic curve) of the web guider in automatic mode.
The steeper the characteristic curve the longer the correction path in
the event of a control deviation and thus the more sensitive the sy-
stem will become. The correction path used by the actuator to try to
correct an error may be seen in the characteristic curve.

U Page 38

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

Correction path
Proportional range
established cor- .1.3. prop range ±
rection posi- 2,0
tioning path de-
pending on the
correction posi- 15 mm
tioning path 11 mm

Control deviation Correction path

.4.5. prop stroke ±
15 mm
20 mm

Set position
(Sensor measuring Control deviation of
range center ) 1.5 mm

In this example a maximum correction path of 15 mm or 20 mm was

set with a proportional range of 2 mm.
Given a correction path of 15 mm (20 mm) the correction path is ap-
prox. 11 mm (15 mm) given a control deviation of 1.5 mm.
The values may also be calculated arithmetically:
Amplification (G) = parameter .4.5. / parameter .1.3.
Correction path = control deviation * amplification (G)
Example 1: Example 2:
G = 15/2 = 7.5 G = 20/2 = 10.0
VK = 1.5 mm * 7.5 VK = 1.5 mm * 10.0
VK = 11.25 mm VK = 15.0 mm

U Page 39

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

.4.6. photo auto offset

With a follow-up control/tool control the actuator follows up the actual
web position proportionally.
To specify the required set postion of the unwinder/tool the offset bet-
ween the "center" position and the required set position must be en-
tered.
During the actuator initialisation run the offset is set to zero.
Manual offset specification:
Center position
The entry of the offset value is in 1/10 mm. Depending on the pre-
sign of the entry the set position of the actuator will be displaced to
the right or left of the center position.
Automatic offset specification:
In the case of automatic specification the web must be located in the
sensor scanning range and the actuator manually moved to the re-
quired set position. The offset is calculated and saved via the "setup"
and "automatic" key combination.

.4.6. photo auto

offset

Center position

Actuator set position

.4.7. speed controller

Parameter block for setting the speed controller.

.4.8. max. motor speed

The motor speed at maximum terminal voltage (22 V) is set here.
The speed value may be found in the table in chapter 6. The speed
value is set at 22 V motor voltage.

.4.9. act. speed

The actual motor speed of the DC actuator at that moment is display-
ed .

.5.0. speed_P; .5.1. speed_I

Please refer to the table in chapter 6 for the P and I components of
the various device types.
The values must not be changed. They have already been optimised
at the factory.
A change to these 2 parameters impairs the optimum function of
the guider. A change to these values may range from guiding im-
pairment to the system ceasing to function.

U Page 40

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

.5.2. accel. time

Positioning Positioning
velocity This function is only possible in "manual offset" mode.
velocity without
ramp function In manual mode the actuator is positioned with the positioning veloci-
ty set in parameter ".1.8. velocity jog".
With this ramp function ".5.2. accel. time" an acceleration time of 0 to
the maximum motor speed may be entered. The actuator drive thus
Time reaches its maximum motor speed after a set time. The motor speed
is increased linearly. Equally, the actuator comes to a standstill after
the same ramp function.
Positioning
velocity with
In the fig. opposite the motion speed progression of an actuator is
ramp function displayed with a set ramp function of 3 seconds. The key for the ma-
nual offset has been pressed for 5 seconds in this example. The bro-
ken line progression indicates the positioning velocity progression wit-
hout ramp function.

.5.3. I-PWM
The actual I-PWM value (pulse-width-modulated) is displayed. The
display is only of significance for internal tests.

.5.4. reserved 54
Not assigned at present.

.5.5. current controller

Parameter block for setting the current controller.

.5.6. cut-off current

Once the set value is exceeded the motor output stage is switched
off. This value should be twice as much as the motor nominal current
(parameter ".5.7. motor current").
Error display 3 is output as error in parameter ".6.9. system error".
If the current fails to reach the set value the motor output stage will
be re-enabled.

.5.7. motor current

The motor nominal current specified on the DC actuator drive type
plate should be set here. If set too high the motor current may over-
load or even destroy the DC actuator drive. Please also refer to the
table in chapter 6 in order to establish the current value.

U Page 41

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

.5.8. dyn. currentfactor

.5.9. term. timeconst.
.6.0. limited current
This time-limited excess current is used to increase the dynamics of
the DC actuator drive (shorter acceleration time)
For a short time a DC actuator drive may be operated with a higher
motor current. The factor is determined here. The internal current li-
mit is calculated on the basis of the nominal motor current in parame-
ter ".5.7. motorcurrent" and the factor from parameter ".5.8. dyn. cur-
rentfactor". The duration of the excess current is set in parameter
".5.9. therm. timeconst.".
Excess current functions according to the following principle:

Current
in mA Pos. 1 Pos. 2

internal cur-
rent limit
actual permissi-
ble motor cur-
rent
nom. motor current
motor current

Time
in s

If the motor current input is less than the nominal motor current the
permissible motor current will be increased within the set time (.5.9.
term. timeconst.) to the internal current limit. This actual permissible
motor current is displayed in parameter ".6.0. limited current".
If the motor current input (pos. 1) is greater than the nominal motor
current (.5.7. motor current) the permissible motor current will then
be reduced again within the set time (.5.9. term. timeconst.) to the
nominal motor current. As soon as the motor current is again drops
below the nominal motor current (pos. 2) increasing of the current li-
mit is resumed.
Once the operating voltage is supplied the permissible motor cur-
rent begins at the nominal motor current.
The current limit is upwardly limited by the maximum output stage
current (see technical data).

.6.1. act. current

The actual motor current of the DC actuator drive is displayed.

U Page 42

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

.6.2. current_P; .6.3. current_I

The P and I components of the current controller may be found in the
table in chapter 6.
The values may not be changed. The values are already optimised at
the factory.
Changing these 2 parameters impairs optimum guider operation.
Changing these values may result in guiding impairment to loss of
system function.

.6.4. set current

The current internal set current is displayed. Only of significance for
E+L service personnel.

.6.5. reserved 65
Not assigned at present.

.6.6. reserved 66
Not assigned at present.

.6.7. reserved 67
Not assigned at present.

.6.8. diagnostics
Parameter block for displaying the system status.

.6.9. system error

The following error messages are possible:
1 = supply voltage under 20 V DC
2 = supply voltage over 30 V DC
3 = the guider cut-off current has been exceeded
4 = the heat sink temperature is over 70°
5 = the incremental encoder is defective
6 = the incremental encoder is inverted (signal lines confused)
7 = no message from the right sensor
8 = no message from the left sensor
10 = the motor line is interrupted
12 = the motor output stage is defective
13 = the motor is blocked at maximum motor current
14 = several reference switch switching points
15 = the end position proximity switches are confused
16 = the external voltage supply of the control card is overloaded for
further attached devices.

U Page 43

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

.7.0. reserved 70
Not assigned at present.

.7.1. reserved 71
Not assigned at present.

.7.2. running time meter

The operating hours of the control card are displayed here.

.7.3. supplyvoltage 24 DC
The current supply voltage of the controllercard is displayed.

.7.4. temperature case

The current temperature of the controller card case is displayed here.

.7.5. temp. case max.

The controller card stores the highest measured temperature of the
heat sink. This stored temperature is displayed.

.7.6. reserved 76
Not assigned at present.

.7.7. reserved 77
Not assigned at present.

.7.8. mainloops/sec.
For internal evaluations only.

.7.9. I/O confugiration

Parameter block for programming the digital inputs.

.8.0. digi input status

The current status of the digital controller card inputs is displayed
here.

.8.1. reserved 81
Not assigned at present.

U Page 44

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

.8.2. usage input X 4.1

.8.3. usage input X 4.4
.8.4. usage input X 4.7
.8.5. usage input X20.2
.8.6. usage input X 3.2
The digital inputs (see wiring diagram) may be assigned functions.
Each function may only be assigned once.
The following table illustrates the possible function options:

Value Application Signal at active input

0 no usage no function of this input
1 Motor lock motor is stopped in each operating mode
-1 Motor unlock motor is enabled in each operating mode
2 Automatic lock motor is only stopped in automatic mode
-2 Automatik unlock motor is only enabled in automatic mode
3 Reference with speed- reference switch switches at negative motor direction of rotation (see example 1)
-3 Reference with speed+ reference switch switches at positive motor direction of rotation (see example 1)
4 Speed ± lock at signal 1 the motor direction of rotation is blocked. Which direction of rotation is inhi-
bited is only determined in conjunction with the reference switch. (see example 1)
-4 Speed ± unlock at signal 0 the motor direction of rotation is blocked. Which direction of rotation is inhi-
bited is only determined in conjunction with the reference switch. (see example 1)
5 Speed + lock at signal 1 the positive motor direction of rotation is stopped (see example 2)
-5 Speed + unlock at signal 0 the positive motor direction of rotation is stopped (see example 2)
6 Speed - lock at signal 1 the negative motor direction of rotation is stopped (see example 2)
-6 Speed - unlock at signal 0 the negative motor direction of rotation is stopped (see example 2)
7 Auto <-> Center switching-over between automatic and centering
-7 Center <-> Auto switching-over between centering and automatic
8 Oscillation ON oscillation ON
-8 Oscillation Off oscillation OFF
9 Weboffset Remote external web offset RE 1721 (only possible on terminal X 3.2!)
9- - not assigned
10 Webspeed Measure web speed measuring (only possible on terminal X 3.2!)
-10 - not assigned

Example 1:
The positioning range is to be limited by two series-connected break
contacts.
The inputs X 4.4 (reference switch) and X 4.7 (end positions) should
be assigned as follows:
Input X 4.4 is assigned the value -3. The switching point is reached
via the positive motor direction of rotation.
Input X 4.7 is assigned the value -4 (break contact).

U Page 45

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

Example 2:
The positioning range is to be limited by two separate break contacts.
The inputs X 4.4 and X 4.7 should be assigned as follows:
Input X 4.4 is assigned the value -6. At signal 0 the negative motor
direction of rotation is stopped.
Input X 4.7 is assigned the value -5. At signal 0 the positive motor di-
rection of rotation is stopped.
If the circuit is set up with make contacts, value 5 or 6 must be set.

.8.7. reserved 87
Not assigned at present.

.8.8. reserved 88
Not assigned at present.

.8.9. reserved 89
Not assigned at present.

.9.0. reserved 90
Not assigned at present.

.9.1. system config.

Parameter block for application adaptation.

U Page 46

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

.9.2. guider type

This parameter is used to determine which type of guider will be
used.

Proportional actuator Integral actuator Master-Slave Three-level mode

Pivoting frame Pivoting roller mode
Steering roller Segmented guide rollers
Turn rod Edge spreading device
Winding station Spreading device
Push roller Positioning control
Follow-up control

nact = actual speed

n = speed nset = set speed
nact = actual speed Sset actuator = actuator ∆S = web deviation ∆S = web deviation
nset = set speed set position Sist = actual position Sist = actual position
S = web set position Sact actuatr = actuator Ssoll = set position Ssoll = set position
∆S = web deviation actual position
Sact = actual position ∆S = web deviation
Sset = set position Sact web = actual web position
Sset web = set web position

0= on a proportional guider a specific motion speed is output to cor-

rect the guiding difference in the event of a deviation of the actual
position from the set position.
1= on an integral actuator a specific actuator position is output to cor-
rect the guiding difference.
2= in master slave mode a DC actuator (slave) exactly follows up
another DC actuator (master). This value 2 may only be set in the
control card for the slave.
3= for applications with an actuator with three-level action
(e.g. reversing contactor).

.9.3. control mode

In the case of web center guiding systems with motor-driven sensor
following-up (hybrid) value 1 must be set.

U Page 47

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

.9.4. auto address

The controller card features automatic sensor addressing.
Sensor addressing is only performed after a reset and is only pos-
sible for sensors that are directly connected to the controller card
at connectors X 5/X 6. Furthermore, the sensors must feature the
appropriate software for automatic sensor addressing.
The following sensor addressing options are possible.
0= The sensor address/es is/are only displayed in parameters
"connector X5" and "connector X6". The address is manually
set on the sensor or via the command device.
1= Device number 1 is automatically assigned to the sensor at ter-
minal X5 and device number 2 to the sensor at terminal X6. The
sensor device group is identical with the controller card group.
Address setting according to the sensor description is thus un-
necessary.
2= The sensor at terminal X5 (X6) is assigned the address set in
the "connector X5" ("connector X6) parameter. In the event of
sensor replacement (defective sensor) the new sensor is auto-
matically assigned the right address.

.9.5. CAN connector Right

.9.6. CAN connector Left
The address setting of the sensor at terminal X5 (X6) is displayed.

.9.7. >function config 1

Certain functions may be activated or deactivated.
The following table indicates the possible functions:

U Page 48

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

Function Value Description

[X] Framelimit Check 0001h Monitors both position range limits. This function must be switched of
on actuators without end positions (e.g. tube slitters)!
[ ] N~ / M control 0002h No function at present
[ ] Center direct 0004h In this case moving to center position is performed without additional
calibration of the position counter in "center position" operating mode.
[ ] Ref on PowerOn 0008h Once operating voltage is supplied the reference switch is first of all
approached in order to calibrate the position counter. Then the opera-
ting mode is selected that was set before the operating voltage was
switched off.
[ ] Watch webedge R 0010h In the motor-driven positioning of fork-type sensors the right web edge
is monitored. If the sensor scanning range is fully covered, motor-
driven positioning is interrupted. Damaging of the web edge by the
fork-type sensor is thus prevented.
[ ] Watch webedge L 0020h In the motor-driven positioning of fork-type sensors the left web edge
is monitored. If the sensor scanning range is fully covered, motor-
driven positioning is interrupted. Damaging of the web edge by the
fork-type sensor is thus prevented.
[ ] Photo on autokey 0040h The actual motor position is saved as the set position for automatic
mode. Displaying is in parameter ".4.6. photo auto offset". (see also
parameter ..3. / value 13
[ ] Sens. err.> Center 0080h In the case of an invalid sensor signal the actuator is moved to the
stored center position. If this function is not activated the actuator will
only be blocked in the event of an invalid sensor signal.
[ ] MCP active 0100h Activation of the MCP (MasterControleProcessor). If no controller card
is featured in a group with the address x.5 (master) this function must
therefore be set.
[ ] Auto. SensorFree 0200h Switching-off of all web guider applications.
[ ] Support 2 motor 0400h If on one support beam, two positioning carriages are featured that
are to be moved independently of one another, this function must be
selected for the purpose of collision monitoring. This function is auto-
matically set during support beam initialisation.
[X] Weboffset 1/10 mm 0800h On predecessor controller cards the web offset is always tranmitted in
1/10 mm. Controller card RK 4004 transmits in 1/100 mm. To assure
that controller card RK 4004 is compatible to older models this
function must be set .
[ ] Weboffset invers 1000h The effective direction of the web offset is inverted
[ ] Defect detection 2000h If the edge error exceeds the set proportional range (e.g. due to web
displacement, adhesive point, web tear etc) the motion speed is redu-
ced to the set motion speed in parameter ".1.9. velocity emergence".
[ ] ext. system mode 4000h The system mode is expanded for future applications. Various opera-
ting modes may then be performed simultaneously with the modified
command stations.
[ ] RE 1721 invert 8000h Turning the potentiometer in a clockwise direction (to the right) must
also effect a web offset to the right. If the web offset is in the opposite
direction (to the left) this function is used to invert the effective direc-
tion of the command station.

U Page 49

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

The functions may be directly selected with a CANMON program or

command station DO 200..
If these two options are not available the sum of the required
functions must be formed and this sum value entered in this parame-
ter. Sum formation must be performed in the hexa-decimal system.
Example 1:
The "Watch webedge R" and "Watch webedge L" functions are requi-
red.
Sum value = 0010h + 0020h = 0030h
Parameter value = 30

Example 2:
The "enable Photo" and "Sens. err.> Center" functions are required.
Sum value = 0040h + 0080h = 00A0h
Parameter value = A0

.9.8. function config 2

Certain functions may be activated or deactivated. The following table
illustrates the functions:
In the case of the curved brackets () only one function may be sel-
ected.

(*) no controller output 0000h None of the following 5 values is output via the CAN channel
( ) N-target -> CAN 0001h Output of the set speed value
( ) Delta N -> CAN 0002h Output of the speed difference
( ) Pos-target -> CAN 0003h Output of the set position value
( ) Delta Pos -> CAN 0004h Output of the position difference
( ) I-target -> CAN 0005h Output of the set current value
[ ] Disable I-Loop 0008h If no motor is connected to the controller card, this setting must be
used to switch off the current circuit.
[ ] Send targetpos. 0010h Instead of the DC actuator drive actual position the set position of the
DC actuator drive is transmitted as a CAN message. The following
losses with a follow-up controlling system are thus reduced.
[ ] lock webspeedlim 0020h If the set web speed fails to be reached (parameter 1.1.5.) automatic
mode is blocked.
[ ] Start AUTO slow 0040h If the web is outside of the proportional range when the operating
mode "automatic" is selected, the positioning speed will be reduced to
the positioning speed set for the manual mode. This reduction will be
made only once and it will be made after the "automatic" mode has
been selected.

The functions may be directly selected with a CANMON program or

command station DO 200. .
If these two options are not available the sum of the required
functions must be formed and this sum value entered in this parame-
ter.

U Page 50

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

Example :
The "I target-> CAN" and "Disable I Loop" functions are required.
Sum value = 0005h + 0008h = 000Dh
Parameter value = 000D

.9.9. operatorkey config

This parameter is used to activate or deactivate certain functions. The
table below lists the functions:

Function Value Description

[ ] Auto: use all sens 0001h In "automatic" mode all edge sensors featured in this group are selec-
ted.
[ ] Auto: take photo 0002h On selecting "automatic" mode a guiding photo (take photo) is trigge-
red.
[ ] force support free 0004h When the "park sensor" key is pressed or signal supplied to the input
of the same name on a digital interface the sensors are moved to their
outer position and main mode set to "SystemLocked". The system is
only enabled once the "park sensor" key is released or signal no lon-
ger supplied to the input of the same name on a digital interface.
[ ] Center: sup. free 0008h In "center position" mode the positioning carriages/sensors are moved
to their outer position. In "automatic" mode the positioning carriages/
sensors move to their origin position or in "hybrid" mode so that they
are symmetrical to the machine center.
[ ] unused sup. free 0010h In "automatic" mode non-selected sensors mounted on a motor-driven
positioning carriage, are moved to their outer position. (not active at
present)
[ ] Auto. SensorFree 0020h If, during "search for edge" mode the inner end position of the posi-
tioning carriage is reached, "park sensor" mode is automatically swit-
ched to. This value must be set in the controller card X.5 (Master). If
no controller card with address X.5 is featured, the function must be
set on the controller card with activated MCP (MasterControlProces-
sor) (see parameter .9.7. function config 1 / Wert 0100).
[ ] Sens sel. direct 0040h Without this setting "manual" mode will always be switched to when a
sensor is selected. If this function is set the selected operating mode
is retained when a sensor is selected.
[ ] emergency sensor L 0080h Emergency guiding with left sensor
[ ] emergency sensor R 0100h Emergency guiding with right sensor
(*) lost web ---- 0000h On the loss of the web edge no change to the operating mode is per-
formed.
( ) lost web: Center 1000h On the loss of the web edge "center position" mode is switched.
( ) lost web: Manual 2000h On the loss of the web edge "manual" mode is switched.

The functions may be selected directly with a CANMON program or

command station DO 200..
If these two options are not available the sum of the required
functions must be formed and this sum value entered in this parame-
ter.

U Page 51

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

Example 1:
The "Auto: use all sens" and "force support free" functions are requi-
red.
Sum value = 0001h + 0004h = 0005h
Parameter value = 5
Example 2:
The "Sens sel. direct", "emergency sensor L" and "emergency sensor
R" functions are required.
Sum value = 0040h + 0080h + 0100h = 01A0h
Parameter value = 1A0

1.0.0. reserved 100

Not assigned at present.

1.0.1. delaytime 1
1.0.2. delaytime 2
On the loss of the guiding criterion when a color line sensor an option
is available of switching to what is termed an emergency sensor.
Emergency guiding is activated in parameter ".9.9. operatorkey con-
fig". The periods after which switching-over takes place are set via the
two "delaytime" parameters.
Switching-over is performed according to the following principle:

Main sensor
(Color line sensor)

Emergency ensor
(Edge sensor)

Time

Status
Color line sensor valid invalid valid
.1.0.1 1.0.2.
Parameter delaytime delaytime
1 2
Operating mode automatic blocked automatic

Sensor selection dark line right edge sensor dark line

U Page 52

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

➀ At this point the color line sensor loses its guiding criterion. The
web guider is blocked and the delay time set in parameter "1.0.1.
delaytime 1" started.
➁ On expiry of the set time switching to the emergency sensor takes
place and the web guider is enabled. Automatic mode is continued.
At the same time the controller card adopts the current actual web
position as the set position for the emergency sensor.
➂ The guiding criterion is available again and the delay time in para-
meter "1.0.2. delaytime 2" starts. Guiding is still performed by
emergency sensor.
➃ Once the set time has elapsed the system switches back to the
color line sensor.

1.0.3. subsystem 0 address

1.0.4. subsystem 1 address
1.0.5. subsystem 2 address
1.0.6. subsystem 3 address
Controller card RK 40.. features a serial bus connection. Up to 4 mo-
dules (e.g. a command station, several logic cards etc.) may be seri-
ally connected via this serial bus. The addresses of the serial devices
are entered automatically in ascending order beginning in parameter
1.0.3., (1st slot = address in parameter 1.0.3., 2nd slot = address in
parameter 1.0.4. etc). In the event of double addressing, the address
must be changed in the appropriate parameter. The place in front of
the dot specifies the group number and the place after the dot the de-
vice number.
Example:
Device number: A 9 F C
Group number: 0 0 3 7
Entry in parameter 0.A 0.9 3.F 7.C

1.0.7. calibration
Parameter block for calibrating the controller card.

1.0.8. calib. UDC

Scaling of operating voltage measuring and display. This parameter is
automatically set during the test run at E+L.

1.0.9. offset. I-act

Motor current offset measuring. This parameter is automatically set
during the test run at E+L.

1.1.0. calib. I-act

Scaling of motor current measuring and display. This parameter is au-
tomaticallly set during the test run at E+L.

U Page 53

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

1.1.1. reserved 111

Not assigned at present.

1.1.2. webspeed config.

Parameter block for setting web speed measuring.

1.1.3. webspeed constant

In order to calibrate the web speed measuring function in the control-
ler card the no. of pulses that are generated per running meter of
the web must be entered here.

1.1.4. webspeed max.

1.1.5. webspeed limit
1.2.0. max webspeed ratio
1.2.1. lim webspeed ratio
These parameters are only significant if one of the four functions
is activated in parameter "1.1.8. adaptive function".
% factor The guider proportional range or actuator speed may be influenced
depending on the web speed.
The two vertexes for the characteristic curve are determined via the
following parameters. Depending on the current web speed, a per
1.2.1. cent factor is produced on the basis of the characteristic curve with
which the proportional range or motion speed may be influenced.
1.2.0. 1.1.4. = Entry of the maximum web speed
m/min 1.2.0. = Entry of the accompanying per cent value

1.1.5. 1.1.4.
1.1.5. = Entry of the minimum web speed
1.2.1. = Entry of the accompanying per cent value

Example 1:
The set proportional range (.1.3.) should be 200% at minimum web
speed and 50% at maximum web speed. The minimum web speed is
1.2.1. 15 m/min, the maximum web speed 60 m/min.
The corresponding per cent factor for the proportional range at a
1.2.0. specific web speed may be deduced from the characteristic curve
opposite.

1.1.5. 1.1.4.

U Page 54

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

Example 2:
The maximum positioning velocity in "automatic" mode (.1.6.) should
1.2.0. be 25% at minimum web speed and 100% at maximum web speed.
The minimum web speed is 5 m/min, the maximum web speed 20 m/
1.2.1. min.
The corresponding per cent factor for the positioning velocity at a
specific web speed may be deduced from the characteristic curve op-
1.1.5. 1.1.4. posite .

The reduction of the positioning velocity does not have any effect
on the sensitivity of the control loop.

1.1.6. actual webspeed

The actual web speed is displayed in m/min.

1.1.7. adaptive controle

Parameter block for process-dependent setting of the control parame-
ters.

1.1.8. adaptive function

An adaptive guider setting is available for adapting the web guider
control loop to changing process variables (e.g. web speed). Which
guider setting is to be influenced by which process variable must be
set with one of the following values.
0= Adaptive controlling without function.
1= The guider proportional range (.1.3.) is influenced depending
on an external CAN signal.
2= The guider proportional range (.1.3.) is influenced depending
on the web speed.
4= The motion speed in automatic mode (.1.6.) is influenced de-
pending on an external CAN signal.
8= The motion speed in automatic mode (.1.6.) is influenced by the
web speed.
16 = The positioning path (.4.5.) is influenced by an external CAN si-
gnal.
32 = The positioning path (.4.5.) is influenced by the web speed.

1.1.9. adaptive ratio

Display of the current control loop amplification.

1.2.0. max webspeed ratio

See parameter 1.1.4. .

1.2.1. lim webspeed ratio

See parameter 1.1.5. .
U Page 55

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

1.2.1. reserved 121

Not assigned at present.

1.2.2. reserved 122

Not assigned at present.

1.2.3. reserved 123

Not assigned at present.

1.2.4. reserved 124

Not assigned at present.

1.2.5. !! Service !!
This parameter serves only as a parameter title for the following pa-
rameters that are grouped together due to their function. The para-
meter itself has no function.

1.2.6. service off/on

For E+L service personnel only.
Service mode is started via value "1". Following a reset the value is
automatically reset to "0".

1.2.7. >service mode

For E+L service personnel only.
2= Square wave current controller test
3= Delta wave current controller test
4= Square wave speed controller test
5= Delta wave speed controller
6= Square wave PWM bridge signal
7= Delta wave PWM bridge signal
8= Square wave set position value
9= Delta wave set position value

1.2.8. testvalue 1
For E+L service personnel only.

1.2.9. testvalue 2
For E+L service personnel only.

1.3.0. testcycletime
For E+L service personnel only.

U Page 56

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

5.3 "Three position controller" For control card applications as a three position controller the va-
upgrade lue 32 must be entered in parameter "..3. start service" during
control card commissioning. This loads the three position control-
ler parameter record. The three position controller parameters that
differ from the norm are described below.

No. Name Default Min. Max. Unit Description

.1.3. puls range ± 2.0 0.0 2000.0 mm Switching threshold for transition
Stop at pulse output

.1.4. slow range ± 4.0 0.0 2000.0 mm Switching threshold for transition
Pulse output to permanent signal

.1.5. fast range ± 6.0 0.0 2000.0 mm Switching threshold for transition
Permanent signal to fast signal

.1.6. hysteresis 1.0 0.0 2000.0 mm Hysteresis of the individual switching thresholds

.1.7. pulse ON-time 1.0 0.0 10.0 sec Switch-on time of pulse signal

.1.8. pulse OFF-time 1.0 0.0 10.0 sec Switch-off time of pulse signal

.1.9. jog with fast 0 0 1 Jog mode with fast signal

.2.0. dig. I/O adress 0 0 7.F hex Address of digit. output card for the positioning signals

.2.1. • act. control out Display of the current positioning signal

.1.3. puls range ± (switching threshold 1)

.1.4. slow range ± (switching threshold 2)
.1.5. fast range ± (switching threshold 3)
The three position controller software features 3 switching thresholds.
Switching threshold 1pulsed "Right" or "Left" output
Switching threshold 2 "Right" or "Left" output duration
Switching threshold 3 "Fast" output duration

The "Fast" output is switched to threshold 2.

Output: The switching thresholds should be entered in the appropriate para-
"Right" meters. The entered value corresponds to the unit mm .
"Left" If a switching point is not required, the value "0" must be set in the
"Fast" appropriate parameter.

U Page 57

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

No hysteresis set: .1.6. hysteresis

on and off switching point at A hysteresis may be set for the three existing switching thresholds
0.4 mm
(pulsed, continuous and fastl). The hysteresis allows the switching-off
point to lie below the switching-on point by the amount of the hystere-
sis.
The set value is applicable to all three switching thresholds.
The hysteresis must not be set higher than the smallest distance
between two switching thresholds or from one switching threshold
Hysteresis of 0.1 set: to "0".
Switch-on point at 0.4 mm and
switch-off point at 0.3 mm

.1.7. pulse ON-time

.1.8. pulse OFF-time
The switch-on and off duration may be set separately for switching
Switch-on duration
parameter .1.7. threshold 1 (parameter ".1.3. pulse range ±"). The switch-on duration
is entered in parameter .1.7. and the switch-off duration in parameter
.1.8. .

Switch-off duration
parameter .1.8.

.1.9. jog with fast

In jogging mode the fast ouput may be additionally switched to the left
or right output. The value "1" must be entered in order to activate the
fast output.

.2.0. dig. I/O address

The device address of logic card LK 4203 must be entered here to
the output signals "Left", "Right" and "Fast". The address is specified
in the block diagram.
In logic card LK 4203 the value 15 (3 position controller) must be
set in parameter "..5. >IO card usage".

.2.1. act. control out

The current positioning signal is displayed for internal purposes.

U Page 58

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

6. Setting values
Type Mat. No. Pulse Trans- Spindle Watts Pos. Current Nominal Speed Speed Current Current
per rev mission pitch path speed
at 22 V P I P I
.3.4. .3.5. .3.6. .5.7. .4.8. .5.0. .5.1. .6.2. .6.3.
AG 2491 201444 8 8:1 4 20 12 0,86 3300 2,0 0,10 2,6 0,4
AG 2491 204474 8 8:1 4 20 25 0,86 3300 2,0 0,10 2,6 0,4
AG 2491 210667 8 8:1 4 20 50 0,86 3300 2,0 0,10 2,6 0,4
AG 2571 311963 8 8:1 5 40 25 2,9 2750 2,0 0,10 2,6 0,4
AG 2571 311941 8 20,25:1 5 40 25 2,9 2750 2,0 0,10 2,6 0,4
AG 2571 311964 8 8:1 5 40 50 2,9 2750 2,0 0,10 2,6 0,4
AG 2571 311942 8 20,25:1 5 40 50 2,9 2750 2,0 0,10 2,6 0,4
AG 2571 311965 8 8:1 5 40 75 2,9 2750 2,0 0,10 2,6 0,4
AG 2571 311966 8 20,25:1 5 40 75 2,9 2750 2,0 0,10 2,6 0,4
AG 2571 311804 8 8:1 5 40 100 2,9 2750 2,0 0,10 2,6 0,4
AG 2571 311943 8 20,25:1 5 40 100 2,9 2750 2,0 0,10 2,6 0,4
AG 2591 229159 8 8:1 5 40 15 2,9 2750 2,0 0,10 2,6 0,4
AG 2591 210896 8 8:1 5 40 25 2,9 2750 2,0 0,10 2,6 0,4
AG 2591 210897 8 8:1 5 40 50 2,9 2750 2,0 0,10 2,6 0,4
AG 2591 217908 8 20,25:1 5 40 50 2,9 2750 2,0 0,10 2,6 0,4
AG 2591 210898 8 8:1 5 40 75 2,9 2750 2,0 0,10 2,6 0,4
AG 2591 227057 8 20,25:1 5 40 75 2,9 2750 2,0 0,10 2,6 0,4
AG 2591 230119 8 20,25:1 5 40 100 2,9 2750 2,0 0,10 2,6 0,4
AG 2591 219860 8 8:1 5 40 100 2,9 2750 2,0 0,10 2,6 0,4
AG 2593 230661 8 1:1 4 120 12 2 1228 2,0 0,10 2,6 0,4
AG 2593 234536 8 1:1 4 120 50 2 1228 2,0 0,10 2,6 0,4
AG 2593 310696 8 1:1 5 120 75 2 1228 2,0 0,10 2,6 0,4
AG 2595 226921 8 8:1 5 40 24 2,9 2750 2,0 0,10 2,6 0,4
AG 2596 227183 8 8:1 5 40 40 2,9 2750 2,0 0,10 2,6 0,4
AG 2671 311967 8 16:1 5 80 25 4,9 3070 2,0 0,10 2,6 0,4
AG 2671 311946 8 28:1 5 80 25 4,9 3070 2,0 0,10 2,6 0,4
AG 2671 311944 8 16.1 5 80 50 4,9 3070 2,0 0,10 2,6 0,4
AG 2671 311947 8 28:1 5 80 50 4,9 3070 2,0 0,10 2,6 0,4
AG 2671 310208 8 16:1 5 80 75 4,9 3070 2,0 0,10 2,6 0,4
AG 2671 311948 8 28:1 5 80 75 4,9 3070 2,0 0,10 2,6 0,4
AG 2671 311945 8 16:1 5 80 100 4,9 3070 2,0 0,10 2,6 0,4
AG 2671 311949 8 28:1 5 80 100 4,9 3070 2,0 0,10 2,6 0,4
AG 2671 311807 8 16:1 5 80 150 4,9 3070 2,0 0,10 2,6 0,4
AG 2671 311950 8 28:1 5 80 150 4,9 3070 2,0 0,10 2,6 0,4
AG 2691 224526 8 4:1 5 80 50 4,9 3070 2,0 0,10 2,6 0,4
AG 2691 212610 8 16:1 5 80 50 4,9 3070 2,0 0,10 2,6 0,4
AG 2691 229098 8 28:1 5 80 50 4,9 3070 2,0 0,10 2,6 0,4
AG 2691 212609 8 16:1 5 80 75 4,9 3070 2,0 0,10 2,6 0,4
AG 2691 228765 8 28:1 5 80 75 4,9 3070 2,0 0,10 2,6 0,4
AG 2691 312204 8 34,5:1 5 80 100 7,5 2750 2,0 0,10 2,6 0,4
AG 2691 217808 8 16:1 5 80 100 4,9 3070 2,0 0,10 2,6 0,4
AG 2691 212325 8 28:1 5 80 100 4,9 3070 2,0 0,10 2,6 0,4
AG 2691 234946 8 4:1 5 80 175 4,9 3070 2,0 0,10 2,6 0,4
AG 2691 228283 8 28:1 5 80 175 4,9 3070 2,0 0,10 2,6 0,4
AG 2691 214554 8 16:1 5 80 175 4,9 3070 2,0 0,10 2,6 0,4
AG 4081 208615 8 6,25:1 2,5 9,5 25 0,71 2778 0,4 0,01 2,6 0,4
AG 4081 208616 8 6,25:1 2,5 9,5 6 0,71 2778 0,4 0,01 2,6 0,4
AG 4081 226862 8 6,25:1 2,5 9,5 50 0,71 2778 0,4 0,01 2,6 0,4
AG 4091 209822 8 6,25:1 2,5 9,5 6 0,71 2778 0,4 0,01 2,6 0,4
AG 4481 308422 500 1:1 2,5 9 12 0,9 1746 2,0 0,10 2,6 0,4
AG 4481 308498 500 1:1 2,5 20 30 0,9 1746 2,0 0,10 2,6 0,4
AG 4571 311968 8 8:1 5 40 25 2,9 2750 2,0 0,10 2,6 0,4
AG 4571 311952 8 20,25:1 5 40 25 2,9 2750 2,0 0,10 2,6 0,4

U Page 59

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

Type Mat. No. Pulse Trans- Spindle Watts Pos. Current Nominal Speed Speed Current Current
per rev mission pitch path speed
at 22 V P I P I
.3.4. .3.5. .3.6. .5.7. .4.8. .5.0. .5.1. .6.2. .6.3.
AG 4571 311805 8 8:1 5 40 50 2,9 2750 2,0 0,10 2,6 0,4
AG 4571 311953 8 20,25:1 5 40 50 2,9 2750 2,0 0,10 2,6 0,4
AG 4571 311951 8 8:1 5 40 75 2,9 2750 2,0 0,10 2,6 0,4
AG 4571 311954 8 20,25:1 5 40 75 2,9 2750 2,0 0,10 2,6 0,4
AG 4571 311806 8 8.1 5 40 100 2,9 2750 2,0 0,10 2,6 0,4
AG 4571 311955 8 20,25:1 5 40 100 2,9 2750 2,0 0,10 2,6 0,4
AG 4591 230566 8 8:1 5 40 25 2,9 2750 2,0 0,10 2,6 0,4
AG 4591 232466 8 20,25:1 5 40 25 2,9 2750 2,0 0,10 2,6 0,4
AG 4591 307757 8 20,25:1 5 40 50 2,9 2750 2,0 0,10 2,6 0,4
AG 4591 230657 8 8:1 5 40 50 2,9 2750 2,0 0,10 2,6 0,4
AG 4591 230568 8 8:1 5 40 75 2,9 2750 2,0 0,10 2,6 0,4
AG 4591 229330 8 20,25:1 5 40 75 2,9 2750 2,0 0,10 2,6 0,4
AG 4591 229329 8 8:1 5 40 100 2,9 2750 2,0 0,10 2,6 0,4
AG 4591 230136 8 20,25:1 5 40 100 2,9 2750 2,0 0,10 2,6 0,4
AG 4671 311969 8 11:1 5 80 25 4,9 3070 2,0 0,10 2,6 0,4
AG 4671 311958 8 25,14:1 5 80 25 4,9 3070 2,0 0,10 2,6 0,4
AG 4671 311956 8 11:1 5 80 50 4,9 3070 2,0 0,10 2,6 0,4
AG 4671 311959 8 25,14:1 5 80 50 4,9 3070 2,0 0,10 2,6 0,4
AG 4671 311808 8 11:1 5 80 75 4, 3070 2,0 0,10 2,6 0,4
AG 4671 311960 8 25,14:1 5 80 75 4,9 3070 2,0 0,10 2,6 0,4
AG 4671 311957 8 11:1 5 80 100 4,9 3070 2,0 0,10 2,6 0,4
AG 4671 311961 8 25,14:1 5 80 100 4,9 3070 2,0 0,10 2,6 0,4
AG 4671 311809 8 11:1 5 80 150 4,9 3070 2,0 0,10 2,6 0,4
AG 4671 311962 8 25,14:1 5 80 150 4,9 3070 2,0 0,10 2,6 0,4
AG 4691 230562 8 11:1 5 80 25 4,9 3070 2,0 0,10 2,6 0,4
AG 4691 230563 8 11:1 5 80 50 4,9 3070 2,0 0,10 2,6 0,4
AG 4691 230564 8 11:1 5 80 75 4,9 3070 2,0 0,10 2,6 0,4
AG 4691 230565 8 11:1 5 80 100 4,9 3070 2,0 0,10 2,6 0,4
AG 4691 230135 8 25,14:1 5 80 100 4,9 3070 2,0 0,10 2,6 0,4
AG 4699 309000 8 11:1 6 80 1090 4,9 3070 2,0 0,10 2,6 0,4
DR 1111 500 1:1 2,5 20 10 0,9 1746 1,0 0,02 2,6 0,4
DR 1272 500 1:1 2,5 20 10 0,9 1746 1,0 0,02 2,6 0,4
DR 2472 500 1:1 2 80 10 3,3 3475 2,0 0,10 2,6 0,4
DR 2472 500 1:1 2 80 15 3,3 3475 2,0 0,10 2,6 0,4
DR 2472 500 1:1 2 80 20 3,3 3475 2,0 0,10 2,6 0,4
VE 5016 8 8:1 5 40 350 2,9 2750 2,0 0,10 2,6 0,4
VE 5016 8 8:1 5 40 350 2,9 2750 2,0 0,10 2,6 0,4
VG 18 8 64:1 4 80 55 2,95 1897 2,0 0,10 2,6 0,4
DR 52 8 8:1 5 40 17-25 2,9 2750 2,0 0,10 2,6 0,4
VS 50 8 64:1 125 35 without 2,7 3300 2,0 0,10 2,6 0,4
VS 60 8 288:1 300 30 without 2,7 3300 2,0 0,10 2,6 0,4
VS 35 10 46:1 77 20 without 0,8 1870 2,0 0,10 2,6 0,4
VS 35 10 46:1 77 20 without 0,8 1870 2,0 0,10 2,6 0,4
VS 45 10 50:1 78 6 without 0,71 2778 2,0 0,10 7,0 0,1
VS 90 8 16:1 5 80 without 4,9 3070 2,0 0,10 2,6 0,4
BC 1103 8 8:1 5 40 19 2,9 2750 2,0 0,10 2,6 0,4
BT 25 8 16:1 100,0 80 without 4,9 3070 2,0 0,10 2,6 0,4
DR 2272 500 1:1 2,5 20 10 0,9 1746 2,0 0,10 2,6 0,4

U Page 60

Downloaded from www.Manualslib.com manuals search engine

 Digital controller RK 4004

Operating voltage
7. Technical Nominal value 24 V DC
data Nominal range 20 - 30 V DC
(including ripple)
Power input
without motor/sensors 4,8 W
with motor (maximum) 180 W
Current input
without motor/sensors 0,2 A
with motor (maximum) 7.2 A
Output voltage
at motor terminal ±22 V (PWM)
(PWM=pulse width-modulated)
Maximum output current 7A
Protection class IP 00

CAN bus
CAN bus level + 5 V (potential-free)
CAN baud rate 250 KBaud

Sound level digital inputs

terminal X 4.1 / 4.4 / 4.7 / 20.2 / 3.2
Low "0" 0 to 3 V DC
High"I" 10 to 30 V DC
Incremental encoder frequency maximum 5 kHz

Digital output terminal X 20.4

Output current maximum 0.1 A
PNP

Sensor connector X 5/X 6

Output voltage 24 V DC
Output current maximum 0.5 A
Technical data subject to modification without notice

U Page 61

Downloaded from www.Manualslib.com manuals search engine

 Erhardt + Leimer GmbH
Post box 10 15 40
D-86136 Augsburg
Telephone (0821) 24 35-0
Telefax (0821) 24 35-666

Downloaded from www.Manualslib.com manuals search engine