Scribd
Upload
215 views1 page

DTC P0121 Throttle/Pedal Position Sensor/Switch "A" Circuit Range/Performance Problem

The document summarizes information about diagnostic trouble code P0121 related to the throttle/pedal position sensor/switch circuit. It provides details on the purpose of the throttle position sensor, the circuit description, monitor description, strategy, enabling conditions, and typical malfunction thresholds. The monitor checks that the throttle position sensor output is within the proper range when the throttle valve is closed, and a P0121 code is set if it is not within 7.4-26.2 degrees.

Uploaded by

Clodoaldo Biassio
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
215 views1 page

DTC P0121 Throttle/Pedal Position Sensor/Switch "A" Circuit Range/Performance Problem

The document summarizes information about diagnostic trouble code P0121 related to the throttle/pedal position sensor/switch circuit. It provides details on the purpose of the throttle position sensor, the circuit description, monitor description, strategy, enabling conditions, and typical malfunction thresholds. The monitor checks that the throttle position sensor output is within the proper range when the throttle valve is closed, and a P0121 code is set if it is not within 7.4-26.2 degrees.

Uploaded by

Clodoaldo Biassio
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

05–94

DIAGNOSTICS – SFI SYSTEM (April, 2003) 052NE–14

DTC P0121 THROTTLE/PEDAL POSITION


SENSOR/SWITCH ”A” CIRCUIT
RANGE/PERFORMANCE PROBLEM
HINT:
This is the purpose of the ”throttle position sensor”.
CIRCUIT DESCRIPTION
Refer to DTC P0120 on page 05–87.
DTC No. DTC Detection Condition Trouble Area
The following condition is met 4 times. After the vehicle speed
has exceeded 19 mph (30 km/h) once, the throttle position
P0121  Throttle position sensor (built in throttle body)
sensor output value is out of normal range when the throttle
valve is closed at 0 km/h

MONITOR DESCRIPTION
The throttle position sensor varies its resistance with the angle of the throttle valve. The ECM applies a regu-
lated reference voltage to the throttle position sensor “+” terminal and calculates the angle of the throttle
valve based on the voltage present at the throttle position sensor “signal” terminal.
When the throttle valve is near the fully closed position, the output voltage of the throttle position sensor is
low. When it is near the fully open position, the output voltage is high.
The ECM checks the indicated angle of the throttle valve during “stop and go” conditions. If the indicated
angle (or voltage) in the “closed throttle” position is out of the specified range, the ECM interprets this as a
malfunction in the throttle position sensor and sets a DTC.
MONITOR STRATEGY
Related DTCs P0121 Throttle position sensor rationality
Main sensors Throttle position sensor
Required sensors/components
Related sensors Vehicle speed sensor
Frequency of operation Continuous
Duration Within 10 seconds
MIL operation 2 driving cycles
Sequence of operation None

TYPICAL ENABLING CONDITION


Specification
Item
Minimum Maximum
The monitor will run whenever the follow-
See ”List of Disable a Monitor” (On page 05–25)
ing DTCs are not present
Throttle valve position Closed angle position
”Stop and Go” 4 times –
”Stop and go” is defined as follows:
”Stop” indicates a vehicle speed of 0 mph (0 km/h). ”Go” indicates a vehicle speed of 18.6 mph (30 km/h).
TYPICAL MALFUNCTION THRESHOLDS
Detection Criteria Threshold
26.2 or more
Throttle valve at closed angle position
Less than 7.4

COMPONENT OPERATING RANGE


Parameter Standard Value
Throttle valve at closed angle position Between 7.5 and 21
2004 COROLLA (RM1037U)

Author: Date: 259

You might also like