Miele Coffee Maker Cva - 4070 - Enca

Download as pdf or txt
Download as pdf or txt
You are on page 1of 6

Installation Instructions

CVA 4070 en-CA

Installation, repair and maintenance work should be performed by


a Miele authorized service technician in accordance with national
and local safety regulations and the provided installation instructions.

Downloaded from www.Manualslib.com manuals search engine


Electrical connection
Important
Ensure that power is not supplied to
The coffee system comes equipped
the machine while installation or
with a 6 ft (1.8 m) power cord with a
maintenance work is performed.
NEMA 5-15P molded plug for
connection to a 120 V, 15 A, 60 Hz
All electrical work should be
power supply.
performed by a qualified electrician
in strict accordance with national
and local safety regulations.
Installation, repairs and other work
by unqualified persons could be
dangerous.

The manufacturer cannot be held


responsible for unauthorized work.

Verify that the voltage, load and circuit


rating information found on the data
plate match the household electrical
supply before installing the coffee
system.
If there is any question concerning the
electrical connection of this appliance
to your power supply, please consult a
licensed electrician or contact Miele’s
Technical Service Department. See
back page for contact information.

WARNING:
THIS APPLIANCE MUST BE
GROUNDED

57
Downloaded from www.Manualslib.com manuals search engine
Installation

Installation options
The coffee system is designed to be built into cabinetry.

A combination with other Miele built in appliances is possible. If the machine is installed
in combination with other appliances, it should be installed with a protective base
between the appliance and the unit (exception: installation with a built-in plate warmer).

A special display cabinet is also available from your dealer or Miele, as an installation option.

Miele appliances can be installed flush or proud. Discuss your installation


requirements with your architect, designer and installer.

58
Downloaded from www.Manualslib.com manuals search engine
Installation

Installation ^ If your cabinet has 3/4" (19 mm) side


walls, drill four holes for the
Make sure power is not supplied to mounting.
the appliance while installation or
^ Center the unit and turn the screws a
maintenance work is performed.
little bit in and then out again.
Disconnect the power supply to the
work area by unplugging the unit, ^ Take the unit out of the niche and drill
tripping the circuit breaker or four holes at the screw markings
removing the fuse. The coffee (1/16" [2 mm], diameter 3/16"
system must be installed into [4.5 mm]).
cabinetry before being used.
^ Connect the appliance to a cold
water supply.
^ Plug the appliance into the electrical
outlet.
^ Push the appliance into the niche.

^ Unscrew the height adjustable feet


on the underside of the machine
about 1/16" (2 mm).
^ Push the appliance all the way back
into the cabinet and center it. If
necessary level the unit with the four
^ Open the door and partially tighten
height adjustable feet.
the screws.
The feet can be turned out up to 3/8" ^ Carefully turn the lower screws, a, to
(10 mm). center the machine.
^ To secure the appliance in the
cabinet, tighten the upper screws, b,
by hand. Do not use an electric
screwdriver.

59
Downloaded from www.Manualslib.com manuals search engine
Installation

Adjusting the door hinges


The door hinges can be adjusted if the
door cannot be opened easily.

^ To adjust the door sideways, a, turn


screw a.
^ To adjust the door to the front or
back, b, turn screw b.

60
Downloaded from www.Manualslib.com manuals search engine
Alteration rights reserved / 0607 M.-Nr. 06 911 520 / 02
en - USA / CDN
CVA 4070

For the most updated manual see the MIele Website.

Downloaded from www.Manualslib.com manuals search engine

You might also like