TL084

TL084A - TL084B
GENERAL PURPOSE
QUAD J-FET OPERATIONAL AMPLIFIERS

.. LOW POWER CONSUMPTION

WIDE COMMON-MODE (UP TO VCC+) AND

.. DIFFERENTIAL VOLTAGE RANGE

LOW INPUT BIAS AND OFFSET CURRENT

. OUTPUT SHORT-CIRCUIT PROTECTION

HIGH INPUT IMPEDANCE J–FET INPUT

.. STAGE
INTERNAL FREQUENCY COMPENSATION
N
DIP14

. LATCH UP FREE OPERATION

HIGH SLEW RATE : 16V/µs (typ)
(Plastic Package)

D
SO14
(Plastic Micropackage)

DESCRIPTION ORDER CODES

The TL084, TL084A and TL084B are high speed Temperature Package
J–FET input quad operationalamplifiers incorporating Part Number
Range N D
well matched, high voltage J–FET and bipolar transis- o o
TL084M/AM/BM –55 C, +125 C • •
tors in a monolithic integrated circuit. o o
TL084I/AI/BI –40 C, +105 C • •
The devicesfeaturehigh slew rates, low input bias and o o
offset currents, and low offset voltage temperature TL084C/AC/BC 0 C, +70 C • •
coefficient. Examples : TL084CN, TL084CD

PIN CONNECTIONS (top view)

Output 1 1 14 Output 4

Inverting Input 1 2 - - 13 Inverting Input 4

Non-inverting Input 1 3 + + 12 Non-inverting Input 4

VCC + 4 11 VCC -

Non-inverting Input 2 5 + + 10 Non-inverting Input 3

Inverting Input 2 6 - - 9 Inverting Input 3

Output 2 7 8 Output 3

February 1996 1/10

This datasheet has been downloaded from http://www.digchip.com at this page

TL084 - TL084A - TL084B

SCHEMATIC DIAGRAM (each amplifier)

VCC

Non- inver ting

input
I nverting
input
1 0 0Ω
2 0 0Ω
Output

1 0 0Ω
30k

8.2k

1.3k 35k 1.3k 35k 1 0 0Ω

VCC

ABSOLUTE MAXIMUM RATINGS

Symbol Parameter Value Unit
VCC Supply Voltage - (note 1) ±18 V
Vi Input Voltage - (note 3) ±15 V
Vid Differential Input Voltage - (note 2) ±30 V
Ptot Power Dissipation 680 mW
Output Short-circuit Duration - (note 4) Infinite
o
Toper Operating Free Air Temperature Range TL084C,AC,BC 0 to 70 C
TL084I,AI,BI –40 to 105
TL084M,AM,BM –55 to 125
o
Tstg Storage Temperature Range –65 to 150 C
Notes : 1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the
zero reference level is the midpoint between VCC+ and VCC–.
2. Differential voltages are at the non-inverting input terminal with respect to the inverting input terminal.
3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less.
4. The output may be shorted to ground or to either supply. Temperature and /or supply voltages must be limited to ensure that the
dissipation rating is not exceeded.

2/10
 TL084 - TL084A - TL084B

ELECTRICAL CHARACTERISTICS
VCC = ±15V, Tamb = 25oC (unless otherwise specified)
TL084I,M,AC,AI,
TL084C
Symbol Parameter AM,BC,BI,BM Unit
Min. Typ. Max. Min. Typ. Max.
Vio Input Offset Voltage (R S = 50Ω) mV
o
Tamb = 25 C 3 6 3 10
TL084BC,BI,BM 1 3
Tmin. ≤ Tamb ≤ Tmax. 7 13
TL084BC,BI,BM 5
o
DV io Input Offset Voltage Drift 10 10 µV/ C
Iio Input Offset Current *
Tamb = 25oC 5 100 5 100 pA
Tmin. ≤ Tamb ≤ Tmax. 4 4 nA
Iib Input Bias Current *
o
Tamb = 25 C 20 200 30 400 pA
Tmin. ≤ Tamb ≤ Tmax. 20 20 nA
Avd Large Signal Voltage Gain (RL = 2kΩ, VO = ±10V) V/mV
Tamb = 25oC 50 200 25 200
Tmin. ≤ Tamb ≤ Tmax. 25 15
SVR Supply Voltage Rejection Ratio (R S = 50Ω) dB
Tamb = 25oC 80 86 70 86
Tmin. ≤ Tamb ≤ Tmax. 80 70
ICC Supply Current, per Amp, no Load mA
Tamb = 25oC 1.4 2.5 1.4 2.5
Tmin. ≤ Tamb ≤ Tmax. 2.5 2.5
Vicm Input Common Mode Voltage Range ±11 +15 ±11 +15 V
-12 -12
CMR Common Mode Rejection Ratio (RS = 50Ω) dB
o
Tamb = 25 C 80 86 70 86
Tmin. ≤ Tamb ≤ Tmax. 80 70
Ios Output Short-circuit Current mA
Tamb = 25oC 10 40 60 10 40 60
Tmin. ≤ Tamb ≤ Tmax. 10 60 10 60
±VOPP Output Voltage Swing V
Tamb = 25oC RL = 2kΩ 10 12 10 12
RL = 10kΩ 12 13.5 12 13.5
Tmin. ≤ Tamb ≤ Tmax. RL = 2kΩ 10 10
RL = 10kΩ 12 12
SR Slew Rate (Vin = 10V, RL = 2kΩ, CL = 100pF, V/µs
Tamb = 25oC, unity gain) 8 16 8 16
tr Rise Time (Vin = 20mV, RL = 2kΩ, C L = 100pF, µs
o
Tamb = 25 C, unity gain) 0.1 0.1
KOV Overshoot (Vin = 20mV, RL = 2kΩ, C L = 100pF, %
Tamb = 25oC, unity gain) 10 10
GBP Gain Bandwidth Product (f = 100kHz, MHz
o
Tamb = 25 C, Vin = 10mV, R L = 2kΩ, C L = 100pF) 2.5 4 2.5 4
Ri Input Resistance 1012 1012 Ω
THD Total Harmonic Distortion (f = 1kHz, AV = 20dB, %
o
RL = 2kΩ, C L = 100pF, Tamb = 25 C, VO = 2VPP) 0.01 0.01
Equivalent Input Noise Voltage nV
en 15 15
(f = 1kHz, Rs = 100Ω) √
 Hz
∅m Phase Margin 45 45 Degrees
VO1/VO2 Channel Separation (Av = 100) 120 120 dB
* The input bias currents are junction leakage currents which approximately double for every 10oC increase in the junction temperature.

3/10
TL084 - TL084A - TL084B

MAXIMUM PEAK-TO-PEAK OUTPUT MAXIMUM PEAK-TO-PEAK OUTPUT

VOLTAGE VERSUS FREQUENCY VOLTAGE VERSUS FREQUENCY

MAXIMUMPEAK-TO-PEAK OUTPUT
30 30
V CC = 15V R L = 2kΩ R L= 10kΩ
MAXIMUM PEAK-TO-PEAKOUTPUT

25 T a m b = + 25° C 25 Tamb = +25 C

V CC = 15V
S ee Fig ure 2 See Figure 2
20

VOLTAGE (V)
20
VOLTAGE (V)

V CC = 10V VCC = 10V

15 15
10 10
V CC = 5V V CC = 5V
5 5
0 0
100 1K 10K 100K 1M 10M 100 1K 10K 100K 1M 10M
FREQUENCY (Hz) FREQUENCY (Hz)

MAXIMUM PEAK-TO-PEAK OUTPUT MAXIMUM PEAK-TO-PEAK OUTPUT

VOLTAGE VERSUS FREQUENCY VOLTAGE VERSUS FREE AIR TEMP.
MAXIMUMPEAK-TO-PEAK OUTPUT

30
30
MAXIMUM PEAK-TO-PEAKOUTPUT

Ta mb = +25 C VCC = 15V

25
R L = 2kΩ 25
VOLTAGE (V)

20 S ee Figure 2
20
VOLTAGE (V)

R L = 1 0 kΩ
15 15
Ta mb = -55 C R L = 2 kΩ
10 10

5 5 VC C = 15 V
Ta mb = +125 C S e e F i g u re 2
0 0
10k 40k 100k 400k 1M 4M 10M -7 5 -5 0 - 25 0 25 50 75 -50 125

T E MP ER AT U R E ( ° C )
FREQUENCY (Hz)

MAXIMUM PEAK-TO-PEAK OUTPUT MAXIMUM PEAK-TO-PEAK OUTPUT

VOLTAGE VERSUS LOAD RESISTANCE VOLTAGE VERSUS SUPPLY VOLTAGE

30 30
MAXIMUM PEAK-TO-PEAK OUTPUT

MAXIMUM PEAK-TO-PEAKOUTPUT

VCC = 15V RL = 10 kΩ
25 Tamb = +25°C 25
See Figure 2 Tamb = +25°C
20
VOLTAGE (V)

20
VOLTAGE (V)

15 15

10 10
5 5
0
0.1 0.2 0.4 0.7 1 2 4 7 10 0 2 4 6 8 10 12 14 16
LOAD RESISTANCE (k Ω) SUPPLY VOLTAGE ( V)

4/10
 TL084 - TL084A - TL084B

INPUT BIAS CURRENT VERSUS LARGE SIGNAL DIFFERENTIAL

FREE AIR TEMPERATURE VOLTAGE AMPLIFICATION VERSUS
FREE AIR TEMPERATURE

100
1000
V CC = 15V
400
INPUT BIAS CURRENT (nA)

10 200

DIFFERENTIAL VOLTAGE
AMPLIFICATION (V/V)
100

1 40
20
10 V CC = 15V
0.1 VO = 10V
4
2 R = 2k Ω
L

0.01 1
-75 -50 -25 0 25 50 75 100 125
-50 -25 0 25 50 75 100 125
TEMPERATURE (°C)
TEMPERATURE (°C)

LARGE SIGNAL DIFFERENTIAL TOTAL POWER DISSIPATION VERSUS

VOLTAGE AMPLIFICATION AND PHASE FREE AIR TEMPERATURE
SHIFT VERSUS FREQUENCY

250
DIFFERENTIAL VOLTAGE

225 V CC = 15V
TOTAL POWER DISSIPATION (mW)

100
AMPLIFICATION(V/V)

DIFFERENTIAL 180
200 No signal
VOLTAGE
PHASE SHIFT AMPLIFICATION 175 No load
(right s ca le ) (left s ca le)
150
10 90 125
R = 2kΩ 100
L
C L = 100pF 75
1 V CC = 15V 0 50
T amb = +125 C 25
0
100 1K 10K 100K 1M 10M -75 -50 -25 0 50 75 100 125
25
FREQUENCY (Hz)
TEMPERATURE (°C)

SUPPLY CURRENT PER AMPLIFIER SUPPLY CURRENT PER AMPLIFIER

VERSUS FREE AIR TEMPERATURE VERSUS SUPPLY VOLTAGE

2.0 2.0
SUPPLY CURRENT (mA)

1.8 V CC = 15V 1.8 Tamb = +25°C

1.6 No signal 1.6 No signal
SUPPLY CURRENT (mA)

1.4 No load 1.4 No load

1.2 1.2
1.0 1.0
0.8 0.8
0.6 0.6
0.4 0.4
0.2 0.2
0 0
-75 -50 -25 0 25 50 75 100 125 2 4 6 8 10 12 14 16
TEMPERATURE (°C) SUPPLY VOLTAGE ( V)

5/10
TL084 - TL084A - TL084B

COMMON MODE REJECTION RATIO VOLTAGE FOLLOWER LARGE SIGNAL

VERSUS FREE AIR TEMPERATURE PULSE RESPONSE

INPUT AND OUTPUT VOLTAGES

89 6
R L = 1 0 kΩ
COMMON MODE MODE REJECTION

88
VC C =
4 OUTP UT
15V INPUT
87 2
RATIO (dB)

(V)
86 0
VCC = 15V
85 -2 R L = 2 kΩ
84 -4 C L= 100pF
Tam b = +25 C
83 -6
-75 -50 -25 0 25 50 75 100 125 0 0.5 1 1.5 2 2.5 3 3.5
TEMPERATURE (°C) TIME (µs )

OUTPUT VOLTAGE VERSUS EQUIVALENT INPUT NOISE VOLTAGE

ELAPSED TIME VERSUS FREQUENCY

28
70
24 VCC = 15V
OVERSHOOT 60
OUTPUT VOLTAGE (mV)

A V = 10
EQUIVALENT INPUT NOISE

20
R S = 100 Ω
90%
50
VOLTAGE (nV/VHz)

16 T amb = +25°C
40
12
30
8
V = 15V 20
CC
4 R L = 2k Ω
10%
0 10
Tamb = +25°C
t r
-4 0
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 10 40 100 400 1k 4k 10k 40k 100k

TIME ( µs) FREQUENCY (Hz)

TOTAL HARMONIC DISTORTION VERSUS

FREQUENCY

1
V VCC = = 15V
15V
TOTAL HARMONIC DISTORTION

CC
0.4
V V= =
AA 11
VV = 6V
(rms) = 6V
O (rms)
0.1 O
T amb
T amb= =+25°C
+25°C
0.04
(%)

0.01

0.004

0.001
100 400 1k 4k 10k 40k 100k

FREQUENCY (Hz)

6/10
 TL084 - TL084A - TL084B

PARAMETER MEASUREMENT INFORMATION

Figure 1 : Voltage Follower Figure 2 : Gain-of-10 Inverting Amplifier

10k Ω

- 1k Ω
eI -
1/4
TL084 eo 1/4
TL084 eo

eI
CL = 100pF RL = 2kΩ
RL CL = 100pF

TYPICAL APPLICATIONS
AUDIO DISTRIBUTION AMPLIFIER

f O = 100kH z

1/4
Output A
1M Ω TL0 84

1/4 -
1 µF TL0 84
1/4
Input TL084
Output B

100k Ω 100kΩ
100k Ω
V CC+
1OO µF -
100k Ω
1/4
Output C
TL0 84

7/10
TL084 - TL084A - TL084B

TYPICAL APPLICATIONS (continued)

POSITIVE FEEDBACK BANDPASS FILTER

16 k Ω 16 k Ω

22 0p F 220pF

43k Ω 43 k Ω

43 k Ω 30 k Ω 43 k Ω 30 k Ω
Input - -

22 0pF 1/4 1/4 43 k Ω

- 22 0p F -
TL08 4 TL 08 4
43 k Ω 1/4 1/4
TL08 4 TL 084
Output B
1 .5 k Ω 1 .5 k Ω

Ground
Output A

OUTPUT A OUTPUT B

SECOND ORDER BANDPASS F ILT ER CASCADED BANDPASS F IL TER

fo = 100kHz ; Q = 30 ; Gain = 4 fo = 100kHz ; Q = 69 ; Gain = 16

8/10
 TL084 - TL084A - TL084B

PACKAGE MECHANICAL DATA

14 PINS - PLASTIC DIP OR CERDIP

Millimeters Inches
Dimensions
Min. Typ. Max. Min. Typ. Max.
a1 0.51 0.020
B 1.39 1.65 0.055 0.065
b 0.5 0.020
b1 0.25 0.010
D 20 0.787
E 8.5 0.335
e 2.54 0.100
e3 15.24 0.600
F 7.1 0.280
i 5.1 0.201
L 3.3 0.130
Z 1.27 2.54 0.050 0.100

9/10
TL084 - TL084A - TL084B

PACKAGE MECHANICAL DATA

14 PINS - PLASTIC MICROPACKAGE (SO)

Millimeters Inches
Dimensions
Min. Typ. Max. Min. Typ. Max.
A 1.75 0.069
a1 0.1 0.2 0.004 0.008
a2 1.6 0.063
b 0.35 0.46 0.014 0.018
b1 0.19 0.25 0.007 0.010
C 0.5 0.020
o
c1 45 (typ.)
D 8.55 8.75 0.336 0.334
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 7.62 0.300
F 3.8 4.0 0.150 0.157
G 4.6 5.3 0.181 0.208
L 0.5 1.27 0.020 0.050
M 0.68 0.027
o
S 8 (max.)

Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsi-
bility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which
may result from its use. No licence is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON
Microelectronics. Specifications mentioned in this publ ication are subject to change without notice. This pub lication supersedes
and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical
components in life support devices or systems without express written approval of SGS-THOMSON Microelectronics.

 1996 SGS-THOMSON Microelectronics - All Rights Reserved

SGS-THOMSON Microelectronics GROUP OF COMPANIES

Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands
Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A.

10/10