Ordering Information Parameter Setting Method

Front Panel View

Three-phase Voltage Monitoring Relay
Press and hold key for 3 seconds to get into parameter setting interface,then
JVR800-2 Model Rated Voltage Operating Range
press to shit to next parameter,press to set up the values. Long press
RUN FAULT COUNT TIME
JVR800-2 208~480VAC,50/60Hz 150~600VAC Reset/Test could accelerate increase or decrease.Press to exit setting.
Features A S
B SET Digit +/line voltage shift LCD indication Parameters Setting range Default
Compact modular 43mm housing C V
Microprocessor technology provides highly U> U< ASYM SEQ LOSS Digit -/line voltage shift
accurate and repeatable protection Technical data V
overvoltage threshold 200-600V,OFF *1 437V
Built-in LCD and keypad afford a precise Parameters setting
>

digital setting Rated supply voltage 208-480VAC /timing and counting query S
overvoltage delay time 0.1-999s 5s
Adjustable over- and undervoltage phase
Operating Range 150-600VAC >
unbalance threshold
LCD Indication Description
Independent adjustable delay time for Operating frequency 50/60Hz
undervoltage threshold OFF,150-500V 323V
overvoltage, undervoltage, voltage timing and counting value V
Max counting capacity 999999 <
unbalance,phase loss and phase sequence
Max timing capacity 9999H59M line voltage
Adjustable reset method:automatic reset or V
S undervoltage delay time 0.1-999s 5s
manual reset Max counting frequency 5Hz A B C phase indication,shift by <
1 NO & 1CO contacts Total timing error 0.001%
SET parameters setting indication
Fault recording with last 3 faults voltage hysteresis 1-20V 5V
Counting input signal AC/DC 80-450V V
with Timer and Counter RUN COUNT The counting times of running,shift by > <
Measurement error 1% with ajustable volatage range
RUN TIME The time of running,shift by
Data retention time 10 years voltage unbalance ratio 1%-50%,OFF *2 15%
Protective Functions Applications Output type 1NO & 1CO FAULT COUNT The number of faults,shift by

Pumps Contact capacity 6A,250VAC/30VDC (resistive load) FAULT TIME The time of faults,shift by S voltage unbalance 0.1-999s 5s
Phase Loss(Failure) delay time
Fans Degree of protection IP 20 Overvoltage fault indication
U>
Pase Sequence (Reversal) or overvoltage setting indication
Refrigeration Units Working conditions -25 ~65 , 85%RH,non-condensing
Undervoltage fault indication voltage unbalance
Voltage Unbalance (Asymmetry) Blowers U< hysteresis
1%-10% 2%
Mechanical durability 1000000 cycles or Undervoltage setting indication
Undervoltage Motors Voltage unbalance( Asymmetry) fault indication
Dielectric strength >2kVAC 1min ASYM or phase unbalance setting indication
Compressors S phase loss delay time 0.1-30.0s,OFF 0.5s
Overvoltage Weight 130g Phase sequence fault indication
Lifts,Elevators SEQ or phase sequence setting indication LOSS
Dimensions (H x W x D) 80X43X54mm
Cranes Phase loss fault indication Following next page...
Mounting 35mm DIN rail
LOSS
Mining excavators and conveyors or phase loss setting indication

-1- -2- -3- -4-

Parameter Setting Method Start Delay /Power-on Delay Fault History Check
(Continued) If start delay time is set,start delay will be active when power is turned on ,the display Pressing more than 3sec, it displays the latest fault cause and the fault voltage. Note:specifications are subject to change without notice.
shows "Start" and countdown.The display will get into the voltage display when Press to check later fault continually.Press or to shift the display of other
LCD indication Parameters Setting range Default
countdown expires. two line voltage.Press after Log3 to exit or press directly to exit. The oldest
fault record is over written when the number of fault to record exceeds three.
GENERAL SAFETY
S phase sequence RUN COUNT POTENTIALLY HAZARDOUS VOLTAGES ARE PRESENT AT THE
0.1-30.0s,OFF 0.5s
SEQ
delay time S S ..... S A
RUN COUNT TERMINALS OF THE RELAYS.
B
V ALL ELECTRICAL POWER SHOULD BE REMOVED WHEN
A A A
B
V
B
V
B
V
B
V CONNECTING OR DISCONNECTING WIRING.
S start delay time 0-999s *3 0s
Test Trip
U>
C
U< SEQ THIS DEVICE SHOULD BE INSTALLED AND SERVICED BY
the latest fault the second fault the oldest fault QUALIFIED PERSONNEL.
Pressing more than 3sec to active the test trip mode, all the output contacts will
auto reset mode ON/OFF ON trip when 3s expires.The display shows "test" and countdown,when the test is done,the
display shows "End".By pressing , returns to the voltage display mode.Before 3s Wiring Diagram
expires, pressing blocks the test trip and return to the voltage display.
S auto reset time 0.1-999s 5s

S S S
KM
restore factory default YES/NO NO FUSE

AC/DC 80-450V
Dimensions(mm)
clear records NO/YES/OFF *4 NO

L1 L2 L3 C1 C2

voltage frequency 50/60Hz 50Hz

JVR800-2

item version ver 3.0 ----

14 11 12 21 22
35

80

exit ---- ----

Note: If you have any questions, please

1. "ON" means enable the function,"OFF" means disable the function.
Relay contact position shown in 'Power on' (Healthy) condition
contact us...
2.Voltage unbalance factor (%) = ( U line voltage - U line average max / U line average) x 100%.
3.Start delay time is equivalent to power-on delay time. [email protected]
4.Timer and counter records for running and faults will be clear all if this function is YES.
5.The relay would automatically exit setting interface if any key is not pressed for
54 43
+1 800-585-1519
consecutive 30 seconds.
-5- -6- -7- www.ato.com