Spiral Welded Steel Pipe Dimension

SPIRAL WELDED STEEL PIPE
DIMENSION
We manufacture spiral welded steel pipes with diameters ranging between 350 mm –
3,600 mm and thicknesses between 6 mm – 18 mm. We can produce pipes in any
length as long as the pipe can transported from our manufacturing plant to client site.
ADVANTAGE OF SPIRAL PIPE
Spiral pipe offers more accuracy in roundness of the pipe compared to other means of
production because of the nature of its continuous rolling and welding. The welding
seam is also uniformly distributed throughout the length of the pipe. Good concentricity
makes the pipe casing easy to weld together which prevents problem during installation
at site. The spiral has a continuous spiral seam along its length.
Spiral pipe is welded both internally and externally which significantly increases its
strength.
Our pipes undergo quality control tests such as material control tests, hydrostatic
pressure tests, holiday test, or X-RAY tests if needed. Aside from these standard tests,
we can also facilitate destructive testing by a third part inspector upon request.
We can also cater coating protection such as polyurethane, epoxy, coal tar pain, and
primer base on client’s design.
We can deliver to any point in the Philippines accessible by ship or truck.
The spacious plant site provides for extensive manufacturing and storage of finished
product, resulting to minimal damages during storage. Our production capacity is 80MT
per day.
ROLLED AND WELDED STEEL PIPE

Our rolled and welded steel pipe is available from 400mm up to 3000mm diameter with
a thickness ranging from 6mm to 25mm. The pipes can be weld together to produce any
lengths if the size is possible to be transported from our plant to site.
Rolled pipe is produced by bending a steel plate using a bending roller. The rollers are
adjusted based on the diameter of the pipe that is needed to be produced. After the
plate has formed into a circular shape, the edge of the plate should be welded together
on the outside and inside. The main difference of LSAW to SSAW is the welding seam.
The seam on the SSAW is just a straight line along its length. A number of individual
pipes is welded together to produce a long-rolled pipe casing.
Rolled pipe has a higher load capacity than spiral pipe because it has less welding.
Since it has fewer seams, residual stress is also lesser compare to spiral pipes. Heat
affected zones are considered weak points where failure might start.
Rolled pipes is much difficult to produce than spiral pipe. It also takes longer time to
produce rolled pipe than spiral because the welding part is done manually.
The material we used for pipe casing are ASTM A252 Grade 2, A36, S355, but we can
use other steel grade if required.
We also fabricate different kind of pipe fittings such as 90 degree elbow, 45 degree
elbow, concentric and eccentric reducer, trifurcation, T-joints, Y-joints, and others.
STEEL SHEET PILE

We stock a thousand pieces of type 2 sheet pile at Manila port and replenish it
periodically. We have partnered with the largest producer of sheet pile in China and with
one of the biggest sheet pile distributors here in the Philippines.
Type 2 sheet pile is the most common type of sheet pile we used in the Philippines. It
has a width of 400mm and a height of 100mm. Its thickness is 10.5mm on the flange
and on the web.
We do sheet pile retention simulation and design using GEO5 software. We help our
customers in choosing the suitable length for their various soil retention requirement.
We also cater sheet pile driving and general foundation works.
ANCHOR TIE ROD

Our fabrication plant in Quezon City and Malabon produces anchor tie rods of various
diameter and lengths. Normally a single rod is set to 6 meters only and is linked to other
rod using either coupler, turnbuckle, or hinge joint. We use steel grade of SAE1045,
AISI1040, SCM440, and others. We have supplier anchor tie rod from Ilocos to Jolo,
Sulu.
FLANGE
We fabricate various type of steel pipe flange suitable for pipe from 250mm up to
1000mm. We can produce pipe flange based on ISO, ANSI, or AWWA standards.
Our flange is complete with bolts, nuts, and flange gasket. We also produce dismantling
joint for pipelines. Most of our customers are contractors of major water concessionaires
in Metro Manila – Maynilad and Manila Water.

Spiral Welded Steel Pipe Dimension

Uploaded by

Copyright:

Available Formats

Spiral Welded Steel Pipe Dimension

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Spiral Welded Steel Pipe Dimension

Uploaded by

Copyright:

Available Formats

SPIRAL WELDED STEEL PIPE

ROLLED AND WELDED STEEL PIPE

STEEL SHEET PILE

ANCHOR TIE ROD

You might also like