Back Door Cannot Open
Back Door Cannot Open
Back Door Cannot Open
CIRCUIT DESCRIPTION
Manual unlock signals and key–linked unlock signals (from the driver or passenger side door) are sent to
the door control relay which then unlocks all the doors simultaneously. Pressing the opener switch (outside
handle switch) when the back door is unlocked will release the latch and move it to the open position. This
enables the back door to open.
WIRING DIAGRAM
D4
F8 I10 J4
Instrument Panel J/B Assy Instrument Panel J/B Assy Door Control Relay Assy
FL Block Assy Ignition Switch Assy J/C
1 8 4 GAUGE 3
ALT 4 B–G AM1 W–L 1 AM1 2 B–Y R–B B B R–B 26
1C 1O 1O 1L IG
1 2 IG1
10
D/L L–W 1
1L B
D11
8
Power Window Regulator Master Unlock 8 G–B G–B
IC2
Switch Assy (Door Control Switch) J/C E
W–B 1
J10 C J2
J/C 9 B B
W–B 3 5 BR–Y BR–Y BR–Y 18
Lock IC2 J3 J2 L1
C C
C
D12
Door Control Switch (Passenger Side) 8 E E
Unlock 5 G–B G–B G–B 19
W–B IG2 J3 J2 UL1
B
W–B 3
J2
9
6 BR–Y BR–Y
IG2
Lock
W–B W–B 12
E
D9
Front Door Lock Actuator Assy LH
Unlock
7 Detection 5
W–B W–B 3 4 L–R L–R 6
IC1 IC2 LSWD
11
Unlock 6 Y–B Y–B 21
IC2 UL3
10
5 L–W L–W
IC2
Lock
D10
Front Door Lock Actuator Assy RH 11
Unlock 1 L–R L–R L–R 22
8 IG2 UL2
W–B W–B W–B 4 B
IG1 10
2 L–W L–W B B L–W 20
IG2 L2
Lock J8
J/C
D5 Instrument Panel J/B Assy
Front Door Courtesy Lamp Switch Assy (Driver Side) 1 8
1 R R 5
1S 1L DCTY
B5
Back Door Lock Assy
4 3 4
W–B 1 2 R–W R–W R–W 7
BC1 1S 1L PCTY
3 13
W–B 4 3 L–Y L–Y L–Y 10
BC1 IB2 BACT
B6
Back Door Opener Switch 1 5
Battery W–B 1 2 BR–Y BR–Y BR–Y 17
BC2 IB2 BDSU
W–B
IE BL
B70620
INSPECTION PROCEDURE
1 INSPECT BACK DOOR LOCK ASSY (DOOR LOCK MOTOR
Position
Full–latch
Open–latch
OK
Position
Full–latch
Open–latch
OK
3 CHECK WIRE HARNESS (BACK DOOR LOCK ASSY – DOOR CONTROL RELAY
ASSY AND BODY GROUND)
Wire Harness Side (a) Disconnect the B5 lock and D4 relay connectors.
(b) Check the resistance of the wire harness side connectors.
B5 Standard:
Back Door Lock Assy
Tester Connection Specified Condition
B5–3 – D4–10 (BACT)
B5–12 – D4–7 (PCTY)
Below 1 Ω
B5–1 – Body ground
B5–4 – Body ground
D4 BACT
Door Control Relay Assy
B57790
PCTY NG REPAIR OR REPLACE HARNESS AND
B71976 CONNECTOR
OK
OK
Wire Harness Side (a) Disconnect the B6 switch and D4 relay connectors.
(b) Check the resistance of the wire harness side connectors.
B6 Standard:
Back Door Opener Switch Tester Connection Specified Condition
(Outside Handle Switch)
B6–2 – D4–17 (BDSU)
Below 1 Ω
B6–1 – Body ground
B71961
D4
Door Control Relay Assy
OK