Scribd Logo
Upload

Welcome to Scribd!

  • 98 views

    Brake Fluid: Bleeding

    Uploaded by

    DannyDDannyD
    1. Bleed the air out of the brake system by filling the reservoir with brake fluid, disconnecting the brake lines from the master cylinder, and pumping and holding the brake pedal to push fluid through. 2. Bleed each brake line by connecting a tube to the bleeder plug, loosening the plug while pumping the brake pedal, and tightening it once fluid runs clear. 3. Use a hand-held tester to bleed the brake actuator by selecting the air bleeding function and following the displayed steps to bleed the increase, inhalation, and decrease lines.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Brake Fluid: Bleeding

    Uploaded by

    DannyDDannyD
    98 views4 pages
    1. Bleed the air out of the brake system by filling the reservoir with brake fluid, disconnecting the brake lines from the master cylinder, and pumping and holding the brake pedal to push fluid through. 2. Bleed each brake line by connecting a tube to the bleeder plug, loosening the plug while pumping the brake pedal, and tightening it once fluid runs clear. 3. Use a hand-held tester to bleed the brake actuator by selecting the air bleeding function and following the displayed steps to bleed the increase, inhalation, and decrease lines.

    Original Title

    Bleeding

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1. Bleed the air out of the brake system by filling the reservoir with brake fluid, disconnecting the brake lines from the master cylinder, and pumping and holding the brake pedal to push fluid through. 2. Bleed each brake line by connecting a tube to the bleeder plug, loosening the plug while pumping the brake pedal, and tightening it once fluid runs clear. 3. Use a hand-held tester to bleed the brake actuator by selecting the air bleeding function and following the displayed steps to bleed the increase, inhalation, and decrease lines.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    98 views4 pages

    Brake Fluid: Bleeding

    Uploaded by

    DannyDDannyD
    1. Bleed the air out of the brake system by filling the reservoir with brake fluid, disconnecting the brake lines from the master cylinder, and pumping and holding the brake pedal to push fluid through. 2. Bleed each brake line by connecting a tube to the bleeder plug, loosening the plug while pumping the brake pedal, and tightening it once fluid runs clear. 3. Use a hand-held tester to bleed the brake actuator by selecting the air bleeding function and following the displayed steps to bleed the increase, inhalation, and decrease lines.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    32–4

    BRAKE – BRAKE FLUID

    BRAKE FLUID
    320YH–01

    BLEEDING
    HINT:
    If any work is performed on the brake system or if air in the brake lines is suspected, bleed the air out of the
    brake system.
    NOTICE:
    Wash the brake fluid off immediately if it adheres to any painted surfaces.

    1. FILL RESERVOIR WITH BRAKE FLUID


    Fluid: SAE J1703 or FMVSS No. 116 DOT3

    F45659

    2. BLEED MASTER CYLINDER


    HINT:
    If the master cylinder has been disassembled or if the reservoir
    becomes empty, bleed the air out of the master cylinder.
    (a) Disconnect the brake lines from the master cylinder.
    SST 09023–00100
    (b) Slowly depress and hold the brake pedal.

    F45660

    (c) Cover off the outer holes with your fingers, and release
    the brake pedal.
    (d) Using SST, Repeat (b) and (c) 3 or 4 times.
    (e) Connect the brake lines from the master cylinder.
    SST 09023–00100
    Torque: 15 N⋅m (155 kgf⋅cm, 11 ft⋅lbf)

    F46062

    3. BLEED BRAKE LINE


    (a) Connect the vinyl tube to either one of the bleeder plug.
    (b) Depress the brake pedal several times, then loosen the
    bleeder plug with the pedal depressed.
    (c) When fluid stops coming out, tighten the bleeder plug,
    then release the brake pedal.
    Torque: 8.3 N⋅m (85 kgf⋅cm, 73 in.⋅lbf)
    (d) Repeat (b) and (c) until all the air in the fluid is completely
    F45651 bled out.

    2004 SCION xB REPAIR MANUAL (RM1031U)

    Author: Date: 1200


    32–5
    BRAKE – BRAKE FLUID

    (e) Repeat the above procedure to bleed the air out of the
    brake line for each wheel.
    4. BLEED BRAKE ACTUATOR
    NOTICE:
    After performing the usual air bleeding in the brake system,
    if the height or feel of the brake pedal cannot be obtained,
    perform air bleeding in the VSC actuator assy with the
    hand–held tester by following the procedures below.
    (a) Depress the brake pedal more than 20 times with the en-
    gine off.
    (b) Connect the hand–held tester to the DLC3, then turn the
    Hand–held Tester
    ignition switch ON.
    NOTICE:
    Do not start the engine.
    (c) Select ”AIR BLEEDING” on the hand–held tester.
    HINT:
    Please refer to the Hand–Held Tester Operator’s Manual for fur-
    ther details.
    DLC3
    F45399 (d) Bleed out the air out of the reqlal brake line in ”Step1: In-
    crease” on the hand–held tester display.
    NOTICE:
     Perform the air bleeding by following the steps dis-
    played on the hand–held tester.
     Make sure that the brake fluid in the master cylinder
    reservoir tank does not become empty.
    (1) Connect the vinyl tube to either one of the bleeder
    plugs.

    (2)Depress the brake pedal several times, then loosen


    the bleeder plug of one of the above wheels with the
    pedal depressed.
    (3) When fluid stops coming out, tighten the bleeder
    plug, then release the brake pedal.
    Torque: 8.3 N⋅m (85 kgf⋅cm, 73 in.⋅lbf)
    (4) Repeat (2) and (3) until all the air in the fluid is com-
    pletely bled out.
    F45651 (5) Repeat the above procedure to bleed the air out of
    the brake line for each wheel.
    (e) Bleed the air out of the suction line in ”Step2: Inhalation”
    on the hand–held tester display.
    NOTICE:
     Perform the air bleeding by following the steps dis-
    playedon the hand–held tester.
     Be careful that the brake fluid in the master cylinder
    reservoir tank does not become empty.
    (1) Connect the vinyl tube to the bleeder plug at the
    right front wheel or the right rear wheel and loosen
    the bleeder plug.
    2004 SCION xB REPAIR MANUAL (RM1031U)

    Author: Date: 1201


    32–6
    BRAKE – BRAKE FLUID

    (2) Operate the ABS actuator assy using the hand–


    held tester to bleed the air.
    NOTICE:
     The operation stops automatically in 4 seconds.
     At this time, be sure to release the brake pedal.
    (3) Check that the operation stops by using the screen
    of the hand–held tester.
    (4) Repeat (2) and (3) until all the air in the fluid is com-
    pletely bled out.
    Torque: 8.3 N⋅m (85 kgf⋅cm, 73 in.⋅lbf)
    (5) For the rest of the wheels, bleed the air in the same
    way as stated in the above procedure.
    (f) Bleed the air out of the pressure reduction line in ”Step3:
    Decrease” on the hand–held tester display.
    NOTICE:
     Perform the air bleeding by following the stepsdis-
    played on the hand–held tester.
     Make sure that the brake fluid in the master cylinder
    reservoir tank does not become empty.
    (1) Connect a vinyl tube to either one of the bleeder
    plugs.
    (2) Loosen the bleeder plug.
    (3) Using the hand–held tester operate the ABS actua-
    tor assy using hand–held tester, completely de-
    press the brake pedal and keep depressing it.
    NOTICE:
     The operation stops automatically in 4 seconds.
    When performing this procedure continuously, an in-
    terval of at least 20 seconds is required.
     When the operation is completed, the brake pedal
    slightly goes down. This is a nomal phenomenon
    caused when the solenoid opens.
     During this procedure, the pedal seems heavy, but
    completely depress it so that the brake fluid comes
    out from the bleeder plug.
     Be sure to keep depressing the brake pedal. Never
    depress and release the pedal repeatedly.
    (4) Tighten the bleeder plug, then release the brake
    pedal.
    Torque: 8.3 N⋅m (85 kgf⋅cm, 73 in.⋅lbf)
    (5) Repeat (2) to (4) until all the air in the fluid is com-
    pletely bled out.
    (6) Repeat the above procedure to bleed the air out of
    the brake line for each wheel.

    2004 SCION xB REPAIR MANUAL (RM1031U)

    Author: Date: 1202


    32–7
    BRAKE – BRAKE FLUID

    (g) Bleed the air out of the requiar brake line again in ”Step4:
    Increase” on the hand–held tester display.
    NOTICE:
     Perform air bleeding by following the stepsdisplayed
    on the hand–held tester.
     Make sure that the brake fluid in the master cylinder
    reservoir tank does not become empty.
    (1) Connect the vinyl tube to either one of the bleeder
    plugs.

    (2) Depress the brake pedal several times, then loosen


    the bleeder plug of one of the above wheels with the
    pedal depressed.
    (3) When fluid stops coming out, tighten the bleeder
    plug, then release the brake pedal.
    Torque: 8.3 N⋅m (85 kgf⋅cm, 73 in.⋅lbf)
    (4) Repeat (2) and (3) until all the air in the fluid is com-
    pletely bled out.
    C80826 (5) Repeat the above procedure to bleed the air out of
    the brake line for each wheel.
    5. CHECK FLUID LEVEL IN RESERVOIR
    (a) Check the fluid level and add fluid, if necessary.
    Fluid: SAE J1703 or FMVSS No. 116 DOT3

    F45659

    2004 SCION xB REPAIR MANUAL (RM1031U)

    Author: Date: 1203

    You might also like