Scribd
Upload
148 views3 pages

Assignment 2

This document contains an assignment on heat transfer with 8 questions. It asks about the differences between laminar and turbulent flow and which has a higher heat transfer coefficient. It also asks about the physical significance of the Reynolds number and how it is defined for external flow over a plate. Several questions involve calculating heat transfer rates and temperatures given conditions like flow velocities, temperatures, pipe dimensions, and heat transfer coefficients. The last question asks to determine the overall heat transfer coefficient and compare thermal resistances for a stainless steel tube in a heat exchanger.

Uploaded by

Fasil
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
148 views3 pages

Assignment 2

This document contains an assignment on heat transfer with 8 questions. It asks about the differences between laminar and turbulent flow and which has a higher heat transfer coefficient. It also asks about the physical significance of the Reynolds number and how it is defined for external flow over a plate. Several questions involve calculating heat transfer rates and temperatures given conditions like flow velocities, temperatures, pipe dimensions, and heat transfer coefficients. The last question asks to determine the overall heat transfer coefficient and compare thermal resistances for a stainless steel tube in a heat exchanger.

Uploaded by

Fasil
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Submission Deadline: __________________________

ADDIS ABABA UNIVERSITY


AAiT
School of Mechanical and Industrial Engineering
Heat Transfer (MEng 3171): Assignment II Instructor: Dawit M.

1. How does turbulent flow differ from laminar flow? For which flow is the heat transfer coefficient
higher?

2. What is the physical significance of the Reynolds number? How is it defined for external
flow over a plate of length L?

3. The local atmospheric pressure in Denver, Colorado (elevation 1610 m), is 83.4 kPa. Air at this
pressure and 20°C flows with a velocity of 8 m/s over a 1.5 m x 6 m flat plate whose temperature
is 140°C. Determine the rate of heat transfer from the plate if the air flows parallel to the (a) 6-m-
long side and (b) the 1.5-m side.

4. The components of an electronic system are located in a 1.5m-long horizontal duct whose cross
section is 20 cm X 20 cm. The components in the duct are not allowed to come into direct
contact with cooling air, and thus are cooled by air at 30°C flowing over the duct with a velocity
of 200 m/min. If the surface temperature of the duct is not to exceed 65°C, determine the total
power rating of the electronic devices that can be mounted into the duct.

Page 1 of 3
5. Water is to be heated from 15°C to 65°C as it flows through a 3-cm-internal-diameter 5-m-long
tube. The tube is equipped with an electric resistance heater that provides uniform heating
throughout the surface of the tube. The outer surface of the heater is well insulated, so that in
steady operation all the heat generated in the heater is transferred to the water in the tube. If the
system is to provide hot water at a rate of 10 L/min, determine the power rating of the resistance
heater. Also, estimate the inner surface temperature of the pipe at the exit.

6. Hot air at atmospheric pressure and 80°C enters an 8–m-long uninsulated square duct of cross
section 0.2 m x 0.2 m that passes through the attic of a house at a rate of 0.15 m3/s. The duct
is observed to be nearly isothermal at 60°C. Determine the exit temperature of the air and the
rate of heat loss from the duct to the attic space.

7. A type-302 stainless steel tube of inner and outer diameters Di = 22 mm and Do = 27 mm,
respectively, is used in a cross-flow heat exchanger. The fouling factors, Rƒ, for the inner and
outer surfaces are estimated to be 0.0004 and 0.0002 m2 K/W, respectively.

Page 2 of 3
Determine the overall heat transfer coefficient based on the outside area of the tube, Uo. Compare the thermal
resistances due to convection, tube wall conduction, and fouling.

8. Steam in the condenser of a power plant is to be condensed at a temperature of 30°C with cooling water
from a nearby lake, which enters the tubes of the condenser at 14°C and leaves at 22°C. The surface area of
the tubes is 45 m2, and the overall heat transfer coefficient is 2100 W/m2· °C. Determine the mass flow rate
of the cooling water needed and the rate of condensation of the steam in the condenser.

Page 3 of 3

You might also like