FREE PLANS: HOW TO BUILD THE

Caravela 1.7

B & G Yacht Design

[email protected]

www.yachtdesign.com.au
 How to Build the Dinghy Caravela 1.7
To build a Caravela 1.7 is similar to assembling a jigsaw puzzle where the
pieces are numbered in a linear sequence. All it’s required is to follow the instructions
contained in this building manual and for that matter there is no risk of making a
mistake during the construction, since guesswork is eliminated.

1 – The building components

1 – 1 – Bottom panels – (marine plywood – 4 mm)

1 – 2 – Bilge panels – (marine plywood - 4mm)

1 – 2 – Topside panels – (marine plywood - 4mm)

1 – 3 – 1 – Leeboard trunk panels (marine plywood – 4mm)

1 – 4 – Fore transom – (marine plywood – 4mm)

1 – 5 – Foc’sl bulkhead (marine plywood - 4mm)

1 – 6 – Midsection bulkhead (marine plywood - 4mm )

1 – 7 - Stern transom (marine plywood - 4mm)

1 – 8 – Longitudinal bulkheads (marine plywood - 4mm)

1 – 9 – Keelson (lumber 18mm)

1 – 10 – Deck (marine plywood - 4mm)

1 – 11 – Cockpit floorboard (marine plywood - 4mm)

2 - Making the various components at

the work bench
2 – 1 – Using the quotations contained in the plans, the builder will be able to draw
correctly all full size panels. To draw the curved lines use a flexible batten (spline)
passing by the dots that control the curves.
2 – 2 – Once drawn, cut the plywood following the lines. Plane or sand the cut edges to
produce a clean finishing.
2 – 3 – Where there are notches, sand its three sides, using for that purpose a sandpaper
backed by a 4mm plywood straight edge bonded to the sandpaper.

3 – How to assemble the hull

3 – 1 – Draw a 6 mm internal parallel line to each edge of the panels. Make a 1,5mm
hole at each corner of these lines. In one of the panels that is going to be joined to
another, make a hole 15mm apart from the first one and from then on, make holes at
each 30mm along the line. On the other panel, after drilling the hole made at the corner,
continue making holes at each 30 mm along the line.
3 – 2 – With a nylon thread and a thick needle, sew the bottom panels to the
intermediate ones, and these to the side panels and transom.
3 – 3 – Once the hull is stitched, turn the dinghy upside, make an epoxy putty adding
micro sphere as a filler until this becomes the consistency of mayonnaise. You can add
aerosil up to the proportion of 20% of the micro sphere, to increase the filler viscosity.
Apply this putty to the internal edges of the chines with a round edge spatula with 25
mm radius. The putty should cover stitches and the holes that were made. You can use a
commercial epoxy putty ready to be used instead of making it yourself. West Systems
and other suppliers produce excellent products for these purposes
3 – 4 – Once the putty is cured, turn the dinghy upside down and apply a 80mm wide
200g/m2 fibreglass tape on each chine of the dinghy. Saturate the glass cloth with epoxy
resin. Following, apply one layer of 100g/m2 glass cloth over the entire hull. After
curing, sand thoroughly this encapsulation. At this stage the dinghy is already solid
enough to be handled with safety.

4 –Building the internal structure

4 – 1 – The first pieces to be installed are the foc’sle bulkhead and the midsection
bulkhead. Mark with a pencil in the internal side of the hull the exact position of these
two bulkheads.
4 – 2 –Adjust them carefully so they fit into their correct positions. Round the corners
that touch the edges, with a radius a bit larger than the filleted chines, so that bulkhead
edges touch the hull continuously. Once these bulkheads are attached, fillet them
against the hull in the same way as was explained for the internal chines. Fillet up to the
slot where the sheer clamp will be fitted, leaving this slot open.
4 – 3 – Bond the 18 mm x 18 mm supporting cleats shown in sheets 9 and 10. Bond the
equivalent supports on the transom. To help fix these supports until the glue hardens,
you can use 16mm (5/8”) s. s. self tapping flat head screws, screwed from the plywood
to the wood. You can also use clamps to press the two parts until the glue is cured. The
excess glue can be removed with a spatula and the stained surface cleaned with a rag
wet in alcohol.
4 – 4 – Install the keelson in its place gluing it to focs’le bulkhead, bottom panel and
stern transom. The keelson should fit into the mid section bulkhead by means of two
half notches, one in each component. Fillet the keelson at both sides to the bottom
panel.

5 – Building and installing the lee cases

Before fixing the deck in place, the leeboard cases must be installed

5.1 – Draw two vertical lines on each topside, one of them in a station 607mm ahead of
the aft transom, and the other one 186 mm forwards.
5.2 – Build two boxes open in its upper and lower sides, using rectangular 4 mm
plywood panels for their sides and 18 mm x 18 mm cleats to close them.
5.3 – Laminate a layer of 100g/m2 glass cloth at the inner faces of these panels.
5.4 – Once the laminations are cured, sand their surfaces and apply the same coats of
paint that will be applied on the whole hull. Cover with masking tape two 18 mm wide
belts at each extremity of the panels where the 18 mm x 18 mm cleats will be glued to
join the boxes two side walls.
5.5 – Assemble the boxes screwing and gluing the two pairs of panels to the 18 mm x
18 mm cleats.
5.6 – Turn the dinghy sideways leaving one topside facing up. Apply an epoxy putty
(can be again a homemade putty, adding microsphere or wood fine grain saw-dust,
preferably collected from a sander dust bag, to the epoxy resin, orcan be a commercial
product ready to be used). Apply this putty on the area where the case will be placed,
and on the contact face of the case with the topside. It’s advisable to protect with
masking tape the outside border of the attaching place.
5.7 – Place the first case precisely in its position, which is easily recognised by the
masking tapes placed outside the border lines. Hold the case in place, employing a pair
of large quick action clamps to allow them to reach about half the height of the cases.
Insert a 17 mm thick cleat inside the slot, so the clamp that will hold the case in place
doesn’t bend the outside wall when the pressure is applied. Fix the first clamp in the
area where the dinghy’s beam is the largest. Fix the other clamp at the fore extremity.
Considering epoxy doesn’t require excessive pressure to hold the glued parts in place,
apply pressure gently to join the case to the topside, keeping the case outside parallel to
the dinghy’s centreline, taking care that the putty in excess is spilled all over the edges.
Remove with a spatula this excess, and remove the masking tape before the putty sets.
When the putty is cured, remove the clamps and the cleat placed to resist the
compression of the clamp and turn the dinghy to the other side to attach the other case.
5.8 – Fillet the intersection of topsides with cases, with the radius indicated in cross
section AA”drawing. Round the external edges and encapsulate with 100g/m2 glass
cloth both cases surpassing the cloth about 50 mm fore and aft beyond the fillets. Sand
this lamination and the hull is ready for painting.
 6 – Fitting the keel and the two lateral
supports
6 1 – The keel is built in two cold moulded 18 mm x 9 mm layers. The first one is
screwed and glued over the bottom centre line with the dinghy upside down. The
second 18 mm x 9mm batten is screwed and glued over the first one.
6.2 – Abaft the midsection, a triangular shaped timber is glued over the laminated keel
making a sort of a skeg. This is reinforced by two triangular shaped 4 mm marine
plywood panels that are glued at each side, increasing the total thickness of keel and
skeg abaft the midsection to 26 mm.
At the rear end corner, make a notch with the jigsaw to hold the small wheel held by
two s.s. flat bars bolted to the skeg.
6.3 – The two lateral supports are also laminated on the bottom employing the same 18
mm x 9 mm battens.
6.4 – Fillet the intersection of these three reinforcements with the bottom and then apply
a secondary lamination using a 100g/m2 glass cloth overlapping by about 50 mm the
basic hull lamination.

7 - Installing the deck and the cockpit

floor board.
7 – 1 – The first pieces to be installed are the two sheer clamps. First prepare two
18mm x 9mm wooden strips with the necessary length. Laminate these strips against the
sheers passing through the notches opened in the bulkheads top corners. Press them
against the topsides with small carpentry clamps until the glue sets. Attach the cleats
that join transoms to deck. Bevel the excess wood until the upper sides become
horizontal transversely where the topsides aren’t vertical.
7 – 2 – Before installing the deck, apply two coats of epoxy inside the compartments
that will be closed. Don’t forget to apply epoxy at the underside of the deck panel.
Apply glue to the contact surface and fasten it to the structure. Use the same s. s. self
tapping screws already recommended. Proceed in the same manner for the cockpit
floorboards.

8 – Finishing and painting the

superstructure
Fillet with a 5 mm radius spatula the internal edges of the cockpit. Also round the edges
of the cockpit seats. Apply a 100mm/m2 cloth saturated with epoxy resin all over the
superstructure. Sand the surface, apply an epoxy primer, sand again and the deck will
be ready to receive the finishing touches.
 9 – Finishing the dinghy.
After removing dust and other contaminants from the surface to be painted, using for
this purpose a cloth dampened with cleansing thinner; apply an epoxy primer coat all
over the hull. Sand thoroughly with dry and wet sandpaper. If necessary apply putty
where you find imperfections and sand once more. At this stage the hull is ready to
receive the finishing coat of paint.

10 – Installing the fittings.

10 – 1 - Inspection ports “Deck Plate” type. You can install up to three of these. Use a
large size ( 6 inches ). Put one in each lateral compartment and one in the forecastle.
10– 2 – Install a brake-water. This can be customised to taste. We suggest gluing over
the deck two cleats joined at centreline in a V shape, or more sophisticatedly, a round
coaming with an elliptical shape made from leftovers of plywood.
10 – 3 – Mast carling at deck. Under the deck, abaft the foc’sle bulkhead, it’s glued a
wooden reinforcement 18 mm thick. Only after this reinforcement is installed, drill the
carling hole. The mast step is a wooden block with a hole that coincides with mast
carling.
10 – 4 - Cockpit seats – These can be removed and are slipped into slots between cleats
fixed to these walls
10– 5 – Self draining plugs installed in the cockpit transom.
10 – 6 – Stainless steel pad eye for towing the dinghy
10 – 7 – Rudder fittings installed at the transom
10 – 8 – Wheel fixed to the skeg for transportation on ground.

11 – Lee boards, rudder and tiller

These components are built according to plans and don’t require to be sheathed with
fibreglass. They can be varnished or painted. We recommend employing a hard wood
for their construction.

12 – List of fittings
1 – Rudder gudgeons and pintles
2 – Wheel with two fixing bars.
3 – Single block with becket
4 – Single block
5 – Eye Straps
5 – 1 – Outhaul
5 – 2 – Sheet block.
5 – 3 – Foot block
5 – 4 – Cunninghan
6 – Closed clam cleats
6 – 1 – Outhaul
6 – 2 – Headsail tension
7 – Pad eye for towing
8 – Goose neck
9 – Three deck plates
10 – Two rowlocks
10 - Two drain plugs
11 - Tiller and tiller bars

Note: The main sheet system may be suppressed, using simply the arm to control
the sail. This in practice became proven to be more than adequate.
 DINGHY

CARAVELA
Ro ber t o Bar r o s Yac h t Des ig n
www.yac h t d es ig n .c o m.br
 DINGHY

CARAVELA
Ro ber t o Bar r o s Yac h t Des ig n
www.yac h t d es ig n .c o m.br
 DINGHY

CARAVELA
Ro ber t o Bar r o s Yac h t Des ig n
www.yac h t d es ig n .c o m.br
 RUBBING STRAKE
18mm x 18mm

18mm x 18mm
ROW LOCK

Mast

PAD
EYE
18mm x 18mm
18mm x 18mm

WHEEL
DINGHY
Scale.: 1:2
TO BE FILLETED RUBBING STRAKE CARAVELA
Ro ber t o B ar r o s Yac h t Des ig n
40mm x 18mm
www.yac h t d es ig n .c o m.br
 Sheer Clamp
(2x) 9mm x 18mm

PAD EYE

18mm x 40mm

KEEL STRINGER
(2x) 9mm x 18mm 18mm x 18mm
Sheer Clamps
(2x) 9mm x 18mm

BEAM
18mm x 18mm

Mast carlin
Wood
18mm x 100 x 120mm



R = 5mm R = 5mm

VERTICAL CLEAT
18mm x 18mm

Mast step block

Wood
Floorboard
DINGHY 18mm x 100 x 120mm inspection port MARINE PLAYWOOD 6mm

CARAVELA
Ro ber t o B ar r o s Yac h t Des ig n
www.yac h t d es ig n .c o m.br
 Sheer Clamp
(2x) 9mm x 18mm Leeboard Case
Section "A-A"
R = 5mm R = 5mm
Keel
DINGHY
CARAVELA
(2x) 9mm x 18mm
Ro ber t o Bar r o s Yac h t Des ig n
www.yac h t d es ig n .c o m.br
R = 5mm
DINGHY
CARAVELA
Ro ber t o Bar r o s Yac h t Des ig n
www.yac h t d es ig n .c o m.br
 Fibreglass encapsulation 18mm x 18mm

scale.: 1:2
Leeboard cases (Port/Stb) EPOXY PUTTY

To be filled
with putty
Epoxy Fillet
R=25mm

t
ille
yF
RUBBING

ox
Ep
STRAKE
Fibreglass
encapsulation
Floorboard 


plate.=2,00mm
scale.: 1:2
Back plate # 2,00mm

04 holes Ø 5mm

04 holes Ø 5mm




t
lle
Fi
y
pox
E

Epo
xy Fille
(int.) t

t
lle
Fi
y
ox
Ep Fibreglass
encapsulation
DINGHY
Fibreglass
encapsulation CARAVELA
Ro ber t o B ar r o s Yac h t Des ig n
www.yac h t d es ig n .c o m.br
 DINGHY

CARAVELA
Ro ber t o B ar r o s Yac h t Des ig n
www.yac h t d es ig n .c o m.br
 MARINE PLAYWOOD 4mm

TIMBER 18mm
mast

DINGHY

CARAVELA
MARINE PLAYWOOD 4mm
MARINE PLAYWOOD 4mm

Ro ber t o Bar r o s Yac h t Des ig n

www.yac h t d es ig n .c o m.br
 DINGHY
CARAVELA
Ro ber t o Bar r o s Yac h t Des ig n
www.yac h t d es ig n .c o m.br
 DINGHY

CARAVELA
Ro ber t o Bar r o s Yac h t Des ig n
www.yac h t d es ig n .c o m.br
 SCALE: 1:2
Thickness= 15,00 mm Thickness= 15,00 mm SCALE: 1:2
Thickness= 15,00 mm

Side top
View View

SCALE: 1:2
DINGHY

CARAVELA S.S # 2,00 mm

Ro ber t o Bar r o s Yac h t Des ig n

www.yac h t d es ig n .c o m.br