0% found this document useful (0 votes)
201 views5 pages

Sailor. For Global Communication: Sailor Transmitter T2131 and T2135 Error 83

The document discusses an error occurring in SAILOR transmitter models T2131 and T2135 where the output power is too low. This error is caused by either too high of a drive level or overload of the power amplifier, resulting in excess voltage. To address this, a protection circuit has been developed to adjust the drive level based on the amplifier voltage. Technicians should mount this new protection unit module and replace an existing cable, and the transmitter then needs to be recalibrated according to the service manual. The protection module can be ordered from S.P. Radio A/S by providing the transmitter's serial number.

Uploaded by

Camila Suarez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
201 views5 pages

Sailor. For Global Communication: Sailor Transmitter T2131 and T2135 Error 83

The document discusses an error occurring in SAILOR transmitter models T2131 and T2135 where the output power is too low. This error is caused by either too high of a drive level or overload of the power amplifier, resulting in excess voltage. To address this, a protection circuit has been developed to adjust the drive level based on the amplifier voltage. Technicians should mount this new protection unit module and replace an existing cable, and the transmitter then needs to be recalibrated according to the service manual. The protection module can be ordered from S.P. Radio A/S by providing the transmitter's serial number.

Uploaded by

Camila Suarez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Service Information

SAILOR. FOR GLOBAL COMMUNICATION


JANUARY 1995 NUMBER 160

SAILOR TRANSMITTER T2131 AND T2135 ERROR 83

We have noted an increased error rate as regards error 83, too low output power.

The Reason; for this error is either the drive level being too high or overload of the power amplifier.
Both of these conditions result in excess voltage in the power amplifier. This causes the
power supply to reduce the voltage, which creates a reverse voltage over the basis col-
lector diode in the output transistors resulting in a short circuit.

The Solution; A protection circuit has been developed, which adjust the drive level to the voltage in
the amplifier. This circuit “Protection Unit Module 19” is mounted. Furthermore, the trans-
mitter is calibrated as described in Chapter 3, “Calibration”, in the Service Manual.

Mounting; The existing cable 526917 between the power amplifier and the connection board is dis-
mounted and replaced by 730142, protection unit with cables. Please see the enclosed
diagram and outline.

Spares; Protection Unit Module 19 can be ordered free of charge at S.P. Radio A/S in return for
information about the transmitter’s serial number. The S.P. number is 730142.

If you should have any questions in relation to the above, please do not hesitate to contact the service
department at S.P. Radio A/S, Phone; +45 96 34 61 00 or fax; +45 96 34 61 01.

SERVICE INFORMATION S.P. RADIO A/S - AALBORG - DANMARK PAGE 1

Downloaded from www.Manualslib.com manuals search engine


JANUARY 1995 NUMBER 160

T2135 Modified Layout

COMBINER
UNIT
MODULE 12
J6 J5

POWER POWER

526516
AMPLIFIER A AMPLIFIER B
MODULE 11 MODULE 11
J4
16
5265

TR3

J1 J1
P4

P4
J1

TR2 TO MODULE (7) J4

P5 P5

J2 J3

P1

5-0-26412

PROTECTION
UNIT
MODULE 19

P1 P1
5-0-26411

5-0-26411
5-0-26419

5-0-26419

TR7 TR7

530703 530703
5-0-26414

P12 P14 P23


P21

J2
ST10

ST6

ST1
ST5

P11 P13 P20 P22


ST11

ST9
ST2

28371A

SERVICE INFORMATION S. P. RADIO A/S - AALBORG - DANMARK PAGE 2

Downloaded from www.Manualslib.com manuals search engine


JANUARY 1995 NUMBER 160

T2135 Previous Layout

COMBINER
UNIT
MODULE 12
J6 J5
POWER POWER

526516
AMPLIFIER A AMPLIFIER B
MODULE 11 MODULE 11
J4
6 1
5265

TR3

J1 J1
P4

P4
J1

TR2 TO MODULE (7) J4

P5 P5

J2 J3

P1

5-0-26412

To be
removed

P1 P1

TR7 TR7
917
526
5-0-26411 5-0-26411
5269
17
5-0-26414

P12 P14 P23


P21

J2
ST10

ST6

ST1
ST5

P11 P13 P20 P22


ST11

ST9
ST2

28371-SE

SERVICE INFORMATION S. P. RADIO A/S - AALBORG - DANMARK PAGE 3

Downloaded from www.Manualslib.com manuals search engine


JANUARY 1995 NUMBER 160

T2131 Modified Layout

60.100

POWER
AMPLIFIER
MODULE 11
16
5265

J1
P4

5-0-26411

P5
TO MODULE 7 J4

PROTECTION
UNIT
MODULE 19

P1
526918

5-0-26419

TR7

530703
5-0-26413

P7

J2
ST10

ST6

ST1
ST5

ST3
ST11

ST9
ST2

28372B

SERVICE INFORMATION S. P. RADIO A/S - AALBORG - DANMARK PAGE 4

Downloaded from www.Manualslib.com manuals search engine


JANUARY 1995 NUMBER 160

T2131 Previous Layout

60.100

POWER
AMPLIFIER
16 MODULE 11
5265

J1
P4

P5
TO MODULE 7 J4

To be
removed

P1
526918

TR7

5-0-26411 526917
5-0-26413

P7

J2
ST10

ST6

ST1
ST5

ST3
ST11

ST9
ST2

28372-SE

S.P. RADIO A/S • PORSVEJ 2 • DK-9200 AALBORG SV • DENMARK


PHONE INT. +45 96 34 61 00 • TELEX 69 789 SPRAD DK • TELEFAX INT. +45 96 34 61 01
E-MAIL: [email protected] • WEB: WWW.SAILOR.DK

SERVICE INFORMATION S. P. RADIO A/S - AALBORG - DANMARK PAGE 5

Downloaded from www.Manualslib.com manuals search engine

You might also like