Peterbilt Basics Bobcat

Finished Wood Toy Size

Full Size 3-1/2” W x 3-1/2” T x

7-7/16” L

Wood Toy Plans

All parts designed to be made with
common materials found in Home
Improvement stores.

ToymakingPlans.com © 2019
Peterbilt Basics
Bobcat

This clear-coated wood toy play set can be built with danish plywood, hardwoods,
softwoods or MDF. The finish is spray can Krylon or Rust-Oleum clear gloss. Spray
2 thin coats sanding each coat with 220 sandpaper when dry. Then spray 3 light
final coats of clear, sanding with 400 sandpaper after drying. Apply final coat without
sanding. All Krylon and Rust-Oleum paints and finishes are non-toxic when dry.

2 ToymakingPlans.com © 2019
 Warning: Read before copying. Peterbilt Basics Bobcat
The unauthorized reproduction or FULL-SIZE WOOD TO PLAN SET
distribution of this copyrighted work is
illegal. Criminal copyright infringement
including infringement without
monetary gain, is investigated by the
FBI and is punishable by up to 5 years
in federal prison and a fine of $250,000.

The plans and patterns in this planset can be

photo-copied for your personal use when building
the toys. ToymakingPlans.com plans and patterns
are copyrighted and cannot legally be copied,
distributed or shared with anyone for any other
purpose.
Make as many of each toy as you like! The wood
toys in this plan set are royalty-free. You have
the right to build any quantity of these toys for
any reason.

ToymakingPlans.com is dedicated to providing you with the

information and ideas you need to develop your skills as a toymaker.
We welcome your comments and any suggestions about this
collection of toy plans.
Email: [email protected]
©2019 ToymakingPlans.com - All rights reserved - 051719
Note to the Readers: Due to different conditions, tools, and
individual skills, ToymakingPlans.com assumes no responsibility Color & Natural Wood Pictorial Views............................ 4-9
for any damages, injuries suffered, or losses incurred as a result of
following the information published in this plan set. Before beginning Patterns Index, Parts List & Exploded View............... 10-11
any project review instructions carefully. If any doubts or questions
remain consult local experts or authorities. Assembly Steps.......................................................... 12-13
Copyright Information: Plans and patterns in this Plan Set
can be photo-copied for personal use when building the toys. Plan Views.................................................................. 14-15
ToymakingPlans.com plans and patterns are copyrighted and cannot
be distributed or shared for free or for any other reason. Full-Size Patterns....................................................... 16-17
ToymakingPlans.com © 2019 3
Peterbilt Basics
Bobcat

This clear-coated wood toy can be built with danish plywood, hardwoods, softwoods or MDF. The finish is spray can Krylon or Rust-
Oleum clear gloss. Spray 2 thin coats sanding each coat with 220 sandpaper when dry. Then spray 3 light final coats of clear, sanding
with 400 sandpaper when dry. Apply final coat without sanding. All Krylon and Rust-Oleum paints and finishes are non-toxic when dry.

4 ToymakingPlans.com © 2019
 Peterbilt Basics
Bobcat

This clear-coated wood toy can be built with danish plywood, hardwoods, softwoods or MDF. The finish is spray can Krylon or Rust-
Oleum clear gloss. Spray 2 thin coats sanding each coat with 220 sandpaper when dry. Then spray 3 light final coats of clear, sanding
with 400 sandpaper when dry. Apply final coat without sanding. All Krylon and Rust-Oleum paints and finishes are non-toxic when dry.

ToymakingPlans.com © 2019 5
Peterbilt Basics
Bobcat

This color painted wood toy can be built with danish

plywood, hardwoods, softwoods or MDF. The finish is spray
can Krylon or Rust-Oleum. Spray 2 coats of primer sanding
each coat with 220 sandpaper when dry. Then spray 3 coats
of color sanding with 400 sandpaper when dry. Apply final
coat without sanding. All Krylon and Rust-Oleum paints and
finishes are non-toxic when dry.
6 ToymakingPlans.com © 2019
 Peterbilt Basics
Bobcat

This color painted wood toy can be built with danish plywood, hardwoods, softwoods or MDF. The finish is spray can Krylon or Rust-
Oleum. Spray 2 coats of primer sanding each coat with 220 sandpaper when dry. Then spray 3 coats of color sanding with 400
sandpaper when dry. Apply final coat without sanding. All Krylon and Rust-Oleum paints and finishes are non-toxic when dry.
ToymakingPlans.com © 2019 7
Peterbilt Basics ACTUAL SIZE
Bobcat
TOP VIEW

Finished Wood Toy Size

3-1/2” W x 3-1/2” T x
7-7/16” L

SIDE VIEW
8 ToymakingPlans.com © 2019
 Peterbilt Basics
Bobcat

ACTUAL SIZE

REAR VIEW FRONT VIEW

ToymakingPlans.com © 2019 9
Peterbilt Basics Bobcat BOBCAT PATTERNS INDEX

3
7

6 9

10

11
2

page 16 page 17

ATTENTION:
FULL-SIZE PLAN VIEWS ARE ON PAGE 14-15.

BOBCAT PARTS LIST

1. 1-1/2” x 3-1/16” x 4-1/4” make 1
2. 1/4” diameter x 2-9/16” make 2
3. 1” diameter x 1/8” make or buy 4*
4. 1-1/2” diameter x 1/2” make or buy 4*
5. 3/4” diameter x 1/8” make or buy 1*
6. 1” x 2-3/8” x 2-15/16” make 1
7. 1/4” diameter x 3/4” make 1
8. 1/4” diameter x 3-1/2” make 2
9. 1/4” x 1-7/8” x 2” make 2
10. 1/2” x 2-3/8” x 4-3/4” make 2
11. 3/4” diameter x 3/8” make 4
10 ToymakingPlans.com © 2019 *Buying info for Parts 3, 4 & 5 is on page 11.
 BOBCAT EXPLODED VIEW ATTENTION: Peterbilt Basics
FULL-SIZE PLAN VIEWS ARE ON PAGE 14-15. Bobcat
Part 3
Finished Wood Toy Size www.craftparts.com
3-1/2” W x 3-1/2” T x 11
#JC6210 Buy 4
7-7/16” L 1” dia. x 1/8” thick disc
7

Part 4
1 www.craftparts.com
10
#TWF150 Buy 4
3 1-1/2” dia. x 1/2” thick
Wood Toy Wheels
3 4 Hole size 1/4”
4 5

11
11

10

9
4

4
3
6

2
3

Part 5
8
11 www.craftparts.com
#JC5712 Buy 1
3/4” dia. x 1/8” thick disc

ToymakingPlans.com © 2019 11
Peterbilt Basics BOBCAT ASSEMBLY STEPS
Bobcat 11

10

5 1

10
Step 2 11
Step 1 Assembly
Assembly 8

Step 1: Step 2: Step 3:

Using the Plan Views on pages 14-15 as a guide, glue Using the Plan Views on pages 14-15 as a guide, Using the Plan Views on pages 14-15 as a guide,
Part 5 steering wheel to Part 1. Let the assembly dry glue Part 7 exhaust stack to Step 1 Assembly. Let dry insert Part 8 thru two Part 10’s & Part 1. Glue two
before proceeding. before proceeding. Part 11’s to ends of Part 8 allowing two Part 10’s to be
snug against Part 10’s and rotate freely in the Step 2
3
Assembly. Let dry before proceeding.

10 3
4
6
11

4
10
9
2

9
Step 3
4 3
Assembly 2

11 3
4
Step 4
8
Assembly
Step 4:
Glue two Part 9’s to Part 6. Let dry. Insert Part 8 Step 5:
thru two Part 10’s & Parts 9-6-9. Glue two Part Glue four Part 3 hubcaps to four Part 4 wheels. Insert two
11’s to ends of Part 8 allowing Parts 9-6-9 to be Part 2 axles into the Step 4 Assembly and glue the four
snug against Part 10’s and rotate freely in Step 3 Part 3-4 assemblies to ends of Part 2’s in a position that
Assembly. Let dry before proceeding. allows Part 2’s to rotate freely in the Step 4 Assembly.
12 ToymakingPlans.com © 2019
 Peterbilt Basics
Bobcat

ToymakingPlans.com © 2019
13
Peterbilt Basics Plan Views
Bobcat 0 printer scale 1 2 3
ATTENTION:
ACTUAL SIZE
8 8 THESE FULL-SIZE PLAN VIEWS ARE FOR
11 11
ASSEMBLY REFERENCE. INDIVIDUAL
3 3 PATTERNS ON PAGES 16-17.

4 4 10 9

7 TOP
1 2 6
2 PLAN VIEW

4 4 10 9

3 3

11 11

TIP:
Finished Wood Toy Size 1
3-1/2” W x 3-1/2” T x To print paper plan views and patterns from your computer only print pages
14-17 landscape mode. Pages are printed in black to conserve ink. Check
7-7/16” L printer printed size accuracy by measuring the printer scale on each
7
pattern with a ruler. If printed size is not 100% adjust printer settings.
5

6
8

11

10 9

SIDE
3 PLAN VIEW 3

2 2 11

4 4

14 ToymakingPlans.com © 2019
 Peterbilt Basics
0 printer scale 1 2 3 Bobcat
ACTUAL SIZE

ATTENTION:
THESE FULL-SIZE PLAN VIEWS ARE FOR FRONT
ASSEMBLY REFERENCE. INDIVIDUAL PATTERNS PLAN VIEW
ON PAGES 16-17.

1 1

7 7

10 10 10 5 10
11 11 11 11
5
8 8
9 9

3 3 3
3

11 11 11 11
2 2
8 8

6 6

4 FRONT 4 4 REAR 4
PLAN VIEW PLAN VIEW

TIP:
To print paper plan views and patterns from your computer
only print pages 14-17 landscape mode. Pages are printed in
black to conserve ink. Check printer printed size accuracy
by measuring the printer scale on each pattern with a ruler. If
printed size is not 100% adjust printer settings.

ToymakingPlans.com © 2019 15
Peterbilt Basics
Bobcat 0 printer scale 1 2 3
TIP: ACTUAL SIZE

To print paper plan views and patterns from your computer only print
pages 14-17 landscape mode. Pages are printed in black to conserve
Part 3
ink. Check printer printed size accuracy by measuring the printer
scale on each pattern with a ruler. If printed size is not 100% adjust www.craftparts.com
printer settings. #JC6210 Buy 4
1” dia. x 1/8” thick disc
3

Part 4
www.craftparts.com
#TWF150 Buy 4
1/4” dia. x
1 1-1/2” dia. x 1/2” thick
1
3/8” deep
Wood Toy Wheels
Hole size 1/4”
4
1/4” dia.
hole thru

5/16” dia.
hole thru
(3 places)

1. 1-1/2” x 3-1/16” x 4-1/4” make 1

5
Part 5 2. 1/4” diameter x 2-9/16” make 2
2 www.craftparts.com 3. 1” diameter x 1/8” make or buy 4
#JC5712 Buy 1 4. 1-1/2” diameter x 1/2” make or buy 4
3/4” dia. x 1/8” thick disc
5. 3/4” diameter x 1/8” make or buy 1

16 ToymakingPlans.com © 2019
 Peterbilt Basics
TIP: 0 printer scale 1 2 3 Bobcat
To print paper plan views and ACTUAL SIZE
patterns from your computer only
print pages 14-17 landscape mode.
Pages are printed in black to 8
conserve ink. Check printer printed
size accuracy by measuring the
6
printer scale on each pattern with
a ruler. If printed size is not 100%
adjust printer settings.

9
6
6
1/4” dia.
9
hole thru 9

10

5/16” dia. 6. 1” x 2-3/8” x 2-15/16” make 1

hole thru
10 7. 1/4” diameter x 3/4” make 1
8. 1/4” diameter x 3-1/2” make 2
9. 1/4” x 1-7/8” x 2” make 2
11 10. 1/2” x 2-3/8” x 4-3/4” make 2
10
11. 3/4” diameter x 3/8” make 4
5/16” dia.
hole thru

1/4” dia.
hole thru
ToymakingPlans.com © 2019 17