GP-32 Ome-44200-E3

Back
DGPS NAVIGATOR
GPS NAVIGATOR
GP-37 /GP-32
The paper used in this manual
is elemental chlorine free.
FURUNO Authorized Distributor/Dealer
9-52 Ashihara-cho,
Nishinomiya 662-8580, JAPAN
Telephone : 0798-65-2111
Fax : 0798-65-4200
All rights reserved. Printed in Japan FIRST EDITION : MAY. 2002

E3 : FEB. 23, 2007
Pub. No. OME-44200
( YOSH ) GP-32/37 *00080928811*

*00080928811*
*00080928811*
SAFETY INSTRUCTIONS
Safety Instructions for the Operator
WARNING NOTICE
Do not open the equipment. Be sure the power supply is compatible
with the equipment.
Only qualified personnel should work inside
the equipment. Incorrect power supply may cause the
equipment to overheat.
Do not disassemble or modify the
equipment. The useable temperature range for the
antenna unit is -25°C to 70°C;
Fire, electrical shock or serious injury can -15°C to 55°C for the display unit.
result.
Use of the equipment out of those ranges
Immediately turn off the power at the may damage the equipment.
switchboard if the equipment is emitting
smoke or fire.
Continued use of the equipment can cause

fire or electrical shock. Contact a FURUNO
agent for service.
Use the proper fuse.
Use of a wrong fuse can damage the

equipment or cause fire.
i
Safety Instructions for the Installer
WARNING NOTICE
Do not open the cover unless totally Observe the following compass safe
familiar with electrical circuits and distances to prevent interference to a
service manual. magnetic compass:
Improper handling can result in electrical Standard Steering

compass compass
shock.
Display
0.80 m 0.55 m
unit
Turn off the power at the switchboard
before beginning the installation.
Fire or electrical shock can result if the

power is left on.
Be sure that the power supply is

compatible with the voltage rating of
the equipment.
Connection of an incorrect power supply

can cause fire or equipment damage. The
voltage rating of the equipment appears
on the label above the power connector.
Use the proper fuse.
Use of a wrong fuse can damage the

equipment or cause fire.
ii
TABLE OF CONTENTS
FOREWORD ................................... v 6. ALARMS................................... 29

SYSTEM CONFIGURATION.......... vi 6.1 Arrival Alarm, Anchor Watch
WHAT IS WAAS?.......................... vii Alarm.........................................29
EQUIPMENT LISTS ..................... viii 6.2 XTE (Cross Track Error) Alarm..30
6.3 Speed Alarm..............................31
1. OPERATIONAL OVERVIEW...... 1 6.4 WAAS/DGPS Alarm ..................31
1.1 Controls ...................................... 1 6.5 Time Alarm ................................31
1.2 Turning On and Off Power .......... 2 6.6 Trip Alarm..................................32
1.3 Adjusting Brilliance and Contrast 2 6.7 Odometer Alarm ........................32
1.4 Display Modes ............................ 3 6.8 Buzzer Type Selection...............32
1.5 Menu Overview........................... 7
1.6 Simulation Display ...................... 8 7. OTHER FUNCTIONS ............... 33
7.1 Calculating Range, Bearing,
2. PLOTTER DISPLAY OVERVIEW9 TTG and ETA ............................33
2.1 Choosing the Display Range....... 9 7.2 WAAS Setup .............................34
2.2 Shifting the Cursor ...................... 9 7.3 DGPS setup ..............................35
2.3 Shifting the Display ................... 10 7.4 Bearing Reference.....................37
2.4 Centering Own Ship’s Position.. 10 7.5 Magnetic Variation .....................38
2.5 Changing Track Plotting Interval, 7.6 Geodetic Chart System .............38
Stopping Plotting....................... 10 7.7 Units of Measurement ...............38
2.6 Erasing Track.............................11 7.8 Position Display Format.............39
7.9 Time Difference (using local time),
3. WAYPOINTS (MARKS) ............ 13 Time Format ..............................39
3.1 Entering Waypoints................... 13
7.10 GPS Setup ................................40
3.2 Entering the MOB Mark ............ 15
7.11 User Display Setup....................41
3.3 Displaying Waypoint Name ....... 16
7.12 Resetting Trip and Odometer
3.4 Operations on the Waypoint List 16
Distances ..................................42
3.5 Erasing Waypoints .................... 17
7.13 Uploading, Downloading
3.6 Speed for Calculating Time-to-Go,
Waypoint, Route Data................43
Estimated Time of Arrival .......... 18
7.14 Language ..................................46
4. ROUTES ................................... 19 8. MAINTENANCE &
4.1 Creating Routes........................ 19
TROUBLESHOOTING ............. 47
4.2 Editing Routes .......................... 23
8.1 Maintenance..............................47
4.3 Erasing Routes ......................... 25
8.2 Displaying the Message Board ..47
8.3 Replacing the Fuse....................48
5. DESTINATION .......................... 27
8.4 Replacing the Battery ................48
5.1 Setting Destination by Cursor ... 27
8.5 Satellite Monitor Display ............49
5.2 Setting Destination by Waypoint 27
8.6 Diagnostics................................49
5.3 Setting Route as Destination..... 28
8.7 Clearing Data ............................50
5.4 Setting User Waypoint as
Destination................................ 28
5.5 Canceling Destination ............... 28
iii
9. INSTALLATION ........................53 OUTLINE DRAWINGS
9.1 Installation of Display Unit......... 53 INTERCONNECTION DIAGRAMS
9.2 Installation of Antenna Unit ....... 54
9.3 Wiring ....................................... 55 INDEX ................................... Index-1
9.4 Initial Settings ........................... 56
Declaration of Conformity
APPENDIX.................................AP-1
SPECIFICATIONS .....................SP-1
iv
FOREWORD
A Word to the Owner of the Features
GP-37, GP-32 The GP-37/GP-32 is a totally integrated GPS
Congratulations on your choice of the GP-37 receiver and video plotter, and mainly
DGPS Navigator, GP-32 GPS Navigator. consists of a display unit and an antenna unit.
The GP-37 is additionally equipped with a
For over 50 years FURUNO Electric DGPS beacon receiver, built in the display
Company has enjoyed an enviable reputation unit.
for innovative and dependable marine
electronics equipment. This dedication to The high sensitivity GPS receiver tracks up to
excellence is furthered by our extensive 13 satellites (12 GPS, 1 WAAS)
global network of agents and dealers. simultaneously. An 8-state Kalman filter
ensures optimum accuracy in determination
Your navigator is designed and constructed to of vessel position, course and speed.
meet the rigorous demands of the marine
environment. However, no machine can The main features of the GP-37/GP-32 are
perform its intended function unless installed,
operated and maintained properly. Please • A DGPS beacon receiver may be
carefully read and follow the recommended connected to the GP-32 to add DGPS
procedures for installation, operation, and capability.
maintenance. • WAAS capability.
• Storage for 999 waypoints and 50 routes
We would appreciate hearing from you, the • Alarms: Arrival/Anchor Watch, XTE
end-user, about whether we are achieving our (Cross-track Error), Trip, Odometer, Time,
purposes. WAAS/DGPS, and Speed.
• Man overboard feature records position at
Thank you for considering and purchasing
time of man overboard and provides
FURUNO equipment.
continuous updates of range and bearing
when navigating to the MOB position.
• Bright 95 x 60 mm LCD with adjustable
contrast and brilliance.
• Autopilot (option) may be connected, and
steering data output to the autopilot.
• Unique Highway display provides a graphic
presentation of ship’s progress toward a
waypoint.
• User displays definable by operator.
• Waypoint and route data can be uploaded
from a PC and downloaded to a PC.
v
SYSTEM CONFIGURATION
Note: This equipment is intended for use on marine vessels. Do not use it in other applications.
ANTENNA UNIT
GPA-019
PROCESSOR UNIT*
FURUNO GPS NAVIGATOR
NAVIGATOR
PERSONAL COMPUTER
* = With DGPS beacon receiver
: Standard Supply
: Option
12/24 VDC
GP-37 system configuration
ANTENNA UNIT
GPA-017
PROCESSOR UNIT
FURUNO GPS NAVIGATOR
NAVIGATOR
DGPS BEACON RECEIVER
PERSONAL COMPUTER
: Standard Supply
: Option
12/24 VDC
GP-32 system configuration
This GPS receiver complies with Canadian standard RSS-210 (Low Power
License-Exempt Radio communication Devices).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
vi
WHAT IS WAAS?
WAAS, available in North America, is a provider in the worldwide SBAS (Satellite Based
Augmentation System) navigation system. An SBAS provider furnishes GPS signal corrections
to SBAS users, for even better position accuracy, typically better than three meters. Two more
SBAS providers are also currently under development, MSAS (Multi-Functional Satellite
Augmentation System) for Japan and EGNOS (Euro Geostationary Navigation Overlay Service)
for Europe. All providers will be compatible with one another, thus providing “seamless” position
fixes to SBAS users.
At the time of this software release, WAAS is still in the developmental phase. During this
developmental phase, which may last several years, there is no guarantee of the accuracy,
integrity, continuity, or availability of the WAAS signal. Therefore, FURUNO will accept no
responsibility for the use of the signal for other than the above stated purpose. It is the user’s
responsibility to exercise common prudence and navigational judgment when using the WAAS
signal.
150°W 120°W 90°W 60°W 30°W 0 30°E 60°E 90°E 120°E 150°E
60°N 60°N
40°N EGNOS 40°N

MSAS
20°N 20°N
122 120 131 134

0 0
WAAS
20°S 20°S
40°S 40°S
60°S 60°S
150°W 120°W 90°W 60°W 30°W 0 30°E 60°E 90°E 120°E 150°E
Satellite, Region Position Expected operations capability

120, AOR-E 15.5°W WAAS: 2003
122, AOR-W 54°W EGNOS: 2004
131, IOR 64.5°E MSAS: 2005
134, POR 178°E
Note: This manual uses “WAAS” when referring to any SBAS provider.
vii
EQUIPMENT LISTS
Standard supply
Name Type Qty Remarks
Display GP-37 With hanger, knob
1
Unit GP-32
Antenna GPA-019 1 For GP-37, w/10 m cable
Unit GPA-017 1 For GP-32, w/10 m cable
Installation CP20-02310 1 set • Power/data cable (1 pc.)
Materials (Type: MJ-A7SPF0009-020C, Code No.: 000-159-686-10)
• Tapping screw (4 pcs.)
(Type: 5X20, Code No.: 000-162-608-10)
Spare Parts SP20-01001 1 set Fuse (2 pcs.)
(Type: FGMB 125V 1A PBF, Code No.: 000-157-478-10)
Template C42-00201 1 Code No. 000-809-299, flush mounting template
Hard Cover FP14-02801 1 Code No. 004-366-960
Optional equipment
Name Type Code No. Qty Remarks
Right Angle NO.13-QA330 000-803-239 1 For mounting the antenna
Antenna Base unit, choose one
L-type Antenna NO.13-QA310 000-803-240 1
Base
Handrail NO.13-RC5160 000-806-114 1
Antenna Base
Mast Mounting CP20-01111 004-365-780 1 set
Kit
Cable Assy. MJ-A7SPF0009-020C 000-159-686-10 1
Flush Mounting OP20-29 000-041-405 1 set For flush mounting the
Kit F display unit, choose one
Flush Mounting OP20-17 000-040-720 1 set
Kit S
viii
1. OPERATIONAL OVERVIEW
1.1 Controls
Cursor Pad
• Shifts cursor (cursor displayed)
and display (cursor off).
• Selects items on menus.
Press once: Zoom, centering, • Enters alphanumeric data.
or escapes from current opera-
tion, depending on display in MENU ENT Registers items on menus.
use.
Press twice: Opens menu.
Chooses display mode. DISP GOTO Sets/cancels destination.
MARK Momentary press: Inscribes mark.

MOB
Long press: Inscribes MOB mark.
DIM Momentary press: Turns

PWR
power on. With the power on, press
to adjust dimmer and contrast.
Long press: Turns power
off.
Control panel
How to attach and remove the hard cover
To attach the hard cover, set it to the display unit at an angle.
To remove the hard cover, do as follows:
Press at arrows
and pull toward
you to remove.
1
1.2 Turning On and Off Power Turning off the power
Turning on the power Press and hold down the [DIM/PWR] key until
the screen goes blank (about three seconds).
Press the [DIM/PWR] key. The unit beeps
The time remaining until the power is turned
and then starts up with the last-used display
off is counted down on the display.
mode.
Note: The example screens shown in this

manual may not match the screens you see
1.3 Adjusting Brilliance and
on your display. The screen you see depends Contrast
on your system configuration and equipment 1. Press the [DIM/PWR] key momentarily.
settings. The display shown below appears.
Your equipment takes about 90 seconds to BRILL (1~8)

find its position when turned on for the very 4
first time. Thereafter it typically takes about
CONTRAST (0~63)
12 seconds.
41
The equipment shows receiver status EXIT:[ENT]
indication at the top left-hand corner in most
display modes. The table below shows these Brilliance and contrast adjustment window
indications and their meanings. 2. To adjust the brilliance, press ▲ or ▼.
Current setting is shown to the right of ▲.
Receiver status indications Maximum setting is 8.
Indication Meaning 3. To adjust the contrast, press ◄ or ►.
2D 2D GPS position fix Current setting is shown to the right of ►.
3D 3D GPS position fix
Maximum setting is 63.
4. Press the [ENT] key to finish.
D2D 2D DGPS position fix
D3D 3D DGPS position fix
Note: If the last-used contrast setting is 36 or
W2D 2D WAAS position fix
higher, the equipment starts up with that
W3D 3D WAAS position fix
setting. If the setting is 35 or lower, the
DOP* 2D: HDOP larger than 4
equipment starts up with setting 36.
3D: PDOP larger than 6
SIM Simulation mode
* = DOP (Dilution of Precision) is the index of

position accuracy and is the distribution
pattern of satellites used in position fixing.
Generally, the smaller the figure the better the
position accuracy.
2
1.4 Display Modes

Your unit has five display modes: Plotter Display, Highway Display, Steering Display, Nav Data
Display and User Display (digital data and speedometer). Press the [DISP] key to choose a
display mode. Each time the key is pressed, the display mode changes in the sequence shown
below.
20 D2D
n
10 30 [5 m]
[DISP] key COG: X

357°
0 40 SOG:
10.0 kt
SOG 0 9.9 KT
60
34°44.000N 135°21.000E
[User Display: Speedometer] [Plotter Display]

(Display format
depends on user setting.) [DISP] key
[DISP] key
004
POWER(V) SOG(KT)
BRG 242° [+]
12.1 9.9 COG 357° 0.05

0.5 0.05
TRIP(NM) COG(°)
RNG17.5
n
m
9.99 5.6 SOG10.0

k
t XTE 0.05 n
m
[User Display: Digital Data] [Highway Display]

(Display format
depends on user setting.)
[DISP] key [DISP] key
D2D MAG CURSOR 15:37

D2D 02-FEB-02 15:37:40
300 330 N 30 60 E
34°44. 000' N
135°21. 000' E
[DISP] key SOG: 10.0 kt COG: 357°
RNG: 17.5 nm BRG: 242°
SOG: 10.0 kt COG: 357° TTG: 1H30M ETA: 12:30
[Nav Data Display] [Steering Display]
Display modes (default user displays)
Note 1: The unit measures distances up to 9999 nm. Any distance greater than 9999 nm is
shown as “*999”.
Note 2: Position data can be shown in latitude and longitude or TDs (Loran C or Decca).
3
Plotter display
The plotter display traces own ship’s track, and shows position, bearing to cursor, range to
cursor, horizontal display range setting and receiver status.
Receiver status
(See table on page 2.) Own ship mark (blinking)
D2D X Waypoint mark

(Shape selectable)
Horizontal display [ 40 n ]
m Boat's track
range setting
BRG: +
Bearing 180°
to cursor*
RNG: + Cursor
Range 12.0 mn (Displayed six seconds.)
to cursor*
34°44.000N 135°21.000E Cursor position
(Own ship position when
* = COG and SOG replace bearing to cursor and cursor is not displayed.)
range to cursor when the cursor is not displayed.
Plotter display
Highway display
The highway display provides a 3-D view of own ship’s progress toward destination (waypoint).
Nav data is also shown.
Direction to steer (to return to course)

Appears to right or left of centerline
Bearing from own ship to depending on direction to steer;
destination waypoint : Steer right, : Steer left.
CURSOR Destination waypoint name
BRG 11° [+]

"CURSOR" (cursor-selected
destination) or waypoint name
Course
over
COG 11° 0.5
0.3 0.5
Destination waypoint
Moves forward as boat
nears destination.
ground
RNG 9.0 n
m I I I
NI I I I
∆ C (Delta Course)
Speed
over
SOG 12.5 k
t
XTE
0.05 n
m
The boat mark displays
course as follows:
When no waypoint is set;
ground
The mode is North-up and
the arrow shows boat's course.
Range from Analog XTE (Cross-track error) scale When a waypoint is set;
own ship to Arrow shifts with boat's XTE. When the The arrow shows boat's
destination arrow is aligned with the centerline course towards destination.
waypoint the boat is on course. The arrow blinks if Digital XTE indication
boat's XTE is greater than XTE scale (in nautical miles)
range. "N" (North) is displayed instead of
the arrow when no destination is set.
Highway display
4
Steering display
The steering display provides steering information such as ship’s speed, course, range, bearing,
ETA and TTG.
Receiver status
Bearing reference (MAG or TRUE)
Destination (CURSOR or waypoint name)
Time
D2D MAG CURSOR 04:32 Bearing from own ship
▼ to destination
W 300 330 N 30 60 E Bearing scale
I I I I I I I I I I I I I
Own ship mark
Speed over ground SOG: 12.5 kt COG: 354° Course over ground
Range from own ship RNG: 0.16 nm BRG: 60° Bearing

to destination
TTG: 1H 30M ETA: 12:30 Estimated Time of
Time-To-Go Arrival at destination
to destination (*9:*9 shown when
(*9H*9M is displayed ETA is over 99h59min.)
when TTG is over 99 h59min.)
Steering display
Nav data display
The nav data display shows receiver status, position in latitude and longitude (or TDs), course
over ground, speed over ground, date and time.
Receiver status
D2D 10-JAN-02 16 :44 :15 Date and time
34°44.000' N
Position in latitude
and longitude
135°21.000' E
Speed over ground SOG: 12.5 kt COG: 7° Course over ground
Nav data display
5
User displays
Two user displays are available, digital and speedometer.
Digital display
The digital display shows digital navigation data. The user may choose what data to display in
one to four cells. The choices of data are time, speed over ground, cross-track error, odometer
distance, position, course over ground, time-to-go to destination, trip distance, power source
voltage, range and bearing to waypoint, and estimated time of arrival at destination.
POWER(V) SOG(KT)
12.1 9.9
TRIP(NM) COG(°)
9.99 5.6
Digital display (default display)
Speedometer display
The speedometer display provides both digital and analog displays of speed over ground.
20
10 30
0 40
SOG 0 9.3 KT
60
Speedometer display
6
1.5 Menu Overview

OFF
Most operations of your unit are carried out DISTANCE
through the menu. Below is a quick AUTO
introduction to how to choose a menu and
change menu settings. If you get lost in Track recording options
operation, press the [MENU] key to return to 5. Press ▲ or ▼ to choose option desired.
the MAIN MENU. For your reference, a 6. Press the [ENT] key to register your
complete menu tree appears in the Appendix. selection.
7. Press the [MENU] key twice to close the
1. Press the [MENU] key once or twice to menu.
display the menu.
One press: Steering display, nav data How to enter alphanumeric data
display and user display.
Two presses: Plotter display, highway In some instances it is necessary to enter
display. alphanumeric data. The example below
shows how to enter a time difference of -6:30,
MAIN MENU to use local time instead of UTC time.
WAYPOINTS MESSAGES 1. Press the [MENU] key once or twice to

ROUTES SATELLITE
PLOTTER USER DISP display the menu.
ALARMS GPS SETUP 2. Choose SYS SETUP and then press the
ERASE SYS SETUP
WAAS/DGPS I/O SETUP [ENT] key.
CALCULATE TD SETUP
SYSTEM SETUP
Main menu LANGUAGE : ENGLISH
DATUM : WGS84
2. Operate the cursor pad to choose a menu UNITS : nm, kt
and then press the [ENT] key. For TIME DIFF : +00 : 00
TIME DISP : 24HOUR
example, choose PLOTTER and then
TEST?
press the [ENT] key. SIMULATOR?
EXCHANGE BATTERY?
PLOTTER SETUP
SYSTEM SETUP menu
TRACK REC : DISTANCE
INTERVAL : 0.10 nm 3. Choose TIME DIFF.
BRG. REF. : MAG 4. Press the [ENT] key. A cursor
MAG. VAR. : AUTO E16
WPT NAME : DSP GOTO circumscribes “+”. This cursor appears
TTG/ETA SPD : AUTO whenever selected data can be changed
TRACK MEMORY USED 1% with the cursor pad.
PLOTTER SETUP menu SYSTEM SETUP

3. Use ▲ or ▼ to choose menu item. For LANGUAGE : ENGLISH
DATUM : WGS84
example, choose TRACK REC. UNITS : nm, kt
4. Press the [ENT] key. A window shows the TIME DIFF : +00 : 00
TIME DISP : 24HOUR
options for the item selected. (The TEST?
illustration at the top of the next shows the SIMULATOR?
EXCHANGE BATTERY?
options available for TRACK REC.)
SYSTEM SETUP menu,
TIME DIFF selected
7
5. Press ▲ to display “-“. 6. Press the [ENT] key, use the cursor pad
6. Press ► to send the cursor to the next to enter speed to use for the simulation,
digit. and then press the [ENT] key.
7. Press ▲ or ▼ to display “0.” 7. Press the [ENT] key.
8. Press ► to send the cursor to the next 8. Choose course (AUTO or MAN) and then
digit. press the [ENT] key. For manual entry of
9. Press ▲ or ▼ to display “6.” course, press the [ENT] key, enter course
10. Press ► to send the cursor to the next with the cursor pad, and then press the
digit. [ENT] key. The AUTO course tracks a
11. Press ▲ or ▼ to display “3.” circular course.
12. Press ► to send the cursor to the last Note: Course must be AUTO to set
digit. simulation destination.
13. Press ▲ or ▼ to display “0.”
9. Press the [ENT] key, enter latitude with
14. Press the [ENT] key.
the cursor pad, and then press the [ENT]
15. Press the [MENU] key twice to finish.
key.
10. Press the [ENT] key, enter longitude, and
then press the [ENT] key.
1.6 Simulation Display 11. Press the [MENU] key twice.
The simulation display provides simulated 12. Choose the PLOTTER display with the
operation of this unit. You may set the speed [DISP] key. SIM appears at the upper
manually and course manually or left-hand corner when the simulator
automatically. All controls are operative - you display is active.
may enter marks, set destination, etc.
Simulation mode active
1. Press the [MENU] key once or twice to SIM

display the menu. n
[ 40 m ]
2. Choose SYS SETUP and then press the
COG: Course traced
[ENT] key. in AUTO course
3. Choose “SIMULATOR?” and then press 82°
SOG:
the [ENT] key. (Note that position shown k
9.0 t
depends on language selected on the
SYS SETUP menu. After changing the 34°44.000N 135°21.000E
language, the memory is cleared.)
Simulator display, auto course selected
SIMULATOR
13. To turn off the simulator display, choose
MODE : OFF OFF at step 5 in this procedure, press the
SPEED : 20 kt
COURSE : AUTO [ENT] key and then press the [MENU] key
LAT : 38°00'N twice to finish.
LON : 123°00'W
Note: If the power is turned off while the
simulator display is in use, the indication
SIMULATOR menu SIMULATION MODE appears at the top of
4. The cursor is selecting MODE. Press the the screen at the next power up, in addition to
[ENT] key. A window shows the choices the indication SIM. SIMULATION MODE
ON and OFF. disappears when any key is pressed,
5. Choose ON and then press the [ENT] key. however the simulation mode continues.
8
2. PLOTTER DISPLAY OVERVIEW
2.1 Choosing the Display 3. Use ▲ (increase) or ▼ (decrease) to
Range choose range desired.
4. Press the [ENT] key to close the zoom,
You may choose the display range on the ship centering window.
plotter and highway displays. The horizontal
range in the plotter display is available among
0.02 (40 yd), 0.05 (101 yd), 0.1 (202 yd), 0.2 2.2 Shifting the Cursor
(405 yd), 0.5, 1, 2, 5, 10, 20, 40, 80, 160 and
320 nautical miles. (Nautical mile is the Use the cursor pad to shift the cursor. The
default unit of display range. Display range cursor moves in the direction of the arrow or
may also be shown in kilometers or miles. diagonal pressed on the cursor pad.
Ranges shorter than the 0.5 nm are also
shown in yards or meters on the plotter Cursor state and data
display.) The horizontal range in the highway Cursor state determines what data is shown
display is available among 0.2, 0.4, 0.8, 1, 2, on the display.
4, 8 and 16 nautical miles.
Cursor turned on
1. Press the [MENU] key. The zoom, ship
Cursor position is displayed in latitude and
centering window appears.
longitude or TDs (depending on menu
setting) at the bottom of the plotter display
ZOOM IN/OUT?
when the cursor is on. The range and bearing
SHIP TO CENTER?
from own ship to the cursor appear at the
Quit?
left-hand side of the display.
PRESS [MENU] TO SEE Bearing from own Own ship Cursor
THE MAIN MENU. ship to cursor
D2D
Zoom, ship centering window n
[ .02 m ]
Note: “SHIP TO CENTER?” does not 40 y
d
appear when the highway display mode is BRG: +
active. 131°
RNG: +
2. ZOOM IN/OUT is selected. Press the 0.03 mn
[ENT] key to show the zoom window.
+ 34°44.000N 135°21.000E
ZOOM
▲ OUT Cursor mark Cursor position in

latitude and longitude
20 n
m Range from own ship to cursor
▼ IN Plotter display, cursor turned on
EXIT:
[ENT]
Zoom window
9
Cursor turned off 2.5 Changing Track Plotting

The cursor is erased when there is no cursor Interval, Stopping Plotting
pad operation for about six seconds. Ship’s
To trace the ship’s track, the ship’s position is
position, speed and course appear when the
stored into the memory at an interval of
cursor is off.
distance or according to display range. For
Own ship's position distance, a shorter interval provides better
(Blinking) reconstruction of the track, but the storage
Course over ground time of the track is reduced. When the track
D2D memory becomes full, the oldest track is
erased to make room for the latest.
[ 40 n ]
m
COG: 1. Press the [MENU] key once or twice to

7° display the menu.
SOG:
k 2. Choose PLOTTER.
9.0 t
34°44.111N 135°20.555E
PLOTTER SETUP
Speed
over Own ship's position in TRACK REC : DISTANCE
ground latitude and longitude INTERVAL : 0.10 nm
BRG. REF. : MAG
Plotter display, cursor turned off MAG. VAR. : AUTO E16
WPT NAME : DSP GOTO
TTG/ETA SPD : AUTO
TRACK MEMORY USED 1%

2.3 Shifting the Display
The display can be shifted on the plotter PLOTTER SETUP menu
display. Operate the cursor pad to place the 4. The cursor is selecting TRACK REC.
cursor at an edge of the screen. The display Press the [ENT] key to show the track
shifts in the direction opposite to cursor pad recording method options.
operation.
OFF
DISTANCE
2.4 Centering Own Ship’s AUTO
Position
Track recording method options
When own ship tracks off the plotter display, 5. Choose OFF, DISTANCE or AUTO and
the own ship mark is automatically returned then press the [ENT] key.
to the screen center. You can also return it
OFF: Track is neither recorded nor
manually as follows:
plotted. This setting is useful when you do
not need to record track, for example,
1. Press the [MENU] key.
when returning to port.
2. Choose “SHIP TO CENTER?”.
DISTANCE: Track is recorded and
plotted at the distance interval set.
AUTO: Plotting and recording interval
changes with display range selected.
10
6. For AUTO or OFF, go to step 7. For

DISTANCE, enter the recording interval
as follows:
a) Press the [ENT] key.
b) Use ◄ or ► to choose digit to change.
c) Use ▲ or ▼ to change value.
d) Press the [ENT] key after setting the
recording interval.
2.6 Erasing Track

All track can be erased. Track cannot be
restored once erased, therefore be absolutely
sure you want to erase all track.
1. Press the [MENU] key once or twice to

display the menu.
2. Choose ERASE and then press the [ENT]
key to display the ERASE menu.
ERASE
WAYPOINTS/MARKS?
ROUTES?
TRACK?
RESET TRIP? (6.40nm)
RESET ODO? (6.40nm)
GPS DATA?
MENU SETTINGS?
ALL BACKUP DATA?
ERASE menu
3. Choose “TRACK?” and then press the
[ENT] key. The message shown below
appears.
ERASE TRACK.
ARE YOU SURE?

YES NO
Prompt for erasure of track

4. Press ◄ to choose YES and then press
the [ENT] key.
11
(This page intentionally left blank.)
12
3. WAYPOINTS (MARKS)
3.1 Entering Waypoints c) Press ► to move the cursor one place
and then press ▲ or ▼ to display B.
In navigation terminology a waypoint is a
d) Press ► to move the cursor one place
particular location on a voyage, whether it be
and then press ▲ or ▼ to display E.
a starting, intermediate or destination
e) Press the [ENT] key. The following
waypoint. Your unit can store 999 waypoints.
window appears.
Waypoints can be entered on the plotter
display three ways: at cursor position, at own
Comment (default: date/time)
ship’s position, and from the waypoint list.
Mark shape
Entering a waypoint with the cursor
NAME: KOBE
1. Use the cursor pad to place the cursor on 34°39.836'N MARK
the location desired for a waypoint. 135°12.059'E x
2. Press the [ENT] key. The following 10-JAN-02 10:25
window appears. TTG 02H00M ETA: 12:25
Exit? LOG RTE?
CURSOR POS. → WPT
TTG and ETA calculated according
ENTER A NEW WPT NAME. to speed set at TTG/ETA SPEED on
0 0 1_ _ _? PLOTTER menu.
(001:DEFAULT NAME) Waypoint attribute edit window

4. This window is where you can choose
QUIT: [MENU]
mark shape, enter a comment, and log
the waypoint to a route (LOG RTE?). (If
Waypoint name entry window you do not need to change mark shape or
3. The cursor is on the second line of the enter a comment, choose “Exit?” and then
display. This is where you may enter press the [ENT] key to finish. “LOG RTE?”
waypoint name, which may consist of six is discussed in chapter 4.)
alphanumeric characters. The number a) Use the cursor pad to place the cursor
shown is the youngest empty waypoint under “MARK.”
number. If you would rather have the unit b) Press the [ENT] key.
register the waypoint under that number, c) Use ▲ or ▼ to choose mark desired.
and you do not need to change mark
shape or enter a comment, press the Press .
[ENT] key twice to register the waypoint
and finish. To enter KOBE as the Note: Operating
waypoint name, for example, do the
H changes the X
following: sequence reversely.
a) Press ▲ or ▼ to display K.
+ I
b) Press ► to move the cursor one place
and then press ▲ or ▼ to display O.
Mark selection sequence
13
d) Press the [ENT] key. The cursor is 5. To change mark shape, place the cursor
selecting date/time, the default under “MARK.” Press the [ENT] key, use
comment. Press the [ENT] key. ▲ or ▼ to choose mark desired, and then
e) Enter a comment (max. 16 press the [ENT] key again.
alphanumeric characters) with the 6. The cursor is selecting date/time. To
cursor pad and then press the [ENT] change the date/time to your own
key. To create a space, choose the comment, press the [ENT] key, enter a
“blank” character. To remove all comment with the cursor pad, and then
characters which follow the cursor, press the [ENT] key again.
choose the underline.
7. Place the cursor on “Exit?.” Press the
f) The cursor is on “Exit?.” Press the [ENT] key to finish.
[ENT] key to finish.
Entering a waypoint from the waypoint
Entering a waypoint at own ship list
position
1. Press the [MARK/MOB] key momentarily
display the menu.
on any display. The following window
2. Choose WAYPOINTS.
appears.
3. Press the [ENT] key to show the waypoint
GPS POS. → MARK list options. Choose LIST. (NEAREST
displays waypoints from nearest to
NAME: 001 furthest; however, waypoints cannot be
34°39.836'N MARK entered from this display.)
135°12.059'E x
10-JAN-02 10:25D* LIST
TTG 02H00M ETA: 12:25 NEAREST
Exit? LOG RTE?
Waypoint list options
* D = Position fixed by DGPS 4. Press the [ENT] key. The WPTS/MARKS
W = Position fixed by WAAS
list appears.
Waypoint attribute edit window
2. If you want to register the waypoint under WPTS/MARKS (LIST)
the number shown, and you do not need
[NEW?] CURSOR MOB
to change mark shape or enter a START ______ ____ _ _
comment, press the [ENT] key to finish. _____ _ ______ ____ _ _
_____ _ ______ ____ _ _
3. To change name, choose NAME, press _____ _ ______ ____ _ _
the [ENT] key, enter name with the cursor _____ _ ______ ____ _ _
_____ _ ______ ____ _ _
pad, and then press the [ENT] key. The
display below appears.
WPTS/MARKS list
CREATE? CURSOR: Cursor position when
RENAME? destination is set with cursor.
Quit? MOB: Man overboard position.
START: Starting point when destination
Create, rename, quit options is selected.
4. Create is selected; press the [ENT] key.
14
5. The cursor is selecting “NEW?”; press the 3.2 Entering the MOB Mark
[ENT] key.
The MOB mark denotes man overboard
position. Only one MOB mark may be entered.
ENTER A NEW WPT NAME.
Each time the MOB mark is entered the
previous MOB mark and its position data are
0 0 4_ _ _?
written over.
(004:DEFAULT NAME) 1. Press the [MARK/MOB] key on any

Quit: [MENU] display until the following display appears.
Waypoint name entry window SAVED TO MOB.

6. Enter name (if desired) with the cursor GO TO MOB ?
pad and then press the [ENT] key.
ARE YOU SURE?
YES NO
NAME: 004
34°39.836'N* MARK
135°12.059'E* x MOB window
10-JAN-02 10:25D 2. To set MOB position as destination, press
TTG 02H00M ETA: 12:25 ◄ to choose YES and then press the
Exit? LOG RTE? [ENT] key. Then, the plotter display marks
MOB position as shown in the illustration
* Current position below.
Waypoint attribute edit window Note: Selecting “NO” saves the position
7. The cursor is selecting latitude. Press the as a waypoint.
[ENT] key. Enter latitude with the cursor
MOB position set
pad and then press the [ENT] key. as destination
8. Press the [ENT] key, enter longitude in
D2D
similar fashion as you did with latitude and
n
then press the [ENT] key. [ 40 m ]
Note: To enter position by TDs, see BRG: MOB

paragraph 7.7. 1°
9. To change mark shape, choose the mark RNG:
0.06 mn
currently shown and then press the [ENT]
key. Use ▲ or ▼ to choose mark desired 34°44.000N 135°21.000E
and then press the [ENT] key. Bearing and range to MOB position
10. To change date and time to the comment
of your choice, press the [ENT] key, enter Plotter display when MOB
comment with the cursor pad, and then is set as destination
press the [ENT] key again.
11. Place the cursor on “Exit?.” Press the
[ENT] key.
15
3.3 Displaying Waypoint 3.4 Operations on the

Name Waypoint List
You may display waypoint name as follows: Editing waypoints
Waypoint position, waypoint name, mark
shape and comment can be edited from the
display the menu.
WPTS/MARKS List.
2. Choose PLOTTER and then press the
[ENT] key.
3. Choose WPT NAME and then press the
display the menu.
[ENT] key to show the waypoint name
2. Choose WAYPOINTS and then press the
display options.
[ENT] key.
3. Choose LIST or NEAREST and then
DSP GOTO
press the [ENT] key.
DSP RTE
DSP ALL 4. Choose waypoint to edit and then press
the [ENT] key.
Note: CURSOR, MOB and START are
Waypoint name display options
automatically updated according to
4. Choose DSP GOTO, DSP RTE or DSP
destination setting or MOB setting.
ALL as appropriate and then press the
Therefore, editing these items has no
[ENT] key.
meaning.
DSP GOTO: Displays only the GOTO
waypoint name. 5. Choose NAME and then press the [ENT]
DSP RTE: Displays all waypoint names key.
when a route is set as destination. 6. Change name with the cursor pad and
DSP ALL: Displays all waypoint names. then press the [ENT] key. You are then
5. Press the [MENU] key twice to finish. asked if you want to create or rename the
waypoint, or quit (escape) the display.
CREATE?
RENAME?
Quit?
Waypoint edit options
7. Choose objective desired and then press
the [ENT] key.
8. Change position, mark shape, comment
as desired.
9. Choose “Exit?” and then press the [ENT]
key.
16
Showing nearest waypoints by 3.5 Erasing Waypoints

distance, TTG and ETA
1. Press the [MENU] key once or twice to display the menu.
open the menu. 2. Choose ERASE and then press the [ENT]
2. Choose WAYPOINTS and then press the key.
[ENT] key.
3. Choose NEAREST and then press the ERASE
[ENT] key. The display should look WAYPOINTS/MARKS?
something like the one shown below, ROUTES?
TRACK?
listing waypoints in order of distance from RESET TRIP? (6.40nm)
own vessel, from closest to furthest. RESET ODO? (6.40nm)
GPS DATA?
MENU SETTINGS?
WPTS/MARKS (NEAREST) ALL BACKUP DATA?
KOBE : 10.0 nm 344°

002 : 20.0 nm 337° ERASE menu
003 : 25.0 nm 357° 3. The cursor is selecting
004 : 40.0 nm 143°
005 : 50.0 nm 90° “WAYPOINTS/MARKS?”. Press the [ENT]
006 : 60.0 nm 200° key.
007 : 70.0 nm 320°
ERASE WPTS/MARKS
WPTS/MARKS list (NEAREST) by distance
[ALL?] CURSOR KOBE
4. To display ETA and TTG for each MOB START 001
002 003 004
waypoint, press ►. 005 006 007
______ ______ ______
______ ______ ______
WPTS/MARKS (NEAREST) ______ ______ ______
KOBE : 1H00M 12:00
002 : 2H00M 13:00
003 : 2H30M 13:30 ERASE WPTS/MARKS display
004 : 4H00M 15:00 4. Choose the waypoint you want to erase.
005 : 5H30M 16:30
006 : 6H00M 17:00 Note: You cannot erase CURSOR, MOB
007 : 7H00M 18:00
or START. To erase all waypoints, choose
ALL.
WPTS/MARKS (NEAREST) list by TTG to ETA
5. Press the [ENT] key. A screen showing
5. To return to the waypoint list by distance, position and other particulars of the
press ◄. waypoint selected appears.
menu.
NAME: KOBE
34°39.836'N MARK
135°12.059'E x
10-JAN-02 10:25D
TTG 02H00M ETA: 12:25
Quit? ERASE?
Waypoint data
6. Press ► to choose “ERASE?” and then
17
3.6 Speed for Calculating

Time-to-Go, Estimated
Time of Arrival
To calculate time-to-go and estimated time of
arrival, enter your speed as below.

open the menu.
2. Choose PLOTTER and then press the
[ENT] key.
3. ChooseTTG/ETA and then press the
[ENT] key.
4. Choose AUTO for automatic speed input
(GPS calculated speed), or MAN for
manual input.
6. For automatic speed input, go to step 7.
For manual speed input, press the [ENT]
key, enter speed with the cursor pad and
18
4. ROUTES
In many cases a trip from one place to Creating a route with the cursor
another involves several course changes,
This is probably the easiest method by which
requiring a series of waypoints which you
to create a route.
navigate to, one after another. The sequence
of waypoints leading to the ultimate
1. Use the cursor pad to place the cursor on
destination is called a route. Your unit can
position desired. (Cursor position is
automatically advance to the next waypoint
shown at the bottom of the screen.)
on a route, so you do not have to change the
2. Press the [ENT] key. The following
destination waypoint repeatedly.
window appears.
CURSOR POS. → WPT

4.1 Creating Routes
ENTER A NEW WPT NAME.
You can store up to 50 routes (numbered 01 0 0 1_ _ _?
to 50) and one LOG route, which is used to
(001:DEFAULT NAME)
temporarily store a route. A route may be
constructed four ways: by the cursor, by QUIT: [MENU]
waypoints entered from the waypoint list, by
waypoints entered from route menu, and by
Waypoint name entry window
storing current position automatically or
The cursor is on the second line of the
manually.
display. This is where you may enter
waypoint name. The number shown is the
A route may contain 30 waypoints. When 30
youngest empty waypoint number. If you
waypoints have been saved, a message
want to register the waypoint under that
informs you that you can no longer save
number, and you do not need to change
waypoints to the route. Press the [ENT] key
mark shape or enter a comment, press
to erase the message and save the route,
the [ENT] key to register the waypoint,
under the name of the first and last waypoint
and then go to step 5.
numbers used in the route.
3. If desired, change the waypoint name.
Note: Be sure to record all important routes Press the [ENT] key.
in a separate log. This unit is not a fail-safe
record keeping device. NAME: 004
WAYPOINT 34°39.836'N* MARK
WAYPOINT
(Intermediate point) 135°12.059'E* x
(Arrival point)
10-JAN-02 10:25D
WAYPOINT
(Intermediate point) TTG 02H00M ETA: 12:25
WAYPOINT Exit? LOG RTE?
(Starting point) WAYPOINT
(Intermediate point)
Sample route * Current position
Waypoint attribute edit window
19
4. ROUTES
4. If necessary, change waypoint, position,

mark shape, and comment (date and ROUTES
time). VOYAGE ROUTE: STOP
INTERVAL: TIME 00H1M
5. Choose “LOG RTE?” and then press the NO [NEW?]
[ENT] key. LOG EMPTY ROUTE
01 001 → 003
6. Repeat steps 1 through 5 to complete the __ ________________
route. __ ________________
7. When you have entered all the waypoint
positions desired, press the [MENU] key
ROUTES list
twice, choose ROUTES and then press
the [ENT] key. 4. “NEW?” is selected; press the [ENT] key.
The screen shown below appears.
ROUTES
ROUTE-01 Exit?
VOYAGE ROUTE: STOP
INTERVAL: TIME 00H10M CMNT: EMPTY ROUTE
NO [NEW?] TOTAL DISTANCE _ _ _ _ nm
®
LOG 001 003 01. _ _ _ _ _ _
02. _ _ _ _ _ _ _ _ _ _ nm _ _ _°
__ ________ ________ _ _ _ _ nm _ _ _°
__ ________ ________ 03. _ _ _ _ _ _
_ _ _ _ nm _ _ _°
__ ________ ________ 04. _ _ _ _ _ _
_ _ _ _ nm _ _ _°
05. _ _ _ _ _ _
ROUTES menu
Screen for entering route by waypoint
8. “LOG” shows the first and last waypoints
entered for the log route you are currently 5. Choose location (01, etc.) and then press
creating. Choose LOG and then press the the [ENT] key. Use ▲ or ▼ to display
[ENT] key. waypoint name. (In the example, KOBE.)
EDIT? 7. Repeat steps 5 and 6 until you have
MOVE? entered all waypoints desired.
Note: If you enter a waypoint which has
Route processing options not been registered, your screen will show
9. “MOVE?” is selected; press the [ENT] key. a message which looks something like the
The route is moved from “LOG” and is one below. Press ◄ to choose YES and
registered under the next sequential route then press the [ENT] key to create a new
number. (To edit the route before saving it, waypoint; choose NO to return to the
choose ”EDIT?”. For how to edit a route, route entry screen.
see paragraph 4.2.) NEW WPT NAME.
CREATE 008?
Creating a route from the route menu
ARE YOU SURE?
The procedure which follows describes how YES NO
to create a route from two preregistered
waypoints, KOBE and OSAKA. New waypoint creation screen
When you choose YES, the following
1. Press the [MENU] key once or twice to screen appears. Edit the waypoint as
display the menu. necessary, choose “Exit?” and then press
2. Choose ROUTES. the [ENT] key.
20
4. ROUTES
4. Choose a waypoint and then press the

NAME: 008 [ENT] key. Your screen should look
34°39.836'N MARK
something like the one below.
135°12.059'E x
10-JAN-02 11:25D
NAME: 001
TTG 02H00M ETA: 12:25 34°39.836'N MARK
Exit? 135°12.059'E x
10-JAN-02 10:25D
Waypoint attribute edit window TTG 02H00M ETA: 12.25
8. “CMNT” shows the name of the route: the Exit? LOG RTE?
names of the first and last waypoints in
the route. If you want to change the name, Waypoint attribute edit window
press ▲ to choose CMNT, press the 5. Choose “LOG RTE?” and then press the
[ENT] key, enter route name with the [ENT] key.
cursor pad and then press the [ENT] key. 6. Repeat steps 4 and 5 to complete the
9. Choose “Exit?” at the top of the screen. route.
10. Press the [ENT] key to register the route, 7. Press the [MENU] key once.
under the next sequential route number. 8. Choose ROUTES and then press the
Then, the ROUTES list shows the name [ENT] key. Your screen should now look
of the first and last waypoints used, next something like the one shown below.
to route number.
ROUTES ROUTES
VOYAGE ROUTE: STOP VOYAGE ROUTE: STOP
INTERVAL: TIME 00H10M INTERVAL: TIME 00H10M
NO [NEW?] NO [NEW?]
LOG EMPTY ROUTE LOG 004→ 006
01 001 → 003 01 001→ 003
02 KOBE → OSAKA 02 KOBE → OSAKA
__ ________________ __ ________________
ROUTES list
ROUTES list
9. Choose LOG and then press the [ENT]
Creating a route from the waypoint list key.
1. Press the [MENU] key once or twice to EDIT?

display the menu. MOVE?
2. Choose WAYPOINTS and then press the
[ENT] key. Route processing options
3. Choose LIST or NEAREST and then 10. “MOVE?” is selected; press the [ENT]
press the [ENT] key. key. The route is moved from LOG and
assigned the next sequential route
WPTS/MARKS (LIST) number.
[NEW?] 001 002 11. Press the [MENU] key twice to finish.
003 CURSOR MOB
START ______ ______
_____ _ ______ ______
_____ _ ______ ______
_____ _ ______ ______
_____ _ ______ ______
WPTS/MARKS (list)
21
4. ROUTES
Creating a track-based route 5. Choose LOG and then press the [ENT]
key.
There are two methods by which you can
create a track-based route: manual input of EDIT?
track points using the [MARK/MOB] key and MOVE?
automatic input of track points from the
ROUTES menu. A track-based route is useful Route processing options
for retracing your track. 6. “MOVE?” is selected; press the [ENT] key.
The route is moved from “LOG” and is
Creating a track-based route manually
registered under the next sequential route
This method creates a route by storing number.
position each time the [MARK/MOB] key is 7. Press the [MENU] key twice to finish.
pressed.
Creating a track-based route automatically
1. Press the [MARK/MOB] key momentarily.
This method creates a route by automatically
storing position at intervals of time or
NAME: 001
34°39.836'N MARK distance.
135°12.059'E x
10-JAN-02 10:25D 1. Press the [MENU] key once or twice to
TTG 02H00M ETA: 12:30 open the menu.
Exit? LOG RTE? 2. Choose ROUTES and then press the
[ENT] key.
Waypoint attribute edit window 3. Choose INTERVAL and then press the
2. Change name, comment and mark shape [ENT] key.
if desired. Choose “LOG RTE?” and then
press the [ENT] key. TIME
3. Repeat steps 1 and 2 when you change DISTANCE
course.
4. Choose TIME or DISTANCE (the method
4. When you have entered all the waypoint
by which position will be stored) as
positions desired, press the [MENU] key
appropriate and press the [ENT] key.
twice, choose ROUTES and then press
5. Press the [ENT] key. Use the cursor pad
the [ENT] key.
to set time or distance value and then
ROUTES press the [ENT] key.
VOYAGE ROUTE: STOP 6. Choose VOYAGE ROUTE and then press
INTERVAL: TIME 00H10M the [ENT] key.
NO [NEW?]
LOG 001→ 003
01 KOBE → OSAKA START
__ ________________ STOP
__ ________________
Voyage start options

ROUTES menu 7. Choose START and then press the [ENT]
key.
22
4. ROUTES
8. Press the [MENU] key twice to finish. 5. Place the cursor on the waypoint to
The current position is saved under the replace.
next sequential waypoint number, the 6. Press the [ENT] key to show the route edit
display shows “***SAVED!” (*** = options.
waypoint number) and a beep sounds.
Thereafter waypoints are saved at the CHANGE?
interval of time or distance set. REMOVE?
INSERT?
When 30 waypoints have been saved, a SKIP?
message informs you that you can no Quit?
longer save waypoints to the route. Press
the [ENT] key to erase the message. The
route is automatically saved to “LOG” in Route edit options
the ROUTES menu, under the name of 7. “CHANGE?” is selected; press the [ENT]
the first and last waypoint numbers used. key.
Then, open the ROUTES menu and go to
step 13. NAME: 001
34°39.836'N MARK
You can manually stop saving waypoints 135°12.059'E x
and save the route by going to step 9. 10-JAN-02 10:25D
9. After the desired number of waypoints TTG 02H00M ETA: 12:25
have been entered, press the [MENU] key Exit?
once or twice to open the menu.
10. Choose ROUTES and then press the Waypoint attribute edit screen
[ENT] key. 8. NAME is selected. Press the [ENT] key.
11. Choose VOYAGE ROUTE and then press Use the cursor pad to enter waypoint
the [ENT] key. name.
12. Choose STOP and then press the [ENT] 9. Press the [ENT] key.
key.
Note: If the name entered at step 8 does
13. Choose LOG and then press the [ENT]
not exist, the window shown below
key.
appears. Choose “CREATE?”,
14.“MOVE?” is selected; press the [ENT] key.
“RENAME?” or “Quit?” as appropriate and
The route is moved from “LOG” and is
registered under the next sequential route
number.
15. Press the [MENU] key twice to finish. CREATE?
RENAME?
Quit?
4.2 Editing Routes
Waypoint name options
Replacing waypoints in a route
10. Choose “Exit?.”
1. Press the [MENU] key once or twice to 11. Press the [ENT] key.
display the menu. 12. Press the [MENU] key twice to finish.
2. Choose ROUTES and then press the
[ENT] key.
3. Choose the route to edit.
23
4. ROUTES
Permanently deleting a waypoint from Temporarily deselecting a waypoint in

a route a route
1. Press the [MENU] key once or twice to You can temporarily deselect an unnecessary
display the menu. waypoint from a route. Using the route
2. Choose ROUTES and then press the created in the illustration at the top of the next
[ENT] key. column as an example, deselect the 2nd
3. Choose the route desired. intermediate waypoint.
[ROUTE 01] Intermediate Point 2
5. Choose the waypoint you want to delete. (WPT 002) OSAKA
(Arrival point)
7. Choose “REMOVE?.” Intermediate Point 1
8. Press the [ENT] key. (WPT 001)
9. Press the [MENU] key twice to finish. KOBE Intermediate Point 1
(Starting point) (WPT 003)
Inserting a waypoint in a route

Sample route
To insert a waypoint in a route, do the If you reconstruct the route without the 2nd
following: intermediate point it would look like the
illustration below.
1. Press the [MENU] key once or twice to WPT 002
display the menu. SKIP "002"
OSAKA
[ENT] key. WPT 001
3. Choose the route desired.
4. Press the [ENT] key. KOBE
WPT 003
5. Choose the waypoint which will come
Reconstruction of sample route above without
after the waypoint to be inserted. In the
the 2nd intermediate waypoint
illustration below, for example, if you want
to insert the waypoint between KOBE and 1. Press the [MENU] key once or twice to
001, choose 001. display the menu.
ROUTE-01 Exit? [ENT] key.
CMNT: KOBE → OSAKA 3. Choose route desired and then press the
TOTAL DISTANCE 21.0nm
01. KOBE [ENT] key.
10.2nm 180°
02. 001
9.8 nm 90° 4. Place the cursor on the waypoint to skip.
03. OSAKA
04. _ _ _ _ _ _
05. _ _ _ _ _ _ 6. Choose “SKIP?” and then press the [ENT]
key. “X” appears to the left of the waypoint
skipped as shown in the illustration below.
Route contents (Route-01)
6. Press the [ENT] key. ROUTE-01 Exit?
7. Choose “INSERT?.” CMNT: KOBE → OSAKA
TOTAL DISTANCE 21.0nm
8. Press the [ENT] key. 01. KOBE
10.2nm 180°
9. Use the cursor pad to enter waypoint. Skipped x 02. 001
9.8 nm 90°
waypoint 03. OSAKA
10. Press the [ENT] key. 04. _ _ _ _ _ _
05. _ _ _ _ _ _
Route contents (Route-01)
24
4. ROUTES
7. Press the [MENU] key twice to finish. 4.3 Erasing Routes

1. Press the [MENU] key or twice to display
To restore a waypoint to a route, choose
the menu.
“SKPoFF ?”at step 6 in this procedure, press
the [ENT] key and then press the [MENU] key
key.
twice to finish.
3. Choose “ROUTES?” and then press the
[ENT] key.
Changing route comment (name)
4. Choose the route you want delete. If you
You can change the comment (name) for a want to delete all routes, choose “ALL?.”
route as below. Up to 16 alphanumeric 5. Press the [ENT] key. You are asked if you
characters may be used. are sure to delete the route(s).
1. Press the [MENU] key or twice to display ERASE ROUTE 01 ?

the menu.
ARE YOU SURE?
[ENT] key.
YES NO
3. Choose route number and then press the
[ENT] key.
Erase route options
4. Choose CMNT and then press the [ENT]
6. Choose YES and then press the [ENT]
key.
key.
5. Enter comment with the cursor pad and
25
4. ROUTES
26
5. DESTINATION
Destination can be set four ways: by cursor, A dashed line connects own ship and the
by waypoint, by route, and by MOB position. destination, which is marked with “CURSOR”
Previous destination is cancelled whenever a and an “X,” as shown in the illustration below.
destination is newly set. CURSOR
x
5.1 Setting Destination by

Cursor
Destination set by cursor
1. Press the [GOTO] key to display the
GOTO options window.
GOTO 5.2 Setting Destination by

WPT-LIST? _ _ _ _ _ _ ? Waypoint
WPT-NEAR? OFF??
1. Press the [GOTO] key.
ROUTE?
CURSOR? SETUP? 2. Choose “WPT-LIST?” or “WPT-NEAR?”.
3. Press the [ENT] key. The SELECT GOTO
GOTO options WPT list appears.
2. Choose “CURSOR?.” SELECT GOTO WPT
3. Press the [ENT] key. The plotter display
appears, with “?” shown to the right of the [NEW?] 001 002
003 004 005
cursor. 006 007 008
CURSOR KOBE MOB
Cursor appears with "?". OSAKA START ______
______ ______ ______
______ ______ ______
2D
n WPT-LIST
[ 40 m ] ?
+GOTO?
BRG: +
SELECT GOTO WPT
72° START : 2.97 nm 68°
RNG: + OSAKA : 1.90 nm 335°
54.5 mn 006 : 3.53 nm 15°
005 : 4.79 nm 11°
34°44.000N 135°21.000E 004 : 4.86 nm 15°
008 : 5.21 nm 345°
CURSOR : 6.41 nm 356°
Cursor appearance
when setting destination by cursor WPT-NEAR
4. Use the cursor pad to place the cursor on
the location desired for destination. SELECT GOTO WPT screens
5. Press the [ENT] key. 4. Choose a waypoint.
Own ship’s position becomes the starting

point and a dashed line runs between it and
the waypoint selected, which is shown in
reverse video.
27
5. DESTINATION
5.3 Setting Route as 5.4 Setting User Waypoint as

Destination Destination
1. Press the [GOTO] key. You may place a desired waypoint in the
2. Choose “ROUTE?”. GOTO options window and use it to set
3. Press the [ENT] key. destination.
SELECT GOTO ROUTE Choosing user waypoint

NO [NEW?]
LOG EMPTY ROUTE
01 ®
017 021 2. Choose “SETUP?” and then press the
02 ®
OSAKA KOBE [ENT] key.
03 ®
EIMI KIMI
04 BOSTON
SELECT USER WPT
[NEW?] 001 002
003 004 005
GOTO ROUTE list 006 007 008
4. Choose a route. CURSOR KOBE MOB
OSAKA START ______
5. Press the [ENT] key. The following ______ ______ ______
options window appears. ______ ______ ______
FORWARD?
REVERSE? SELECT USER WPT list
3. Choose waypoint desired and then press
Route following direction options the [ENT] key. The GOTO window
6. Choose “FORWARD?” or “REVERSE?”, appears, showing the waypoint selected
the order in which to traverse the route as below.
waypoints, and then press the [ENT] key. GOTO
[ROUTE 01] Intermediate Point 2 OSAKA WPT-LIST? 001 Location of
(WPT 002) (Arrival point) WPT-NEAR? OFF?? user waypoint
Intermediate Point 1 (Example: 001)
(WPT 001)
ROUTE?
CURSOR? SETUP?
FORWARD REVERSE
KOBE GOTO options
(Starting point) Intermediate Point 1
(WPT 003) 4. Choose user waypoint and then press the
Meaning of forward and reverse [ENT] key.
Current position becomes the starting point. A
dashed line runs between the starting point A dashed line connects own ship and the
and all route waypoints. Next destination waypoint selected, which is shown in reverse
waypoint is shown in reverse video. video.
The destination waypoint is automatically

switched when the boat enters the arrival 5.5 Canceling Destination
alarm range or the boat passes an imaginary
You can cancel destination as follows:
perpendicular line passing through the center
of the destination waypoint. For how to set
the arrival alarm, see paragraph 6.1.
2. Choose “OFF?”.
28
6. ALARMS
There are eight alarm conditions which 6.1 Arrival Alarm, Anchor
generate both audio and visual alarms: Watch Alarm
Arrival alarm, Anchor watch alarm, XTE
(Cross-Track Error) alarm, Speed alarm, You may activate the arrival alarm or the
WAAS/DGPS alarm, Time alarm, Trip alarm anchor watch alarm; they cannot be activated
and Odometer alarm. together.
When an alarm setting is violated, the buzzer Arrival alarm

sounds and the name of the offending alarm The arrival alarm informs you that own ship is
and the alarm icon appear on the display. approaching a destination waypoint. The area
that defines an arrival zone is that of a circle
You can silence the buzzer and remove the which you approach from the outside of the
alarm name indication by pressing any key. circle. The alarm will be released if own ship
The alarm icon remains on the screen until enters the circle.
the reason for the alarm is cleared.
Alarm
In some instances, multiple alarms may have setting
been violated. You can see which alarm(s) is Own ship's
sounding by displaying the message board. position
The keying sequence is [MENU] (once or
twice), MESSAGE, [ENT]. The message : Alarm released Destination
waypoint
board is discussed in paragraph 8.2
“Displaying the Message Board.” How the arrival alarm works
To disable an alarm, choose OFF as its open the menu.
option, press the [ENT] key and then press 2. Choose ALARMS.
the [MENU] key twice. 3. Press the [ENT] key to show the ALARMS
menu.
Alarm message
ALARMS
2D XTE ALARM! ! BUZZER : LONG
ARV/ANC : ARV 0.30 nm
[ 40 n ]
m XTE : OFF 0.50 nm
SPEED : OFF 12.0 kt
COG: Alarm WAAS/DGPS : OFF
82° icon TIME : OFF 00:00
TRIP : OFF 0 nm
SOG:
k ODOMETER : OFF 0 nm
9.0 t
34°44.000N 135°21.000E ALARMS menu
Location of alarm message and alarm icon
29
6. ALARMS
4. Choose ARV/ANC and then press the 6. Press the [ENT] key. Enter the alarm
[ENT] key. range (0.01-99.99 nm) with the cursor
pad.
OFF 7. Press the [ENT] key.
ARV 8. Press the [MENU] key twice to finish.
ANC
When own ship drifts more than the range set
Arrival/anchor watch options here, the buzzer sounds and the message
5. Choose ARV and then press the [ENT] ANC ALARM! and the alarm icon appear.
key.
6. Press the [ENT] key. Enter the alarm
range (0.0-99.99 nm) with the cursor pad. 6.2 XTE (Cross Track Error)
7. Press the [ENT] key. Alarm
The XTE alarm warns you when own ship is
off its intended course.
When own ship nears the GOTO waypoint by
the range set here, the buzzer sounds and
the message ARV ALARM! appears.
Alarm Destination
Anchor watch alarm Own ship's
setting waypoint
position
The anchor watch alarm sounds to warn you
that own ship is moving when it should be at
rest.
: Alarm released
Own ship's
Alarm position How the XTE alarm works
setting 1. Press the [MENU] key once or twice to
open the menu.
2. Choose ALARMS.
4. Choose XTE and then press the [ENT]
Destination
waypoint : Alarm released key.
5. Choose ON and then press the [ENT] key.
How the anchor watch alarm works 6. Press the [ENT] key. Enter alarm range
Before setting the anchor watch alarm, set (0.0-99.99 nm) with the cursor pad.
current position as destination waypoint, 7. Press the [ENT] key.
referring to paragraph 5.2. 8. Press the [MENU] key twice to finish.
1. Press the [MENU] key once or twice to When own ship strays from the intended track
open the menu. by the range set here, the buzzer sounds and
2. Choose ALARMS. message XTE ALARM! and the alarm icon
3. Press the [ENT] key. appear.
4. Choose ARV/ANC and then press the
[ENT] key.
5. Choose ANC and then press the [ENT]
key.
30
6. ALARMS
6.3 Speed Alarm When the DGPS/WAAS signal is lost, the

buzzer sounds and a message (see table
The speed alarm provides visual and aural
below) and the alarm icon appear. Further,
alerts when the ship’s speed is higher (or
the default position is shown.
lower) than the alarm range set.
WAAS/DGPS mode and alarm message
open the menu. MODE on
Alarm condition, alarm
2. Choose ALARMS. WAAS/DGPS
message
3. Press the [ENT] key. menu
Alarms released when
4. Choose SPEED and then press the [ENT]
receiver status changes from
key.
W2D or W3D to 2D or 3D.
5. Choose LOW or HIGH as appropriate and WAAS
“WAAS ERROR!” and the
then press the [ENT] key. alarm icon appear when this
LOW: Alarm sounds when speed is lower occurs.
than speed set. Alarms released when
HIGH: Alarm sounds when speed is receiver status changes from
higher than speed set. INT BEACON, D2D or D3D to 2D or 3D.
EXT BEACON “DGPS ERROR!” and the
6. Press the [ENT] key. Enter speed
alarm icon appear when this
(0.0-999.9 kt) with the cursor pad.
occurs.
Alarms released when
8. Press the [MENU] key twice to finish. receiver status changes from
D2D, D3D, W2D or W3D to
When the speed alarm setting is violated, the AUTO
2D or 3D. “WAAS/DGPS
buzzer sounds and the message SPD ERROR!” and the alarm icon
ALARM! and the alarm icon appear. appear when this occurs.
6.5 Time Alarm

6.4 WAAS/DGPS Alarm The time alarm works like an alarm clock,
releasing audio and visual alarms when the
This alarm alerts you by aural and visual time entered has come.
alarms when the WAAS/DGPS signal is lost.
Note that ON cannot be selected if “MODE” in 1. Press the [MENU] key once or twice to
the WAAS/DGPS menu is set to GPS. open the menu.
2. Choose ALARMS.
1. Press the [MENU] key once or twice to 3. Press the [ENT] key.
open the menu. 4. Choose TIME and then press the [ENT]
2. Choose ALARMS. key.
3. Press the [ENT] key. 5. Choose ON and then press the [ENT] key.
4. Choose WAAS/DGPS and then press the 6. Press the [ENT] key.
[ENT] key. 7. Enter time desired with the cursor pad.
5. Choose ON. 8. Press the [ENT] key.
6. Press the [ENT] key. 9. Press the [MENU] key twice to finish.
When the time entered has come, the buzzer
sounds and the message TIME ALARM! and
the alarm icon appear.
31
6. ALARMS
6.6 Trip Alarm 6.8 Buzzer Type Selection

This alarm alerts you by aural and visual The buzzer sounds whenever an alarm
alarms when your boat has traveled a setting is violated. You can choose the type
distance greater than the trip alarm distance. of buzzer to use as follows:
1. Press the [MENU] key once or twice to 1. Press the [MENU] key once or twice to
open the menu. open the menu.
2. Choose ALARMS. 2. Choose ALARMS.
3. Press the [ENT] key. 3. Press the [ENT] key.
4. Choose TRIP and then press the [ENT] 4. Choose BUZZER and then press the
key. [ENT] key.
6. Press the [ENT] key. Enter distance SHORT
desired (001-999 nm) with the cursor pad. LONG
7. Press the [ENT] key. CONSTANT
Buzzer sound options
When the boat has traveled further than the 5. Choose buzzer type desired and then
preset trip distance, the buzzer sounds and press the [ENT] key.
the message TRIP ALARM! and the alarm SHORT: Two short beeps
icon appear. LONG: Three long beeps
CONSTANT: Continuous beeps
6.7 Odometer Alarm
This alarm alerts you by aural and visual
alarms when your boat has traveled the total
distance you set.

open the menu.
2. Choose ALARMS.
4. Choose ODOMETER and then press the
[ENT] key.
6. Press the [ENT] key. Enter distance
desired (001-999 nm) with the cursor pad.
When the boat has traveled further than the

preset trip distance, the buzzer sounds and
the message ODOMETER ALARM! and the
alarm icon appear.
32
7. OTHER FUNCTIONS
7.1 Calculating Range, 10. Press the [ENT] key. Enter speed with the
Bearing, TTG and ETA cursor pad and then press the [ENT] key.
Range and bearing between two The illustration below shows what the
waypoints display might look like using waypoints
1. Press the [MENU] key once or twice to KOBE and OSAKA as the FROM and TO
open the menu. waypoints, respectively.
2. Choose CALCULATE and then press the Time-to-Go
[ENT] key. Estimated Time of Arrival
CALCULATION CALCULATION
MODE : WAYPOINTS MODE : WAYPOINTS

FROM : ______ FROM : KOBE
TO : ______ TO : OSAKA
SPD : AUTO SPD : AUTO
TTG: _ _ H _ _ M ETA: _ _ : _ _ TTG: 1H39M ETA: 5:57

RNG: _ . _ _ nm BRG: _ _ _ ° RNG: 9.06 nm BRG: 80 °
CALCULATION menu
Range Bearing
3. The cursor is selecting MODE. Press the Typical range and bearing calculation
[ENT] key. between two waypoints
WAYPOINTS
ROUTE
Range, TTG and ETA between first and
Range and bearing calculation options final waypoints of a route
4. Choose WAYPOINTS and then press the You can easily find the range, TTG and ETA
[ENT] key. between the first and final waypoints of a
5. Press the [ENT] key. route as follows:
6. Enter the FROM waypoint and then press
the [ENT] key. 1. Press the [MENU] key once or twice to
7. Press the [ENT] key, enter the TO open the menu.
waypoint and then press the [ENT] key. 2. Choose CALCULATE and then press the
8. Press the [ENT] key to display the speed [ENT] key.
input options. 3. Press the [ENT] key.
4. Choose ROUTE and then press the [ENT]
AUTO key.
MAN 5. Press the [ENT] key.
6. Choose route number from the route list
Speed input options with the cursor pad.
9. Choose AUTO or MAN and then press the 7. Press the [ENT] key to open the speed
[ENT] key. AUTO uses ship’s average input options window.
speed; MAN is for manual entry of speed. 8. Choose AUTO or MAN. AUTO uses ship’s
For AUTO, see the illustration after step average speed; MAN is for manual entry
10 for sample range and bearing of speed.
calculation. For MAN, go to step 10.
33
7. OTHER FUNCTIONS
9. Press the [ENT] key. If you selected 4. Choose appropriate mode referring to the
AUTO no further operation is necessary. descriptions below. Press the [ENT] key.
See the illustration below for a calculation WAAS: Position fix by WAAS
example. For MAN, press the [ENT] key, AUTO: Position fix in priority order of
enter speed with the cursor pad and then DGPS, WAAS, and GPS.
press the [ENT] key. 5. Press the [ENT] key.
The illustration below shows what the 6. WAAS SEARCH is selected; press the
display might look like using Route-01 as [ENT] key.
an example.
Time-to-Go AUTO
Estimated Time of Arrival MANUAL
CALCULATION
WAAS search options
MODE : ROUTE
NO. : 01 (WPTS: 4) 7. Choose AUTO for automatic search or
KOBE → OSAKA
SPD : AUTO
MANUAL for manual search and then
press the [ENT] key. For MANUAL, press
TTG: 1H55M
RNG: 11.25 nm
ETA: 07:17
BRG: _ _ _ °
the [ENT] key, enter appropriate WAAS
satellite number, referring to the
illustration below and then press the
Range
[ENT] key.
Typical TTG, ETA, range calculation for route
AUTO mode and GEO satellite
(as of April 2002)
7.2 WAAS Setup Provider GEO Satellite Longitude

1. Press the [MENU] key once or twice to POR (134) 178°E
WAAS
open the menu. AOR-W (122) 54°W
2. Choose WAAS/DGPS and then press the
AOR-E (120) 15.5°W
[ENT] key. EGNOS
IOR (131) 64.5°E
WAAS/DGPS SETUP 118°W 34.75°W 24.5°E 121.25°E
MODE : AUTO 2° 2° 2° 2°
WAAS SEARCH: AUTO 120
CORRECTIONS DATA SET: 02 122 120 131 134
DGPS STATION: AUTO
AOR-W AOR-E IOR POR
RATE : 200BPS
FREQ : 310.0 kHz 54°W 15.5°W 64.5°W 178°E
STATION : GOOD DATA: GOOD
SIG.S: 55.2 dB SNR: 22.0dB
WAAS/DGPS SETUP menu One-degree threshold
3. The cursor is selecting MODE; press the Longitude Range Satellite

[ENT] key. 120.25°E to 117°W 134
119°W to 33.75°W 122
GPS GPS position fixing 35.75°W to 25.5°E 120
WAAS 23.5°E to 122.25°E 131
INT BEACON DGPS position fixing
EXT BEACON GEO satellite and coverage area
AUTO
WAAS/DGPS mode options
34
7. OTHER FUNCTIONS
8. The cursor is now selecting INT BEACON: Position fix by internal

CORRECTIONS DATA SET; press the DGPS beacon receiver (GP-37 only,
[ENT] key. cannot be selected on GP-32)
CORRECTIONS DATA SET determines EXT BEACON: Position fix by external
how to use the WAAS signal, currently in DGPS beacon receiver (GP-32)
the test mode. Use the default setting AUTO: Position fix by DGPS, WAAS and
(02) until the WAAS system becomes GPS, in order of availability.
operational, then change the setting to Note: When connecting FURUNO
“00”. external DGPS beacon receiver GR-80 to
9. Press the [ENT] key. the GP-32, turn the GR-80’s remote
10. Press the [MENU] key twice to close the function on to set up the beacon receiver
menu. with data set on the GP-32.
5. DGPS STATION is selected; press the
[ENT] key.
7.3 DGPS setup 6. Choose DGPS beacon station selection
1. Press the [MENU] key once or twice to method: AUTO, MANUAL or LIST.
open the menu. AUTO: Automatically searches for best of
2. Choose WAAS/DGPS. five nearest DGPS beacon station. It first
searches DGPS beacon stations from
WAAS/DGPS SETUP
closest to furthest. If unsuccessful it
MODE : GPS
WAAS SEARCH: AUTO 120 searches stations by signal strength. This
CORRECTIONS DATA SET: 02 procedure is repeated until a suitable
DGPS STATION: AUTO
RATE : 200BPS station is found.
FREQ : 310.0 kHz MANUAL: Manually enter DGPS beacon
STATION : ---* DATA: ---*
SIG.S: 00.0 dB * SNR: 02.0dB* station specifications at RATE and FREQ,
* = See note below. referring to a DGPS beacon station list.
LIST: Lists five of the closest DGPS
WAAS/DGPS SETUP menu
beacon stations, including
DGPS Data user-programmed stations.
7. Press the [ENT] key. If you selected
STATION: Shows GOOD or NG.
AUTO no further operation is required; go
DATA: Shows GOOD or NG. to step 8. If you selected MANUAL or LIST,
SIG. S: Signal Strength. A figure do one of the following and then go to
between 0 and 99 is shown. The higher step 8.
the figure the stronger the beacon signal.
MANUAL
SNR: Signal to Noise Ratio. A figure
between 1and 22 is shown. A figure under a) The cursor is selecting RATE. Press
18 means position will be inaccurate. the [ENT] key.
When your boat is in the service area of a
beacon station, SNR should be 21 or 22. b) Choose the transmission rate of the
If not, the problem may lie with the DGPS beacon station to be used,
grounding, radar interference or generator
noise on own boat. among 50, 100 or 200 bps. Press the
[ENT] key.
3. Press the [ENT] key to show the mode c) The cursor is selecting FREQ. Press
options window. the [ENT] key.
4. Choose one of the following and then
35
7. OTHER FUNCTIONS
d) Use the cursor pad to enter the STATION (USER)

transmission frequency of the DGPS [EXIT] [NEW?] [CLR?]
beacon station to be used and then 01 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
02 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
press the [ENT] key. 03 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
04 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
LIST 05 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
06 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
a) The following display appears after
pressing the [ENT] key at step 6. DGPS STATION (USER) list
6. Choose “NEW?” and then press the [ENT]
STATION (NEAREST)
key.
[EXIT] [USER]
310.0 29.1 nm 92°
287.0 56.7 nm 134° NEW USER CHANNEL
292.0 160 nm 320°
321.0 234 nm 134° STATION (USER)
302.0 426 nm 121° *
FREQ : 310.0kHz
RATE : 200BPS
LAT : 37°59'N
Tx frequency of "*" denotes LON : 123°00'W
beacon station user channel.
Range (ref. only) and bearing from EXIT? SAVE?
ship to beacon station
DGPS beacon station list
b) Use the cursor pad to choose station NEW USER CHANNEL (DGPS) set up menu
desired. 7. Press the [ENT] key, enter frequency of
c) Press the [ENT] key. the station, and then press the [ENT] key.
8. Press the [MENU] key twice to finish. 8. Press the [ENT] key, enter baud rate of
the station, and then press the [ENT] key.
Programming DGPS user channels 9. Press the [ENT] key, enter latitude of the
(stations) station, and then press the [ENT] key.
10 Press the [ENT] key, enter longitude of
The user may program 20 DGPS beacon the station, and then press the [ENT] key.
stations from which to use in DGPS beacon 11. Choose “SAVE?” and then press the
station selection. Whenever a new station is [ENT] key.
constructed you can add it to the list. 12. Press the [MENU] key twice to finish.
1. Press the [MENU] key twice to open the Editing DGPS user channels
menu.
2. Choose DGPS/WAAS and then press the 1. Press the [MENU] key twice to open the
[ENT] key. menu.
3. Choose DGPS STATION and then press 2. Choose WAAS/DGPS and then press the
the [ENT] key. [ENT] key.
4. Choose LIST and then press the [ENT] 3. Choose DGPS STATION and then press
key. the [ENT] key.
5. Choose USER and then press the [ENT] 4. Choose LIST and then press the [ENT]
key. key.
5. Choose USER and then press the [ENT]
key.
36
7. OTHER FUNCTIONS
6. Choose a station from the list and then Erasing individual user channels
press the [ENT] key. The display looks
1. Press the [MENU] key twice to open the
something like the one below.
menu.
2. Choose DGPS/WAAS and then press the
FREQ : 310.0kHz
RATE : 200BPS [ENT] key.
LAT : 37°59'N 3. Choose DGPS STATION and then press
LON : 123°00'W
the [ENT] key.
EXIT? SAVE? ERASE? 4. Choose LIST and then press the [ENT]
key.
5. Choose USER and then press the [ENT]
key.
Screen for entering DGPS station data 6. Choose a channel from the list and then
7. Choose item, press the [ENT] key, edit press the [ENT] key.
data, and then press the [ENT] key. 7. Choose “ERASE?”.
8. Choose “SAVE?” and then press the 8. Choose YES and then press the [ENT]
[ENT] key. key.
9. Press the [MENU] key twice to finish. 9. Press the [MENU] key twice to finish.
Erasing all user channels

7.4 Bearing Reference
1. Press the [MENU] key twice to open the
menu. Ship's course and bearing to a waypoint may
2. Choose DGPS/WAAS and then press the be displayed in true or magnetic bearing.
[ENT] key. Magnetic bearing is true bearing plus (or
3. Choose DGPS STATION and then press minus) earth’s magnetic deviation. Use the
the [ENT] key. bearing reference in accordance with the
4. Choose LIST and then press the [ENT] compass interfaced: magnetic for magnetic
key. compass, true for gyrocompass. The default
5. Choose USER and then press the [ENT] setting displays magnetic bearings.
key.
6. Choose “CLR?” and then press the [ENT] 1. Press the [MENU] key once or twice to
key. The following message appears. open the menu.
2. Choose PLOTTER.
ERASE ALL ? 3. Press the [ENT] key.
4. Choose BRG. REF.
ARE YOU SURE ?
YES NO
MAG
TRUE
DGPS channel erase options
Bearing reference options
the [ENT] key.
6. Choose MAG or TRUE as appropriate.
37
7. OTHER FUNCTIONS
7.5 Magnetic Variation 1. Press the [MENU] key once or twice to

open the menu.
The location of the magnetic north pole is
different from the geographical north pole.
[ENT] key.
This causes a difference between the true
and magnetic north direction. This difference
SYSTEM SETUP
is called magnetic variation, and varies with
LANGUAGE : ENGLISH
respect to the observation point on earth. DATUM : WGS84
Your unit is preprogrammed with all the UNITS : nm, kt
TIME DIFF : +00 : 00
earth's magnetic variation. However, you may TIME DISP : 24HOUR
wish to enter variation manually to refine TEST?
SIMULATOR?
accuracy. Set “BRG REF” on the PLOTTER EXCHANGE BATTERY?
is set to “MAG” to use magnetic variation.
SYSTEM SETUP menu
1. Press the [MENU] key once or twice to 3. Choose DATUM and then press the [ENT]
open the menu. key.
2. Choose PLOTTER and then press the 4. Choose WGS84 (GPS standard), WGS72
[ENT] key. or OTHER as appropriate and then press
3. Choose MAG. VAR. the [ENT] key.
4. Press the [ENT] key. 5. If you selected WGS84 or WGS72, go to
5. Choose AUTO or MAN as appropriate step 6. For OTHER, do the following:
and then press the [ENT] key. For a) Press the [ENT] key.
automatic magnetic variation, current b) Use the cursor pad to enter chart
magnetic variation appears to the right of number, referring to the geodetic chart
AUTO. list on page AP-3.
6. If you selected AUTO, no further c) Press the [ENT] key.
operation is necessary; go to step 7. For 6. Press the [MENU] key twice to finish.
MAN, press the [ENT] key and enter
magnetic variation as follows:
a) If necessary, change coordinate from 7.7 Units of Measurement
east to west or vice versa by pressing
▲ or ▼. Distance/speed can be displayed in nautical
b) Press ► to shift cursor, use ▲ or ▼ to miles/knots, kilometers/kilometers per hour,
set value, referring to a nautical chart. or statute miles/miles per hour.
c) Press the [ENT] key.
7. Press the [MENU] key twice to finish. 1. Press the [MENU] key once or twice to
open the menu.
7.6 Geodetic Chart System [ENT] key.
3. Choose UNITS.
Your unit is preprogrammed to recognize 4. Press the [ENT] key.
most of the major chart systems of the world. 5. Choose combination desired; nm, kt; km,
Although the WGS-84 system, the GPS km/h; sm, mph.
standard, is now widely used other categories 6. Press the [ENT] key.
of charts still exist. Choose the chart system 7. Press the [MENU] key twice to finish.
used, not the area where your boat is sailing.
The default chart system is WGS-84.
38
7. OTHER FUNCTIONS
7.8 Position Display Format d) If necessary enter TD offsets at ∆TD1

and ∆TD2 to refine position accuracy.
Position may shown in latitude and longitude
or TDs (Loran C or Decca) as follows. Decca For Decca TD:
and Loran C chain data is preprogrammed. a) Choose DECCA and then press the
[ENT] key.
b) Use the cursor pad to choose
open the menu.
appropriate Decca chain number and
2. Choose TD SETUP and then press the
lane pair (R, Red, G, Green, P, Purple),
[ENT] key.
referring to the Decca chain list on
page AP-5.
TD SETUP
DISPLAY : XX.XXX'
LORAN C : 7980: 23-43 d) If necessary enter TD offsets at ∆TD1
∆TD1 : +00 . 0 and ∆TD2 to refine position accuracy.
∆TD2 : +00 . 0
DECCA : 25: G-P 7. Press the [MENU] key twice to finish.
∆TD1 : +00 . 0
∆TD2 : +00 . 0
7.9 Time Difference (using

TD SETUP menu
local time), Time Format
3. The cursor is on the first line. Press the
[ENT] key. GPS uses UTC time. If you would rather use
local time, enter the time difference (range:
XX.XXX' -13:30 to +13:30) between it and UTC time.
XX'XX.X"
LC TD
DE TD You may display the time in 12 or 24 hour
format.
Position display options
4. Choose desired position format. 1. Press the [MENU] key once or twice to
open the menu.
XX.XXX’: Shows L/L position with no
seconds.
[ENT] key.
XX’XX.X’: Displays L/L position with
seconds. 3. Press ▼ to choose TIME DIFF and then
LC TD: Loran C TDs press the [ENT] key.
DE TE: Decca TDs 4. Press ▲ or ▼ to display “+” or “-“ as
5. Press the [ENT] key. If you selected a appropriate.
latitude and longitude format, go to step 7. 5. Enter time difference with the cursor pad.
6. For Loran C or Decca, do one of the 6. Press the [ENT] key.
following and then go to step 7. 7. The cursor is selecting TIME DISP. Press
the [ENT] key.
For Loran C TD:
8. Choose 12 HOUR or 24 HOUR as
a) The cursor is on LORAN C. Press the appropriate and then press the [ENT] key.
[ENT] key. 9. Press the [MENU] key twice to finish.
b) Use the cursor pad to choose
appropriate GRI code and secondary
codes, referring to the Loran C chain
list on page AP-4.
39
7. OTHER FUNCTIONS
7.10 GPS Setup SMOOTH S/C (Smoothing speed/course)
The GPS SETUP menu smoothes position During position fixing, ship’s velocity (speed
and course, averages speed, applies position and course) is directly measured by receiving
offset, and deactivates unhealthy satellites. GPS satellite signals. The raw velocity data
may changes randomly depending on
1. Press the [MENU] key once or twice to receiving conditions and other factors. You
open the menu. can reduce this random variation by
2. Choose GPS SETUP and then press the increasing the smoothing. Like with latitude
[ENT] key. and longitude smoothing, the higher the
speed and course smoothing the more
GPS SETUP smoothed the raw data. If the setting is too
SMOOTH POS : 0SEC high, however, the response to speed and
SMOOTH S/C : 5SEC course change slows. The setting range is
AVR. SPEED : 60SEC
LAT OFFSET : 0.000'N
from 0 (no smoothing) to 9999 seconds.
LON OFFSET : 0.000'E
DISABLE SV : __ __ __ AVR. SPEED (Speed averaging)
FIX MODE : 2/3D
Calculation of ETA and TTG, etc. is based on
average ship's speed over a given period. If
GPS SETUP menu
the period is too long or too short, calculation
3. Choose item and then press the [ENT]
error will result. Change this setting if
key.
calculation error occurs. The default setting is
4. Change setting with the cursor pad and
60 seconds. The setting range is from 0 (no
averaging) to 9999 seconds.
LAT/LON OFFSET (L/L position offset)
GPS SETUP menu description
You may apply an offset to latitude and
SMOOTH POS (Smoothing position)
longitude position generated by the GPS
When the DOP (Dilution of Precision, the receiver, to increase position accuracy.
index for position-fixing accuracy) or receiving
condition is unfavorable, the GPS fix may DISABLE SV
change greatly, even if the vessel is dead in
Every GPS satellite is broadcasting abnormal
water. This change can be reduced by
satellite number(s) in its Almanac, which
smoothing the raw GPS fixes. The setting
contains general orbital data about all GPS
range is from 0 (no smoothing) to 999
satellites. Using this information, the GPS
seconds. The higher the setting the more
receiver automatically eliminates any
smoothed the raw data, however too high a
malfunctioning satellite from the GPS satellite
setting slows response time to change in
schedule. However, the Almanac sometimes
latitude and longitude. This is especially
may not contain this information. You can
noticeable at high ship’s speeds. “0” is the
disable an inoperative satellite manually.
normal setting; increase the setting if the
Enter satellite number in two digits and then
GPS fix changes greatly.
press the [ENT] key. To restore a satellite
enter “00”.
40
7. OTHER FUNCTIONS
DISABLE GEO 3. Choose 1 or 2 and then press the [ENT]

key.
Like GPS satellites, the GPS receiver
automatically eliminates any malfunctioning
OFF
WAAS satellite. To disable a WAAS satellite DIGITAL
manually, enter three-digit satellite number SPEEDOMETER
with the cursor pad and then press the [ENT]
key. To restore a satellite, enter “000”.
User display type options
FIX MODE 4. Choose DIGITAL and then press the

[ENT] key.
Chooses position fixing method; 2D or 2/3D. 5. The cursor is selecting the square at the
2D requires three satellites in view of the right side of the screen. Press the [ENT]
GPS receiver; 2/3D requires three or four key.
satellites in view of the GPS receiver,
whichever is available. When the 2D mode is : 1 indication
selected, enter the antenna height above the : 2 indications
: 3 indications
waterline, to obtain accurate position data.
: 4 indications
The default setting is 5 m.
User display screen division options
6. Choose the screen division desired, that
7.11 User Display Setup is, the number of data to display, and then
The user displays, which appear when the press the [ENT] key. The display now
[DISP] key is pressed several times, provide looks something like the one shown
user-customized digital data and a below.
speedometer.
USER DISPLAY
Digital data A: POWER

B: TRIP A C *
The user may choose 1-4 items of navigation C: SOG B D
D: COG
data to display on the digital display.

open the menu. * = Changes according to selection at step 6.
2. Choose USER DISP and then press the A A
[ENT] key. A
B B C
USER DISPLAY
USER DISPLAY menu,
default digital display settings
1: DIGITAL 7. “A” is selected. Press the [ENT] key.
2: SPEEDOMETER
NONE ODO TRIP
TIME POSN POWER
SOG COG WPT
XTE TTG ETA
USER DISPLAY menu Digital data options
41
7. OTHER FUNCTIONS
8. Use the cursor pad to choose data 9. Enter scale interval: Use ◄ or ► to
desired and then press the [ENT] key. choose location and ▲ or ▼ to enter
NONE: No display value. The setting range is 1 to 99.
ODO: Odometer distance 10. Press the [ENT] key.
TRIP: Trip distance
TIME: Time and date
POSN: Position menu.
POWER: Power source voltage
SOG: Speed over ground
COG: Course over ground 7.12 Resetting Trip and
WPT: Rng and brg to waypoint
XTE: Cross-track error Odometer Distances
TTG: Time to go (to destination) 1. Press the [MENU] key once or twice to
ETA: Estimated time of arrival
open the menu.
(at destination)
9. Control returns to the User display setup,
key.
with “B” selected. Depending on the
3. Choose “RESET TRIP?” (or “RESET
selection made at step 5, set other
ODO?”) and then press the [ENT] key.
indications similar to how you did with “A”.
One of following displays appears.
Speedometer display RESET

TRIP METER?
1. Press the [MENU] key once or twice to ARE YOU SURE?
open the menu. YES NO
2. Choose USER DISP and then press the
[ENT] key.
3. Choose 1 or 2 and then press the [ENT]
key. RESET
4. Choose SPEEDOMETER and then press ODOMETER?
the [ENT] key. ARE YOU SURE?
YES NO
SPEEDOMETER
Reset trip meter, odometer options

START FROM: + 0
INTERVAL : 10
the [ENT] key to reset distance to zero.
0 10 20 30 40
Start point Interval
Speedometer menu
5. The cursor is selecting START FROM.
Press the [ENT] key.
6. Enter starting speed: Use ◄ or ► to
select location and ▲ or ▼ to enter value
and switch from plus to minus and vice
versa. The setting range is -99 to +99.
7. Press the [ENT] key, and the cursor shifts
to INTERVAL.
42
7. OTHER FUNCTIONS
7.13 Uploading, Downloading Setting for communication software on

Waypoint, Route Data PC
Baud Rate: 4800 bps
Waypoint and route data may be downloaded
Character Length: 8 bit
to a PC or uploaded from a PC to your unit.
Stop Bit: 1 bit
Parity: None
Wiring
X Control: XON/OFF
Your equipment provides a wiring diagram
which shows how to connect to a PC using a Downloading/Uploading between PC
DSUB 9-pin connector (EIA-574). You may and GP-37/GP-32
display it as follows.
Waypoint data and route data can be
downloaded/uploaded between a personal
computer and the GP-37/GP-32.
open the menu.
2. Choose I/O SETUP and then press the
Note 1: There are two kinds of data for route
[ENT] key.
data: route data and route comment data.
3. Choose WIRING INFO and then press the
Note 2: No position fix is available during
[ENT] key to display the wiring diagram.
uploading or downloading.
WIRING INFO
Downloading data to a PC
1TD-H WHITE PC/AT DSUB-9
2TD-C/SG BLUE 5 GND 1. Press the [MENU] key once or twice to
3SD YELLOW 2 RXD
4RD 3 TXD open the menu, choose I/O SETUP and
GREEN
5 + RED 4 DTR then press the [ENT] key.
6 - BLACK 6 DSR
7FG - + 7 RTS
8 CTS I/O SETUP
GP-32/37 12/24VDC DATA1 : NMEA-REM1
DATA2 : NMEA-REM
NMEA VER : VER2.0
Wiring diagram, using SAVE WPT/RTE → PC?
DSUB 9-pin connector LOAD WPT/RTE ← PC?
LOAD WPT← YEOMAN?
Note: A DSUB 25-pin (EIA-232) may also be WIRING INFO?
used to make the connection. In this case the

wiring diagram is as follows. I/O SETUP menu
1 TD-H
2. Choose SAVE WPT/RTE → PC?.
WHITE
2 TD-C/SG BLUE 7 GND 3. Press the [ENT] key.
3 SD YELLOW 3 RXD
4 RD GREEN 2 TXD
SAVE WPT/RTE
5 + RED 4 RTS
6 - BLACK 5 CTS ALL WPTS/ROUTES
7 FG - + 6 DSR WILL BE SAVED TO PC.
20 DTR
SET PC PORT TO 4800
8 BIT, P-N, S1, XON/OFF.
Wiring diagram, using
CONTINUE?
DSUB 25-pin connector
SAVE WP/RTE display

43
7. OTHER FUNCTIONS
LOADING START?
SAVING START? (PC READY?)
(PC READY?)
ARE YOU SURE?
ARE YOU SURE? YES NO
YES NO
LOADING START? prompt

SAVING START? prompt 5. Set up the computer to output data.
5. Set up the computer to receive data. 6. Press ◄ to choose YES and then press
6. Press ◄ to choose YES and then press the [ENT] key to upload.
the [ENT] key to download. Note: The waypoint and route data are
Data is being deleted when the [ENT] key is pressed.
WPTS & ROUTES saved. To can-
SAVING ... cel, press the WPTS & ROUTES Now loading
[ENT] key. LOADING.... data
CANCEL?
CANCEL? To cancel, press
[ENT] key.
Message when data is being loaded

7. When the loading is completed, the
Saving is following message appears.
SAVING completed.
COMPLETED Hit any key LOADING
to escape. COMPLETED.
HIT ANY KEY.
HIT ANY KEY.
Downloading sequence
7. Press any key to escape. Message when data is loaded successfully
8. Press any key to escape.
Uploading data from a PC
Note that all waypoint and route data stored Loading data from a YEOMAN
in the GP-37/GP-32 will be deleted when data Waypoint data from a YEOMAN has the
is uploaded. same format as does the NMEA 0183 data
sentence WPL.
open the menu, choose I/O SETUP and 1. Press the [MENU] key twice, choose I/O
then press the [ENT] key. SETUP and then press the [ENT] key.
2. Choose LOAD WPT/RTE ← PC?. 2. Choose LOAD WPT ← YEOMAN?.
3. Press the [ENT] key. 3. Press the [ENT] key.
LOAD WPT/RTE LOAD YEOMAN WPT

LOADING ERASES CUR- LOADING YEOMAN WPT
RENT WPT/RTE DATA. DATA.
SET PC PORT TO 4800

8 BIT, P-N, S1, XON/OFF.
CONTINUE? CONTINUE?
LOAD WP/RTE display LOAD YEOMAN WP display

44
7. OTHER FUNCTIONS
4. Press the [ENT] key. 7: Waypoint comment (2 byte for mark code
+ 16 characters of comment.)
LOADING START? 1st byte of mark code: Fixed to '@'.
(YEOMAN READY?)
2nd byte of mark code: Internal mark
ARE YOU SURE? code + 'a' (0 x 61). See Note 1 on the
YES NO next page.
Number of characters for comment is
LOADING START? prompt less than 16 (variable length). See Note 2
on the next page.
5. Set up the YEOMAN to output data.
8: Flag making waypoint. Always set to “A”.
“A”: Displayed
the [ENT] key to load data.
”V”: Not displayed
Now loading
WAYPOINTS
data 9: UTC (Always NULL)
LOADING....
10: Day (Always NULL)
END? To quit loading, 11: Month (Always NULL)
12: Year (Always NULL)
Message when waypoints are being loaded Note 1: Internal mark code is 0 x 10 through
7. Data is loaded to empty location and the 0 x 18. 0 x 71 through 0 x 79 are always
buzzer sounds twice to signify successful placed at 2nd byte of mark code.
loading. If there is not enough memory Note 2: Following characters can be used for
free to store the waypoints, the message comments:
below appears.
_ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789&()+-/=?}
WAYPOINTS FULL 0x10: (q) 0x11: (r) 0x12: (s) 0x13: (t) 0x14: (u)
FULLNOT LOADING
0x15: (v) 0x16: (w) 0x17: (x) 0x18: (y)
HIT ANY KEY.
Characters available for comments

Message when waypoints
could not be loaded Route data format
Waypoint data format

$GPRTE, x, x, a, cc, c----c, c----c, ... , c----c <CR><LF>
1 2 3 4 5 6 12
$PFEC, GPwpl, llll.lll, a, yyyyy.yyy, a, c----c, c, c----c, a, hhmmss, xx, xx, xxxx <CR><LF>
1 2 3 4 5 6 7 8 9 10 11 12
Route data format
Waypoint data format 1: Number of sentences required for one
1: Waypoint latitude complete route data (1 to 4). See Note.
2: N/S 2: Number of sentences currently used (1 to
3: Waypoint longitude 4)
4: E/W 3: Message mode (Always set to C).
5: Waypoint name (Number of characters is 4: Route No. (01 to 51 (51 is LOG route, 2
fixed to 6 and space code is placed when digits required)
the number of characters are less than 5 through 12: Waypoint name (Max. 8
6.) names, length of each
6: Waypoint color (This field is always kept waypoint name is fixed to 7
NULL.) byte)
45
7. OTHER FUNCTIONS
1st byte: Skip code '-' (Hyphen) = Skip 7.14 Language

ON, Space code = Skip OFF
English and other languages are available.
After 2nd byte: Waypoint name (fixed to
6 bytes) 1. Press the [MENU] key.
Note: A route can contain max. 30 waypoints [ENT] key.
and GPRTE sentence for one route data may 3. The cursor is selecting LANGUAGE.
exceed 80 byte limitation. In this case, route Press the [ENT] key.
data is divided into several GPRTE
sentences (Max. 4 sentences). This value ENGLISH ESPANOL
shows the number of sentences route data FRANCAIS ITALIANO
PORTUGUES DEUTSCH
has been divided.
NEDERLANDS (JAPANESE)
TIENG VIET INDONES
Route comment data format
Language options
$PFEC, GPrtc, xx, c----c <CR><LF> 4. Choose language desired and then press
1 2 the [ENT] key.
5. Press the [MENU] key once to return to
the main menu.
Route comment data format 6. Clear all backup data as shown in
1: Route No. (01 to 51, 2 digits required) paragraph 8.7.
2: Route comment (Max. 16 characters,
variable length)
The same characters of the comment for
waypoint comment can be used.
End of sentence
$PFEC, GPxfr, CTL, E <CR><LF>
End of sentence format
46
8. MAINTENANCE &
TROUBLESHOOTING
8.1 Maintenance 4. Press the [MENU] key twice to quit the
message board.
Regular maintenance is important to maintain
performance. Check the following points
Messages
monthly to help maintain performance.
Messages and their meanings
• Check that connectors on the rear panel
are firmly tightened and free of rust. Message Meaning, Remedy
• Check that the ground system is free of ANCHOR WATCH! Anchor watch alarm
rust and the ground wire is tightly fastened. violated.
ARRIVAL ALARM! Arrival alarm violated.
• Check that battery terminals are clean and
BACKUP ERROR RAM data corrupted.
free of rust.
DATA/ Try to clear backup
• Check the antenna for damage. Replace if data. See para. 8.4.
damaged. BATTERY ALARM! Voltage of battery in
display unit is low.
• Dust and dirt on the keyboard and display
Request replacement.
screen may be removed with a soft cloth.
NO DGPS SIGNAL! WAAS/DGPS alarm
Do not use chemical cleaners to clean the
violated. *1
equipment; they may remove paint and
GPS NO FIX! No GPS signal. Check
markings. Use special care when cleaning
antenna cable.
the LCD – it is easily scratched.
HIGH VOLTAGE! Power source voltage
too high.
LOW VOLTAGE! Power source voltage
8.2 Displaying the Message too low.
Board ODOMETER ALARM! Odometer distance
The message board displays error messages alarm violated.
and alerts. You can display it as follows: RAM ERROR! Request service.
ROM ERROR! Request service.
1. Press the [MENU] key once or twice to RTC ERROR! Request service.
open the menu. SPEED ALARM! Speed alarm violated.
2. Choose MESSAGES. TIME ALARM! Time alarm violated.
3. Press the [ENT] key. TRIP ALARM! Trip distance alarm
violated.
MESSAGES !
NO WAAS SIGNAL! WAAS/DGPS alarm
• NO GPS FIX! violated. *2
NO WAAS/DGPS WAAS/DGPS alarm
SIGNAL! violated. *3
XTE ALARM! XTE alarm violated.
*1 = WAAS/DGPS mode: INT/EXT BEACON
MESSAGE board *2 = WAAS/DGPS mode: WAAS
*3 = WAAS/DGPS mode: AUTO
47
8. MAINTENANCE & TROUBLESHOOTING
8.3 Replacing the Fuse 1. Turn on the power and then press the
[MENU] key once or twice to open the
The fuses (type: FGMB 125V 1A PBF, code
menu.
no.: 000-157-478-10) in the power cable (+/-
2 Choose SYS SETUP and then press the
lines) protects the equipment from
[ENT] key.
overcurrent, reverse polarity of the power
source and equipment fault. If the fuse blows,
SYSTEM SETUP
find the cause before replacing the fuse. If the
LANGUAGE : ENGLISH
fuse blows again after replacement, request DATUM : WGS84
service. UNITS : nm, kt
TIME DIFF : +00 : 00
TIME DISP : 24HOUR
WARNING TEST?
SIMULATOR?
Use the proper fuse. EXCHANGE BATTERY?
Use of a wrong fuse can result in damage

SYSTEM SETUP menu
to the equipment.
3. Choose “EXCHANGE BATTERY?” and
then press the [ENT] key. The display
shows the following message.
8.4 Replacing the Battery EXCHANGE
A lithium battery (type: CR2354-1F2, code BATTERY?
no.: 000-142-305) on the circuit board inside ARE YOU SURE?
the display unit preserves data when the YES NO
power is turned off. The life of the battery is
3-5 years. When its voltage is low, the
Exchange battery prompt
message shown below appears and data is
transferred from the RAM to the flash 4. Press ◄ to choose YES and then press
memory. the [ENT] key. The following display
appears.
BATTERY ALARM!
READY FOR
INTERNAL BATTERY BATTERY CHANGE.
VOLTAGE IS LOW. PRESS ANY KEY
REPLACE BATTERY. TO SHUT DOWN.
PUSH ENTER KEY TO
BACKUP WPTS,
Battery exchange
ROUTES & TRACKS.
confirmation window
5. Press any key to automatically turn off the
Low battery voltage warning
unit.
When this message appears, all open 6. Replace the battery.
windows are closed, no alarm will be
generated and no key input other than the Note 1: When it is expected that the
[ENT] key is accepted. Press the [ENT] key to equipment will not be used for a long time,
back up data and then turn off the power. execute the above procedure before turning
Contact your dealer to request replacement the power off, to prevent loss of data.
of the battery. Below is the procedure for
Note 2: Data is copied from the flash memory
replacing the battery.
to the RAM at the next power up.
48
8.5 Satellite Monitor Display 8.6 Diagnostics

The satellite monitor display shows The diagnostic test checks ROM, RAM, data
information about GPS and GEO satellites. port, beacon receiver, battery, RTC, keyboard
and LCD for proper operation.
open the menu. 1. Press the [MENU] key once or twice to
2. Choose SATELLITE. open the menu.
3. Press the [ENT] key. 2. Choose SYS SETUP and then press the
Number, bearing and elevation angle of [ENT] key.
all GPS and GEO satellites (if applicable) 3. Choose “TEST?” and then press the
in view of your receiver appear. Satellites [ENT] key. You are asked if you are ready
being used in fixing position are displayed to start the test.
in reverse video; satellites not being used TEST START ?
are shown in normal video. (STOP: PWR OFF)
Receive signal level ARE YOU SURE ?

Receiver Bars show signal level. YES NO
status Satellites whose signal
(See page 2.) level extends past the
dashed line are used TEST START? prompt
North in fixing position.
DOP value
the [ENT] key to start the test.
D3D DOP 01
5. The equipment tests ROM, RAM, data
Elevation N 1. 5 02 port, beacon receiver, internal battery and
07 --
45°
06 04 RTC. The results are individually
02 05
08 06 displayed as OK or NG (No Good).
04 07
10 08
12 -- TEST
05 10
01 W
-- ROM : OK
12 RAM : OK
85m 122 DATA2 : - - (STOP: PWR OFF)
BEACON : OK 085-0182-0XX
GEO satellite BATTERY : OK
GEO
RTC : OK 205-1412-0XX
satellite
Satellite number in reverse CNT: 001 205-1411-0XX
Altitude
video is used for positioning.
Elevation 5° XX = Program version no.
TEST results (GP-37)

Satellite monitor display
4. Press the [MENU] key twice to quit the Note 1: BEACON test result shown as
SATELLITE display. NONE when no beacon receiver is
connected to the GP-32.
Note 2: DATA2 requires a special

connector to check. “- -” appears as the
result when no connector is connected.
Note 3: No program number shown for

BEACON in case of the GP-32.
Note 4: CNT shows the number of times

the test has been executed consecutively.
49
6. After the equipment has displayed the test

ERASE GPS DATA?
results, a beep sounds and the message
PUSH KEY appears at the top right-hand
ARE YOU SURE?
corner.
YES NO
7. Press each key one by one. The name of
the key pressed momentarily appears at
the top right-hand corner if the key is GPS DATA
functioning properly.
Note: If no key is pressed within approx. MENU SETTINGS
five seconds, the equipment automatically TO DEFAULT?
proceeds to step 8. ARE YOU SURE?
8. The equipment displays the following YES NO
message to inform you that it is now going
to check the LCD: MENU SETTINGS
<LCD CHECK>
ERASE ALL BACKUP
ALL ON 2 SEC. DATA? (DEFAULT)
ALL OFF 3 SEC. ARE YOU SURE?
YES NO
LCD check
BACKUP DATA
9. The LCD is checked, and then the test is
repeated. To stop the test, turn off the Prompt for erasure of GPS data, menu
power. settings, backup data
the [ENT] key. The following display
8.7 Clearing Data appears.
You may clear GPS data, menu settings and RESTART FOR
all backup data to start afresh. ERASING DATA.
PUSH ANY KEY.

open the menu.
Prompt for restarting
key. 5. Hit any key to erase item selected. A
3. Choose GPS DATA, MENU SETTINGS, beep sounds while the selected item is
or ALL BACKUP DATA as appropriate being erased.
and then press the [ENT] key. One of the
following messages appears. Note 1: If you were using the simulation
mode when data is cleared, the message
“Start Simulation – Are You Sure? appears.
Choose YES and press the [ENT] key to start
the simulation mode, or press the [ENT] key
to start normal operation
50
Note 2: When the memory is cleared the default position is restored as below.
Language and default position, unit and time difference
Language Default Position Unit Time Difference

English 38°N, 123°W nm, kt 0:00
German 54°N, 10°E nm, kt 0:00
French 44°51E, 0°40W km, km/h 0:00
Spanish 40°26E, 3°40W nm, kt +2:00
Italian 42°N, 12°E nm, kt +1:00
Portuguese 22°44S, 43°10W nm, kt -3:00
Dutch 38°N, 123°W nm, kt 0:00
Vietnamese 12°15N, 109°13E nm, kt +7:00
Japanese 34°44N, 135°21E nm, kt +9:00
Indonesia 6°11S, 110°53E nm, kt +7:00
51
52
9. INSTALLATION
9.1 Installation of Display Unit Flush mounting
Mounting considerations There are two types of flush mounting kits.

For details, see the outline drawings at the
The display unit can be installed on a desktop,
end of this manual.
on the overhead, or in a panel (optional flush
mounting kit required). Refer to the outline Flush mount F kit
drawings at the end of this manual for
installation instructions. When choosing a Flush mount F kit
mounting location, keep in mind the following Type: OP20-29 Code No. 000-041-405
points:
Name Type Code No. Qty
• Locate the unit away from exhaust pipes Cosmetic 20-016-
and vents. 100-251-370 1
panel 1051
• The mounting location should be well Tapping 5X20
000-802-840 4
screw SUS304
ventilated.
Hexagon- M6X12
• Mount the unit where shock and vibration 000-862-127 2
head bolt SUS304
are minimal. Spring M6
000-864-260 2
• Locate the unit away from equipment which washer SUS304
generates electromagnetic fields such as a 1. Using the template (supplied), cut out a
motor or generator. hole 92(H)X183(W) in the mounting
• Allow sufficient maintenance space at the location.
sides and rear of the unit and leave 2. Fasten the cosmetic panel to the display
sufficient slack in cables, to facilitate unit with hexagon-head bolts and spring
maintenance and servicing. washers.
3. Set the display unit to the mounting
• Observe compass safe noted on page ii to
location and fix it with tapping screws.
prevent interference to a magnetic
compass.
Desktop and overhead mounting
Desktop Overhead
Desktop and overhead mounting methods
53
9. INSTALLATION
Flush mount S kit • Choose a location out of the radar beam.

The radar beam will obstruct or prevent
Flush mount S kit
reception of the GPS signal.
Type: OP20-17 Code No. 000-040-720
• The location should be well away from a
Name Type Code No. Qty
VHF/UHF antenna. A GPS receiver is
Flush mount 20-007- interfered by a harmonic wave of a
100-183-190 2
fixture 2401
VHF/UHF antenna.
Hexagon- M6X12
000-862-127 2
head bolt SUS304 • There should be no interfering object within
M4X30 the line-of-sight to the satellites. Objects
Wing bolt YBSC2 000-804-799 4 within line-of-sight to a satellite, for
MBN12 example, a mast, may block reception or
M4 prolong acquisition time.
Wing nut YBSC2 000-863-306 4
MBN12 • Mount the antenna unit as high as possible
Spring M6 to keep it free of interfering objects and
000-864-260 2 water spray, which can interrupt reception
washer SUS304
of GPS satellite signal if the water freezes.
1. Using the template (supplied), cut out a
hole (92(H)X167(W)) in the mounting
• See the outline drawing for the antenna
unit at the back of this manual for minimum
location.
separation distances from other antennas.
2. Fix the two flush mount fixtures to the
display unit with hexagon-head bolts and • If the antenna cable is to be passed
spring washers. through a hole which is not large enough to
3. Screw in wing nut in wing bolt. pass the connector, you may unfasten the
4. Set the display unit to the mounting connector with a needle nose pliers and
location and fix it with wing bolts and wing 3/8-inch open-end wrench. Refasten it as
nuts from the rear side. shown below, after running the cable
through the hole.
Spring
9.2 Installation of Antenna Washer
Gasket (reddish-brown)
Unit Shield
Nut
Mounting considerations Pin
Connector
Install the antenna unit referring to the
antenna installation diagram at the end of this
manual. When choosing a mounting location
How to assemble the connector
for the antenna unit, keep in mind the
following points:
• Do not shorten the antenna cable.

• The antenna unit can be installed three
ways: screwed into a pipe (local supply),
fixed to a post with the optional mast
mounting kit, or screwed into an optional
mounting base. For fixing by post or pipe, it
is recommended to use stays to secure the
post or pipe to prevent damage to the GPS
receiver by vibration.
54
9. INSTALLATION
9.3 Wiring Grounding
The illustration below shows where to The display unit contains a CPU. While it is
connect cables on the rear of the display unit. operating, it radiates noise, which can
Please review the INSTALLATION interfere with radio equipment. Ground the
GUIDELINES at the front of this manual unit as follows to prevent interference:
before wiring the equipment. • The ground wire for the display unit should
ANTENNA UNIT ANTENNA UNIT be 1.25sq or larger and as short as
GPA-017 GPA-019 possible.
(For GP-32) (For GP-37)
• The signal ground and frame ground are
separated, however the power line is not
OR isolated. Therefore, do not connect the
signal ground to the frame ground when
DISPLAY UNIT connecting other equipment to a positive
With 10 m GP-32 OR GP-37 ground battery.
cable
External equipment
MJ-A7SPF0009-020C,
2m The power supply port is commonly used for
connection of external equipment such as a
Ground radar. Refer to the interconnection diagram
on page S-1 or S-2 for connection of external
Black -
*+ Red equipment.
POWER
(12-24 VDC) 1A Fuse
(+/- line)
* = Cut unused cores
and tape individually.
Wiring
Note: The fuse holder contains a spring that

fixes the fuse. To prevent detachment of the
spring, which would cause loss of power, tie
the line as shown below.
Fuse Holder
+ Line (Red)
- Line (Black)
Fix here.
How to fix spring in fuse holder
55
9. INSTALLATION
9.4 Initial Settings DATA2
This equipment can output navigation data to External Beacon Internal Beacon
external equipment, in NMEA 0183 format. Receiver Setting Receiver Setting
For example, it can output position data to a Output Output of internal
GGA beacon receiver's
radar or echo sounder for display on its MSK correction data
display screen. (correction data and
Input $CRMSS)
Correction data of
Output data format, data sentences external beacon
receiver
NMEA 0183 version 1.5, 2.0 or 2.1 can be
selected from the I/O SETUP menu. BEACON on WAAS/DGPS BEACON on WAAS/DGPS
SETUP menu set to SETUP menu set to
EXT INT
DATA1: Current loop data
Data sentence description
With waypoint
Sentence Description
AP REM1 REM2
AAM Arrival alarm
GLL GLL GLL
APB Autopilot data (XTE and bearing to
VTG GGA GGA waypoint)
ZDA VTG VTG BOD Bearing from own ship to
*2
AAM ZDA ZDA destination
APB *2
RMC RMA (Ver 2.0)*1 BWC Range and bearing to waypoint
(great circle navigation)
BOD*2 RMB*2 GTD (Ver 1.5)*1
GGA GPS position fixing condition (time
BWC*2 RMC
of fix, latitude, longitude, receiving
XTE *2
RMB*2 condition, number of satellites
BWC*2 used, DOP)
(1 s interval: GLL Latitude and longitude
(1 s interval) (1 s interval) Ver. 2.1 GTD Loran-C time difference
2 s interval:
RMA Generic navigational information
Ver. 1.5/2.0)
*1
(latitude, longitude, Loran-C time
: Output when Loran C TDs are displayed. differences, ground speed, true
*2
: Not output when no waypoint is set. course
AP: Autopilot RMB Generic navigational information
(cross track error, steering
REM1/REM2: Radar, echo sounder, etc. direction, starting waypoint no.,
destination waypoint no., latitude
DATA2: RS-232C level and longitude of starting waypoint,
With waypoint latitude and longitude of destination
AP REM waypoint, range and bearing to
waypoint, range and bearing from
GLL GLL
present position to destination
VTG GGA
waypoint, velocity to destination,
ZDA VTG
arrival alarm)
AAM*2 ZDA
RMC Generic navigational information
APB*2 RMA (Ver 2.0)*1
(UTC time, latitude, longitude,
BOD*2 GTD (Ver 1.5)*1
ground speed, true course, day,
BWC*2 RMC month, year)
XTE*2 RMB*2
VTG Actual track and ground speeds
BWC*2
*1 XTE Course error amount and direction
: Output when Loran C TDs are displayed. to steer
*2
: Not output when no waypoint is set. ZDA UTC time (day, month, year)
56
9. INSTALLATION
Output setting 6. Use ▲ or ▼ to choose desired option.

1. Press the [MENU] key once or twice to NMEA-REM1, 2: Output data to radar,
open the menu. echo sounder, etc.
2. Choose I/O SETUP. NMEA-AP: Output data to an autopilot.
3. Press the [ENT] key. RTCM-OUT: Choose when equipped with
internal DGPS beacon receiver (GP-37).
I/O SETUP
VER 1.5, 2.0, 2.1: Choose the NMEA
DATA1 : NMEA-REM1
DATA2 : NMEA-REM version of external equipment. If you are
NMEA VER : VER2.0 unsure of the version number, try both
SAVE WPT/RTE → PC?
LOAD WPT/RTE ← PC?
and choose the one which successfully
LOAD WPT← YEOMAN? outputs data.
WIRING INFO?
I/O SETUP menu
4. Choose DATA1, DATA2 or NMEA VER as
appropriate.
5. Press the [ENT] key. One of the following
screens appears depending on the item
selected at step 4.
NMEA-REM1 NMEA-REM VER 1.5

NMEA-REM2 NMEA-AP VER 2.0
NMEA-AP RTCM-OUT* VER 2.1
For DATA1 For DATA2 For NMEA
Version
*= For GP-37, fixed at "BEACON" when MODE
on DGPS/WAAS menu is set to EXT BEACON.
DATA1, DATA 2 and NMEA version options
57
9. INSTALLATION
58
APPENDIX
Menu Tree
Default settings shown in bold italics.
MENU WAYPOINTS LIST, NEAREST
ROUTES VOYAGE ROUTE (START, STOP)

INTERVAL (TIME, 00H01M - 99H99M, 00H10M;
DISTANCE, 0.1 - 99.9 nm, 2 nm)
PLOTTER TRACK REC (OFF, DISTANCE, AUTO)

INTERVAL (0.10 nm)
BRG. REF (MAG, TRUE)
MAG. VAR. (AUTO, MAN)
WPT NAME (DSP GOTO, DSP ROUTE, DSP ALL)
TTG/ETA SPD (AUTO, MAN)
ALARMS BUZZER (SHORT, LONG, CONSTANT)

ARV/ANC (OFF, ARV, ANC)
XTE (OFF, ON)
SPEED (OFF, LOW, HIGH)
WAAS/DGPS (OFF, ON)
TIME (OFF, ON)
TRIP (OFF, ON)
ODOMETER (OFF, ON)
ERASE WAYPOINTS/MARKS?
ROUTES?
TRACK?
RESET TRIP?
RESET ODO?
GPS DATA?
MENU SETTINGS?
ALL BACKUP DATA?
WAAS/DGPS MODE (GPS, WAAS, INT BEACON, EXT BEACON, AUTO)

WAAS SEARCH (AUTO, MANUAL)
CORRECTIONS DATA SET (00-99, 02)
DGPS STATION (AUTO, MANUAL, LIST)
RATE (50, 100, 200 BPS)
FREQ (310.0 kHz)
CALCULATE MODE (WAYPOINTS, ROUTE), SPD (AUTO, MAN)
MESSAGES Displays operational messages.
SATELLITE Shows satellite status display.
(Continued on next page)
AP-1
APPENDIX
(Continued from previous page)
USER DISP 1 (OFF, DIGITAL

SPEEDOMETER) DIGITAL (Display division: , , ,
2 (OFF, DIGITAL Available data: Odometer, trip, time,
SPEEDOMETER) position, power voltage, SOG, COG,
range and bearing to waypoint, XTE,
TTG and ETA)
SPEEDOMETER
START FROM (-99 to +99; 0)
INTERVAL (01 to 99; 10)
GPS SETUP SMOOTH POS (0-999 SEC; 0 SEC)

SMOOTH S/C (0-9999 SEC; 5 SEC)
AVR. SPEED (0-9999 SEC; 60 SEC)
LAT OFFSET
LON OFFSET
DISABLE SV (Disable GPS satellite.)
FIX MODE (2D/ 2/3D) For 2D, default antenna height is 5 m.
SYS SETUP LANGUAGE (ENGLISH, FRANCAIS, PORTUGUES, NEDERLANDS,
TIENG VIET, ESPANOL, ITALIANO, DEUTSCH, (JAPANESE), INDONES)
DATUM (WGS84, WGS72, OTHER)
UNITS (nm, kt; km, km/h; sm, mph)
TIME DIFF (+00:00)
TIME DISP (12HOUR, 24HOUR)
TEST?
SIMULATOR? (MODE: ON, OFF, SPEED: 0-99 kt, 20 kt,
COURSE: MAN (40°), AUTO; LAT, 38°00'N, LON, 123°00'W)
EXCHANGE BATTERY?
I/O SETUP DATA1 (NMEA-REM1, NMEA-REM2, NMEA-AP)
DATA2 (NMEA-REM, NMEA-AP, RTCM-OUT*)
NMEA VER (VER 1.5, VER 2.0, VER 2.1)
SAVE WPT/RTE → PC?
LOAD WPT/RTE ← PC?
LOAD WPT ← YEOMAN?
WIRING INFO?
TD SETUP DISPLAY (XX.XXX', XX'XX.X" LC TD, DE TD)

LORAN C (7980: 23-43)
LORAN C ∆TD1, ∆TD2 (-99.9-+99.9;+00.0)
DECCA (25: G-P)
DECCA ∆TD1, ∆TD2 (-9.99-+9.99;+0.0)
* = For GP-37. Replaced with "BEACON" when MODE on DGPS/WAAS menu
is set to EXT BEACON.
AP-2
APPENDIX
Geodetic Chart List

001: WGS84 088: NORTH AMERICAN 1927 : Western United States
002: WGS72 089: : Eastern United States
003: TOKYO : Mean Value (Japan, Korea & 090: : Alaska
Okinawa) 091: : Bahamas (excl. San Salvador Is.)
004: NORTH AMERICAN 1927 : Mean Value (CONUS) 092: : Bahamas, San Salvador Is.
005: EUROPEAN 1950 : Mean Value 093: : Canada (incl. Newfoundland Is.)
006: AUSTRALIAN GEODETIC 1984 : Australia & Tasmania 094: : Alberta & British Columbia
007: ADINDAN : Mean Value (Ethiopia & Sudan) 095: : East Canada
008: : Ethiopia 096: : Manitoba & Ontario
009: : Mali 097: : Northwest Territories &
010: : Senegal Saskatchewan
011 : Sudan 098: : Yukon
012: AFG : Somalia 099: : Canal Zone
013: AIN EL ABD 1970 : Bahrain Is. 100: : Caribbean
014: ANNA 1 ASTRO 1965 : Cocos Is. 101: : Central America
015: ARC 1950 : Mean Value 102: : Cuba
016: : Botswana 103: : Greenland
017: : Lesotho 104: : Mexico
018: : Malawi 105: NORTH AMERICAN 1983 : Alaska
019: : Swaziland 106: : Canada
020: : Zaire 107: : CONUS
021: : Zambia 108: : Mexico, Central America
022: : Zimbabwe 109: OBSERVATORIO 1966 : Corvo & Flores Islands (Azores)
023: ARC 1960 : Mean Value (Kenya & Tanzania) 110: OLD EGYPTIAN 1930 : Egypt
024: : Kenya 111: OLD HAWAIIAN : Mean Value
025: : Tanzania 112: : Hawaii
026: ASCENSION IS. 1958 : Ascension Is. 113: : Kauai
027: ASTRO BEACON ÒEÓ : Iwo Jima Is. 114: : Maui
028: ASTRO B4 SOR. ATOLL : Tern Is. 115: : Oahu
029: ASTRO POS 71/4 : St. Helena Is. 116: OMAN : Oman
030: ASTRONOMIC STATION 1952 : Marcus Is. 117: ORDNANCE SURVEY OF GREAT BRITAIN 1936: Mean Value
031: AUSTRALIAN GEODETIC 1966 : Australia & Tasmania 118: : England
032: BELLEVUE (IGN) : Efate & Erromango Islands 119: : England, Isle of Man & Wales
033: BERMUDA 1957 : Bermuda Islands 120: : Scotland, & Shetland Islands
034: BOGOTA OBSERVATORY : Columbia 121: : Wales
035: GAUPO INCHAUSPE : Argentina 122: PICO DE LAS NIVIES : Canary Islands
036: CANTON IS. 1966 : Phoenix Islands 123: PITCAIRN ASTRO 1967 : Pitcairn Is.
037: CAPE : South Africa 124: PROVISIONS SOUTH CHILEAN 1963: South Chile (near 53°S)
038: CAPE CANAVERAL : Mean Value (Florida & Bahama 125: PROVISIONAL SOUTH AMERICAN 1956: Mean Value
Islands) 126: : Bolivia
039: CARTHAGE : Tunisia 127: : Chile-Northern Chile (near 19°S)
040: CHATHAM 1971 : Chatham Is. (New Zealand) 128: : Chile-Southern Chile (near 43°S)
041: CHUA ASTRO : Paraguay 129: : Columbia
042: CORREGO ALEGRE : Brazil 130: : Ecuador
043: DJAKARTA (BATAVIA) : Sumatra Is. (Indonesia) 131: : Guyana
044: DOS 1968 : Gizo Is. (New Georgia Is.) 132: : Peru
045: EASTER IS. 1967 : Easter Is. 133: : Venezuela
046: EUROPEAN 1950 (Con’t) : Western Europe 134: PUERTO RICO : Puerto Rico & Virgin Islands
047: : Cyprus 135: QATAR NATIONAL : Qatar
048: : Egypt 136: QORNOQ : South Greenland
049: : England, Scotland, Channel & 137: ROME 1940 : Sardinia Islands
Shetland Islands 138: SANTA BRAZ : Sao Maguel, Santa Maria
050: : England, Ireland, Scotland, & Islands (Azores)
Shetland Islands 139: SANTO (DOS) : Espirito Santo Is.
051: : Greece 140: SAPPER HILL 1943 : East Falkland Is.
052 : Iran 141: SOUTH AMERICAN 1969 : Mean Value
053: : Italy, Sardinia 142: : Argentina
054: : Italy, Sicily 143: : Bolivia
055: : Norway & Finland 144: : Brazil
056: : Portugal & Spain 145: : Chile
057: EUROPEAN 1979 : Mean Value 146: : Columbia
058: GANDAJIKA BASE : Republic of Maldives 147: : Ecuador
059: GEODETIC DATUM 1949 : New Zealand 148: : Guyana
060: GUAM 1963 : Guam Is. 149: : Paraguay
061: GUX 1 ASTRO : Guadalcanal Is. 150: : Peru
062: HJORSEY 1955 : Iceland 151: : Trinidad & Tobago
063: HONG KONG 1363 : Hong Kong 152: : Venezuela
064: INDIAN : Thailand & Vietnam 153: SOUTH ASIA : Singapore
065: : Bangladesh, India & Nepal 154: SOUTHEAST BASE : Porto Santo & Madeira Islands
066: IRELAND 1965 : Ireland 155: SOUTHWEST BASE : Faial, Graciosa, Pico, Sao
067: ISTS 073 ASTRO 1969 : Diego Garcia Jorge, & Terceira Is.
068: JOHNSTON IS. 1961 : Johnston Is. 156: TIMBALAI 1948 : Brunei & East Malaysia
069: KANDAWALA : Sri Lanka (Sarawak & Sadah)
070: KERGUELEN IS. : Kerguelen Is. 157: TOKYO : Japan
071: KERTAU 1948 : West Malaysia & Singapore 158: : Korea
072: LA REUNION : Mascarene Is. 159: : Okinawa
073: L. C. 5 ASTRO : Cayman Brac Is. 160: TRISTAN ASTRO 1968 : Tristan da Cunha
074: LIBERIA 1964 : Liberia 161: VITI LEVU 1916 : Viti Levu Is. (Fiji Islands)
075: LUZON : Philippines (excl. Mindanao Is.) 162: WAKE-ENIWETOK 1960 : Marshall Islands
076: : Mindanao Is. 163: ZANDERIJ : Surinam
077: MAHE 1971 : Mahe Is. 164: BUKIT RIMPAH : Bangka & Belitung Islands
078: MARCO ASTRO : Salvage Islands (Indonesia)
079: MASSAWA : Eritrea (Ethiopia) 165: CAMP AREA ASTRO : Camp Mcmurdo Area, Antarctica
080: MERCHICH : Morocco 166: G. SEGARA : Kalimantan Is. (Indonesia)
081: MIDWAY ASTRO 1961 : Midway Is. 167: HERAT NORTH : Afghanistan
082: MINNA : Nigeria 168: HU-TZU-SHAN : Taiwan
083: NAHRWAN : Masirah Is. (0man) 169: TANANARIVE OBSERVATORY 1925 : Madagascar
084: : United Arab Emirates 170: YACARE : Uruguay
085: : Saudi Arabia 171: RT-90 : Sweden
086: NAMIBIA : Namibia 172: Pulkovo 1942 : Russia
087: MAPARIMA, BWI : Trinidad & Tobago 173: FINNISH KKJ : Finland
AP-3
APPENDIX
Loran C Chains
Chain GRI S1 S2 S3 S4 S5
Central Pacific 4990 11 29 – – –
Canadian East Coast 5930 11 25 38 – –
Commando Lion (Korea) 5970 11 31 42 – –
Canadian West Coast 5990 11 27 41 – –
South Saudi Arabia 7170 11 26 39 52 –
Labrador Sea 7930 11 26 – – –
Eastern Russia 7950 11 30 46 61 –
Gulf of Alaska 7960 11 26 44 – –
Norwegian Sea 7970 11 26 46 60 –
Southeast USA 7980 11 23 43 59 –
Mediterranean Sea 7990 11 29 47 – –
Western Russia 8000 10 25 50 65 –
North Central USA 8290 11 27 42 – –
North Saudi Arabia 8990 11 25 40 56 69
Great Lakes 8970 11 28 44 59 –
South Central USA 9610 11 25 40 52 65
West Coast USA 9940 11 27 40 – –
Northeast USA 9960 11 25 39 54 –
Northeast Pacific (old) 9970 11 30 55 81 –
Icelandic 9980 11 30 – – –
North Pacific 9990 11 29 43 – –
Suez 4991 10 24
England, France 8940 12 30
Northwest Pacific 8930 11 30 50 70
Newfoundland East Coast 7270 11 25
Lessay 6731 10 39
BØ 7001 11 27
Sylt 7499 11 26
Ejde 9007 10 23 38
Saudia Arabia North 8830 11 25 39 56
Saudia Arabia South 7030 11 25 37 55
AP-4
APPENDIX
Decca Chains
Chain Chain Chain Location Chain Chain Chain Location

No. code No. code
01 South Baltic 0A Europe 25 Skagerrak 10B "
02 Vestlandet 0E " 26 North Persian Gulf 5C Persian Gulf &

India
03 Southwest British 1B " 27 South Persian Gulf 1C "
04 Northumbrian 2A " 28 Bombay 7B "
05 Holland 2E " 29 Calcutta 8B "
06 North British 3B " 30 Bangladesh 6C "
07 Lofoten 3E " 31 Saliyah 2F "
08 3F " 32 Hokkaido 9C Japan
09 North Baltic 4B " 33 Tohoku 6C "
10 North West 4C " 34 Kanto 8C Japan
11 Trondelag 4E " 35 Shikoku 4C "
12 English 5B " 36 Hokuriku 2C "
13 North Bothnian 5F " 37 Kita Kyushu 7C "
14 Southern Spanish 6A " 38 Namaqualand 4A Southern Africa
15 North Scottish 6C " 39 Cape 6A "
16 Gulf of Finland 6E " 40 Eastern Province 8A "
17 Danish 7B " 41 South West Africa 9C "
18 Irish 7D " 42 Natal 10C "
19 Finnmark 7E " 43 Dampier 8E Australia
20 French 8B " 44 Port Headland 4A "
21 South Bothnian 8C " 45 Anticosti 9C Northern America
22 Hebridean 8E " 46 East Newfoundland 2C "
23 Frisian Islands 9B " 47 Cabot Strait 6B "
24 Helgeland 9E " 48 Nova Scotia 7C "
AP-5
APPENDIX
AP-6
SPECIFICATIONS OF
GPS NAVIGATOR GP-32
DGPS NAVIGATOR GP-37
1 GPS RECEIVER
1.1 Receiving Channels
GPS 12 channels parallel, 12 satellites tracking
WAAS 1 channel
1.2 Rx Frequency 1575.42 MHz
1.3 Rx Code C/A code, WAAS
1.4 Position Fixing System All in view, 8-state Kalman filter
1.5 Position Accuracy
GPS 10 m (95% of the time, HDOP=4)
DGPS 5 m (95% of the time, external data required)
WAAS 3 m (95% of the time)
1.6 Tracking Velocity 999 kt
1.7 Position-Fixing Time Warm start: 12 s approx., Cold start: 90 s approx.
1.8 Position Update interval 1 s
1.9 Beacon Receiver (GP-37 only)
Frequency Range 283.5 kHz to 325.0 kHz
MSK Rate 50,100,200 bps (Auto/Manual selectable)
2 RECEIVER UNIT
2.1 Display System Monochrome LCD, 95 (W) x 60 (H) mm, 120 x 64 dots
2.2 Display Mode Plotter, Steering, Highway, NAV data, Destination, User display
2.3 Projection Mercator
2.4 Memory Capacity Track: 1000 pts, Waypoint: 999 pts w/ comment
2.5 Storage Capacity 50 routes w/ 30 waypoint each
2.6 Alarms Arrival and anchor watch, Cross track error, Odometer alarm,
Ship’s speed in and out alarms, Time alarm, Trip alarm,
WAAS/DGPS alarm
2.7 Display Scale
Plotter Display 0.02/0.05/0.1/0.2/0.5/1/2/5/10/20/40/80/160/320 nm
Highway Display 0.2/0.4/0.8/1/02/4/8/16 nm
3 INTERFACE
3.1 Data 1 Current Loop
Output Data: NMEA0183 Ver 1.5/2.0/2.1 selected
SP - 1 E4420S01C-M
NMEA-REM1: GLL, GGA, VTG, ZDA, RMC, RMB
NMEA-REM2: GLL, GGA, VTG, ZDA, RMC, RMB, BWC,
RMA (Ver2.0), GTD (Ver1.5) when TD indication selected
NMEA-AP: GLL, VTG, ZDA, AAM, APB, BOD, BWC, XTE
3.2 Data 2 RS-232C
Output Data: NMEA0183 Ver 1.5/2.0/2.1 selected
NMEA-REM: GLL, GGA, VTG, ZDA, RMC, RMB, BWC,
RMA (Ver2.0), GTD (Ver1.5) when TD indication selected
NMEA-AP: GLL, VTG, ZDA, AAM, APB, BOD, BWC, XTE
DGPS RTCM SC-104 (GP-37 only)
Downloading to PC (WP/ Route Data)
Input Data: DGPS RTCM SC-104 Ver 2.1
Uploading from PC (WP/ Route Data)
NMEA WPL (WP Data)
4 POWER SUPPLY
4.1 GP-32: 12-24 VDC: 240-120 mA
4.2 GP-37: 12-24 VDC: 340-170 mA
5 ENVIRONMENTAL CONDITION
5.1 Ambient Temperature Antenna unit: -25°C to +70°C
Receiver unit: -15°C to +55°C
5.2 Damp Heat 93% or less at 40°C
5.3 Waterproofing Antenna unit: IPX6
(IEC 60529) Receiver unit: IPX5 (USCG CFR-46)
5.4 Vibration IEC 60945
6 COATING COLOR
6.1 Antenna Unit N9.5
6.2 Receiver Unit Chassis: 2.5GY5/1.5, Panel: N3.0
SP - 2 E4420S01C-M
D-1
Sep.29'05
D-2
Feb. 19, '03

Y. Hatai
D-2A
hatai
2005.12.19
11:57:12
+09'00'
1 2 3 4
空中線部
外部機器
例） ANTENNA UNIT
レーダー受信演算部 GPA-017
魚群探知機
オートパイロット RECEIVER UNIT
リモートディスプレイ
A プロッタ GP-32
RD-H ANT TNC-P-3
EXT EQUIPMENT
EX: RD-C 3D-2V,10m,φ5.3
RADAR
ECHO SOUNDER
AUTOPILOT
REMOTE DISPLAY *2
PLOTTER MJ-A7SPF0009,2m MJ-A7SPFD J1 *4
シロ WHT 1 TD-H DATA1 CURRENT LOOP
NMEA0183(Ver1.5/2.0/2.1)
パーソナルコンピュータ SG アオ BLU 2 TD-C/SG
PC DATA2 RS-232C
外部ビーコン受信機 PC YEL NMEA0183(Ver1.5/2.0/2.1)
RD キ 3 SD
EXTERNAL BEACON RECEIVER RTCM SC-104
SD ミドリ GRN 4 RD UP LOAD/DOWN LOAD
船内電源 FUSE 1A (WP,ROUTE)
アカ RED 5 (+)
SHIP'S MAINS (+) 12-24VDC IN
12-24 VDC (-) クロ BLK 6 (-)
1A
7 FG
100/110/115/
220/230 VAC
B 1φ,50/60Hz (+)(-)
整流器 *1
RECTIFIER
GND *1
IV-1.25SQ
注記
＊１）現地手配
＊２）コネクタは工場にて取付済み
＊３）オプション
C ＊４）メニューにより選択 DRAWN TITLE
May 13 '03 T.YAMASAKI GP-32
NOTE CHECKED 名称
*1. LOCAL SUPPLY. May 13 '03 T.TAKENO GPS航法装置
*2. FITTED AT FACTORY. APPROVED
May 13 '03 相互結線図
*3. OPTION.
SCALE MASS NAME
*4. SELECT ON MENU. kg GPS NAVIGATOR
S-1
DWG.No.
C4420-C01- B INTERCONNECTION DIAGRAM
1 2 3 4
空中線部
外部機器
例） ANTENNA UNIT
レーダー受信演算部 GPA-019
魚群探知機
オートパイロット RECEIVER UNIT
リモートディスプレイ
A プロッタ GP-37
RD-H ANT TNC-P-3
EXT EQUIPMENT
EX: RD-C 3D-2V,10m,φ5.3
RADAR
ECHO SOUNDER
AUTOPILOT
REMOTE DISPLAY *2
PLOTTER MJ-A7SPF0009,2m MJ-A7SPFD J1 *4
シロ WHT 1 TD-H DATA1 CURRENT LOOP
NMEA0183(Ver1.5/2.0/2.1)
SG アオ BLU 2 TD-C/SG DATA2 RS-232C
パーソナルコンピュータ PC
PC RD キ YEL 3 SD NMEA0183(Ver1.5/2.0/2.1)
RTCM SC-104[OUTPUT]
SD ミドリ GRN 4 RD UP LOAD/DOWN LOAD
船内電源 FUSE 1A (WP,ROUTE)
アカ RED 5 (+)
SHIP'S MAINS (+) 12-24VDC IN
12-24 VDC (-) クロ BLK 6 (-)
1A
7 FG
100/110/115/
220/230 VAC
B 1φ,50/60Hz (+)(-)
整流器 *1
RECTIFIER
GND *1
IV-1.25SQ
注記
＊１）現地手配
＊２）コネクタは工場にて取付済み
＊３）オプション
C ＊４）メニューにより選択 DRAWN TITLE
May 13 '03 T.YAMASAKI GP-37
NOTE CHECKED 名称
*1. LOCAL SUPPLY. May 13 '03 T.TAKENO DGPS航法装置
*2. FITTED AT FACTORY. APPROVED May 13 '03
相互結線図
*3. OPTION.
SCALE MASS NAME
*4. SELECT ON MENU. kg DGPS NAVIGATOR
S-2
DWG.No.
C4419-C01- B INTERCONNECTION DIAGRAM
INDEX
Digital display
A
overview ..................................................... 6
Alarms
setting up.................................................. 41
anchor watch ............................................30
DIM/PWR key................................................. 2
arrival ........................................................29
Dimmer........................................................... 2
buzzer type ...............................................32
DISP key ........................................................ 3
odometer...................................................32
Downloading data to a PC ........................... 43
speed ........................................................31
time ...........................................................31 E
trip .............................................................32 Erasing
WAAS/DGPS ............................................31 routes
XTE ...........................................................30 track...........................................................11
Alarms menu ................................................29 waypoints (marks) .................................... 17
Anchor watch alarm......................................30
F
Arrival alarm .................................................29
Fuse replacement ........................................ 48
B
G
Battery replacement .....................................48
Geodetic chart system
Bearing reference .........................................37
list ......................................................... AP-3
Buzzer...........................................................32
selection ................................................... 38
C GOTO key .............................................. 27, 28
Calculation menu..........................................33 GPS setup menu.......................................... 40
Centering (own ship mark) ...........................10
H
Clearing data ................................................50
Highway display ............................................. 4
Contrast ..........................................................2
Controls ..........................................................1 I
Cursor .............................................................9 Installation ................................................... 53
D L
Decca chains ............................................AP-5 Language ..................................................... 46
Destination Loran C chains ......................................... AP-4
canceling...................................................28 M
setting by cursor .......................................27 Magnetic variation........................................ 38
setting by route .........................................28 Maintenance................................................. 47
setting by user waypoint ...........................28 MARK/MOB key........................................... 15
setting by waypoint ...................................27 MENU key ...................................................... 7
DGPS Menu tree ................................................. AP-1
editing user channels................................36 Messages..................................................... 47
erasing all user channels..........................37 MOB mark .................................................... 15
erasing individual user channels ..............37
N
programming user channels.....................36
Nav data display ............................................ 5
setup .........................................................35
Diagnostics ...................................................49 O
Odometer alarm ........................................... 32
Odometer resetting ...................................... 42
Index-1
INDEX
P erasing.......................................................11
Plotter display ................................................. 4 plotting interval ......................................... 10
Position offset ...............................................40 starting, stopping plotting ......................... 10
Trip alarm ..................................................... 32
R
Trip resetting ................................................ 42
Receiver status indications ............................ 2
Routes U
changing route name................................25 Units of measurement.................................. 38
creating track-based .................................22 Uploading data from a PC ........................... 44
creating with cursor ..................................19 User display
creating with waypoints ......................20, 21 overview ..................................................... 6
deleting waypoints from............................24 setting up.................................................. 41
destination ................................................28 User waypoint .............................................. 28
erasing ......................................................25
W
inserting waypoints ...................................24
WAAS
replacing waypoints ..................................23
description ................................................. vii
skipping waypoints ...................................24
setup......................................................... 34
S WAAS/DGPS alarm ..................................... 31
Satellite disabling .........................................40 WAAS/DGPS menu ............................... 34, 35
Satellite monitor............................................49 Waypoints (marks)
Shifting the display .......................................10 displaying name ....................................... 16
Simulation display .......................................... 8 editing....................................................... 16
Smoothing entering at own ship position ................... 14
position .....................................................40 entering through the waypoint list ............ 14
speed/course ............................................41 entering with cursor.................................. 13
Speed alarm .................................................31 erasing...................................................... 17
Speed averaging ..........................................40 setting as destination ............................... 27
Speedometer display user waypoint ........................................... 28
overview...................................................... 6 waypoints/marks list (nearest) ................. 17
setting up ..................................................42 Wiring diagram............................................. 43
Steering display.............................................. 5
X
System configuration..................................... vi
XTE alarm .................................................... 30
T
Y
TD setup menu .............................................38
Yeoman data loading ................................... 44
Time..............................................................39
Time alarm....................................................31 Z
Track Zoom .............................................................. 9
Index-2

GP-32 Ome-44200-E3

Uploaded by

Copyright:

Available Formats

GP-32 Ome-44200-E3

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

GP-32 Ome-44200-E3

Uploaded by

Copyright:

Available Formats

Back

FURUNO Authorized Distributor/Dealer

All rights reserved. Printed in Japan FIRST EDITION : MAY. 2002

( YOSH ) GP-32/37 *00080928811*

Continued use of the equipment can cause

Use the proper fuse.

Use of a wrong fuse can damage the

Improper handling can result in electrical Standard Steering

Fire or electrical shock can result if the

Be sure that the power supply is

Connection of an incorrect power supply

Use the proper fuse.

Use of a wrong fuse can damage the

FOREWORD ................................... v 6. ALARMS................................... 29

* = With DGPS beacon receiver

GP-37 system configuration

GP-32 system configuration

40°N EGNOS 40°N

122 120 131 134

Satellite, Region Position Expected operations capability

MARK Momentary press: Inscribes mark.

DIM Momentary press: Turns

To remove the hard cover, do as follows:

1.2 Turning On and Off Power Turning off the power

Note: The example screens shown in this

Your equipment takes about 90 seconds to BRILL (1~8)

* = DOP (Dilution of Precision) is the index of

1.4 Display Modes

[DISP] key COG: X

[User Display: Speedometer] [Plotter Display]

12.1 9.9 COG 357° 0.05

9.99 5.6 SOG10.0

[User Display: Digital Data] [Highway Display]

D2D MAG CURSOR 15:37

[Nav Data Display] [Steering Display]

Display modes (default user displays)

D2D X Waypoint mark

Direction to steer (to return to course)

CURSOR Destination waypoint name

BRG 11° [+]

Own ship mark

Range from own ship RNG: 0.16 nm BRG: 60° Bearing

D2D 10-JAN-02 16 :44 :15 Date and time

Speed over ground SOG: 12.5 kt COG: 7° Course over ground

Nav data display

1.5 Menu Overview

WAYPOINTS MESSAGES 1. Press the [MENU] key once or twice to

PLOTTER SETUP menu SYSTEM SETUP

1. Press the [MENU] key once or twice to SIM

▲ OUT Cursor mark Cursor position in

Cursor turned off 2.5 Changing Track Plotting

COG: 1. Press the [MENU] key once or twice to

TRACK MEMORY USED 1%

6. For AUTO or OFF, go to step 7. For

2.6 Erasing Track

1. Press the [MENU] key once or twice to

ARE YOU SURE?

Prompt for erasure of track

(This page intentionally left blank.)

( YOSH ) GP-32/37 00080928811