ZL-7830 Series Humidity Controller: Suzhou Lily Tech Co., LTD

Suzhou Lily Tech Co., Ltd.
ZL-7830 Series Humidity Controller

Instruction Manual A1.0
Feature
ZL-7830 series are humidity controller with 30A output relay. Compact with IP65 level front panel, convenient operation
and easy installation.
Model Function
Model Function
ZL-7830A Humidify / de-humidify
ZL-7830B Humidify / de-humidify; Alarm output
Specification
 Power supply: 100 ~ 240Vac, 50/60Hz
 Input signal: one humidity sensor (L = 1500mm)
 Output load: R1, 30A/250Vac. R2/R3, 3A/250Vac. The parameters are based on resistive load.
 Set range: humidity 0 ~ 100% RH. Resolution 0.1%
 Absolute measurement accuracy: humidity 5%
 Working environment: -20 ~ 45℃, 10 ~ 90% RH without dewing
 Device dimension: 78 * 34.5 * 71 (mm, W * H * D)
 Drilling template: 71 * 29 (mm, W * H)
 Case materials: PC + ABS (fireproof)
 Protection level: IP65 (front panel)
Key and Display

When there is no key operation for 30 seconds, the display will dim for power saving
www.suzhoulily.com.cn/en Page 1, Total 3 Pages

Icon Function On Blinking

Humidity load(R1) Energized Within delay protection time (see U12 bellow)
Humidify mode Humidify mode Setting set-point
De-humidify mode De-humidify mode Setting set-point
Alarm ---- Alarming
Display temperature Displaying temperature
Display humidity Displaying humidity
E1 Fault code ---- Sensor failure
E2 Fault code ---- Over humidity up limit
E3 Fault code ---- Over humidity low limit
UnL Hint Will restore to factory default ----
settings
Key Operation
Set Set-point
Keep〖S〗depressed for 3 seconds, the display shows the current set-point.
Press〖▲〗or〖▼〗to set the value. Keeping depressed can fast set.
Press〖S〗to exit, and the set will be saved.
If there is no key operation for 30 seconds, exit, and the set will not be saved.
Set Parameters
Keep〖P〗depressed for 3 seconds:
If the code is not “0000”, the display shows “---0”.
Press〖▼〗to select the digit of the password. Press〖▲〗to set the value (0 ~ 9) of the digit.
Press〖S〗to confirm. If the password is correct, enter into the set status. Else exit.
If the code is “0000”, then the password is not necessary. Enter into the set status directly.
At parameter set status:

Press〖▲〗or〖▼〗to select the code.
Press〖S〗to set the value of the code.
Press〖▲〗or〖▼〗to set the value.
Press〖S〗to return.
Keep〖P〗for 3 seconds to exit, and save the settings.
If there is no key operation for 30 seconds, exit, and no set will be saved.
Parameter Table
Code Function Range Remark Default
U10 Humidify / de-humidify H/P H: humidify; P: de-humidify P
U11 Hysteresis 0.1 ~ 20% 5
U12 R1 delay protection 0 ~ 30 min 0
U13 Humidity calibration -9.9 ~ +9.9% 0
U14 Humidity up limit 0 ~ 100% 100
U15 Humidity low limit 0 ~ 100% 0
U16 Over limit alarm delay 0 ~ 600 sec 30
U99 Password 0000 ~ 9999 0000: no password is necessary 0000

Control Function
Humidity Control (R1)
Dehumidify control (U10 = P)
If room humidity ≥ set-point, and R1 has stopped for U12, R1 will be energized.
If room humidity ≤ set-point – U11, R1 will be de-energized.
Humidify control (U10 = H)

If room humidity ≤ set-point, and R1 has stopped for U12, R1 will be energized.
If room humidity ≥ set-point + U11, R1 will be de-energized.
Power up delay protection

After power supplied, R1 could be energized only after U12 has passed.
Warning
When sensor fails, the controller displays blinking “E1”, keeps beeping, R1 is de-energized.
When room humidity ≥ U14 for U16 time, the controller displays “E2”, keeps beeping, alarm output acts, R1 keeps.
When room humidity ≤ U15 for U16 time, the controller displays “E3”, keeps beeping, alarm output acts, R1 keeps.
Alarm output:
Terminal Remark
R3 Open when alarm. Close when ok. Open when no power supply.
R2 Close when alarm. Open when ok. Close when no power supply.
COM Common terminal
Sensor Calibration
When the sensor has tolerance, it can be calibrated by U13.
Restore to Factory Default Settings

Keep〖P〗and〖▲〗depressed for 3 seconds, the controller displays “UnL”. Pressing〖▼〗twice will restore all settings
to factory default settings.
Installation Attention
Insert the controller into drilling hole.  Do not connect and de-connect lines when power
Slide the bracket to fix the device. supplied, including sensor.
 Please read this instruction carefully. Electrical

wiring must be manipulated by certified electrician.
Wrong wiring may damage the device and system
seriously.
 Avoid working in humid environment, or with

corrosive gases, or strong electric-magnetic field.
The device is possible abnormal in such condition.
Terminal Drawing  This product has been strictly tested before shipping.
The company warranty is one year, the
responsibility is limited to the sale of the product
itself. Damage caused by improper usage is not
covered by the warranty.

ZL-7830 Series Humidity Controller: Suzhou Lily Tech Co., LTD

Uploaded by

Copyright:

Available Formats

ZL-7830 Series Humidity Controller: Suzhou Lily Tech Co., LTD

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ZL-7830 Series Humidity Controller: Suzhou Lily Tech Co., LTD

Uploaded by

Copyright:

Available Formats

Suzhou Lily Tech Co., Ltd.

ZL-7830 Series Humidity Controller

Key and Display

www.suzhoulily.com.cn/en Page 1, Total 3 Pages

Icon Function On Blinking

At parameter set status:

www.suzhoulily.com.cn/en Page 2, Total 3 Pages

Humidify control (U10 = H)

Power up delay protection

Restore to Factory Default Settings

 Please read this instruction carefully. Electrical

 Avoid working in humid environment, or with

www.suzhoulily.com.cn/en Page 3, Total 3 Pages

You might also like