Scribd
Upload
89 views2 pages

ATA 36 AIRBUS 319/320: TH TH

The document contains 17 multiple choice questions about the bleed air system on an Airbus 319/320 aircraft. Specifically, it covers topics like: - Which stages of the V2500 engine high pressure compressor air is bled from - How the APU bleed valve operates with an LH duct or APU leak - How the Pressure Regulator Bleed valve is controlled - Components of the bleed air system like the precooler and overpressure valve

Uploaded by

Irvan Albab
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
89 views2 pages

ATA 36 AIRBUS 319/320: TH TH

The document contains 17 multiple choice questions about the bleed air system on an Airbus 319/320 aircraft. Specifically, it covers topics like: - Which stages of the V2500 engine high pressure compressor air is bled from - How the APU bleed valve operates with an LH duct or APU leak - How the Pressure Regulator Bleed valve is controlled - Components of the bleed air system like the precooler and overpressure valve

Uploaded by

Irvan Albab
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

ATA 36 AIRBUS 319/320

1 Which stages of the V2500 engine high pressure (HP) compressor are the air bled from?:-

(a) 5th and 8th stage.

(b) 7th and 10th stage.

(c) 8th and 10th stage.

2 If the LH duct or APU leak occurs and the APU BLEED switch is selected ON, the APU bleed valve would:-

(a) only be opened if main engine start is initiated.

(b) be latched closed permanently.

(c) only be opened if the APU is running above 95% RPM.

3 The Pressure Regulator Bleed valve (PRV) is pneumatically controlled by the :-

(a) HP Bleed Valve Closure Control Solenoid.

(b) Control Thermostat (CT).

(c) Bleed Pressure Regulated Valve Control Solenoid (CTS).

4 A double loop leak detection system is provided for:-

(a) pylons and aft-fuselage APU duct.

(b) wings, packs and mid-fuselage APU duct.

(c) wings, packs and pylons.

5 With the X-BLEED selector switch in AUTO, the crossbleed valve is controlled:-

(a) depending on either engine bleed valve position.

(b) independently of APU bleed valve.

(c) to the same position as the APU bleed valve.

6 The Bleed Pressure Regulated Valve Control Solenoid (CTS):

(a) regulates the engine bleed air transfer pressure.

(b) prevents reverse air flow through the precooler.

(c) prevents reverse air flow through the engine PRV.

7 The FAULT light on the ENG 1 BLEED pushbutton switch will comes on if there is an overheat condition in
the:

(a) LH Zone (LH Pylon, LH Wing and LH MID fuselage).

(b) RH Zone (RH Pylon, RH Wing and RH MID fuselage).

(c) LH Zone, MID and AFT Fuselage (LH Pylon, LH Wing, LH MID fuselage and APU duct).

8 The precooler is a heat exchanger located:

(a) upstream of the Pressure Regulator Bleed Valve (PRV).

(b) downstream from the Pressure Regulator Bleed Valve (PRV).

(c) upstream of the Fan Air Valve (FAV).

9 The APU can supply bleed air up to:-

(a) an altitude of 17,000 feet.

(b) an altitude of 20,000 feet.

(c) the aircraft ceiling.

1
10 If one Bleed Monitoring Computer (BMC) fails, the remaining BMC is:-

(a) able to monitor both bleed systems completely.

(b) able to monitor both bleed systems except for pylon leak and APU leak detection.

(c) only able to monitor its corresponding bleed system except for pylon leak and APU leak detection.

11 On V2500 engine, the Overpressure valve (OPV) is located:-

(a) downstream of the Precooler.

(b) downstream of the PRV.

(c) upstream of the PRV.

12 APU leak detection loop is connected to:-

(a) BMC 1 only.

(b) BMC 2 only.

(c) both BMC 1 and BMC 2.

13 When engine speed is low (during aircraft descent with engine at idle), the air is bled from:

(a) the IP port (7th stage intermediate pressure).

(b) the HP port (high pressure 10th stage).

(c) Both IP and HP ports ( 7th and 10th stages).

14 With the crossbleed valve selector switch to OPEN position, which motor(s) is/are being used?:

(a) Motor 1 only.

(b) Motor 2 only.

(c) Both Motor 1 & Motor 2.

15 On the ground with an external air is connected to HP ground connector and the crossbleed valve is closed,:

(a) only the left manifold is pressurised.

(b) only the right manifold is pressurised.

(d) Both (a) and (b) are correct.

16 The Engine Bleed Valve (PRV) is:-

(a) electrically-controlled, pneumatically-operated valve.

(b) pneumatically-controlled, electrically-operated valve.

(c) a spring-loaded open valve in the absence of air pressure.

17 The FAULT light on the ENG 1(2) BLEED switch of the AIR COND control panel illuminates when:-

(a) there is an overtemperature downstream of the precooler.

(b) the bleed air temperature reaches approximately 245C.

(c) a low pressure is detected downstream of the bleed valve (PRV).

You might also like