Scribd
Upload
88 views2 pages

Laser Controller: Type: Ls11-La16v60-T19208-V0-872

This document summarizes the specifications and features of the ls11-la16v60-t19208-v0-872 laser controller. It can control lasers up to 16A and 60V with rise and fall times under 30μs. It has external, internal, analog and digital modulation capabilities as well as current monitoring, bias current options, and pilot laser supply. Connections include laser, Peltier, RS232, AMOD/DMOD-IN and interlock connectors. Accessories include an RS232 to USB converter and cables.

Uploaded by

Vandana Singh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
88 views2 pages

Laser Controller: Type: Ls11-La16v60-T19208-V0-872

This document summarizes the specifications and features of the ls11-la16v60-t19208-v0-872 laser controller. It can control lasers up to 16A and 60V with rise and fall times under 30μs. It has external, internal, analog and digital modulation capabilities as well as current monitoring, bias current options, and pilot laser supply. Connections include laser, Peltier, RS232, AMOD/DMOD-IN and interlock connectors. Accessories include an RS232 to USB converter and cables.

Uploaded by

Vandana Singh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Laser Controller

Type: ls11-la16v60-t19208-v0-872
Laser max.: 16A, 60V
trise, tfall < 30µs
supply voltage: 100~230VAC - 50/60Hz
- External, Internal, Analog and Digital Modulation
- Current Monitor
- Bias Current option
- Pilot Laser Supply
- External Fan Support
- optional additional TEC-stages
- incl. Laser Sequencer

Peltier Connector

SubD-15 female
PIN.No Abbr. Function
1 n.c. (optional) +12V - Fibre Sensor Supply
2 n.c. (optional) FIN - Fibre Sensor Input
4 LLED Laser ON LED Anode (+) ILED ca.5mA, vs. GND
5 PL+ Pilot Laser (+), vs. GND
6 PDC- Photo Diode Cathode (-) Input
10 n.c. (optional) +5V - Photo_Amp Supply 5V
11 T1 Temperature Sensor Input, vs. GND (default NTC10k)
12 GND Common Ground
13 S1-24V 1-24V adjustable Supply, max. 500mA, vs. GND, for fan etc.
Laser Connector
PIN. No Abbr. Function

A1 LANO+ Laser Diode Anode (+)

SubD2W2-female A2 LCAT- Laser Diode Cathode (-)

RS232 Connector AMOD/DMOD-IN Connector MOD-OUT Connector Interlock Connector

SubD-9 female BNC-Socked BNC-Socked, current monitor Jack Connector 3.5mm


Standard RS232-Connector Input-Impdanz 10kOhm 0-Imax[A] -> 0-4[V] Laser runs only if closed
(No Null-Modem Cable !) Digital Modulation with TTL-Pegel Take care for laser isolation if you (ca. 5mA over 2V -> R <= 400R)
Analog Mod. 0-4[V] => 0-Imax[A] connect GND potential to an
oscilloscope f.e.

c_l_t19208_v0_872 VER:03 OsTech (c) 10.10.2019 1/2


Laser Controller

Revision overview:
2019.01.03: „v0“ – newly derived from type 321, configuration with 5 Years Warranty
References:
http://www.ostech.de/en/products/laser-drivers/ds11-t192
http://www.ostech.de/en/downloads/manuals/ds-en.pdf
http://www.ostech.de/en/downloads/labview

Accessories
- acc-converter-usb-to-rs232-1m5-iso-417
RS232 to USB converter optical isolated with FTDI-Chip cable 1.5m
- kab-lpa08-16pol-subd15m-oe-1.5m-39
cable 16x0.35qmm / subd15-Gold-6,5A per pin to open end / length-1m5
- kab-la40-2pol-2W2male-oe-1.5m-286
cable 2x4qmm / imax-40A subd-2W2m-male to open-ends / length-1m5

c_l_t19208_v0_872 VER:03 OsTech (c) 10.10.2019 2/2

You might also like