Cisco − Basic CSS Load−Balancing Configuration

Table of Contents
Basic CSS Load−Balancing Configuration.......................................................................................................1
Document ID: 12557................................................................................................................................1
Introduction..........................................................................................................................................................1
Prerequisites.........................................................................................................................................................1
Requirements..........................................................................................................................................1
Components Used...................................................................................................................................1
Conventions............................................................................................................................................2
Background Theory................................................................................................................................2
Configure.............................................................................................................................................................2
Bridge VLANs to Ethernet Interfaces.....................................................................................................2
Number the Circuit VLANs....................................................................................................................2
Create a Service and Keepalive..............................................................................................................3
Create a Content Owner..........................................................................................................................3
Create a Content Rule and Virtual IP Address.......................................................................................3
Add Services to a Content Rule..............................................................................................................3
Sample Configuration..........................................................................................................................................4
Verify...................................................................................................................................................................5
Basic Troubleshooting.........................................................................................................................................5
Related Information.............................................................................................................................................5

i
Basic CSS Load−Balancing Configuration
Document ID: 12557

Introduction
Prerequisites
Requirements
Components Used
Conventions
Background Theory
Configure
Bridge VLANs to Ethernet Interfaces
Number the Circuit VLANs
Create a Service and Keepalive
Create a Content Owner
Create a Content Rule and Virtual IP Address
Add Services to a Content Rule
Sample Configuration
Verify
Basic Troubleshooting
Related Information

Introduction
This document walks you through a basic Content Services Switch (CSS) load−balancing configuration and
explains the functions of each configuration element. This document does not describe in detail all of the
features of this appliance. For more information on any feature reviewed in this document, refer to to the
Related Information section.

The example presented in this document defines one Virtual IP address (VIP) and binds three real servers, or
services, behind that VIP to be load balanced.

Prerequisites
Requirements
There are no specific requirements for this document.

Components Used
The information in this document is based on these software and hardware versions:

• WebNS version 4.10, 5, 6, 7 build 17s

• CSS 11150

The information in this document was created from the devices in a specific lab environment. All of the
devices used in this document started with a cleared (default) configuration. If your network is live, make sure
that you understand the potential impact of any command.

Cisco − Basic CSS Load−Balancing Configuration

Conventions
For more information on document conventions, refer to the Cisco Technical Tips Conventions.

Background Theory
When you create a load−balancing configuration, the two most important CSS−specific configuration
elements to understand are content rules and services.

Content rules are where the CSS's load−balancing features are customized, virtual IP address are defined,
and where the actual servers (called services) are bound to that virtual IP address. Content rules allow you to
specify load−balancing types, sticky methods, port specific Virtual IP addresses, and a host of other features.
Once a request hits a circuit VLAN on the CSS, that request is interrogated against all its content rules for a
match. Once a match has been made between particular elements of the request and a content rule, the CSS
load balances that request to all the services bound to that content rule. Each content rule must be configured
under an owner.

Services are the actual individual servers that the CSS load balances. Services are configured individually and
can be customized with a variety of keepalive types, Internet Control Message Protocol (ICMP) by default. A
group of services can also be referred to as a 'server farm.'

Configure
In this section, you are presented with the information to configure the features described in this document.

• Bridge VLANs to Ethernet Interfaces

• Number the Circuit VLANs
• Create Services and Keepalive
• Create a Content Owner
• Create a Content Rule and Virtual IP Address
• Add Services to a Content Rule

Note: To find additional information on the commands used in this document, use the IOS Command Lookup
tool.

Bridge VLANs to Ethernet Interfaces

On the CSS, it is necessary to bridge the circuit VLAN to an interface before you number that VLAN. Since
VLAN1 is always the default VLAN for any interface, in this configuration it is only necessary to manually
bridge VLAN10.

CSS150# config
CSS150(config)# interface e12
CSS150(config−if[e12])# bridge vlan 10

Number the Circuit VLANs

Here, you define an IP address for the VLAN interface from which the CSS will receive traffic. In this
configuration, the IP address is on the same subnet as the router's LAN−side interface. CSS commands are
case sensitive; circuit VLANs are referred to in all caps.

CSS150# config

Cisco − Basic CSS Load−Balancing Configuration

 CSS150(config)# circuit VLAN1
CSS150(config−circuit[VLAN1])# ip address 192.168.1.50 255.255.255.0
CSS150(config−circuit−ip[VLAN1−192.168.1.50])# exit
CSS150(config−circuit[VLAN1])# exit
CSS150(config)# circuit VLAN10
CSS150(config−circuit[VLAN10])# ip address 10.10.10.50 255.255.255.0
CSS150(config−circuit−ip[VLAN10−10.10.10.50])#

Create a Service and Keepalive

If no keepalive type is specified when you configure services, the keepalive type is set to the default of ICMP.
All services must be manually activated once created.

CSS150(config)# service www−server1

Create service <www−server1>,[y/n]:y
CSS150(config−service[www−server1])# ip address 10.10.10.1
CSS150(config−service[www−server1])# keepalive type ?
ftp Use FTP Keepalives for this service
http ; Use HTTP Keepalives for this service
icmp ; Use ICMP Keepalives for this service ( default )
named &nbs p; Name of keepalive to use.
none ; Disable keepalive for this service
script &nb sp; Use SCRIPT Keepalives for this service
tcp Use TCP Keepalives for this service
CSS150(config−service[www−server1])# keepalive type http
CSS150(config−service[www−server1])# active

Create a Content Owner

Owners exist for administrative flexibility. Multiple content rules can be grouped together under different
owners for ease of management. All content rules must exist under an owner.

CSS150(config)# owner Sample

Create owner <Sample>,[y/n]:y
CSS150(config−owner[Sample])#

Create a Content Rule and Virtual IP Address

Cisco suggests you specify a port under the content rule for two reasons: this allows more flexibility with the
Domain Name System (DNS) as several port−specific content rules can be configured with the same IP
address, and permitting only the traffic required by the service provides greater security for the services
behind the content rule. Two content rules can coexist with the same virtual IP address if there are other
criteria for the CSS to differentiate between the two, such as TCP/User Datagram Protocol (UDP) port, URL,
etc.

CSS150(config)# owner Sample

CSS150(config−owner[Sample])# content web−servers
Create content <web−servers>,[y/n]:y
CSS150(config−owner−content[Sample−web−servers])#
CSS150(config−owner−content[Sample−web−servers])#ip address 192.168.1.1
CSS150(config−owner−content[Sample−web−servers])#port 80

Add Services to a Content Rule

This is where the services are bound to the content rule, and the real servers are associated with the virtual IP
address. Once services have been added, content rules must be manually activated before the services start
listening for requests.

Cisco − Basic CSS Load−Balancing Configuration

 CSS150(config)# owner Sample
CSS150(config−owner[Sample])# content web−servers
CSS150(config−owner−content[Sample−web−servers])#add service www−server1
CSS150(config−owner−content[Sample−web−servers])#add service www−server2
CSS150(config−owner−content[Sample−web−servers])#add service www−server3
CSS150(config−owner−content[Sample−web−servers])#add service www−server4
CSS150(config−owner−content[Sample−web−servers])#active

Sample Configuration
CSS150−4# show run

!Generated on 08/28/2001 18:40:54

!Active version: ap0410017s

configure

!*************************** GLOBAL ***************************

ip route 0.0.0.0 0.0.0.0 192.168.1.100 1

!************************* INTERFACE *************************

interface e12
bridge vlan 10

!************************** CIRCUIT **************************

circuit VLAN1

ip address 192.168.1.50 255.255.255.0

circuit VLAN10

ip address 10.10.10.50 255.255.255.0

!************************** SERVICE **************************

service www−server1
ip address 10.10.10.1
keepalive type http
active

service www−server2
ip address 10.10.10.2
keepalive type http
active

service www−server3
ip address 10.10.10.3
keepalive type http
active

!*************************** OWNER ***************************

owner Sample

content web−servers
protocol tcp
port 80
add service www−server1
add service www−server2
add service www−server3
vip address 192.168.1.1
active

Cisco − Basic CSS Load−Balancing Configuration

Verify
There is currently no verification procedure available for this configuration.

Basic Troubleshooting
This section provides information you can use to troubleshoot your configuration.

Certain show commands are supported by the Output Interpreter tool, which allows you to view an analysis of
show command output.

If traffic destined to the content rule times out, and pings from the client are successful to the circuit VLAN
IP, it is a good idea to first verify the services are 'in service.' The show service command displays the status
of the services determined by the individual service keepalives. This command helps diagnose server errors. A
server only lists as being 'down' if the server has either failed to respond to its keepalive probes, or has not
been manually made 'active.'

• show summaryDisplays the relationship between owners, content rules, and services.
• show service summaryDisplays summary information for all services, including the service state,
connections, weight, and load.

Related Information
• Catalyst 6500 Series SSL Services Module Installation and Verification Note
• Downloads − Catalyst 6500/6000 Module Software
• Configuring Content Rules on the CSS
• Configuring Services on the CSS
• Configuring Service Keepalives on the CSS
• Configuring Session Persistence, Remapping, and Redirection on the CSS
• CSS Basic Configuration Guide (Software Version 7.20)

Cisco − Basic CSS Load−Balancing Configuration

 • CSS Advanced Configuration Guide (Software Version 7.20)
• Technical Support & Documentation − Cisco Systems

All contents are Copyright © 1992−2006 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Updated: Jan 20, 2006 Document ID: 12557

Cisco − Basic CSS Load−Balancing Configuration