Effect of TiO2 Addition in Al2O3:

Phase Evolution, Densification, Microstructure And

Mechanical Properties
A
THESIS SUBMITTED IN THE PARTIAL FULFILLMENT OF
THE REQUIREMENT FOR THE DEGREE OF
BATCHLOR OF TECHNOLOGY
IN
CERAMIC ENGINEERING
BY

SNEHLATA KUMARI
Roll No-109CR0676

DEPARTMENT OF CERAMIC ENGINEERING

NATIONAL INSTITUTE OF TECHNOLOGY, ROURKELA
2013
 Effect of TiO2 Addition in Al2O3:
Phase Evolution, Densification, Microstructure And
Mechanical Properties
A
THESIS SUBMITTED IN THE PARTIAL FULFILLMENT OF
THE REQUIREMENT FOR THE DEGREE OF
BATCHLOR OF TECHNOLOGY
IN
CERAMIC ENGINEERING
BY

SNEHLATA KUMARI
Roll No-109CR0676

Under the guidance of

Prof. Ranabrata Mazumder

DEPARTMENT OF CERAMIC ENGINEERING

NATIONAL INSTITUTE OF TECHNOLOGY, ROURKELA
2013
 Acknowledgement

I would like to express my heart felt gratitude to Prof. R. Mazumder, Dept. of Ceramic
Engineering, NIT Rourkela for suggesting the topic for my thesis and for their ready and able
guidance throughout the course of my preparing the report. Under his guidance, the final year
project can be completed in accordance of the planned schedule. I thank you Sir for your help,
inspiration and blessings.

I express my sincere thanks to Prof. S. K. Pratihar, Head of the Department of Ceramic

Engineering, NIT Rourkela for providing me the necessary facilities in the department. I would
express my gratitude and sincere thanks to my honorable teachers Prof. Santanu
Bhattacharyya, Prof. J. Bera, Dr. B. B. Nayak, Dr. S. K. Pal and Mr.A.Chowdhury for their
invaluable advice, constant help, encouragement, inspiration and blessings.My very special
thanks to Prof. R. Mazumder for his constant help throughout the project work.

Submitting this thesis would have been a Herculean job, without the constant help,
encouragement, support and suggestions from my seniors and friends, especially Ganesh sir,
Patibha Didi, Gita didi, for their time to help. Although it will be difficult to record my
appreciation to each and every one of them in this small space; I will relish your memoriesfor
years to come.

Last but not the least I would like to thank my parents and family members for their support,
blessing and affection. I would also express my sincere thanks to staff members of Ceramic
Engineering Department, N.I.T. Rourkela.

Date: SNEHLATA KUMARI

109CR0676
 CERTIFICATE

This is to certify that the thesis on “Effect of TiO2 Addition in Al2O3:

Phase Evolution, Densification, Microstructure And Mechanical Properties” submitted by
Miss Snehlata kumari, to the National Institute of Technology, Rourkela in partial fulfillment
of the requirements for the award of the degree of Bachelor of Technology in Ceramic
Engineering is a record of bonafide research work carried out by her under my supervision and
guidance. Her thesis, in ouropinion, is worthy of consideration for the award of degree of
Bachelor of Technology inaccordance with the regulations of the institute.

The results embodied in this thesis have not been submitted to any other university orinstitute for
the award of a Degree.

Supervisor

Prof. R. Mazumder
Department of Ceramic Engineering
National Institute of Technology
Rourkela
 Abstract

The thesis describes the effect of TiO2 additionin alumina on phase formation, densification,
microstructure and mechanical properties of the composite.The ceramic composite were
prepared with Al2O3 and TiO2 powder by solid state mixing route. The Al2O3–TiO2 powders
contain 3, 5, 10, 13, 20, and 40 wt% of TiO2. Mixed powders were calcined at
1200oC.Calcinedpowders were uniaxially pressed into cylindrical pellets and rectangular bars,
and sintered at 1600oC. X-ray powder diffraction technique was used to study the phase
evolution in calcined powder and in sintered specimen. Scanning electron microscope (SEM)
was used to find out the particle size and powder morphology of clacined power and
microstructure of sintered sample. Flexural strength and Vickers hardness were measured on
sintered sample.

Calcined powder contains only alumina and titania phase. No intermediate phase was detected.
In sintered sample Al2TiO5 phase was detected and its concentration increases with increases in
TiO2 content.TiO2 phase was disappeared for high amount of TiO2 (20 and 40wt% addition)
addition. It was found that low concentration of TiO2 (upto 10wt %) increases the density of the
composite and further increase in TiO2concentration density decreases rapidly. Presence of
Al2TiO5phase restricts the grain growth of alumina phase.Flexural strength and Vickers hardness
of Al2O3-TiO2-Al2TiO5 composite is dependent on the content of TiO2 and the presence of
Al2TiO5 phase.
 List of figures:

Figure 1: Structure of alumina, containing aluminium atoms and oxygen atoms

Figure 2: Unit cell of rutile TiO2

Figure 3 Phase diagram of Al2O3-TiO2 system

Figure 4: Flow chart for work plan

Figure 5: Vickers hardness tester and diamond like indentation

Figure 6: Schematic of three - point bending flexural strength test

Figure 7: XRD plot of powder of different composition, calcined at 12000C

Figure 8: SEM micrograph of 3% and 13% TiO2 -doped alumina sintered at1600°C for
2hrs

Figure 9: XRD pattern for sintered samples.

Figure 10: Plot for variation of relative density and bulk density with TiO2 content.

Figure11: SEM micrograph of AT-3 and AT-13 sample sintered at1600°C for 2hrs

Figure 12: SEM micrograph of AT-20 and AT-40 sample sintered at1600°C for 2hrs.

Figure 13: Flexural strength of different TiO2 added sample sintered at 1600oC

Figure 14: Vickers hardness of different TiO2 added sample sintered at 1600oC
 List of tables

Table 1: Mechanical Properties of Aluminium Oxide (99 - 99.9 wt %)

Table 2: values for bulk density, relative density and percent of phase present of different
compositions sintered at 1600oC.

Table3: Flexural strength in MPa for different percentage of TiO2 in alumina.

Table 4: Values of hardness (GPA) for different compositionof alumina and TiO2
 CONTENTS
Abstract
List of Figures
List of tables

Chapter 1 INTRODUCTION 2-3

Chapter 2 LITERATURE REVIEW 5-11
2.1 Alumina
2.2 Titania
2.3 Aluminium-titanate(Al2TiO5)
2.4 Effect of TiO2 addition on solid solubility, densification and mechanical properties

Chapter 3 MOTIVATION, OBJECTIVE AND WORK PLAN 13-14

Chapter4 EXPERIMENTAL WORK 16-19

4.1 Powder synthesis and Characterization
4.2 Powder compaction and sintering
4.3 Sintered pellets characterization
4.4 Phase analysis-X ray diffraction
4.5 Microstructure analysis-SEM
4.6 Mechanical properties measurement

Chapter 5 RESULTS AND DISCUSSION 21-32

5.1 Phase Analysis of calcined powder
5.2 Morphology of calcined powders
5.3 Phase Analysis of sintered samples
5.4 Densification behavior
5.5 Microstructure of sintered samples
5.6 Mechanical properties
5.6.1 Flexural strength
5.6.2 Vickers Hardness
Chapter 6 CONCLUSIONS 34

REFERENCES 35-36
 1

Chapter 1

INTRODUCTION
 2

Introduction:

Composites of alumina and titania are known for their high toughness, low thermal expansion,
and low thermal conductivity. These properties make alumina-titania composites desirable
materials of construction and coatings for high performance applications where thermal barriers
are required [1, 2].

Alumina-titania coatings are excellent candidates for providing protection against abrasive wear,
and are resistant to high temperature erosion with cryogenic compatibility. It has high thermal
shock resistance. With addition of titania wear resistance increases, adhesion strength increases
but hardness decreases. Thermal expansion coefficient of alumina and tiania are 8 and 7.5(10-6K-
1
). Due to the Stefan-Boltzmann law (radiated power α T4) the 300 K radiation is dominant
compared to the radiation from the shielding at 85 K. Therefore, the many parts of the radiation
shield must be blackened of the radiation shielding facing to charcoal coated cryopanels in
Cryopump. Metals have a low emissivity over the whole spectrum and thus cannot dissipate heat
by radiating in the thermal infrared region. It is well known that most polar bonding oxides show
strong efficiency of photon emission thus exhibiting a high emissivity value. Wang et.al reported
emissivity of modified Al2O3 coating on aluminum surface [3].

Some publications have pointed out the potential of Al2O3/TiO2 thermally sprayed coatings for
diverse applications on components of fusion reactors [4]. However, scarce information is found
in the literature about the optimal processing of these coatings regarding their emissive capability
and about the influence of the powder and phase composition on the functionality of the
coatings. Cockeram et. al. used different oxide based coating for enhancement of thermal
emissivity of radiator for thermo photovoltaic (TPV) power generation system. They plasma
sprayed two different commercially available Al2O3-TiO2 composition, but not disclosed exact
composition. Very high emissivity (>0.9) was reported for one composition [5]. The other
applications of Al2O3-TiO2 composites are
 TiO2/ Al2O3 films for optical application.
 Al2O3/TiO2nanocomposites to use in the femoral head of hip replacement
 Hydraulic parts
 Plungers
 3

 Automotive parts
 Textile manufacturing components and tooling
 Components for the chemical industry
 Electrical insulation and dielectric applications - Bioelectronic dielectric materials for
sensor packaging and biochips
 4

Chapter 2

LITERATURE REVIEWThe
aim of

is to carry
 5

2.1 Al2O3
Al2O3 is an oxide of aluminum a group III element. It is known to be a very stable and
robustmaterial. It possesses strong ionic interatomic bonding giving rise to it is desirable material
characteristics.Alumina is well known for its high strength and stiffness. The material's hardness
is extremely high resulting in its low wear. It can exist in several crystalline phases. The most
stable hexagonal alpha phase is at elevated temperatures. This is the phase of particular interest
for structural applications. The oxygen ions form a hexagonal close-packed structure with
aluminium ions filling two-thirds of the octahedral interstice. Each Al3+center is octahedral.

Figure 1: structure of alumina containing aluminium atoms and oxygen atoms [6].

Alpha phase alumina is the strongest and stiffest of the oxide ceramics. Alumina is well known
of its high hardness. Its high hardness, excellent dielectric properties, refractoriness and good
thermal properties make it the material of choice for a wide range of applications. However, due
to its intrinsic stiff and brittle characteristics, alumina exhibits its design limitations. Flexural
strength of alumina, which is a mechanical parameter that isassociated with brittleness the low,
makes it unable to resist deformation under load over an extended period of time [7].

In addition, the strength of alumina strongly depends on the types of actingforces or stresses as a
result of low fracture toughness and the presence of imperfections. As similar to other ceramic-
based materials, alumina has higherdegree of compressive strength; it is relatively brittle in
nature under tensile and bending stresses. Additive can be added to enhance particular desirable
material characteristics. An example would be additions of chrome oxide or manganese oxide to
 6

improve hardness and change color. TiO2 addition in alumina increases its fracture toughness.
Other additions can be made to improve the different properties of composition [8].

Table 1: Mechanical Properties of Aluminium Oxide (99 - 99.9 wt%) [11]

Hardness 15-16 GPa

Flexural Strength 550 MPa

Tensile Strength 310 MPa

Compressive Strength 3790 MPa

Fracture Toughness 4.0 MPa.m
Modulus of Elasticity 330-400 GPa

Other properties of Al2O3

 Excellent dielectric properties
 Good thermal conductivity
 Excellent size and shape capability
 It is available in different purity ranges from 94%, an easily metallizable composition, to
99.8% for the most demanding high temperature applications.
 Resists strong acid and alkali attack at elevated temperatures
High purity alumina is usable in both oxidizing and reducing atmospheres to 1925°C. It
resists attack by all gases except wet fluorine and is resistant to all common reagents
except hydrofluoric acid and phosphoric acid. Elevated temperature attack occurs in the
presence of alkali metal vapors particularly at lower purity levels.
 7

2.2 TiO2
Three different crystallographic structures of TiO2 (titania) occur in nature: Rutile -tetragonal,
Anatase-tetragonal, Brookite –orthorhombic. Out of these three polymorphs of TiO2, only rutile
is the thermodynamically most stable phase where as anatase and brookite is metastable,
transforming to rutile when they are heated. Brookite transforms into rutile at quite low
temperatures. Only the rutile and anatase play a significant role in industrial applications.
Applications of brookite are limited due to its rareness and difficult preparation [9, 10].
Figure 2 shows a schematic of a unit cell of rutile TiO2. However, anatase is typically the
majority product of inorganic syntheses and is the main constituent of nanocrystalline materials.
It has been reported that titania normally undergoes anatase - rutile phase transformation in the
temperature range from 600 to 700°C.

Figure 2.Unit cell of rutile TiO2 [11].

Titanium oxide (TiO2)-based ceramics have many desirable and potential applications.
Their mechanical properties are strongly affected by composition and microstructure, and
can thus be tailored. The optical properties of TiO2 are useful, being colorless,
transparent, and possessing a high refractive index. These properties and the ability to
 8

tailor the structure make TiO2-based ceramics suitable for a wide range of applications.
[10]

 As a semiconductor material with long-term stability,non-toxic environmental

acceptability and broadly low costavailability TiO2 has also been taken into
account for photovoltaic applications[17].
 Wide transmission range strong birefringency and good mechanical properties
of rutile make it suitable for fabrication of polarizing cubes, prisms and optical
isolators.
2.3 Aluminum- titanate (Al2TiO5)
Al2TiO5 is a synthetic ceramic material, it is considered as a candidate for many structural
applications because of its high melting point, low thermal conductivity, almost zero thermal
expansion and excellent thermal shock resistance [11]. Thus it is being tested as an insulator
material in combustion engines, e.g. as portliner in the cylinder head, piston head, manifold,
lining of turbochargers, swirl chamber and valve insulation [12]. It is belongs to a class of
ceramics having a zero thermal expansion coefficient and excellent thermal shock resistance. It
develops microcracks in the cooling step after sintering process. These fine intergranular cracks
limit the strength of the material, but provide an effective mechanism for absorbing strain energy
during thermal shock and preventing catastrophic crack propagation [11].
Furthermore, it is a good substitute of machinable BN-ceramics which is used as an insulating
substrate in current micro-electronic industry and it is are very expensive, therefore the
development of new low-cost machinable substrate ceramic are consistently required. The results
of many researches showed that this composite could be used for low-cost machinable ceramics
for the replacement of BN ceramics [12, 13]. It has almost zero thermal expansion coefficient
(0.8×10-8 oC-1) in the range of 20 to 1000oC. But this material is nevertheless unstable below
1280c and it decomposes giving rise to Al2O3 α and titanium oxide (rutile) by an eutectoid
reaction [14].
 9

Phase diagram of Al2O3 and TiO2

Figure 3: Phase diagram of Al2O3-TiO2 system [15]

2.4 Effect of TiO2 addition on solid solubility, densification and mechanical

properties
It is reported [20] that the solid solubility of TiO2 in Al2O3 is too small. It is determined by the
lattice parameter shift of Al2O3. The solid solution of TiO2 in α- Al2O3 was found at>1150oC, and
the solubility was 0.27% at 1300-1700oC. Beyond the solubility limit, excess TiO2 coexisted
with α - Al2O3 as rutile below 1350oC and as Al2TiO5 above 1450oC. The addition of TiO2 also
promoted the grain growth of Al2O3. It was seen that there is decrease in grain size beyond the
solubility limit with increasing Al2TiO5. That is Al2TiO5 existing as a second phase retards the
grain growth of Al2O3.
 10

Wan et al. [1] reported preparation of nanocomposites of alumina and titaniaby high- energy ball
milling. High density composites of alumina and titania with nanosized grains were prepared
from aluminium-titanate without using nano size powder as a starting material. The preparation
was achieved by high- energy ball milling of the aluminum titanate followed by sintering at
elevated temperature and pressure. They prepared aluminium-titanate from micron- sized
alumina and titania particles through plasma jet processing.
Hori et al. [2] reported tough corudum-rutile composite sintered body. The sintered body of
corundum-alumina and rutile-titania was prepared by adding an alkali metal to an alumina-titania
composite powder produced by a vapour-phase reaction of AlCl3 and TiCl4.It was claimed
thatcomposite body can be sintered to high density within 1280OC. The sintered body of the
invention comprised alumina of corundum phase and titania of rutile phase, which contains alkali
metal in an amount of 0.01 to 0.5 wt. % and plate shaped corundum particles whose cross
sections having aspect ratios of 2.5 or more are observed to be 10 % or more by scanning
electron micrography. This sintered body can have a high toughness by the compounding
inexpensive oxides such as alumina and titania. The toughening mechanism of the sintered body
was due to a crack deflection effect by geometrically anisotropic particles which are dispersed in
the material, and therefore the toughness is not expected to be deteriorated at high temperatures.
Lee et al. [8] prepared alumina-titania bulk composite from high-purity α-Al2O3and TiO2 powder
by hot pressing technique. The wet milling of starting powders was made in a polyethylene jar
with alumina balls and 300 ml of ethanol for 24 h. The Al2O3-TiO2 powders contain 0, 5, 10, 15,
20, and 25 mol% of TiO2. The powder mixtures were compacted in a graphite sleeve coated with
Boron nitrate (BN), and hot pressing wascarried at 1500oC and 25MPa, in an Ar gas atmosphere
for 1 h. Relative density reduced from 99% to 95% for 5% to 25 mol% TiO2 addition. Phase
composition in the sintered sample was not reported. High toughness (7 MPa.m1/2) is observed at
20 mol% TiO2 and high hardness (13 GPa) achieved at composition 10 mol% TiO2.Changes in
relative densitycouldbe due to formation of Al2TiO5 because aluminum-titanate has a slightly
lower density than alumina and titania. These increments are due to the presence of rutile and
aluminum -titanate phases disperse in alumina matrix.
Al2O3-TiO2 composite coating was generally prepared by atmospheric plasma spraying.
Properties of coating done by 13% titania shows better results than 3% titania, and 40% titania
powder. The increase in titania content increases the coating fracture toughness but hardness
 11

decreases. It also says alumina powders are also the most suitable candidates for biomedical
applications and electrical. But coating done by these compositions donot have as high a fracture
toughness as alumina 13% titania. It has been seen that alumina 3% titania coatings having a
higher fracture toughness compared to pure alumina, but it is inferior to coatings of alumina 13%
titania [11].
Serkan A ball [15] reported mechanical property of higher amount of TiO2 in alumina (40
and 48 % TiO2). According to this The micro hardness values of the Al2O3-40 wt% TiO2
are slightly higher than that of the Al2O3-48wt.%TiO2. It is shown that the micro hardness
values are depends on the amount of TiO2.This may be attributed to the variation in
microstructural differences, porosity and phase distribution. Although, originally a pure
Al2O3 single crystal micro hardness value is 11GPa. Hwang et al. [16] found that the
bending strength decreased when the TiO2 contents were near the solubility 0.2 wt. % and
above 2wt %, where the largest grain size and Al2TiO5 were shown, respectively. The
size effect and the thermal stress due to the difference of thermalexpansion coefficients
between Al2O3 and Al2TiO5 were consideredto the major factors for the reduction of the
bending strength.

\
 12

Chapter 3

MOTIVATION, OBJECTIVE AND

WORK PLAN
 13

Motivation
Alumina-titania composites are preferred materials of construction and coatings for high
performance applications where thermal barriers are required due to its high toughness, high
thermal emissivity, low thermal expansion, and low thermal conductivity and resistant to high
temperature erosion with cryogenic compatibility.There are many reports available on plasma
sprayingof ceramic coatings of Al2O3-TiO2 and its characterization. But there are very few
reports available on the Al2O3-TiO2 composite powder synthesis, pressureless sintering and its
characterization.

Objective

The objective of this research was to develop a dense ceramic-ceramic compositesystem which
have good mechanical properties and that can fit into multiple purposes.
 To prepare Al2O3–TiO2 powders containing different amount of TiO2 (3, 5, 10, 13, 20,
and 40wt %)
 To study the phase evolution in calcined powder and in sintered specimen
 To study the pressureless sintering of Al2O3/TiO2 composite
 To study the microstructure of the composites.
 To study the effect of TiO2addition on flexural strength and hardness of the sintered
specimen.
 14

Work plan

Weighing of the reactant

powder and pot milling 6 hrs

Calcination of mixed
powder at 1200oC/ 2hrs

Compaction of calcined
powder; and Sintering

SEM and XRD of

Powder calcined at 1200oC

Phase evolution and

Microstructure Mechanical
Characterization

Vickers hardness Flexural strength

Figure 4: Flow chart for work plan

 15

Chapter 4

EXPERIMENTAL WORK
 16

4.1 Powder synthesis and characterization

Six different composition Al2O3-TiO2 powders was prepared with different percentages of TiO2
in Al2O3 (3, 5, 10, 13, 20, and 40 wt% of TiO2) and designated as AT-3, AT-5 AT-10 AT-13
AT-20 AT-40, respectively. Powder weighed and then 2-propenal was added to it prepare
mixture is the kept for ball milling for 6hrs. Mixed powder is then kept for drying for 1hr and
then grinded. The above mixed powder is then kept for calcinations at 1200oC in furnace.
Calcination is a thermal treatment process in which material is heated at a temperature below its
melting point to bring a phase transformations decomposition, phase transition, or removal of a
volatile fraction. Materials heat treatment to, as in conversion of anatase to rutile phase, anatase
to rutile phase transformation takes place at 900oC. It is also done for decomposition of hydrated
minerals.
Structural analysis, phase evolution, phase transformation and morphologicalcharacterization of
the powder calcined at 1200oCwere carried out using X-Ray Diffraction.Microstructural analysis
of the calcined powder was done by using Scanning Electron Microscope.

4.2 Powder compaction and sintering

Calcined powder is mixed with binder 3% PVA (poly vinyl alcohol) and kept for drying for
some time. Binder mixed powder is then compacted uniaxially by using hydraulic press. A
stainless steel die with internal die diameter 12.5 mm was used to make pellets.For measurement
of modulus of rupture a rectangular shaped bar was compacted of length 50mm. The force used
was 4 ton and dwell time was 90 second. Prepared samples then kept in dryer for few hrs.The
green compacts were placed on alumina plates and heated from roomtemperature to 650°C held
for 1 hour at a rate 5°C /min for binder removal. Thereafter, the samples were heated to the final
sintering temperature 1600°C with a hold time of 2hrs for desire densification and properties.
The density of Sintered pellets was measure with the help of Archimedes principle. Archimedes'
principle a law of physics which states that the upward buoyant force exerted on a body
immersed in a fluid equal to the weight of the fluid displaced the body. This principle is true for
liquids and gases. Kerosene oil is used as immersion liquid (specific gravity=0.8). First sintered
pellets were weighed to take the Dry weight. After taking the weight of the dry pellets it is
 17

poured in kerosene oil in a beaker and then it is kept under vacuum for half an hour to remove
the air present in it. Suspended weight was taken in that liquid. Pellets were removed from liquid
and then soaked weight was taken.Bulk density was calculated by the following formula.

Bulk density=
–

Relative density=

4.4 Sintered pellets characterization

4.4.1 Phase analysis-X ray diffraction
Pellets were sintered at 1600oC. The phase analysis of that sintered samples was done by X-ray
diffraction technique (Philips PAN analytical, The Netherland) using CuKα radiation. The
samples were scanned in the 2θ ranges 15 to 80oC range in continuous scan mode. The scan rate
was 0.02o/sec. Phases present in the sample has been identified with the search match facility
available with Philips X’pert high score software. All diffraction methods are based on
generation of X-rays in an X-ray tube. The sample, and the diffracted rays are collected These X-
rays are directed at. A key component of all diffraction is the angle between the incident and
diffracted rays. Powder and single crystal diffraction vary in instrumentation beyond this.
To determine the weight percentage, p, of the compounds detected by XRD, it was assumed that
the most intense diffraction peak of each compound was proportional to the percentage in the
sample, and it was calculated by Eq.

Ci
p 100
j C
Where Ci represents the integral intensity corresponding to each compound identified, and jC is
the addition of the integral intensity corresponding to all the compounds identified in the sample
15
 18

4.4.2 Microstructure analysis-SEM

Microstructure of sintered pellets has been studied using Scanning Electron Microscope (JEOL -
JSM 6480LV). The generator voltage was 15 kV. Polished samples were prepared with emery
paper of grade P 400 ad P 600 untila plane and clear surface is attained. Then polished sample is
ultrasonicate in acetone to clean theSample.Itwas then thermal etched at a temperature 1500oC
below the sintering temperature for half an hour and then it is clean again kept for ultrasonication
for 3-4 times. The polished and etched samples were coated with palladium-platinum for 2-3
min. to make the surface conducting. The specimens were observed by SEM in BSE and SE
mode.
4.4.3 Mechanical properties measurement
Vickers hardness
Sintered pellets are polished and to make surface clear for indentation. The hardness test was
studied by a Vickers semi-macro hardness tester (LV-700 Leco, Japan).The indentations were
carried out at 3kgf load with 10 sec dwell time. The hardness (Hv) was calculated from the
diagonal length using theformula given below

Figure 5: Vickers hardness tester and diamond like indentation

Where, F = applied load in Newton

d= half diagonal length in μm.
 19

Flexural strength
Flexural strength (MOR) is the measure of maximum stress per unit area that a specimen can
withstand without breaking when it is bent. In other word it is defined as a material's ability to
resist deformation under load.For measuring flexural strength, three-point bending as per ASTM
standard C1161-90 was used.
For threepoint bending, the span length was 50 mm. Flexural strength was calculated by using
following formula

Where, P is the fracture load, L is the span length, W is the width and D is the breadthof
the sample

Figure 6: schematic of three - point bending flexural strength test

.
 20

Chapter 5

RESULT AND DISCUSSION

 21

5.1 Phase Analysis of calcined powder

The XRD pattern of the calcined powder of different composition was shown in the Fig.7.The
XRD pattern shows that the powder crystalline with sharp peaks. These crystalline peaks were
identified as Al2O3 and TiO2 only, no Al2TiO5 phase observed at this stage. Intensity of TiO2
phase is increases as the percentage of TiO2 in increased in the powder. Temperature used for
calcinations was 1200°C so XRD plot, shows that even for the composition containing higher
amount of TiO2, they do not contains any Al2TiO5 phase that means, at this temperature no
reaction is occurring between Al2O3 andTiO2 as alumina and titania starts reaction above
1300oC.

Figure 7: XRD plot of powder of different composition, calcined at 1200°C

5.2 Morphology of calcined powders
The powder morphology of calcined powder for four compositions (3, 13, 20, 40 wt%
TiO2) in Back Scattered Electron (BSE) mode is shown in Fig8. The bigger particles are
Al2O3 and the smaller particles are TiO2. Alumina particle has size in the range of 2-5 µm
and TiO2 has size in the submicron range. With increase in TiO2 content more plate like
 22

particles are visible in the structure. Composition having 40% TiO2 shows more plate like
particles. It is unclear that TiO2 has any role in formation plate like structure.

Al2O3–3% TiO2

Al2O3–13% TiO2
 23

Al2O3–20% TiO2

Al2O3–40% TiO2

Figure 8: SEM micrograph of (a) 3% (b)13% (c) 20% and (d) 40% TiO2 -added alumina
powder calcined at1200°C for 2hrs
 24

5.3 Phase Analysis of sintered samples

Fig.9 shows the XRD pattern of Al2O3-TiO2 compositions sintered at 1600oC. It is
evident from the figure that as the TiO2 content in the composition is increasing the
secondary phase Al2TiO5 (AT) is also increasing. For smaller percentage of TiO2, a very
small peak of AT phase was observed. It was seen that for high percentage (20 and 40
wt% TiO2) of TiO2 composition there is only Al2O3 and AT phase is present. TiO2 phase
is completely disappears for this compositions. That means, TiO2 is completely reacting
with Al2O3 and forming a secondary phase AT and it is stable at room temperature.

Figure 9: XRD pattern for sintered samples.

 25

5.4 Densification behavior

Density of all the composition sintered at 1600oC was measured and it was observed that density
(Fig.10) is increasing with increasing the percentage of TiO2 in the composition for (3-5 % TiO2)
then it is decreasing with higher amount of TiO2. Initial increase in density can be attributed to
grain boundary modification and higher diffusion rate of ionic species. It is to be noted that pure
alumina can be sintered to only less than 90% relative density at 1600oC. Lee et al. [8] got 99%
of relative density by hot pressing for 5% TiO2 added sample. We got more than 98% of density
by pressureless sintering. The decrease in density for high amount of TiO2 may be due to the
formation of secondary AT phase which has lower density than alumina and titania. High
temperature sintering (1650oC) of higher TiO2 added sample failed to enhance the density. It is
difficult to sinter Al2TiO5 phase. Table 2 shows the bulk and relative density of different
composition. Maximum density is achieved for 5% TiO2 in alumina.
Table 2: Bulk density, Relative density and percent of different phases present in 6
different compositions sintered at 1600oC
 26

4.0
100
98
96 3.8

94
92 3.6
Relative density(%)

90

Bulk density
88 3.4
86
84
3.2
82
80
78 3.0

76
74 2.8
0 5 10 15 20 25 30 35 40 45

TiO2 content (% wt)

Figure 10: Plot for variation of relative density and bulk density with TiO2 content.
.
5.5 Microstructure of sintered samples
The microstructure of sintered pellets (3 and13wt% TiO2) in Back Scattered Electron (BSE)
mode is shown in Fig. 11. The dark grains are Al2O3 and the bright grains are TiO2. It was
observed that there is a nonuniform distribution grains of TiO2 and Al2O3throughout the matrix.
A slight increase in grain growth was observed in 13% TiO2 -doped alumina compare to alumina
having 3% TiO2. Small amount of large equiaxed grains are observed in AT1-13 sample. The
average grain size of 13-15µm was in AT-13 sample.
 27

AT-3 (Al2O3–3% TiO2)

AT-13 (Al2O3–13% TiO2)

Figure11: SEM micrograph of AT-3 and AT-13 sample sintered at1600°C for 2hrs
 28

Figure 12 shows the SEM micrograph of AT-20 and AT-40 sample. There is no clear phase of
TiO2 is observed. As per the XRD pattern for sintered sample, TiO2is completely reacting with
alumina and forming secondary phase. Large numbers of pores is observed with increasing the
TiO2 percentage. Secondary phase AT have lower density than alumina and TiO2, decreases the
density of the sample. In AT-20 sample two different contrast region observed in the
microstructure. Details EDAX study required to find out the distribution of phases. For AT-40
sample this type of microstructure is absent.

Al2O3–20% TiO2
 29

Al2O3–40% TiO2

Figure 12: SEM micrograph of AT-20 and AT-40 sample sintered at1600°C for 2hrs.
5.6 Mechanical properties
5.6.1 Flexural strength
Flexural strength value gives material's ability to resist deformation under load. For measuring
flexural strength, three-point bending was used. The value obtained is written in the table for
different composition. Flexural strength is highest for 3% TiO2in alumina (164 MPa) and it
decreasing with increase in the TiO2 content. Reduction in strength can be attributed to large size
grain and equiaxed grain. This is to be mentioned that strength values of AT-20 and AT-40
should not be compared with other sample as those sample has very high density. The size effect
and the thermal stress due to the difference of thermal expansion coefficients between Al2O3 and
Al2TiO5 were considered to the major factors for the reduction of the bending strength [16].
 30

Table 3: flexural strength (in MPa) of sintered sample for different percentage of TiO2 in
alumina.
TiO2 content Flexural
in Alumina(% wt) strength
(MPa)

3 155
5 42.9
10 17.23
13 23.53
20 22.25
40 14.458

180

160

140
flexural strength(MPa)

120

100

80

60

40

20

0
0 5 10 15 20 25 30 35 40 45
TiO2 content (wt%)

Figure 13: Flexural strength of different TiO2 added sample sintered at 1600oC
 31

5.6.2 Vickers Hardness

Table 4 shows the value of hardness in GPa with respect to their composition. Highest value of
hardness is achieved for 3% TiO2, 15.658 GPa. With increasing the TiO2 content in the alumina
hardness is decreasingbut it was also seen that, increasing the percentage of TiO2 from 5 to10.
This increase of hardness is supposedthat these increments are due to the presence of rutile and
aluminum titanate phases disperse in alumina matrix. It is known that small quantities of TiO2
actsas a sintering aid and that dispersion of secondary phase increasesand enhances mechanical
properties.
This is to be mentioned that hardness values of AT-20 and AT-40 should not be compared with
other sample as those samples has very high density. Alumina containing higher amount of TiO2
shows a rapid decrease in hardness. This decrease in hardness value may be due to the presence
of high Al2TiO5 phase which produces micro cracks instability of this phase. Al2TiO5
decomposes and produces micro cracks at room temperature results in rapid decrease in hardness
[11].
Table 4: hardness value in GPA for different percentage of TiO2 in alumina

TiO2content Hardness
(% wt) (GPa)

3 15.658
5 13.034
10 13.8
13 12.63
20 4.185
40 1.75
 32

16

14

Hardness (GPa) 12

10

0
0 5 10 15 20 25 30 35 40 45
TiO2 content (%wt)

Figure 14: Vickers hardness of different TiO2 added sample sintered at 1600oC.
 33

Chapter 6

CONCLUSIONS
 34

Conclusions
The effect of TiO2 addition in alumina on phase formation, densification, microstructure and
mechanical properties of the composite was studied. The ceramic composite were prepared with
Al2O3 and TiO2 powder by solid state mixing route. The Al2O3–TiO2 powders contain 3, 5, 10,
13, 20, and 40 wt. % of TiO2.

 Calcined powder contains only alumina and titania phase. No intermediate phase was
detected because of alumina and titania starts reaction above 1300oC.
 In sintered sample Al2TiO5 phase was detected and its concentration increases with
increases in TiO2 content. TiO2 phase was disappeared for high amount of TiO2 (20 and
40wt% addition) addition.
 Al2O3 / TiO2 composite powder was sintered at 1600°C and giving maximum density for
5%TiO2 addition. 98% of relative density was achieved by pressureless sintering.
There is an increase of density is seen for 3-5 %TiO2 and then density is decreasing
rapidly with increase in TiO2 content. Initial increase in density may be attributed to
grain boundary modification and higher diffusion rate of ionic species. The
decrease in density for high amount of TiO2 may be due to the formation of
secondary Al2TiO5 phase which has lower density than alumina and titania and
which is difficult to sinter.
 Flexural strength and Vickers hardness of Al2O3-TiO2-Al2TiO5 composite is dependent
on the content of TiO2 and the presence of Al2TiO5 phase. AT-3 and AT-5 shows very
high hardness of 15.6 and 13.03 GPa respectively. Highest flexural strength (164.2 MPa)
was observed for AT-3.
 35

References
1. Wan et al.,Preparation of Nanocomposites of Alumina and Titania, US Patent 7,217,386
B2,May 15, 2007.

2. Hori, Tough Corundum-Rutile Composite Sintered Body, US Patent 4,892,850,Jan.9,

1990.

3. Y.M. Wang, H.Tiana, X.E.Shenb, L.Wena, J.H.Ouyanga, Y.Zhoua, D.C.Jiaa, L.X.Guoa,

“An elevated temperature infrared emissivity ceramic coating formed on 2024 aluminium
alloy by microarc oxidation” Ceramics International, In Press.

4. Miriam Floristán, Philipp Müller, Andreas Gebhardt, Andreas Killinger, Rainer Gadow,
Antonio Cardella, Chuanfei Li, Reinhold Stadler, Günter Zangl, Matthias Hirsch,
Heinrich P. Laqua, Walter Kasparek, “Development and testing of 140GHz absorber
coatings for the water baffle of W7-X cryopumps”, Fusion Engineering and Design 86
(2011) 1847–1850,.
5. B.V. Cockeram, D.P. Measures, A.J. Mueller, “The development and testing of
emissivity enhancement coatings for thermo photovoltaic (TPV) radiator applications”
Thin Solid Films 355-356(1999), 17-25
6. http://www.chemicals-technology.com
7. Ceramics Science and Technology Riedel, R., & Chen, I. W. (2000).
8. Soo Whon Lee , Carlos Morillo S.W. Lee et al.”Tribological and microstructural analysis
of Al2O3/TiO2 nanocomposites to use in the femoral head of hip replacement”;
Wear 255 (2003) 1040–1044.
9. R. Yılma, A.O. Kurt “Effects of TiO2 on the mechanical properties of theAl2O3–TiO2
plasma sprayed coating”, Journal of the European Ceramic Society 27 1319–132(2007).
10. J.J. MeleÂndez-MartõÂnez, M. JimeÂnez-Melendo “High temperature mechanical
behavior of aluminiumtitanate±mullite composites”; Journal of the European Ceramic
Society 21, 63-70 (2001).
11. http://www.webelements.com
12. Jae Hyun Park, Won Jae Lee, and IlSoo Kim’ “Al2TiO5-machinable Ceramics Made by
Reactive Sintering of Al2O3 and TiO2”, Journal of the Korean Ceramic Society Vol. 47,
498-502,( 2010).
 36

13. Hamanok, ”Effect of TiO2 on sintering of alumina ceramic”, J. ceram. Soc. JAP. Vol. 94,
505 (1986).
14. G.Tiloca,”Thermal stabilization of aluminium-titanate and properties of aluminium-
titanate solid solutions”;l Journal of material science 26 2809- 2814(1991).
15. SerkanAball ”Effect of TiO2 doping on microstructural properties of Al2O3-based single
crystal Ceramics” Journal of Ceramic Processing Research. Vol. 12, No. 1, pp. 21~25
(2011).
16. Chih-JenWang, Chi-Yuen Huang,”Effect of TiO2 addition on the sintering behavior,
hardness and fracture toughness of an ultrafine alumina”.Materials Science and
Engineering A 492 306–310(2008).
17. Y.P. Fu, C.C. Chang, C.H. Lin, T.S. Chin, Ceram. Int. 30 41(2004).