SAFETY DATA SHEET

1. Identification
Product identifier HumiSeal 1B51NSLU
Other means of identification
Product code HumiSeal 1B51NSLU
Recommended use Protective Coating for Printed Circuit Board
Recommended restrictions None known.
Manufacturer/Importer/Supplier/Distributor information
Manufacturer
Company name CHASE CORPORATION Zeta Drive Plant
Address 201 Zeta Drive
Pittsburgh, PA 15238
United States
Telephone 1-866-932-0800
E-mail Not available.
Emergency phone number 1-800-424-9300 Chemtrec, US
(+1)703-527-3887 Chemtrec, outside of US

2. Hazard(s) identification
Physical hazards Flammable liquids Category 2
Health hazards Acute toxicity, oral Category 4
Skin corrosion/irritation Category 2
Specific target organ toxicity, single exposure Category 3 respiratory tract irritation
Specific target organ toxicity, single exposure Category 3 narcotic effects
Environmental hazards Hazardous to the aquatic environment, acute Category 2
hazard
Hazardous to the aquatic environment, Category 2
long-term hazard
OSHA defined hazards Not classified.

Label elements

Signal word Danger

Hazard statement Highly flammable liquid and vapor. Harmful if swallowed. Causes skin irritation. May cause
respiratory irritation. May cause drowsiness or dizziness. Toxic to aquatic life. Toxic to aquatic life
with long lasting effects.

Material name: HumiSeal 1B51NSLU SDS US

166 Version #: 02 Revision date: 05-20-2015 Issue date: 01-06-2015 1/9

 Precautionary statement
Prevention Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Keep container tightly
closed. Ground/bond container and receiving equipment. Use explosion-proof
electrical/ventilating/lighting equipment. Use only non-sparking tools. Take precautionary
measures against static discharge. Avoid breathing mist or vapor. Wash thoroughly after
handling. Do not eat, drink or smoke when using this product. Use only outdoors or in a
well-ventilated area. Avoid release to the environment. Wear protective gloves/eye protection/face
protection.
Response If swallowed: Call a poison center/doctor if you feel unwell. If on skin (or hair): Take off
immediately all contaminated clothing. Rinse skin with water/shower. If inhaled: Remove person
to fresh air and keep comfortable for breathing. Call a poison center/doctor if you feel unwell.
Specific treatment (see this label). Rinse mouth. If skin irritation occurs: Get medical
advice/attention. Take off contaminated clothing and wash before reuse. In case of fire: Use
appropriate media to extinguish. Collect spillage.
Storage Store in a well-ventilated place. Keep container tightly closed. Store in a well-ventilated place.
Keep cool. Store locked up.
Disposal Dispose of contents/container in accordance with local/regional/national/international regulations.
Hazard(s) not otherwise Static accumulating flammable liquid can become electrostatically charged even in bonded and
classified (HNOC) grounded equipment. Sparks may ignite liquid and vapor. May cause flash fire or explosion.
Supplemental information 22.03% of the mixture consists of component(s) of unknown acute oral toxicity. 22.03% of the
mixture consists of component(s) of unknown acute hazards to the aquatic environment. 22.03%
of the mixture consists of component(s) of unknown long-term hazards to the aquatic
environment.

3. Composition/information on ingredients
Mixtures
Chemical name Common name and synonyms CAS number %
METHYL CYCLOHEXANE 108-87-2 70 - < 80
Other components below reportable levels 20 - < 30
*Designates that a specific chemical identity and/or percentage of composition has been withheld as a trade secret.

4. First-aid measures
Inhalation Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON
CENTER or doctor/physician if you feel unwell.
Skin contact Take off immediately all contaminated clothing. Rinse skin with water/shower. If skin irritation
occurs: Get medical advice/attention. Wash contaminated clothing before reuse.
Eye contact Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if
present and easy to do. Get medical attention if irritation develops and persists.
Ingestion Rinse mouth. If vomiting occurs, keep head low so that stomach content doesn't get into the lungs.
Get medical advice/attention if you feel unwell.
Most important May cause drowsiness and dizziness. Headache. Nausea, vomiting. Irritation of eyes and mucous
symptoms/effects, acute and membranes. Irritation of nose and throat. May cause respiratory irritation. Skin irritation. May cause
delayed redness and pain.
Indication of immediate Provide general supportive measures and treat symptomatically. Thermal burns: Flush with water
medical attention and special immediately. While flushing, remove clothes which do not adhere to affected area. Call an
treatment needed ambulance. Continue flushing during transport to hospital. Keep victim warm. Keep victim under
observation. Symptoms may be delayed.
General information Take off all contaminated clothing immediately. If you feel unwell, seek medical advice (show the
label where possible). Ensure that medical personnel are aware of the material(s) involved, and
take precautions to protect themselves. Show this safety data sheet to the doctor in attendance.
Wash contaminated clothing before reuse.

5. Fire-fighting measures
Suitable extinguishing media Water fog. Foam. Carbon dioxide (CO2). Dry chemical powder, carbon dioxide, sand or earth may
be used for small fires only.
Unsuitable extinguishing Do not use water jet as an extinguisher, as this will spread the fire.
media

Material name: HumiSeal 1B51NSLU SDS US

166 Version #: 02 Revision date: 05-20-2015 Issue date: 01-06-2015 2/9

Specific hazards arising from Vapors may form explosive mixtures with air. Vapors may travel considerable distance to a source
the chemical of ignition and flash back. This product is a poor conductor of electricity and can become
electrostatically charged. If sufficient charge is accumulated, ignition of flammable mixtures can
occur. To reduce potential for static discharge, use proper bonding and grounding procedures.
This liquid may accumulate static electricity when filling properly grounded containers. Static
electricity accumulation may be significantly increased by the presence of small quantities of water
or other contaminants. Material will float and may ignite on surface of water. During fire, gases
hazardous to health may be formed.
Special protective equipment Self-contained breathing apparatus and full protective clothing must be worn in case of fire.
and precautions for firefighters
Fire-fighting In case of fire and/or explosion do not breathe fumes. Move containers from fire area if you can do
equipment/instructions so without risk.
Specific methods Use standard firefighting procedures and consider the hazards of other involved materials.
General fire hazards Highly flammable liquid and vapor.

6. Accidental release measures

Personal precautions, Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of
protective equipment and low areas. Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area).
emergency procedures Wear appropriate protective equipment and clothing during clean-up. Avoid breathing mist or
vapor. Do not touch damaged containers or spilled material unless wearing appropriate protective
clothing. Ventilate closed spaces before entering them. Use appropriate containment to avoid
environmental contamination. Transfer by mechanical means such as vacuum truck to a salvage
tank or other suitable container for recovery or safe disposal. Local authorities should be advised if
significant spillages cannot be contained. For personal protection, see section 8 of the SDS.
Methods and materials for Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Take
containment and cleaning up precautionary measures against static discharge. Use only non-sparking tools. Keep combustibles
(wood, paper, oil, etc.) away from spilled material. This product is miscible in water.

Large Spills: Stop the flow of material, if this is without risk. Dike the spilled material, where this is
possible. Cover with plastic sheet to prevent spreading. Use a non-combustible material like
vermiculite, sand or earth to soak up the product and place into a container for later disposal.
Prevent entry into waterways, sewer, basements or confined areas. Following product recovery,
flush area with water.

Small Spills: Absorb with earth, sand or other non-combustible material and transfer to containers
for later disposal. Clean surface thoroughly to remove residual contamination.

Never return spills to original containers for re-use. For waste disposal, see section 13 of the SDS.
Environmental precautions Avoid release to the environment. Contact local authorities in case of spillage to drain/aquatic
environment. Prevent further leakage or spillage if safe to do so. Do not contaminate water. Avoid
discharge into drains, water courses or onto the ground. Use appropriate containment to avoid
environmental contamination.

7. Handling and storage

Precautions for safe handling Do not handle, store or open near an open flame, sources of heat or sources of ignition. Protect
material from direct sunlight. Explosion-proof general and local exhaust ventilation. Minimize fire
risks from flammable and combustible materials (including combustible dust and static
accumulating liquids) or dangerous reactions with incompatible materials. Handling operations that
can promote accumulation of static charges include but are not limited to: mixing, filtering,
pumping at high flow rates, splash filling, creating mists or sprays, tank and container filling, tank
cleaning, sampling, gauging, switch loading, vacuum truck operations. Take precautionary
measures against static discharges. All equipment used when handling the product must be
grounded. Use non-sparking tools and explosion-proof equipment. Avoid breathing mist or vapor.
Avoid contact with eyes, skin, and clothing. Avoid prolonged exposure. Do not taste or swallow.
When using, do not eat, drink or smoke. Wear appropriate personal protective equipment. Wash
hands thoroughly after handling. Observe good industrial hygiene practices. Avoid release to the
environment. Do not empty into drains.

For additional information on equipment bonding and grounding, refer to the Canadian Electrical
Code in Canada, (CSA C22.1), or the American Petroleum Institute (API) Recommended Practice
2003, "Protection Against Ignitions Arising out of Static, Lightning, and Stray Currents" or National
Fire Protection Association (NFPA) 77, "Recommended Practice on Static Electricity" or National
Fire Protection Association (NFPA) 70, "National Electrical Code".

Material name: HumiSeal 1B51NSLU SDS US

166 Version #: 02 Revision date: 05-20-2015 Issue date: 01-06-2015 3/9

Conditions for safe storage, Store locked up. Keep away from heat, sparks and open flame. Prevent electrostatic charge
including any incompatibilities build-up by using common bonding and grounding techniques. Avoid spark promoters. Eliminate
sources of ignition. Ground/bond container and equipment. These alone may be insufficient to
remove static electricity. Store in a cool, dry place out of direct sunlight. Store in original tightly
closed container. Store in a well-ventilated place. Keep in an area equipped with sprinklers. Store
away from incompatible materials (see Section 10 of the SDS).

8. Exposure controls/personal protection

Occupational exposure limits
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
Components Type Value
METHYL CYCLOHEXANE PEL 2000 mg/m3
(CAS 108-87-2)
500 ppm
US. ACGIH Threshold Limit Values
Components Type Value
METHYL CYCLOHEXANE TWA 400 ppm
(CAS 108-87-2)
US. NIOSH: Pocket Guide to Chemical Hazards
Components Type Value
METHYL CYCLOHEXANE TWA 1600 mg/m3
(CAS 108-87-2)
400 ppm
Biological limit values No biological exposure limits noted for the ingredient(s).
Appropriate engineering Explosion-proof general and local exhaust ventilation. Good general ventilation (typically 10 air
controls changes per hour) should be used. Ventilation rates should be matched to conditions. If
applicable, use process enclosures, local exhaust ventilation, or other engineering controls to
maintain airborne levels below recommended exposure limits. If exposure limits have not been
established, maintain airborne levels to an acceptable level. Eye wash facilities and emergency
shower must be available when handling this product.
Individual protection measures, such as personal protective equipment
Eye/face protection Face shield is recommended. Wear safety glasses with side shields (or goggles).

Skin protection
Hand protection Wear appropriate chemical resistant gloves.
Other Wear appropriate chemical resistant clothing. Use of an impervious apron is recommended.
Respiratory protection If engineering controls do not maintain airborne concentrations below recommended exposure
limits (where applicable) or to an acceptable level (in countries where exposure limits have not
been established), an approved respirator must be worn. Chemical respirator with organic vapor
cartridge.
Thermal hazards Wear appropriate thermal protective clothing, when necessary.
General hygiene When using do not smoke. Keep away from food and drink. Always observe good personal
considerations hygiene measures, such as washing after handling the material and before eating, drinking, and/or
smoking. Routinely wash work clothing and protective equipment to remove contaminants.

9. Physical and chemical properties

Appearance
Physical state Liquid.
Form Liquid.
Color Colorless
Odor Aromatic
Odor threshold Not available.
pH Does not apply.
Melting point/freezing point -195.88 °F (-126.6 °C) estimated
Initial boiling point and boiling 213.62 °F (100.9 °C) estimated
range
Flash point 39.2 °F (4.0 °C)

Material name: HumiSeal 1B51NSLU SDS US

166 Version #: 02 Revision date: 05-20-2015 Issue date: 01-06-2015 4/9

Evaporation rate Not available.
Flammability (solid, gas) Not available.
Upper/lower flammability or explosive limits
Flammability limit - lower 1.2 % estimated
(%)
Flammability limit - upper 6.7 % estimated
(%)
Explosive limit - lower (%) Not available.
Explosive limit - upper (%) Not available.
Vapor pressure 61.33 hPa estimated
Vapor density Not available.
Relative density Not available.
Solubility(ies)
Solubility (water) Negligible
Partition coefficient Not available.
(n-octanol/water)
Auto-ignition temperature 482 °F (250 °C) estimated
Decomposition temperature Not available.
Viscosity 155 - 215 cP
Viscosity temperature 77 °F (25 °C)
Other information
Brookfield viscosity 155 - 215 cP
Density 0.81 g/cm3
Flammability class Flammable IB estimated
Miscible (water) Negligible
Percent volatile 77.97 % estimated
Specific gravity 0.81
VOC (Weight %) 632 g/l estimated

10. Stability and reactivity

Reactivity The product is stable and non-reactive under normal conditions of use, storage and transport.
Chemical stability Material is stable under normal conditions.
Possibility of hazardous Hazardous polymerization does not occur.
reactions
Conditions to avoid Avoid heat, sparks, open flames and other ignition sources. Avoid temperatures exceeding the
flash point. Contact with incompatible materials.
Incompatible materials Strong oxidizing agents.
Hazardous decomposition No hazardous decomposition products are known.
products

11. Toxicological information

Information on likely routes of exposure
Ingestion Harmful if swallowed.
Inhalation Prolonged inhalation may be harmful. May cause drowsiness and dizziness. Headache. Nausea,
vomiting. May cause irritation to the respiratory system.
Skin contact Causes skin irritation.
Eye contact Direct contact with eyes may cause temporary irritation.
Symptoms related to the May cause drowsiness and dizziness. Headache. Nausea, vomiting. Irritation of nose and throat.
physical, chemical and Irritation of eyes and mucous membranes. Skin irritation. May cause redness and pain. May
toxicological characteristics cause respiratory irritation.
Information on toxicological effects

Material name: HumiSeal 1B51NSLU SDS US

166 Version #: 02 Revision date: 05-20-2015 Issue date: 01-06-2015 5/9

Acute toxicity In high concentrations, vapors are anesthetic and may cause headache, fatigue, dizziness and
central nervous system effects. Harmful if swallowed. Narcotic effects. May cause respiratory
irritation.
Product Species Test Results
HumiSeal 1B51NSLU (CAS Mixture)
Acute
Inhalation
LC25 Rabbit 9362.5752 ppm estimated
Components Species Test Results
METHYL CYCLOHEXANE (CAS 108-87-2)
Acute
Inhalation
LC25 Rabbit 7300 ppm

* Estimates for product may be based on additional component data not shown.
Skin corrosion/irritation Causes skin irritation.
Serious eye damage/eye Direct contact with eyes may cause temporary irritation.
irritation
Respiratory or skin sensitization
Respiratory sensitization Not available.
Skin sensitization This product is not expected to cause skin sensitization.
Germ cell mutagenicity No data available to indicate product or any components present at greater than 0.1% are
mutagenic or genotoxic.
Carcinogenicity This product is not considered to be a carcinogen by IARC, ACGIH, NTP, or OSHA.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not listed.
Reproductive toxicity This product is not expected to cause reproductive or developmental effects.
Specific target organ toxicity - May cause respiratory irritation. May cause drowsiness and dizziness.
single exposure
Specific target organ toxicity - Not classified.
repeated exposure
Aspiration hazard Not available.
Chronic effects Prolonged inhalation may be harmful.

12. Ecological information

Ecotoxicity Toxic to aquatic life with long lasting effects. Accumulation in aquatic organisms is expected.
Product Species Test Results
HumiSeal 1B51NSLU (CAS Mixture)
Aquatic
Fish LC50 Fish 69.7191 mg/l, 96 hours estimated
Components Species Test Results
METHYL CYCLOHEXANE (CAS 108-87-2)
Aquatic
Fish LC50 Striped bass (Morone saxatilis) 5.8 mg/l, 96 hours

* Estimates for product may be based on additional component data not shown.
Persistence and degradability No data is available on the degradability of this product.
Bioaccumulative potential Not available.
Partition coefficient n-octanol / water (log Kow)
METHYL CYCLOHEXANE 3.61
Mobility in soil No data available.
Other adverse effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation
potential, endocrine disruption, global warming potential) are expected from this component.

Material name: HumiSeal 1B51NSLU SDS US

166 Version #: 02 Revision date: 05-20-2015 Issue date: 01-06-2015 6/9

13. Disposal considerations
Disposal instructions Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Do not allow
this material to drain into sewers/water supplies. Do not contaminate ponds, waterways or ditches
with chemical or used container. Dispose of contents/container in accordance with
local/regional/national/international regulations.
Local disposal regulations Dispose in accordance with all applicable regulations.
Hazardous waste code The waste code should be assigned in discussion between the user, the producer and the waste
disposal company.
Waste from residues / unused Dispose of in accordance with local regulations. Empty containers or liners may retain some
products product residues. This material and its container must be disposed of in a safe manner (see:
Disposal instructions).
Contaminated packaging Empty containers should be taken to an approved waste handling site for recycling or disposal.
Since emptied containers may retain product residue, follow label warnings even after container is
emptied.

14. Transport information

DOT
UN number UN1263
UN proper shipping name PAINT
Transport hazard class(es)
Class 3
Subsidiary risk -
Label(s) 3
Packing group II
Special precautions for user Read safety instructions, SDS and emergency procedures before handling.
Special provisions 149, B52, IB2, T4, TP1, TP8, TP28
Packaging exceptions 150
Packaging non bulk 202
Packaging bulk 242
IATA
UN number UN1263
UN proper shipping name PAINT
Transport hazard class(es)
Class 3
Subsidiary risk -
Packing group II
Environmental hazards No.
ERG Code 3L
Special precautions for user Read safety instructions, SDS and emergency procedures before handling.
Other information
Passenger and cargo Allowed.
aircraft
Cargo aircraft only Allowed.
IMDG
UN number UN1263
UN proper shipping name PAINT
Transport hazard class(es)
Class 3
Subsidiary risk -
Packing group II
Environmental hazards
Marine pollutant No.
EmS F-E, S-D
Special precautions for user Read safety instructions, SDS and emergency procedures before handling.
Transport in bulk according to This substance/mixture is not intended to be transported in bulk.
Annex II of MARPOL 73/78 and
the IBC Code

Material name: HumiSeal 1B51NSLU SDS US

166 Version #: 02 Revision date: 05-20-2015 Issue date: 01-06-2015 7/9

DOT

IATA; IMDG

15. Regulatory information

US federal regulations This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication
Standard, 29 CFR 1910.1200.
All components are on the U.S. EPA TSCA Inventory List.
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
CERCLA Hazardous Substance List (40 CFR 302.4)
METHYL CYCLOHEXANE (CAS 108-87-2) Listed.
SARA 304 Emergency release notification
Not regulated.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not listed.
Superfund Amendments and Reauthorization Act of 1986 (SARA)
Hazard categories Immediate Hazard - Yes
Delayed Hazard - No
Fire Hazard - Yes
Pressure Hazard - No
Reactivity Hazard - No
SARA 302 Extremely hazardous substance
Not listed.
SARA 311/312 Hazardous No
chemical
SARA 313 (TRI reporting)
Not regulated.

Other federal regulations

Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List
Not regulated.
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Not regulated.
Safe Drinking Water Act Not regulated.
(SDWA)
US state regulations
US. Massachusetts RTK - Substance List
METHYL CYCLOHEXANE (CAS 108-87-2)
US. New Jersey Worker and Community Right-to-Know Act
METHYL CYCLOHEXANE (CAS 108-87-2)

Material name: HumiSeal 1B51NSLU SDS US

166 Version #: 02 Revision date: 05-20-2015 Issue date: 01-06-2015 8/9

 US. Pennsylvania Worker and Community Right-to-Know Law
METHYL CYCLOHEXANE (CAS 108-87-2)
US. Rhode Island RTK
Not regulated.
US. California Proposition 65
California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material is not known to contain
any chemicals currently listed as carcinogens or reproductive toxins.
International Inventories
Country(s) or region Inventory name On inventory (yes/no)*
Australia Australian Inventory of Chemical Substances (AICS) Yes
Canada Domestic Substances List (DSL) No
Canada Non-Domestic Substances List (NDSL) Yes
China Inventory of Existing Chemical Substances in China (IECSC) Yes
Europe European Inventory of Existing Commercial Chemical Yes
Substances (EINECS)
Europe European List of Notified Chemical Substances (ELINCS) No
Japan Inventory of Existing and New Chemical Substances (ENCS) Yes
Korea Existing Chemicals List (ECL) Yes
New Zealand New Zealand Inventory Yes
Philippines Philippine Inventory of Chemicals and Chemical Substances Yes
(PICCS)
United States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory Yes
*A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s)
A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing
country(s).

16. Other information, including date of preparation or last revision

Issue date 01-06-2015
Revision date 05-20-2015
Version # 02
HMIS® ratings Health: 2
Flammability: 3
Physical hazard: 0
NFPA ratings Health: 2
Flammability: 3
Instability: 0
Disclaimer The information offered in this data sheet is designed only as guidance for the safe use, storage
and handling of the product. This information is correct to the best of our knowledge and belief at
the date of publication, however, no guarantee is made to its accuracy. This information relates
only to the specific material designated and may not be valid for such material used in combination
with any other materials or in any other process. This material is intended for industrial use only.
No warranty, expressed or implied is made.
Revision Information Product and Company Identification: Product and Company Identification

Material name: HumiSeal 1B51NSLU SDS US

166 Version #: 02 Revision date: 05-20-2015 Issue date: 01-06-2015 9/9