Scribd
Upload
59 views2 pages

BRTF14: Tetra Optical Macro Slave Repeater

This document describes a TETRA optical macro slave repeater. It is intended for use in TETRA optical fiber systems both indoors and outdoors. It provides high flexibility in system setup by allowing communication through optical fiber between a base station optical master unit and the slave unit on the repeater side. The repeater is compact, reliable, and economical, and can be easily installed and monitored remotely using software.

Uploaded by

Dmitriy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
59 views2 pages

BRTF14: Tetra Optical Macro Slave Repeater

This document describes a TETRA optical macro slave repeater. It is intended for use in TETRA optical fiber systems both indoors and outdoors. It provides high flexibility in system setup by allowing communication through optical fiber between a base station optical master unit and the slave unit on the repeater side. The repeater is compact, reliable, and economical, and can be easily installed and monitored remotely using software.

Uploaded by

Dmitriy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

BRTF14

TETRA OPTICAL
MACRO SLAVE REPEATER
• 4W MAX ALC RF OUTPUT POWER
• HIGH SENSITIVITY
• HIGH DYNAMIC RANGE
• SMALL SIZE

This repeater is intended to use for TETRA in or outdoor optical fibre systems. It is a compact and
reliable unit, and it is especially advantageous to use it in areas where off air transmission is not preferable
(like tunnels, large buildings etc.). The base station side optical master unit can communicate through optical
fiber with slave unit on repeater side, which provides high flexibility in system build-up. This very
economical solution can be installed easily, and the repeater can be set and monitored using the bundled
remote control software.

Electrical characteristics:

Optical Repeater Technical Parameters


Remote Site
Parameters
Slave Repeater
Frequency Band Uplink 380 – 385 MHz *
Frequency Band Downlink 390 – 395 MHz *
Nominal Gain 60 dB
Gain Setting 30 to 60 dB adjustable in 1dB step
ICP3 Downlink > 68 dBm typ.
Linear Output Power +36 dBm ** @ -36dBm IM
Max. ALC Level +36 dBm **
Uplink Path Noise Figure < 5 dB @ max. gain
Pass Band Ripple < ±1,5 dB max.
Gain Stability < ±1,5 dB (within operating temp. range)
Optical Module Maximum RF Input Power +5 dBm
Optical Connectors LC/PC
RF Connectors N-female
Power Supply 100 - 240 VAC / 50 -60 Hz, optional DC 48 V
Power Consumption < 120 W
Weight 25 kg
Size 420 x 400 x 175 mm
Operating Temperature Range 0°C to +45°C (optional -25°C to +55°C ***)
Storage Temperature Range -30°C to +70°C
Local Control RS232
Remote Control Through optical fiber with master unit
Degree of Protection Outdoor
(*) Other TETRA or VHF bands are also possible.
(**) According to the customer request other downlink RF power level version also possible.
(***) with extra heatsink (40mm à 80mm)
Specifications are subject to change without notice.

BHE BONN HUNGARY ELECTRONICS Ltd. Microwave & RF Development and Manufacturing
Ipari Park Str. 10. Budapest, H-1044 * P.O.Box 164. Budapest, H-1325 Home page: www.bhe-mw.eu
Phone: +36 1 233 2138 Fax.: +36 1 233 2506 E-mail: [email protected]
BRTF14
TETRA OPTICAL
MACRO SLAVE REPEATER
Outline dimensions (mm):

Optional in 19” rack

BHE BONN HUNGARY ELECTRONICS Ltd. Microwave & RF Development and Manufacturing
Ipari Park Str. 10. Budapest, H-1044 * P.O.Box 164. Budapest, H-1325 Home page: www.bhe-mw.eu
Phone: +36 1 233 2138 Fax.: +36 1 233 2506 E-mail: [email protected]

You might also like