Vipros 358 King User Pre-Installation Guide

Vipros 358 King User Pre-installation Guide Amada America Inc.
Vipros 358 King User Pre-installation Guide
Print Date 11/05/97 Page 1 of 41

This document available on the World Wide Web at http://amada.com/support/pdf/v358kuig.pdf
Warning
Qualified personnel must complete all work.
Do not apply power to the Vipros 358 King until an A.E.S.I. (Amada
Engineering and Service Incorporated) Engineer is present and has
instructed you to do so.

Contents
Contents ....................................................................................................................................................3
Introduction ...............................................................................................................................................5
Motion Package Specifications.................................................................................................................6
Punching System Specifications...............................................................................................................7
58 Station - 4 Auto-Index Turret Configuration ...................................................................................8
Fanuc O4PC CNC Controller....................................................................................................................9
Supply Requirements..............................................................................................................................10
Installing the Electrical Power Supply ...............................................................................................11
Installing the Air Supply.....................................................................................................................12
Planning the Location of the Vipros 358 King.........................................................................................13
Lifting the Machine ............................................................................................................................14
Machine Dimensions - Plan View......................................................................................................15
Machine Dimensions - Elevation View..............................................................................................16
Machine Dimensions - End View ......................................................................................................17
Maintenance Areas ...........................................................................................................................18
The Chiller...............................................................................................................................................19
Chiller Placement ..............................................................................................................................20
Connections.......................................................................................................................................21
Foundation Requirements.......................................................................................................................22
Machine Anchoring Requirements..........................................................................................................23

Floor J-bolt Mounting Hole Detail (saw cut hole) ..............................................................................23

Floor J-bolt Mounting Hole Plan View (saw cut hole) .......................................................................24
Alternative Floor J-bolt Mounting Hole Detail (Core Drill).................................................................25
Alternative J-bolt Mounting Method Plan View (Core Drill)...............................................................26
Floor J-bolt Mounting Procedure.......................................................................................................27
Foundation Mounting Procedure ............................................................................................................29
Foundation J-bolt Detail ....................................................................................................................29
Foundation Plan View .......................................................................................................................30
Foundation Elevation View................................................................................................................31
Removing the Protective Coating ...........................................................................................................32
Machine Leveling ....................................................................................................................................33
Rocking Test......................................................................................................................................34
Floor Condition: Crowning.................................................................................................................35
Floor Condition: Slope.......................................................................................................................36
Leveling Procedure ...........................................................................................................................37

Introduction
This manual describes the tasks that the purchaser of a Vipros 358 King must complete before calling the service
organization to complete the installation and operator training.
An overview of the preparations is as follows:
Plan the location of the Vipros 358 King in the shop, taking into account all the maintenance areas indicated
on the floor plan.
Prepare the Vipros 358 King floor area as required.
Uncrate the Vipros 358 King and Fanuc O4PC control and place them on the floor.
Install the air supply.
Install the electrical supply.
Remove the protective coating from the surface of the Vipros 358 King.
Anchor the Machine to the floor or foundation using the apropriate method described in this document
Note: It is the purchaser’s responsibility to install any safety devices to ensure the safety area.

Motion Package Specifications
Travel Method X and Y axes work piece movement

Control Method X, Y, T & C
Drive Motors Fanuc AC Servo (X, Y, T, C)
Maximum Sheet Size 50.000" (Y) x 157.480" (X) with one
repositioning cycle
Maximum Sheet Thickness 0.125"
Maximum Material Weight 110 lb.
Maximum Axis Travel 78.740"(X) x 50.000"(Y)
Max. Linear Table Speed 3150 IPM
Punching Accuracy ±0.004"
Positioning Accuracy ±0.001"
Repeatability ±0.001"

Punching System Specifications
Press Capacity 33 Tons

Press Stroke 1.256"
Stroke Rate (X/Y) Stroke Length Pitch Stroke Rate
0.315" 1.000" 300/375
0.178" 1.000" 375/375
0.178" 0.078" 600/600
Maximum Hole 4.500"
Diameter
Tool Type Amada Thick Turret
Turret Rotation Speed 25 RPM
Turret Capacity 58 Stations (4 auto-index)

58 Station - 4 Auto-Index Turret Configuration
319
314 216 321
311 115 218
213
A/I 117 323
309 112 120
110 325
307 122
108
124 227
204 106 328
305 126
103
229
202
1200mm disk
58 STATION 230
A/I 4 AUTO INDEX A/I
201 VIPROS 358 KING VIPROS 368 KING
VIPROS 558 VIPROS 568 Number of
PEGA 358S Maximum Stations
231 Size Round
258 (Keyed)
132
155 334
357 135 233 ½" (12.7mm) 24 (16)
256 153 A
137 336 1¼" (31.7mm) 24 (24)
151 B
354 139
149 141 C 2" (50.8mm) 4 (4)
146 144 338
352
247 A/I 242 340 D 3½" (88.9mm) 2 (2)
350 245 343 B 1¼" (31.7mm) 2 (2)
348 Auto Index
E 4½" (114.3mm) 2 (2)

Fanuc O4PC CNC Controller
Model Fanuc O4PC

Control Function X, Y, T & C
Input Method MDI, Paper Tape, DNC
Minimum Command 0.001" (X, Y) .010 (C)
Unit
Minimum Travel Unit 0.001" (X, Y) .010 (C)
Operating Modes Automatic, MDI & Manual
Display Modes Program Contents, Position Information,
Program Check, Parameters, Tool Hit
Counter, Self Diagnostics
Interlock Displays Oil Temperature, Door Open

Supply Requirements
Electrical Power Supply Vipros 358 King 230 / 460 3ph ±10%, 28 kVA
SBC-5.5 Chiller* 230 or 460 3ph ±10%, 15 kVA
Air Supply 80 psi @ 8.8 ft³/min.

*Voltage must be specified when machine is ordered

Installing the Electrical Power Supply

The Vipros 358 King requires two electrical power sources. The first power source is supplied to the Fanuc O4PC
control. The Fanuc O4PC control should be supplied from a power line separate from those used for welding machines
or other machines that produce electrical noise. The second source is connected to the SBC-5.5 chiller.
The Vipros 358 King electrical inlet is 60" above floor level inside the magnetic enclosure located to the rear of
the Fanuc O4PC control.
The SBC-5.5 chiller electrical inlet is 48" above floor level at the end of the chiller.
Vipros King SBC 5.5 Chiller

Installing the Air Supply

The Vipros 358 King must be connected to a
compressed air system by hose or pipe. The
compressed air must be clean and dry.
Please note the following:
The minimum inner pipe diameter is ½".
The air pressure required is 80 psi.
The air volume required is 8.8 ft³/min.
The air inlet is approximately 16" above the floor

level at the rear of the Vipros 358 King.

Planning the Location of the Vipros 358 King

The following diagrams provide the details for positioning the Vipros 358 King.
No obstacles are allowed in the worksheet travel area and the ceiling must be at least 40" above the top of
the Vipros 358 King.
All of the maintenance areas recommended should be used, but at a minimum you must ensure that the
doors of the Fanuc O4PC CNC unit can be opened.
The Vipros 358 King, Fanuc O4PC control, and SBC-5.5 chiller must be protected from direct sunlight or
other heat sources.
The floor must be of sufficent quailty to addiquitly support the wieght of the machine. See Floor Mounting
Procedure for details.

Lifting the Machine
Machine Weight 16 tons.

Lifting lugs front and rear of
Machine Frame.
This cover 121." This cover

may need to may need to
be removed be removed
VIPROS 358
KING

Machine Dimensions - Plan View

Machine Dimensions - Elevation View
Y Axis Zero
Turret Center Punch Center
62.2" 19.7" 50.0"

27.6" 19.7"
11.4"
55.1"
45.5"
CNC Unit
Hydraulic
96.5" Unit
63.0"
55.2"
Material
Pass 39.6" 38.3" 8.3"
Line
7.1"
1.3"
Floor Level 38.0" 37.4" 9.8" 55.9" 38.0"
103.1"
179.1"
1.2"

Machine Dimensions - End View

Maintenance Areas
81.1"

The Chiller
The Chiller Unit is very important to the reliable operation of the Vipros 358 King.
The Chiller must be placed so that an adequate flow of air is maintained.
The position of the Chiller is flexible. The Vipros 358 King is supplied with two (2) fifteen-foot lengths of
hose to connect the Chiller to the Hydraulic Unit. The customer may supply a longer length of hose if
required.
Under normal operating conditions the Chiller may be placed against walls as shown. However for
maintenance purposes access to all sides of the Chiller may be required.
The Chiller must have a minimum of 60" of clearance above the Chiller for proper airflow.

Chiller Placement
|||

zzz
,,

yy
{{

zzz
|||
,,

yy
{{
Connections
Hydraulic Unit Chiller

Foundation Requirements
The Vipros 358 King does not require a special foundation to perform as expected, however there are minimum
requirements that an existing floor must meet in order to assure machine reliability and tool life. If the existing floor
does not meet the following minimum requirements, plans for a recommended foundation are given in the section
Foundation Mounting Procedure
The minimum acceptable floor conditions to assure a successful installation are:
The area of the floor where the machine frame is to be located must be a single, homogeneous slab in good
condition. There must be no cracks or other signs of deterioration of the floor.
The floor must be 4" to 6" thick.
The floor must be capable of supporting 3.5 tons/ft².
The floor must be level to 0.032"/ft.

If the existing floor meets the minimum requirement list above, it must still be inspected carefully when the anchor
boltholes are cut. Voids under the floor, or wetness (not associated with the hole cutting procedure) should be
considered signs of an inadequate floor and a new machine location or new foundation must be considered.
It is the customer’s responsibility to determine that the floor meets these minimum requirements. Placing the machine
on an inadequate, cracked floor, or straddling seams in a floor may be grounds for voiding the machine warranty!
Amada America, Inc. does not recommend the use of vibration isolating mounts under the machine feet, as these
devices have been shown to increase the vibration within the machine frame, increasing the likelihood of vibration
related problems. Solid leveling devices are acceptable provided they incorporate a means of anchoring the machine
to the floor with the supplied J-bolts.

Machine Anchoring Requirements

To maintain machine reliability, extend tool life, and remain level over an extended period the Vipros 358 King must be
anchored in place on an adequate floor or foundation.
At a minimum the floor must consist of a single, homogeneous slab, level to within 0.032"/ft², and capable of supporting
3.5 tons/ft². It is the purchaser’s responsibility to determine that the floor meets these minimum requirements.
Floor J-bolt Mounting Hole Detail Machine Foot
(saw cut hole) Base Plate
This machine mounting method should be used only if the

floor is of such quality that it will support the weight of the
machine with the anchor J-bolts used only for maintaining
the location of the machine. Saw cut hole in foundation
Machine Foot
5.0"
Floor Line
Supplied J-bolt
24.00"
7.0" 5."
15.75" 10.00"

Floor J-bolt Mounting Hole Plan View (saw cut hole)

Alternative Floor J-bolt Mounting Hole Detail

(Core Drill)
This machine mounting method should only be used if
the floor is of such quality that it will support the weight
of the machine with the anchor J-bolts used only for
maintaining the location of the machine.
10" Diameter Core Drill

hole in existing floor
A
A
Machine Foot
Floor Line
Supplied J-bolt

Alternative J-bolt Mounting Method Plan View (Core Drill)

Floor J-bolt Mounting Procedure

Step 1. Saw cut or Core drill a hole in the existing floor
and remove the underlying dirt to the required
24" depth.
See Floor J-bolt Mounting Hole Plan View (saw

cut hole) or Alternative J-bolt Mounting Method
Plan View (Core Drill for correct layout
dimensions of the four anchor holes required.
Step 2. Set base plate over the hole.
Step 3. Set the machine on the base plate.

Step 4. Set the J-bolt through the hole in machine foot;

attach washer and nut to hold J-bolt in place.
Step 5 Pour the Concrete.

Ensure that the J-bolt remains correctly aligned
to the machine frame during the pouring and
hardening time of the concrete.
Ensure that the concrete level is equal to the
floor level
Step 6. To complete the mounting procedure, level the

machine frame by inserting leveling shims
between the machine foot and base plate.
See Leveling the Machine section for correct

procedure.

Foundation Mounting Procedure

An ideal foundation is given on the following pages. This foundation must be used if the existing floor cannot meet the
minimum requirements to support the machine.
The foundation must consist of a single, homogeneous slab. The foundation must be level to within 0.032" / ft.
Anchoring the Vipros 358 King to the floor using the anchor-bolts supplied is essential to ensure reliable performance.
Amada generally recommends that the foundation have a minimum load bearing capacity of 3.5 ton/ft2. It is the
purchaser’s responsibility to determine that the foundation meets these requirements.
Machine Foot
The base plates, shims, anchor bolts, nuts, and washers

Base Plate
are shipped with the Vipros 358 King.
The concrete J-bolt pads should be filled after the machine

is placed on the foundation. Anchor hole in foundation
Foundation J-bolt Detail Machine

Frame
See J-bolt Mounting Procedure for proper method of mounting

machine on foundation.
Machine Foot
5.0"
Foundation Line
Supplied J-bolt
24.00"
7.0" 5."
15.75" 10.00"

Foundation Plan View

151.1"
24." 103.1"
J-bolt Centerline
48."
Machine Centerline
96."
29.5" J-bolt Centerline

14.75"
48."

Foundation Elevation View

zzzzzz
||||||
,,,,,,

yyyyyy
{{{{{{
yyyyyyyyyy
,,,,,,,,,,
,,,,,,,,,,
yyyyyyyyyy
Removing the Protective Coating

The Vipros 358 King must be thoroughly cleaned of protective coating. The sheet metal guards can be removed from
around the turret to allow cleaning of the upper and lower turrets, tool bores and die holders.
Remove the wrapping paper from the Y AXIS BALL SCREW

X and Y-axes ball screws then UPPER AND LOWER TURRETS
remove the protective coating.
Remove the wrapping paper from the

X and Y LM guides then remove the
protective coating, make sure that you
remove the paper from both sides of
the carriage.
Clean die holders one at a time.

Remove a die holder, clean and
replace it before removing the next
die holder. If the die holders are
mixed up, serious turret alignment Y AXIS LM GUIDES (1 EACH SIDE)
problems may occur.
X AXIS BALL SCREW
A suitable solvent should be used to X AXIS LM GUIDES (TOP AND BOTTOM)
remove the protective coating.

Machine Leveling
Proper Machine leveling is critical to the Vipros 358 King performing as designed.
Materials and tools required:
Supplied with the machine:
Assorted thickness machine leveling shim stock
Anchor bolts
Supplied by AESI service:
Spirit level capable of reading 0.0005"/ft
One (1) 12 ton hydraulic bottle jack
Not supplied:
Additional shim stock of 0.005" thickness may be required to achieve a properly leveled machine.

Rocking Test
After the machine frame has been leveled the use of the following G-code is necessary to determine that the machine
frame is properly leveled and balanced.
Should the machine frame vibrate or move excessively during the rocking test the machine frame must be re-leveled
using the procedure in this manual.
Should the proper leveling technique not eliminate the excessive frame motion, consideration must be given to
relocation of the machine or replacement of the existing floor with an adequate foundation.
G92 X78.740 Y50.000
G06 A.100B0
N1
G91 X-.250 TTTT (Use any valid tool number)
X.250
M97 P1
G50

Floor Condition: Crowning

The flatness of the floor plays an important step in the
Machine
leveling procedure of the machine. To properly level the
centerline
machine the weight bearing points must be as far from the
centerline of the machine frame as possible.
Should a condition known as crowning exist the weight
bearing points of the machine may not be far enough from Machine Foot
the machine centerline to ensure a stable machine. Base Plate Base Plate
Under these conditions a procedure known as Half- Crowned Weight

Shimming should be used. Floor Bearing Point
To move the weight bearing points further from the

Machine
machine centerline the use of half-shims of .125" thick on
centerline
top of the base plate as shown is recommended.
After the half-shims are installed and the machine frame
is leveled use the rocking test to determine that the
machine frame is stable enough to allow production Machine Foot
without damaging the machine.
Base Plate Base Plate
Under extreme conditions the use of half-shims may not
Crowned Weight Bearing Point
move the machine weight bearing points far enough from
Floor Half-shim
the machine centerline to ensure the machine frame is
stable.
Under these conditions a more suitable location must be
found for the machine, or a new foundation for the
machine will be necessary.

Floor Condition: Slope

The slope of the floor plays an important step in the Machine
leveling procedure of the machine. To properly level the
centerline
machine the weight bearing points must be as far from the
centerline of the machine frame as possible.
Should the floor slope excessively the weight bearing
points of the machine may not be far enough from the Machine Foot
machine centerline to ensure a stable machine. Base Plate
Base Plate
Under these conditions a procedure known as Half-
Weight Bearing Point Shim
Shimming should be used.
Sloped Floor
To move the weight bearing points further from the

Machine
machine centerline the use of half-shims of .125" thick on
centerline
top of the base plate and leveling shims as shown is
recommended.
After the half-shims are installed and the machine frame
is leveled, use the rocking test to determine that the Machine Foot
machine frame is stable enough to allow production Shim
Base Plate
without damaging the machine. Base Plate
Under extreme conditions the use of half-shims may not Weight Bearing Point
Sloped Floor Half-shim
move the machine weight bearing points far enough from
the machine centerline to ensure the machine frame is
stable.
Under these conditions a more suitable location must be

found for the machine, or a new foundation for the
machine will be necessary.

Leveling Procedure
1) Determine the high end of machine frame by placing the spirit
level on the turret to measure the level of the machine frame
in the y-axis.
.0005"/ft
2) Use the bottle jack to lift the low end of the machine frame.
Shim equally between both machine feet and the base plates
until the machine frame measures near level on the y-axis
with the turret end of the machine frame slightly higher than
Bottle
the carriage end. Jack
Shim Equaly Both Sides
3) Center the bottle jack under the carriage end of the machine
frame.
Lift the machine frame until all weight is off of the machine
feet at the carriage end of the machine frame.
Remove weight
of machine from Bottle
Lift the machine frame as little as possible to take the weight base plates Jack
off of the base plates.

4) With the machine supported on the bottle jack at the carriage

end of the machine frame and the machine feet at the turret
end of the machine frame, place the spirit level on the turret.
.0
00
Measure and record the level of the turret in the x-axis
5"
/ft
direction.
Lower the machine frame to place all machine feet in contact

with the leveling shims and base plates.
5) Lift the turret end of the machine frame to allow shimming

between the machine feet and base plates to level the
machine frame in the x-axis direction.
Repeat steps 3 to 5 until the machine frame measures level to

0.0005"/ft in step 4, then continue.
Shim to Bottle
level X-axis Jack
6) With the bottle jack supporting the weight of the carriage end
of the machine monitor the level of the turret in the x-axis as
the bottle jack is slowly lowered to place the carriage end
machine feet in contact with the base plates.
Any change in the level indicates that the carriage end of the Remove weight
Bottle
of machine from
machine needs to be leveled. base plates Jack

7) Lift the carriage end of the machine frame to allow shimming

between the machine feet and base plates to level the
carriage end of the machine frame in the x-axis direction.
Repeat steps 6 and 7 until no difference in level is noted when

the machine weight is on or off of the base plates and shims, Bottle
Shim to
then continue. level X-axis Jack
8) With all of the machine feet setting on the shims and base
plates place the spirit level on the turret to measure and note
the level of the machine frame in the y-axis.
.0005"/ft
9) Using the bottle jack lift the low end of the machine frame and
shim equally under both machine feet to level the machine
frame in the y-axis.
Repeat steps 8 to 9 until the machine frame measures level to

Bottle
0.0005"/ft in the y-axis, then continue. Jack
Shim Equaly Both Sides

10) Run the machine using the rocking test G-code to determine
that the machine frame is leveled adequately. Should
excessive movement of the machine frame be noticed check
for the conditions discussed in Floor Condition Crowning and
Floor Condition Slope.
11) Tighten the anchor bolt nuts to prevent the machine frame
from moving when in use. Monitor the machine level while
tightening the anchor bolts to assure the machine level is not
changed.
12) Lower and lock the outrigger weight support feet in place.

Amada America Inc.

7025 Firestone Blvd.
Buena Park CA. 90621
Phone: (714) 739 2111
Fax: (714) 739 4099
e-mail: [email protected]


Vipros 358 King User Pre-Installation Guide

Uploaded by

Copyright:

Available Formats

Vipros 358 King User Pre-Installation Guide

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Vipros 358 King User Pre-Installation Guide

Uploaded by

Copyright:

Available Formats

What are the main steps for leveling the machine frame?

What are the main steps for leveling the machine frame?

What should be done after leveling the machine frame?

What should be done after leveling the machine frame?

Vipros 358 King User Pre-installation Guide Amada America Inc.

Vipros 358 King User Pre-installation Guide

Print Date 11/05/97 Page 1 of 41

Print Date 11/05/97 Page 2 of 41

Print Date 11/05/97 Page 3 of 41

Floor J-bolt Mounting Hole Detail (saw cut hole) ..............................................................................23

Print Date 11/05/97 Page 4 of 41

Prepare the Vipros 358 King floor area as required.

Install the air supply.

Install the electrical supply.

Print Date 11/05/97 Page 5 of 41

Motion Package Specifications

Travel Method X and Y axes work piece movement

Print Date 11/05/97 Page 6 of 41

Punching System Specifications

Press Capacity 33 Tons

Print Date 11/05/97 Page 7 of 41

58 Station - 4 Auto-Index Turret Configuration

Print Date 11/05/97 Page 8 of 41

Fanuc O4PC CNC Controller

Model Fanuc O4PC

Print Date 11/05/97 Page 9 of 41

Air Supply 80 psi @ 8.8 ft³/min.

Print Date 11/05/97 Page 10 of 41

Installing the Electrical Power Supply

Print Date 11/05/97 Page 11 of 41

Installing the Air Supply

The minimum inner pipe diameter is ½".

The air pressure required is 80 psi.

The air volume required is 8.8 ft³/min.

The air inlet is approximately 16" above the floor

Print Date 11/05/97 Page 12 of 41

Planning the Location of the Vipros 358 King

Print Date 11/05/97 Page 13 of 41

Lifting the Machine

Machine Weight 16 tons.

This cover 121." This cover

Print Date 11/05/97 Page 14 of 41

Machine Dimensions - Plan View

Print Date 11/05/97 Page 15 of 41

Machine Dimensions - Elevation View

62.2" 19.7" 50.0"

Floor Level 38.0" 37.4" 9.8" 55.9" 38.0"

Print Date 11/05/97 Page 16 of 41

Machine Dimensions - End View

Print Date 11/05/97 Page 17 of 41

Print Date 11/05/97 Page 18 of 41

The Chiller must be placed so that an adequate flow of air is maintained.

Print Date 11/05/97 Page 19 of 41

Print Date 11/05/97 Page 21 of 41

The floor must be 4" to 6" thick.

The floor must be capable of supporting 3.5 tons/ft².

The floor must be level to 0.032"/ft.

Print Date 11/05/97 Page 22 of 41