PP2557/2019/Issue 3

Page 1 of 4

Intelligent Switch Monitor

Technical data
All data is supplied subject to change without notice. Specifications
are typical at 24V, +25°C and 50% RH unless otherwise stated.

Supply voltage 17–35 V dc

(Vmin–Vmax)
Protocol 5–13 V peak to peak
Power-up surge current 900 µA
Quiescent current 500 µA
Max current LEDs On 2 mA
Max current LEDs 500 µA
disabled
Product overview Isolator data Refer to the Short-Circuit Isolation
datasheet PP2090
Product Switch Monitor
Operating temperature – 40°C to + 70°C
Part No. SA4700-100APO
Humidity 0% to 95% RH
Digital communication XP95, Discovery and (no condensation or icing)
CoreProtocol compatible Vibration, impact and shock EN 54-17, EN 54-18
IP rating IP52
Compliance
Standards and approvals EN 54-17, EN 54-18, CPR, LPCB,
VdS, BOSEC, SBSC, FG
Dimensions 60 mm height x 150 mm width x
90 mm depth
Weight 239 g

Table 1: Digital communications protocol

Product information compatibility
Protocol Device Behaviour
The Intelligent Switch Monitor is designed to monitor the state
of one or more single pole, volt-free contacts connected on a XP95 /Discovery
† †
XP95
single pair of cables to report the status. It has a selectable
CoreProtocol† Soteria
status reporting delay making it suitable for monitoring flow
switches. †
Fire control panel dependant
Refer to Table 1 for digital communications protocol
compatibility and Table 2 for the Intelligent Switch Monitor
operating modes.
• Improved design for ease of wiring meaning faster
installation
• Contains controllable isolator *
• Address range 1 - 254 *
• Five pre-configured modes, including compatibility
mode from XP95/Discovery to CoreProtocol systems *
• Priority mode for fast response *
• Configurable input styles *
• Earth fault monitoring *
* Note: CoreProtocol enabled systems feature only, please check with your
system partner for availability.

All information in this document is given in good faith but Apollo

36 Brookside Road, Havant Tel: +44 (0)23 9249 2412 Email: [email protected] Fire Detectors Ltd cannot be held responsible for any omissions or
Hampshire, PO9 1JR, UK. Fax: +44 (0)23 9249 2754 Web: www.apollo-fire.co.uk errors. The company reserves the right to change the specifications
of products at any time and without prior notice.

MANAGEMENT
SYSTEMS
MANAGEMENT
SYSTEMS
PRODUCT
CERTIFICATION
© Apollo Fire Detectors Ltd 2019
Assessed to ISO 9001:2015 Assessed to ISO 14001:2015 Cert/LPCB ref. 010
Cert/LPCB ref. 010 Cert/LPCB ref. 010 EMS
 PP2557/2019/Issue 3
Page 2 of 4

Table 2: Intelligent Switch Monitor operating modes* Figure 1: Intelligent Switch Monitor dimensional
drawing
Mode Description

1 DIL Switch XP Mode

Switch monitor - normal resistance bands with alarm
2
delays
3 Priority switch monitor - normal resistance bands

90 mm
4 Switch monitor - N/C input with alarm delays

5 Priority switch monitor - N/C input

* CoreProtocol enabled systems only

Mechanical Construction
The Intelligent Switch Monitor (see Figure 1) is available in
the new faceplate style enclosure. This can be mounted with
the supplied back-box for surface mounting or flush mounted
using a UK double gang, flush mounting back-box of minimum
depth 30mm.

60 mm
EMC Directive 2014/30/EU
The Intelligent Switch Monitor complies with the essential
requirements of the EMC Directive 2014/30/EU, provided that
it is used as described in this datasheet.
150 mm
A copy of the Declaration of Conformity is available from
Apollo on request.

Construction Products Regulation 305/2011/EU

Table 3: Status Indications
The Intelligent Switch Monitor complies with the essential
requirements of the Construction Products Regulation Legend LED Status Description
305/2011/EU.
Poll/ISOL Flashing Green Polling LED
A copy of the Declaration of Performance is available from
Apollo on request. Poll/ISOL Continuous Yellow Isolator LED

Conformity of the Intelligent Switch Monitor with the EMC I/P Continuous Yellow Input Fault
Directive, does not confer compliance with the directive on I/P Continuous Red Input Active
any apparatus or systems connected to them.
Connectivity
Refer to Figures 2, 3 and 4 for unit connection information.
Refer to the Installation Guide 39215-163 for the installation
instructions on this product. Table 3 details the status
indications of this unit, from normal operation through to
fault conditions.
 PP2557/2019/Issue 3
Page 3 of 4

Figure 2: Intelligent Switch Monitor standard resistive monitoring mode connectivity diagram

L- L+

SWITCH MONITOR

L- L+
POLL / ISOL
0

Polarity
Sensitive

L+
1

IP- IP+
N/O N/O

1
2
4
8
16
32
64
128
MCP
DLY

L-
IP
Pre-Alarm Alarm
Contact Contact
L- L+
20k EOL 10k 1k Loop

Figure 3: Intelligent Switch Monitor normally open monitoring mode connectivity diagram
(compatible with CoreProtocol only)

L- L+

SWITCH MONITOR

L- L+
POLL / ISOL
0

Polarity
Sensitive

L+
1
IP-

1
2
4
8
16
32
64
128
MCP
DLY
IP+

L-
N/O IP
Contact
L- L+
Loop

Figure 4: Intelligent Switch Monitor normally closed monitoring mode connectivity diagram
(compatible with CoreProtocol only)

L- L+

SWITCH MONITOR
L- L+
POLL / ISOL

Polarity
Sensitive
L+

1
IP-

1
2
4
8
16
32
64
128
MCP
DLY
IP+

L-

IP
N/C
Contact
L- L+
Loop
 PP2557/2019/Issue 3
Page 4 of 4

This page has intentionally left blank