UNIVERSITY OF MUMBAI

Bachelor of Engineering
in

Electronics and Telecommunication Engineering

Direct Second Year Admitted Students for the Academic Year

2020-21(Only)

(As per AICTE guidelines with effect from the academic year 2019–2020)

(REV- 2019 ‘C’ Scheme) from Academic Year 2019 – 20

Under
FACULTY OF
SCIENCE & TECHNOLOGY
 Program Structure for Second Year Engineering Semester
III & IV
UNIVERSITY OF MUMBAI
(With Effect from 2020-2021)
Semester III

Teaching Scheme
Course Credits Assigned
Course Name (Contact Hours)
Code
Theory Pract. Tut. Theory Pract. Tut. Total
Engineering Mathematics-
ECC301 III 3 -- 1* 3 -- 1 4
Electronic Devices &
ECC302 3 -- -- 3 -- -- 3
Circuits
ECC303 Digital System Design 3 -- -- 3 -- -- 3
ECC304 Network Theory 3 -- 1 3 -- 1 4
Electronic Instrumentation
ECC305 3 -- -- 3 -- -- 3
& Control Systems
Electronic Devices &
ECL301 -- 2 -- -- 1 -- 1
Circuits Lab
ECL302 Digital System Design Lab -- 2 -- -- 1 -- 1
Electronic Instrumentation
ECL303 -- 2 -- -- 1 -- 1
& Control Systems Lab
Skill Lab: C++ and Java
ECL304 -- 4 -- -- 2 -- 2
Programming
ECM301 Mini Project 1A -- 4$ -- -- 2 -- 2
Total
15 14 2 15 07 2 24

* Should be conducted batch wise.

$ Indicates work load of a learner (Not Faculty) for Mini Project 1A. Faculty Load: 1 hour per week per four groups.

Examination Scheme
Theory
Course
Course Name Internal Assessment Term Pract.
Code End Exam. Total
Sem. Duration Work & oral
Test 1 Test 2 Avg. Exam (in Hrs)
Engineering
ECC301 20 20 20 80 3 25 -- 125
Mathematics-III
Electronic Devices &
ECC302 20 20 20 80 3 -- -- 100
Circuits
ECC303 Digital System Design 20 20 20 80 3 -- -- 100
ECC304 Network Theory 20 20 20 80 3 25 -- 125
Electronic
ECC305 Instrumentation & 20 20 20 80 3 -- -- 100
Control Systems
Electronic Devices &
ECL301 Circuits Lab -- -- -- -- -- 25 25 50
Digital System Design
ECL302 -- -- -- -- -- 25 -- 25
Lab
Electronic
ECL303 Instrumentation & -- -- -- -- -- 25 -- 25
Control Systems Lab
Skill Lab: C++ and Java
ECL304 -- -- -- -- -- 25 25 50
Programming
ECM301 Mini Project 1A -- -- -- -- -- 25 25 50
Total -- -- 100 400 -- 175 75 750
 ECC301 Engineering Mathematics-III

Course Course Name Teaching Scheme Credits

Code (Contact Hours) Assigned

Theory Pract. Tut. Theory TW/Pract Tut. Total

ECC301 Engineering 03 - 01* 03 - 01 04

Mathematics-III

Course Course Name Examination

Code Scheme
Theory Exam Term Pract Total
Internal Assessment End Dura- Work &
Sem tion Oral
Test1 Test2 Avg of Exam (in
Test 1 Hrs.)
&2

ECC301 Engineering 20 20 20 80 03 25 - 125

Mathematics-III

* Should be conducted batch wise.

Pre-requisite:
1. FEC101-Engineering Mathematics-I
2. FEC201-Engineering Mathematics-II
3. Scalar and Vector Product: Scalar and vector product of three and four vectors

Course Objectives: The course is aimed

1. To learn the Laplace Transform, Inverse Laplace Transform of various functions and its
applications.
2. To understand the concept of Fourier Series, its complex form and enhance the problem solving
skill.
3. To understand the concept of complex variables, C-R equations, harmonic functions and its conjugate
and mapping in complex plane.
4. To understand the basics of Linear Algebra.
5. To use concepts of vector calculus to analyze and model engineering problems.

Course Outcomes: After successful completion of course student will be able to:

1. Understand the concept of Laplace transform and its application to solve the real integrals in
engineering problems.
2. Understand the concept of inverse Laplace transform of various functions and its applications in
engineering problems.
3. Expand the periodic function by using Fourier series for real life problems and complex
engineering problems.
4. Understand complex variable theory, application of harmonic conjugate to get orthogonal
trajectories and analytic function.
5. Use matrix algebra to solve the engineering problems.
6. Apply the concepts of vector calculus in real life problems.
Module Detailed Contents Hrs.
Module: Laplace Transform
Definition of Laplace transform, Condition of Existence of Laplace transform.
Laplace Transform (L) of Standard Functions like 𝑒𝑎𝑡, 𝑠𝑖𝑛(𝑎𝑡), 𝑐𝑜𝑠(𝑎𝑡),
𝑠𝑖𝑛ℎ(𝑎𝑡), 𝑐𝑜𝑠ℎ(𝑎𝑡) and 𝑡 𝑛 , 𝑛 ≥ 0.
Properties of Laplace Transform: Linearity, First Shifting theorem, Second Shifting
01 Theorem, change of scale Property, multiplication by t, Division by t, Laplace Transform 7
of derivatives and integrals (Properties without proof).
Evaluation of integrals by using Laplace Transformation.

Self-learning Topics: Heaviside’s Unit Step function, Laplace Transform of

Periodic functions, Dirac Delta Function.
Module: Inverse Laplace Transform
2.1 Inverse Laplace Transform, Linearity property, use of standard formulae to find
inverse Laplace Transform, finding Inverse Laplace transform using derivatives.
2.2 Partial fractions method to find inverse Laplace transform.
02 2.3 Inverse Laplace transform using Convolution theorem (without proof). 6

Self-learning Topics: Applications to solve initial and boundary value problems

involving ordinary differential equations.

Module: Fourier Series:

3.1 Dirichlet’s conditions, Definition of Fourier series and Parseval’s Identity
(without proof).
3.2 Fourier series of periodic function with period 2𝜋 and 2l.
03 3.3 Fourier series of even and odd functions. 7
3.4 Half range Sine and Cosine Series.

Self-learning Topics: Complex form of Fourier Series, Orthogonal and

orthonormal set of functions. Fourier Transform.
Module: Complex Variables:
4.1 Function f(z) of complex variable, limit, continuity and differentiability of
f(z)Analytic function, necessary and sufficient conditions for f(z) to be
analytic (without proof).
4.2 Cauchy-Riemann equations in cartesian coordinates (without proof).
04 4.3 Milne-Thomson method to determine analytic function f(z)when real part 7
(u) or Imaginary part (v) or its combination (u+v or u-v) is given.
4.4 Harmonic function, Harmonic conjugate and orthogonal trajectories

Self-learning Topics: Conformal mapping, linear, bilinear mapping, cross ratio, fixed
points and standard transformations.
Module: Linear Algebra: Matrix Theory
5.1 Characteristic equation, Eigen values and Eigen vectors, Example based on
properties of Eigen values and Eigen vectors.(Without Proof).
5.2Cayley-Hamilton theorem (Without proof), Examples based on verification of
Cayley- Hamilton theorem and compute inverse of Matrix.
05 6
5.3 Similarity of matrices, Diagonalization of matrices. Functions of square
matrix

Self-learning Topics: Application of Matrix Theory in machine learning and

google page rank algorithms, derogatory and non-derogatory matrices.
Module: Vector Differentiation and Integral
6.1 Vector differentiation: Basics of Gradient, Divergence and Curl (Without
06 6
Proof).
6.2 Properties of vector field: Solenoidal and irrotational (conservative) vector
 fields.
6.3 Vector integral: Line Integral, Green’s theorem in a plane (Without Proof),
Stokes’ theorem (Without Proof) only evaluation.
Self-learning Topics: Gauss’ divergence Theorem and applications of Vector
calculus.
Total 39
References:

1. Advanced engineering mathematics, H.K. Das, S . Chand, Publications

2. Higher Engineering Mathematics, B. V. Ramana, Tata Mc-Graw Hill Publication
3. Advanced Engineering Mathematics, R. K. Jain and S. R. K. Iyengar, Narosa publication
4. Advanced Engineering Mathematics, Wylie and Barret, Tata Mc-Graw Hill.
5. Theory and Problems of Fourier Analysis with applications to BVP, Murray Spiegel, Schaum’s
Outline Series
6. Vector Analysis Murry R. Spiegel, Schaum’s outline series, Mc-Graw Hill Publication
7. Beginning Linear Algebra, Seymour Lipschutz, Schaum’s outline series, Mc-Graw Hill Publication
8.Higher Engineering Mathematics, Dr. B. S. Grewal, Khanna Publication

Term Work:
General Instructions:
1. Batch wise tutorials are to be conducted. The number of students per batch should be as per University pattern
for practicals.
2. Students must be encouraged to write at least 6 class tutorials on entire syllabus.
3. A group of 4-6 students should be assigned a self-learning topic. Students should prepare a
presentation/problem solving of 10-15 minutes. This should be considered as mini project in Engineering
mathematics. This project should be graded for 10 marks depending on the performance of the students.

The distribution of Term Work marks will be as follows –

1.Attendance (Theory and Tutorial) 05 marks

2.Class Tutorials on entire syllabus 10 marks
3. Mini project 10 marks

Internal Assessment Test (20-Marks):

Assessment consists of two class tests of 20 marks each. The first-class test (Internal Assessment
I) is to be conducted when approx. 40% syllabus is completed and second class test (Internal Assessment II)
will be based on remaining contents (approximately 40% syllabus but excluding contents covered in Test I).
Duration of each test shall be one hour.
End Semester Theory Examination (80-Marks):

Weightage to each of the modules in end-semester examination will be proportional to number of respective
lecture hours mentioned in the curriculum.

1. Question paper will comprise of total 06 questions, each carrying 20 marks.

2. Question No: 01 will be compulsory and based on entire syllabus wherein 4 to 5 sub- questions will
be asked.
3. Remaining questions will be mixed in nature and randomly selected from all the modules.
4. Weightage of each module will be proportional to number of respective lecture hours as mentioned in the
syllabus.
5. Total 04 questions need to be solved.
 ECC302 - Electronic Devices & Circuits

Subject Subject Name Teaching Scheme Credits Assigned

Code (Hrs.)
Theory Practical Tutorial Theory Practical Tutorial Total
ECC302 Electronic
3 - -- 3 -- -- 3
Devices &
Circuits

Subject Subject Examination Scheme

Code Name Theory Marks Term Practical Oral Total
Internal assessment End Sem. Work and Oral
Test Test Avg. Of Test Exam
1 2 1 and Test 2
ECC302 Electronic 20 20 20 80 -- -- -- 100
Devices &
Circuits

Course pre-requisite:

FEC:102 - Engineering Physics-I

FEC:201 - Engineering Physics-II
FEC:105 - Basic Electrical Engineering

Course Objectives:
1. To explain functionality different electronic devices.
2. To perform DC and AC analysis of small signal amplifier circuits.
3. To analyze frequency response of small signal amplifiers.
4. To compare small signal and large signal amplifiers.
5. To explain working of differential amplifiers and it's applications in Operational Amplifiers

Course Outcome:

After successful completion of the course student will be able to :-

1.Know functionality and applications of various electronic devices.

2.Explain working of various electronics devices with the help of V-I characteristics.
3.Derive expressions for performance parameters of BJT and MOSFET circuits.
4. Evaluate performance ofElectronic circuits (BJT and MOSFET based).
5. Select appropriate circuit for given application.
6.Design electronic circuit (BJT, MOSFET based) circuits for given specifications.
 Module Unit No. Topics Hrs.
No.
1.0 Small Signal Amplifiers 06
1.1 Concept of AC load lineand Amplification, Small signal analysis
(Zi, Zo, Av and Ai) of CE amplifier using hybrid pi model.
1.2 Small signal analysis (Zi, Zo, Av) of CS (for EMOSFET)
amplifiers.
1.3 Introduction to multistage amplifiers.(Concept, advantages &
disadvantages)
2.0 Frequency response of Small signal Amplifiers: 08

2.1 Effects of coupling, bypass capacitors and parasitic capacitors

on frequency response of single stage amplifier, Miller effect
and Miller capacitance.
2.2 High and low frequency analysis of CE amplifier.
2.3 High and low frequency analysis of CS(E-MOSFET) amplifier.

3.0 Power Amplifiers and Differential Amplifiers 06

3.1 Classification of Power Amplifiers, analysis of Class A
transformer coupledpower amplifier
3.2 E-
MOSFETDifferentialAmplifier,DCtransfercharacteristics,operatio
nwithcommonmodesignalanddifferentialmodesignal
3.3 Differentialandcommonmodegain,CMRR,differentialandcommon
modeInputimpedance
Total 20

Text books:
1. D. A. Neamen, “Electronic Circuit Analysis and Design,” Tata McGraw Hill, 2ndEdition.
2. A. S. Sedra, K. C. Smith, and A. N. Chandorkar, “Microelectronic Circuits Theory and Applications,”
International Version, OXFORD International Students, 6thEdition
3. Franco, Sergio. Design with operational amplifiers and analog integrated circuits. Vol. 1988. New York:
McGraw-Hill, 2002.

References:
1. Boylestad and Nashelesky, “Electronic Devices and Circuits Theory,” Pearson Education, 11th Edition.
2. A. K. Maini, “Electronic Devices and Circuits,” Wiley.
3. T. L. Floyd, “Electronic Devices,”Prentice Hall, 9th Edition, 2012.
4. S. Salivahanan, N. Suresh Kumar, “Electronic Devices and Circuits”, Tata Mc-Graw Hill, 3rd Edition
5. Bell, David A. Electronic devices and circuits. Prentice-Hall of India, 1999.
Internal Assessment (IA):
Two tests must be conducted which should cover at least 80% of syllabus. The average marks ofboth the tests will be
considered as final IA marks

End Semester Examination:

1. Question paper will comprise of 6 questions, each carrying 20 marks.
2. The students need to solve total 4 questions.
3: Question No.1 will be compulsory and based on entire syllabus.
4: Remaining question (Q.2 to Q.6) will be selected from all the modules.

**********
 ECC303 - Digital System Design

Course Course Teaching Scheme (Contact Credits Assigned

Code Name Hours)
Theory Practical Tutorial Theory Practical Tutorial Total
ECC303 Digital
System 02 -- -- 02 -- -- 02
Design

Course Course Examination Scheme

Code Name Theory Marks Exam Term Practical Total
Internal Assessment End Sem. Duration Work and Oral
Test1 Test2 Avg. Exam. (Hrs.)
ECC303 Digital
System 20 20 20 80 03 -- -- 100
Design

Course Pre-requisite:

FEC105 – Basic Electrical Engineering

Course Objectives:
1. To understand number system representations and their inter-conversions used in digital electronic circuits.
2. To analyze digital logic processes and to implement logical operations using various combinational logic
circuits.
3. To analyze, design and implement logical operations using various sequential logic circuits.
4. To study the characteristics of memory and their classification.
5. To learn basic concepts in VHDL and implement combinational and sequential circuits using VHDL.

Course Outcomes:
After successful completion of the course student will be able to:

1. Understand types of digital logic, digital circuits and logic families.

2. Analyze, design and implement combinational logic circuits.
3. Analyze, design and implement sequential logic circuits.
4. Develop a digital logic and apply it to solve real life problems.
5. Classify different types of memories and PLDs.
6. Simulate and implement basic combinational and sequential circuits using VHDL/Verilog.
 Unit
Topics Hrs.
No.
1.0 Number system & Logic Gates 06

Review of Binary, Octal and Hexadecimal Number Systems, their 04

1.1
inter-conversion, Binary code, Gray code and BCD code,
Binary Arithmetic, Addition, Subtraction using 1’s and 2’s

02
1.2 Digital logic gates, Universal gates, Realization using NAND and
NOR gates, Boolean Algebra, De Morgan’s Theorem
2.0 Combinational & Sequential Logic Circuits Logic Circuits
11

2.1 SOP and POS representation, K-Map up to four variables and 04

Quine-McClusky method for minimization of logic expressions

Arithmetic Circuits: Half adder, Full adder, Half Subtractor, Full

04
Subtractor, Carry Look ahead adder and BCD adder, Magnitude
2.2 Comparator

Flip flops: RS, JK, Master slave flip flops; T & D flip flops with,
2.3 Conversion of flip flops, Registers: SISO, SIPO, PISO, PIPO.
03
3.0 Different Types of Memories and Programmable Logic Devices, 03
Introduction to VHDL

Introduction: Programmable Logic Devices (PLD), 01

3.1 Programmable Logic Array (PLA), Programmable Array Logic
(PAL)
Basics of VHDL/Verilog Programming, Design and implementation
3.2 02
of adder, subtractor, multiplexer and flip flop using VHDL/Verilog
Total
20
Suggested list of experiments:
1. Simplification of Boolean functions.
2. Design AND, OR, NOT, EXOR, EXNOR gates using Universal gates: NAND and
NOR.
3. Implement Half adder, Full adder, Half subtractor and Full subtractor circuits.
4. Verify truth table of different types of flip flops.
5. Flip flop conversions JK to D, JK to T and D to TFF.
6. Design asynchronous/synchronous MOD N counter using IC7490.
7. Write VHDL/Verilog simulation code for different logic gates.

Term Work:
At least 05 experiments covering the entire syllabus must be given “Batch Wise”.
Teacher should refer the suggested list of experiments and can design additional
experiments to acquire practical design skills. The experiments\should be students
centric and attempt should be made to make experiments more meaningful, interesting
and innovative

Text Books:
1. John F. Warkerly, “Digital Design Principles and Practices”, Pearson Education, Fifth
Edition (2018).
2. Morris Mano, Michael D. Ciletti, “Digital Design”, Pearson Education, Fifth Edition (2013).
3. R. P. Jain, “Modern Digital Electronics”, Tata McGraw Hill Education, Forth Edition (2010).
4. A. Anand Kumar, “Fundamentals of Digital Circuits”, PHI, Fourth Edition (2016).
5. Volnei A. Pedroni, “Digital Electronics and Design with VHDL” Morgan Kaufmann
Publisher, First Edition (2008).
6. Stephen Brown & Zvonko Vranesic, “Fundamentals of Digital Logic with Verilog Design”,
Third Edition, MGH (2014).

Reference Books:
1. Thomas L. Floyd, “Digital Fundamentals”, Pearson Prentice Hall, Eleventh Global
Edition (2015).
2. Mandal, “Digital Electronics Principles and Applications”, McGraw Hill Education,
First Edition (2010).
3. Ronald J. Tocci, Neal S. Widmer, Gregory L. Moss “Digital Systems Principles and
Applications”, Ninth Edition, PHI (2009).
4. Donald P. Leach / Albert Paul Malvino/Gautam Saha, “Digital Principles and
Applications”, The McGraw Hill, Eight Edition (2015).
5. Stephen Brown & Zvonko Vranesic, “Fundamentals of Digital Logic Design with
VHDL”, Second Edition, TMH (2009).
6. J. Bhasker, “A Verilog HDL Primer”, Star Galaxy Press, Third Edition (1997).

NPTEL / Swayam Course:

1. Course: Digital Circuits By Prof. Santanu Chattopadhyay (IIT Kharagpur);
https://swayam.gov.in/nd1_noc20_ee70/preview

Internal Assessment (20-Marks):

Internal Assessment (IA) consists of two class tests of 20 marks each. IA-1 is to be
conducted on approximately 40% of the syllabus completed and IA-2 will be based on
remaining contents (approximately 40% syllabus but excluding contents covered in IA-
I). Duration of each test shall be one hour. Average of the two tests will be considered
as IA marks.
End Semester Examination (80-Marks):
Weightage to each of the modules in end-semester examination will be proportional to
number of respective lecture hours mentioned in the curriculum.
1. Question paper will comprise of total 06 questions, each carrying 20 marks.
2. Question No: 01 will be compulsory and based on entire syllabus wherein 4 to 5
sub-questions will be asked.
3. Remaining questions will be mixed in nature and randomly selected from all the
modules.
4. Weightage of each module will be proportional to number of respective lecture
hours as mentioned in the syllabus.
5. Total 04 questions need to be solved.
 ECC304 - Network Theory

Course Course Name Teaching Scheme Credits Assigned

Code (Hrs.)
Theory Practical Tutorial Theory Practical Tutorial Total
ECC 305 Network Theory 03 -- 01 03 -- 01 04

Course Course Name Examination Scheme

Code Theory Marks Exam. Term Practical Total
Internal assessment End Sem. Duration Work And Oral
Test Test Avg. Of Test 1 Exam (in Hrs)
1 2 and Test 2
ECC 305 Network Theory 20 20 20 80 03 25 -- 125

Course Pre-requisite:
 Basic Electrical Engineering
 Solution to Differential Equations and Laplace Transform
Course Objectives:
1. To analyze the Circuits in time and frequency domain
2. To study network Topology, network Functions, two port network
3. To synthesize passive network by various methods
Course Outcome:
After successful completion of the course student will be able to
1. Apply their knowledge in analyzing Circuits by using network theorems.
2. Apply the time and frequency method of analysis.
3. Evaluate circuit using graph theory.
4. Find the various parameters of two port network.
5. Apply network topology for analyzing the circuit.
6. Synthesize the network using passive elements.
 Module Unit Topics Hrs.
No. No.
1.0 Electrical circuit analysis and Graph Theory 09
1.1 Analysis of DC Circuits: Analysis of Circuits with dependent
sources using generalized loop and node analysis, super
mesh and super node analysis technique
Circuit Theorems: Superposition, Theremin’s, Norton’s,
Maximum Power Transfer (No numerical with AC source in
ESE).
1.2 Graph Theory: Linear Oriented Graphs, graph
terminologies
Matrix representation of a graph: Incidence matrix, Circuit
matrix, Cut-set matrix, reduced Incident matrix, Tieset
matrix, f-cutset matrix. Relationship between sub matrices
A, B &Q KVL& KCL using matrix (No numerical) .
2.0 Time&Frequency domain analysis and Network 8
Function
2.1 Time domain analysis of R-L and R-C Circuits: Forced and
natural response, initial and final values Solution using first
order differential using step signals.
Time and frequency domain analysis of R-L-C Circuits:
Forced and natural response, effect of damping factor (no
numerical )
2.2 Network functions for the one port and two port networks,
Driving point and transfer functions, Poles and Zeros of
Network functions, necessary condition for driving
pointfunctions, necessary condition for transfer functions
3.0 Two port Networks 03
3.1 Parameters: Open Circuits, short Circuit and Transmission
parameters, conditionsfor reciprocity and symmetry
3.2 Interconnections of Two-Port networks T & π representation
(Numerical on it are NOT expected in ESE).
Total 20
Textbooks :
1.Franklin F Kuo, “Network Analysis and Synthesis”, Wiley Toppan, 2nd.ed. ,1966.
2. M E Van Valkenburg, “Network Analysis”, Prentice-Hall of India Pvt Ltd, New Delhi,
26th Indian Reprint, 2000.

Reference Books:
1. A. Chakrabarti, “Circuit Theory”, DhanpatRai& Co., Delhi, 6th Edition.
2. A. Sudhakar, Shyammohan S. Palli “Circuits and Networks”, Tata McGraw-Hill education.
3. SmarajitGhosh“Network Theory Analysis & Synthesis”, PHI learning.
4. K.S. Suresh Kumar, “Electric Circuit Analysis” Pearson, 2013.
5. D. Roy Choudhury, “Networks and Systems” , New Age International, 1998.
Internal Assessment (IA):
Two tests must be conducted which should cover at least 80% of syllabus. The average marks ofboth the test will
be considered as final IA marks.

End Semester Examination:

1. Question paper will comprise of 06 questions, each carrying 20 marks.
2. The students need to solve total 04 questions.
3: Question No.1 will be compulsory and based on entire syllabus.
4: Remaining question (Q.2 to Q.6) will be selected from all the modules.

Term Work:
At least 05 assignments covering entire syllabus must be given during the “Class Wise Tutorial”. The assignments
should be students’ centric and an attempt should be made to make assignments more meaningful, interesting and
innovative.

Term work assessment must be based on the overall performance of the student with every assignment graded from
time to time. The grades will be converted to marks as per “Credit and Grading System” manual and should be
added and averaged. Based on above scheme grading and term work assessment should be done.
 ECC305 - Electronic Instrumentation & Control Systems

Subject Subject Name Teaching Scheme Credits Assigned

Code Theory Practical Tutorial Theory TW/Practical Tutorial Total
ECC305 Electronic 03 -- ----- 03 -- --- 03
Instrumentation
& Control
System

Subject Subject Name Examination Scheme

Code Theory Marks Term Practical Oral Total
Work & Oral
Internal assessment End
Sem.
Test 1 Test 2 Ave. Of Test Exam
1 and Test 2
ECC305 Electronic 20 20 20 80 -- -- -- 100
Instrumentation
& Control
System

Prerequisites: Basics of Electronics and Electrical Engineering.

Course Objectives:
1.To provide basic knowledge about the various sensors and transducers
2. To provide fundamental concepts of control system such as mathematical modeling, time response and
Frequency response.
3. To develop concepts of stability and its assessment criteria.

Course Outcomes: Students will be able to:

1. Identify various sensors, Transducers and their brief performance specification.
2. Understand principle of working of various transducer used to measure Temperature, Displacement, level
and
their application in industry
3. Determine and use models of physical systems in forms suitable for use in the analysis and design of control
systems.
 4. Evaluate the transfer functions for a given Control system.
5. Understand the analysis of system in time domain and frequency domain.
6. Predict stability of given system using appropriate criteria.

Module Section No. Topics Hrs.

No.
1. Principle of Measurement, Testing and Measuring 05
instruments
1.1 Introduction to Basic instruments: Components of
generalized measurement system, Concept of accuracy,
precision, linearity, sensitivity, resolution, hysteresis,
calibration.
1.2 Measurement of Resistance : Kelvin’s double bridge,
Wheatstone bridge and Mega ohm bridge
Measurement of Inductance: Maxwell bridge and Hey
bridge

Measurement of Capacitance: Schering bridge

2. Stability Analysis in Time Domain 05

2.1 Root locus Analysis: Root locus concept, general rules for
constructing root-locus,
Root locus analysis of control system
3 Stability Analysis in frequency domain 10

3.1 Introduction: Frequency domain specification,

Relationship between time and frequency domain
specification of system, stability margins
3.2 Bode Plot: Magnitude and phase plot, Method of plotting
Bode plot, Stability margins and analysis using bode plot.
Frequency response analysis of RC, RL, RLC circuits
3.3 Nyquist Criterion: Concept of Polar plot and Nyquist plot,
Nyquist stability criterion, gain and phase margin
Total 20

Textbooks :

1. A.K. Sawhney, “Electrical & Electronic Measurement & Instrumentation” – DRS . India
2. B.C Nakra, K.K. Cahudhary, Instrumentation Measurement and Analysis, Tata
Mc Graw Hill.
3. W.D. Cooper, “Electronic Instrumentation And Measuring Techniques” – PHI
4. Nagrath, M.Gopal, “Control System Engineering”, Tata McGraw Hill.
 5. Rangan C. S., Sarma G. R. and Mani V. S. V., "Instrumentation Devices And
Systems", Tata McGraw-Hill, 2nd Ed., 2004.
6. K.Ogata, “Modern Control Engineering, Pearson Education”, IIIrd edition.

Reference Books:
1. Helfrick&Copper, “Modern Electronic Instrumentation & Measuring Techniques” – PHI
2. M.M.S. Anand, “Electronic Instruments and instrumentation Technology”.
3. Gopal M., “Control Systems Principles and Design”, Tata McGraw Hill Publishing Co. Ltd. New
Delhi, 1998.
4. Benjamin C.Kuo, “Automatic Control Systems, Eearson education”, VIIth edition
5. Doeblin E.D., Measurement system, Tata Mc Graw Hill., 4th ed, 2003.Madan Gopal,
“Control Systems Principles and Design”, Tata McGraw hill, 7th edition,1997.
6. Normon, “Control System Engineering”, John Wiley & sons, 3rd edition.

Internal Assessment (IA):

Two tests must be conducted which should cover at least 80% of syllabus. The average marks of both the test
will be considered as final IA marks
End Semester Examination:
1. Question paper will comprise of 6 questions, each carrying 20 marks.
2. The students need to solve total 4 questions.
3: Question No.1 will be compulsory and based on entire syllabus.
4: Remaining question (Q.2 to Q.6) will be selected from all the modules.
Term Work:
Term work assessment must be based on the overall performance of the student with every assignment graded
from time to time. The grades will be converted to marks as per “Credit and Grading System” manual and
should be added and averaged. Based on above scheme grading and term work assessment should be done.
 ECL303 – Electronic Instrumentation & Control Systems Lab

Subject Subject Name Teaching Credits Assigned

Code Scheme
(Hrs.)
Theory Practical Tutorial Theory TW/Pracs Tutorial Tot
al
ECL305 Electronic -- 02 -- -- 1 -- 1
Measurement
and Control
system
Laboratory

Examination Scheme
Subject Theory Marks
Code Subject Internal assessment End Term Practica Ora Tot
Name Test 1 Test Avg. Of Test 1 Sem. Work l& l al
2 and Test 2 Exam Oral
ECL305 Electronic -- -- -- -- 25 - -- 25
Measuremen
t and Control
system
Laboratory

Course Pre-requisites: Basics of Electrical and Electronics Engineering

Signals and Systems
Course Objectives:
● Introduction to Electronics instruments for measurement of different physical and electrical parameter.
● To simulate and analyze different parameters of control system.
● To discuss stability of control system using various criteria.
Course outcomes: After successful completion of the course student will be able to
1. Explain the principle of working of various transducers and their application in industry.
2. Measure the physical and electrical parameters of various transducers and sensors.
3. Understand the concept of first order and second order systems with their frequency response.
4. Solve problems and calculate the time response specification of control system.

Laboratory plan

Maximum of 5 practicals

List of Experiments

1. Designing DC bridge for Resistance Measurement (Quarter, Half and Full bridge)
2. Designing AC bridge Circuit for capacitance measurement.
3. To inspect the relative stability of systems Root-Locus using Simulation Software.
4. To determine the frequency specification from Polar plot of system.
5. To inspect the stability of system by Nyquist plot using Simulation software.
6. To inspect the stability of system by Bode plot using Simulation software.
Term Work:

At least 05 Experiments covering entire syllabus must be given during the “Laboratory session batch wise”.
Computation/simulation-based experiments are also encouraged. The experiments should be students centric and attempt should
be made to make experiments more meaningful, interesting and innovative.
 ECL304 - Skill Lab: C++ and Java Programming

Course Course Name Teaching Scheme

Credits Assigned
Code (Hrs.)
Theory Practical Tutorial Theory Practical Tutorial Total
Skill Lab: C++
ECL304 and Java -- 04 -- -- 02 -- 02
Programming

Course Course Examination Scheme

Code Name Theory Marks
Internal assessment End
Test Test Avg. Of Sem. Term Practical
Total
1 2 Test 1 and Exam Work And Oral
Test 2
Skill Lab: C++
ECL304 and Java -- -- -- -- 25 25 50
Programming

Note: Before performing practical ‘Necessary Theory’ will be taught by concern

faculty

Course Pre-requisites:

1. FEL204 - C-Programming

Course Objectives:

1. Describe the principles of Object Oriented Programming (OOP).

2. To understand object-oriented concepts such as data abstraction, encapsulation,
inheritance and polymorphism.
3. Utilize the object-oriented paradigm in program design.
4. To lay a foundation for advanced programming.
5. Develop programming insight using OOP constructs.

Course Outcomes:

After successful completion of the course student will be able to:

1. Describe the basic principles of OOP.

2. Design and apply OOP principles for effective programming.
3. Develop programming applications using OOP language.
4. Implement different programming applications using packaging.
5. Analyze the strength of OOP.
6. Percept the Utility and applicability of OOP.
Module Unit Topics Hrs.
No. No.
1.0 C++ Control Structures 05
1.1 Branching - If statement, If-else Statement, Decision.
Looping – while, do-while, for loop
Nested control structure- Switch statement, Continue statement, Break
statement.
1.2 Array- Concepts, Declaration, Definition, Accessing array element,
One-dimensional and Multidimensional array.
2.0 Object-Oriented Programming using C++ 10
2.1 Operator Overloading- concept of overloading, operator overloading,
Overloading Unary Operators, Overloading Binary Operators, Data
Conversion, Type casting (implicit and explicit), Pitfalls of Operator
Overloading and Conversion, Keywords explicit and mutable.
Function- Function prototype, accessing function and utility function,
Constructors and destructors, Copy Constructor, Objects and Memory
requirements, Static Class members, data abstraction and information hiding,
inline function.
Constructor- Definition, Types of Constructor, Constructor Overloading,
Destructor.
2.2 Inheritance- Introduction, Types of Inheritance, Inheritance, Public and Private
Inheritance, Multiple Inheritance, Ambiguity in Multiple Inheritance, Visibility
Modes Public, Private, Protected and Friend, Aggregation, Classes Within
Classes. Deriving a class from Base Class, Constructor and destructor in Derived
Class, Overriding Member Functions, Class Hierarchies,
Polymorphism- concept, relationship among objects in inheritance
hierarchy, Runtime & Compile Time Polymorphism, abstract classes, Virtual
Base Class.
3.0 Java : Introduction, Inheritance, Polymorphism & Encapsulation 09
3.1 Programming paradigms- Introduction to programming paradigms,
Introduction to four main
Programming paradigms like procedural, object oriented, functional, and logic
& rule based. Difference between C++ and Java.
3.2 Classes and Methods: class fundamentals, declaring objects, assigning object
reference variables, adding methods to a class, returning a value, constructors,
this keyword, garbage collection, finalize() method, overloading methods,
argument passing, object as parameter, returning objects, access control, static,
final, nested and inner classes, command line arguments, variable-length
Arguments.
String: String Class and Methods in Java.
3.3 Inheritances: Member access and inheritance, super class references, Using
super, multilevel hierarchy, constructor call sequence, method overriding,
dynamic method dispatch, abstract classes, Object class.
Packages and Interfaces: defining a package, finding packages and
CLASSPATH, access protection, importing packages, interfaces (defining,
implementation, nesting, applying), variables in interfaces, extending
interfaces, instance of operator.
Total 24
Suggested list of Experiments:

Note: Before performing practical necessary Theory will be taught by concern faculty

Sr.No Write C++ Program to

1 Add Two Numbers
2 Print Number Entered by User
3 Swap Two Numbers
4 Check Whether Number is Even or Odd
5 Find Largest Number Among Three Numbers
6 Create a simple class and object.
7 Create an object of a class and access class attributes
8 Create class methods
9 Create a class to read and add two distance
10 Create a class for student to get and print details of a student.
11 Demonstrate example of friend function with class
12 Implement inheritance.

Sr.
No. Write JAVA Program to
1 Display addition of number
2 Accept marks from user, if Marks greater than 40,declare the student as
“Pass” else “Fail””
3 Accept 3 numbers from user. Compare them and declare the largest
number (Using if-else statement).
4 Display sum of first 10 even numbers using do-while loop.
5 Display Multiplication table of 15 using while loop.
6 Display basic calculator using Switch Statement.
7 Display the sum of elements of arrays.
8 Accept and display the string entered and execute at least 5 different string
functions on it.
9 Read and display the numbers as command line Arguments and display
the addition of them
10 Define a class, describe its constructor, overload the Constructors and
instantiate its object.
11 Illustrate method of overloading
12 Demonstrate Parameterized Constructor
13 Implement Multiple Inheritance using interface
14 Create thread by implementing 'runnable' interface or creating 'Thread
Class.
15 Demonstrate Hello World Applet Example
Textbooks:

1. Bjarne Stroustrup, “The C++ Programming language”, Third edition, Pearson Education.
2. Yashwant Kanitkar, “Let Us Java”, 2nd Edition, BPB Publications.
3. D.T. Editorial Services, “Java 8 Programming Black Book”, Dreamtech Press,
Edition: 2015
4. Deitel, “C++ How to Program”, 4th Edition, Pearson Education.

Reference Books:

1. Herbert Schidt, “The Complete Reference”, Tata McGraw-Hill Publishing

Company Limited, Ninth Edition.
2. Java: How to Program, 8/e, Dietal, PHI.
3. Grady Booch, James Rumbaugh, Ivar Jacobson, “The Unified Modeling
Languageser Guide”, Pearson Education.
4. Sachin Malhotra, Saurabh Chaudhary “Programming in Java”, Oxford
University Press, 2010.

Skill-Enhancement:

1. The students should be trained to code in Eclipse (an industry accepted software
tool). Also, for a given problem statement, there is need to include external
library files (other than JDK files). Moreover, the students need to be trained on
Maven (a build tool).
2. Real-life mini-problem statements from software companies (coming in for
placement) to be delegated to groups of 3-4 students each and each group to
work on the solution for 8-12 hours (last 2 lab sessions).
Software Tools:

1. Raptor-Flowchart Simulation:http://raptor.martincarlisle.com/
2. Eclipse: https://eclipse.org/
3. Netbeans:https://netbeans.org/downloads/
4. CodeBlock:http://www.codeblocks.org/
5. J-Edit/J-Editor/Blue J

Online Repository:
1. Google Drive
2. GitHub
Term Work:

At least 08 experiments (04 experiments each on C++ and JAVA) covering entire syllabus should be
set to have well predefined inference and conclusion. Teacher should refer the suggested experiments
and can design additional experiment to maintain better understanding and quality.
The experiments should be students centric and attempt should be made to make experiments more
meaningful, interesting and innovative.
Term work assessment must be based on the overall performance of the student with every
Experiments are graded from time to time.

The grades will be converted to marks as per “Choice Based Credit and Grading System” manual
and should be added and averaged. Based on above scheme grading and term work assessment should
be done.

The practical and oral examination will be based on entire syllabus. Students are encouraged to share
their experiments codes on online repository. Practical exam should cover all 08 experiments for
examination.
 ECM301 - Mini Project 1A

Course Course Name Teaching Scheme Credits Assigned

Code
(Hrs.)
Theory Practical Tutorial Theory Practical Tutorial Total
ECM301 Mini Project 1A -- 04$ -- -- 2 -- 2

Course Course Name Examination Scheme

Code
Theory Marks Term Practical Total
Work
Internal assessment End And Oral
Sem.
Test1 Test2 Avg. Of Exam
Test1
and
Test2
ECM301 Mini Project 1A -- -- -- -- 25 25 50

$ Indicates work load of a learner (Not Faculty) for Mini Project 1A. Faculty Load: 1 hour per
week per four groups.
Objectives
1. To acquaint with the process of identifying the needs and converting it into the
problem.
2. To familiarize the process of solving the problem in a group.
3. To acquaint with the process of applying basic engineering fundamentals to attempt
solutions to the problems.
4. To inculcate the process of self-learning and research.
Outcome: At the end of the course learners will be able to…
1. Identify problems based on societal /research needs.
2. Apply Knowledge and skill to solve societal problems in a group.
3. Develop interpersonal skills to work as member of a group or leader.
4. Draw the proper inferences from available results through theoretical/
experimental/simulations.
5. Analyse the impact of solutions in societal and environmental context for sustainable
development.
6. Use standard norms of engineering practices
7. Excel in written and oral communication.
8. Demonstrate capabilities of self-learning in a group, which leads to life long learning.
9. Demonstrate project management principles during project work.
Guidelines for Mini Project
• Students shall form a group of 3 to 4 students, while forming a group shall not be
allowed less than three or more than four students, as it is a group activity.
• Students should do survey and identify needs, which shall be converted into problem
statement for mini project in consultation with faculty supervisor/head of
department/internal committee of faculties.
• Students shall submit implementation plan in the form of Gantt/PERT/CPM chart,
which will cover weekly activity of mini project.
• A log book to be prepared by each group, wherein group can record weekly work
progress, guide/supervisor can verify and record notes/comments.
• Faculty supervisor may give inputs to students during mini project activity; however,
focus shall be on self-learning.
• Students in a group shall understand problem effectively, propose multiple solution and
select best possible solution in consultation with guide/ supervisor.
• Students shall convert the best solution into working model using various components
of their domain areas and demonstrate.
• The solution to be validated with proper justification and report to be compiled in
standard format of University of Mumbai.
• With the focus on the self-learning, innovation, addressing societal problems and
entrepreneurship quality development within the students through the Mini Projects, it
is preferable that a single project of appropriate level and quality to be carried out in
two semesters by all the groups of the students. i.e. Mini Project 1 in semester III and
IV. Similarly, Mini Project 2 in semesters V and VI.
• However, based on the individual students or group capability, with the mentor’s
recommendations, if the proposed Mini Project adhering to the qualitative aspects
mentioned above gets completed in odd semester, then that group can be allowed to
work on the extension of the Mini Project with suitable improvements/modifications or
a completely new project idea in even semester. This policy can be adopted on case by
case basis.
Guidelines for Assessment of Mini Project: Term
Work
• The review/ progress monitoring committee shall be constituted by head of
departments of each institute. The progress of mini project to be evaluated on
continuous basis, minimum two reviews in each semester.
• In continuous assessment focus shall also be on each individual student,
assessment based on individual’s contribution in group activity, their
understanding and response to questions.
• Distribution of Term work marks for both semesters shall be as below;
o Marks awarded by guide/supervisor based on log book : 10
o Marks awarded by review committee 10
o Quality of Project report 05

Review/progress monitoring committee may consider following points for assessment

based on either one year or half year project as mentioned in general guidelines.